How to avoid cracks on the walls_ Preparation for plastering. #eleve

Pavel Sidorik. Renovation and Finishing
79 followers
6 Video Views·Dec 11, 2022
Hello friends
This is Pavel Sidorik and this is a channel about repairs and decoration
In this video you will see the entire process of
preparing various bases for plaster as well as how
Avoid cracks in gas concrete
block partitions Two methods
of wall reinforcement
It turned out that there are five different types of walls in the apartment
Partitions made of gas silicate blocks are the most vulnerable
cracks in the walls
The bathroom walls are made of silicate blocks they are silicate
Brick do not confuse with gas concrete blocks
There are monolithic load-bearing foundations including
Pipe channels which are often
problematic areas Because
of the smooth surface the plaster is peeling off
Partially I left the drywall from the developer
because it's even just requires a little adjustment
There are problem areas where the plaster from the developer is peeling
It fell off and left just a
splatter on the aerated concrete blocks
And of course the most beloved spots
for finishers are the
joints between different materials where cracks most
often form These include the corners
I will start with preparing various bases
for plaster and subsequent finishing
The builder's plaster
was surprisingly even
I didn't knock her down but
this kind of plaster still needs refinement
Very often the final stage of the plastering done by the developer
- smoothing and finishing - is not done according to the technology
Because for them the main thing is
the volume and appearance and quality
is the tenth thing Therefore now on the sites I always try to clean
Gypsum milk from the walls using a sander
Removing plaster manually is not the best idea
It is best to use a
grinder of the Giraffe type for
this purpose If you don't have one you can rent it
Or buy an inexpensive one
For rough plaster wall putty and removal of old wallpaper
Old finish coatings such as varnish
or paint are expensive and unnecessary
This is the DLT-R7232 model - a reliable
workhorse For those interested the link to it will be in the description
Sandpaper of the specified grade is suitable for removing plaster
60 or 80 with holes for the vacuum cleaner to create suction
For areas that the sander cannot reach I
use a regular block with coarse sandpaper
We attach the disk so that the holes in the
sandpaper align with the holes in the plate
I start working The grinder is connected
to the vacuum which allows
working without dust
The vacuum sucks the sander to the wall and it
is much more stable It cleans and does not jump
Plus the hands never get tired from holding the machine in place
When comparing mechanized cleaning and manual cleaning this is
Just sky and earth
The danger of incorrect glazing is that everything
The subsequent materials
applied to the wall may flake off
along with this gypsum plaster
Since the builders don't have time to soften
the plaster and smooth it out during work
Then they just mix the
plaster until it's liquid and apply it to the walls
It creates a wet-on-wet effect something
sticks and something peels away from the base
This does not mean that all the developer's plaster is bad
Just I had precedents and at the final stage I don't
need surprises After cleaning
the wall becomes smoother
Note the cloudiness that remains
after cleaning this erases the bumps
The wall ends up
rough which is better for the plaster
to adhere to Another problem is the rounded corners
This problem is solved using a chisel and block with
sandpaper In general removing
plaster even of good quality
This is a common phenomenon at the moment
The quality is better
Thus the plastering by the developer is prepared
ot only for filler but also if you happen to
decide to apply a leveling layer of plaster on top
The most important rule in this
case is that the leveling
layer can be applied to a stronger base not the other way around
The radiators are being removed and everything behind them is being cleaned
This is how I clean all the plaster from the developer
In the apartment
Cleaning takes not too long in terms of time
it takes me about 15 to 25 minutes per wall
I started with the dustier tasks after everything was cleaned
everything needs to be vacuumed wiped down and then primed
All reasons
To speed up the priming process I usually use
without a vacuum but in the comments I often get messages that you have
There is a vacuum pump but we don't have one what to do there is an alternative
An alternative is a garden sprayer or roller
For the next step I use a tested primer
Deep penetration of Cerezit ST-17 PRO
Drying time is 2 hours for subsequent material
application The composition
contains a yellow pigment
It allows to identify an already prepared surface
Painting the primer starts with the ceiling
In general about the preparation and plastering of the ceiling will be
A separate video where I will explain everything in detail
Just to speed up the work the wall preparation steps
The ceiling and walls are done at the same time
There is nothing complicated about spraying the walls with a sprayer
Just apply evenly and make sure it
doesn't get on the radiators and windows
Everything that can get dirty should be moved out of
the room before applying primer
Garden sprinklers are inexpensive but at the
same time significantly speed up the work
Highly absorbent bases are primed twice
At my site the highly absorbent bases
Partition walls made of gas concrete blocks
The primer is first diluted one to one with water
Then it is applied with a sprayer
onto the wall made of blocks
The second coat is applied two hours after the first
layer is completely dry but it is no longer diluted
Thus the absorbency of the base is reduced This
is important for plastering as rapid moisture loss
Promotes cracking in the solution
Thus the walls are primed throughout the apartment
The next step is to apply a plaster
to the cornices and reinforce the facade walls with a mesh
He refers
to walls built from gas concrete blocks I will
show you two options
The first option is
the classic one using a plaster and adhesive mixture
The second option is when the grid
is embedded directly into the plaster
Use the CERIZIT ST85 adhesive mixture for the first option
It is reinforced with microfibers and is very suitable for
Creating a basic
plaster layer First I mix a small
amount to fill the grooves
Cables are bundled and hidden in
the holes for junction boxes
If necessary these holes can be stuffed
with crumpled paper before plastering
Some comrades think that if the wall is plastered
You don't need to make grooves for electrical
wiring because the plaster will hide the cables
In fact that's not the case
Straps are always required because plaster does not
always cover the wiring with the necessary layer
But if the slings are not sealed there is a possibility of that
A trench will appear in the area of the strip because
the plaster layer becomes thicker and will settle
This refers to the walls of the mesh
The ropes are covered throughout the apartment
Here I made a mistake
and covered the strap before the time
We still need to install the underfloor heating cables and temperature sensor
We will have to make a new groove later
For reinforcement I use 160 gram facade mes
millimeter 5 by 5 millimeter cell
This grid has been treated with an alkaline solution its
It does not corrode the cement glue
I measure the required length so that there
will be a grid extension to the ceiling
The roll is unrolled throughout the entire apartment according to the pattern
This conveyor-like work accelerates the process
I estimated
the wall area in advance so as not to waste anything
After I have loosened all the mesh I mix a
large amount of glue and start reinforcing
Gas silicate blocks must be reinforced
Silicate blocks expanded clay concrete blocks and bricks are less prone to
Deformations so reinforcement
is not necessary but if you
do reinforce them it won't be worse it will just better
It is advisable to place something
underneath before applying the glue to the wall
First the glue is applied in patches then it
is spread evenly over the wall with a trowel
Then the facing mesh is pressed into the
adhesive and covered with a second layer
Some glue is pressed through the mesh if it is
not enough then more is taken from the bucket
The next strip is applied with a 10 cm overlap o
The previous one where necessary is inserted 10 cm at angle
This room is ready
Now it is possible to move to the next room
We reinforce all the block walls in the apartment
In most cases this reinforcement allows to avoid
appearance of cracks in gas concrete block partitions
Mesh is certainly not a panacea if the house settles
well it may tear the mesh but nevertheless reinforceme
This is the only method that effectively
prevents cracks from appearing
During the reinforcement I made a mesh release on the ceiling
in order to reinforce the corner ceiling and wall
After the reinforcement layer has dried the base is primed
Two times deep-penetrating primer ST-17
In areas without
reinforcing mesh just the corners are glued
We cut the mesh into strips of 20 centimeters
If you need to glue a lot of strips then
It is advisable to cut the roll without
unrolling it using a angle grinder
Then glue is applied in the corner and the mesh is
embedded in exactly the same way I reinforced the walls
We seal all the corners in the bathroom and the toilet
This is what it looks like when it's finished
Special attention should be given to the junction of different
materials this is a potential area where cracks may appear
Now I will show you several
ways to avoid cracks
There was only one direct joint
of different materials in my apartment
I have already filled it
Right now I'm just showing the options on the wall
I'm modeling the joint of different materials on the wall
I drew an imitation of the connection between two different
materials on the wall on this side it is a monolithic
The wall here is where the block wall begins
Very often at this point where two materials meet
a crack appears
The classic reinforcement of such a crack is when a
material is applied which can be a plastering adhesive
A mixture which may be joint compound is applied then the
wall mesh is pressed into it and covered with another layer
With a single layer of plastering and bonding compound
This is the classic option
There are more technologically advanced options
Now let's look at the next option
First of all regarding this option and this option
If your seam is filled with solution you must
definitely clear it and fill it with construction foam
The second option differs from the first by using
an additional sealing tape for the drywall profile
The tape is applied to the joint and then a layer is applied on top
Gypsum board adhesive or plastering compound
and the mesh is applied
A second layer of glue is applied on top
The advantage of this option is that the crack appears
under the sealing tape but does not come outwards
The third option differs in the type of tape
Instead of the sealing tape for the profile you can
Use the StrideFlex tape
They are composite slightly stretchy
and the effect is exactly the same
A crack appears under the tape but does not come to the surface
Red green orange can be used that is
It doesn't matter there
Now the second method of reinforcement when the mesh is embedded
directly into the plaster
In this method the mesh is not glued with adhesive but
simply attached to the wall before installing the guides
It is fixed in such a way that during plastering
work the mesh can be unfolded and plaster applied
On the wall then press the mesh into the plaster
and apply another layer of plaster on top
It turns out that the grid is located within the plaster
I apply a strip of plaster to the
wall under the mesh then embed the mesh
I apply plaster and install the screed
I secure the mesh with screws into the
foam joint between the wall and the ceiling
Reinforcing silicate blocks is not necessary
but somewhere I had to show you this method
What ultimately resulted
The grid is under the beacons
When I start plastering I just move the grid aside
I apply plaster to the wall and press the mesh into the plaster
And I apply a layer of plaster and smooth it out
That is the mesh is located within the body
of the mortar
You can place it in different ways you can just place
the strips under the beacons and glue pieces here
I did it this way so it can be
moved It's not important How to prepare
monolithic foundations and
Gypsum plaster on concrete panels
First of all all monolithic bases and concrete
The tiles need to be cleaned with a diamond cup
wheel to remove the cement milk and open the pores
Cement milk is a weak link and it is often
together with it that the concrete contact falls off
We did this procedure during the
dismantling stage because the work is dusty
Next the base is primed with a deep-penetrating primer
I'm foaming the gap between the ventilation ducts
After the foam has set it is trimmed and
the joint is reinforced with a mesh and adhesive
For improving the adhesion of plaster to a smooth monolithic surface
I use CERIZIT ST-19 concrete contact as the base
Before use the contents of the can need to be mixed I didn 't
have a mixer attachment for the screwdriver at my site
But I found a way I mix the concrete contact with a hex key
Concrete contact can be applied with a brush
roller or textured gun
I have a small area so I use a small roller
Concrete contact is applied in a thick
layer so that after drying a crust remains
One of the errors is rolling the concrete contact to zero
This results in a residue remaining on the wall after such rolling
Very little quartz sand namely
quartz sand holds the plaster
Pink acrylic filler is the binding element
Concrete contact dries in three hours but
I usually always try to apply it in advance
Don't make my mistake it's
better to put cardboard under the
wall first otherwise you'll have to clean the floor later
Once the concrete contact has dried you can proceed
Apply plaster and install beacons
The most important thing is that the plaster
is held by quartz sand not an acrylic filler
The video has ended if you liked it of course
Like subscribe to the channel and leave comments
Please make sure to click the bell and
wish everyone a good mood goodbye for now
