How to Plaster Interior Ceilings with Wooden Lath, Interior plaster ceilings remove and re-plaster

We Can
46 followers
2 Video Views·Nov 15, 2022
Hello folks, Kirk here with Kirk Giordano plastering. I'm going to show you folks today is
how we're going to repair this ceiling. We're in a stairwell, and it took us already three hours to
cover, bring all the scaffolding here, plank, cover, two layers of paper, tarps, and all you have to do
that. Otherwise, you'll be spending a lot more time to repair it. Hey, Dan, what's up buddy?
What we're doing now is I'm scoring this wall because I just spoke with a homeowner, and I said,
well, gee, the only thing we can salvage here is maybe this piece here, this one piece here,
maybe a two-foot section. My advice to them if we're going to go through all this work and set
all this up, three hours of just set time, let alone even start to remove this, take the whole
thing down. So that's what we're going to do, and I got three utility knives with me. I'll show you
because this is stucco. It's plastic, and the first blade I'm going to just tear up. We're
going to go through about ten blades utility knife blades. They're cheap. We put it here,
and we just keep going over and over until the whole blade goes in it. That's called scoring.
We are scoring this plaster, and when each time a blade gets gone, I just reach in and grab another
blade, and we score it over and over. So when we start removing it, it's going to stop right here.
Otherwise, the whole thing comes off. We're taking this piece here, there, this corner here,
right up to the wall here, right here, and we're scoring it again. We're going to do a lot of
utility, but that's okay. Now, once we remove the whole ceiling, then we're going to apply bonding
agent and re-plaster. I'll show you what I'm referring to now. There's a lot of ways to get
this ceiling off. I can hammer hatchets, trowels, you name it. I can take it off. No way is fun.
It's all a drag. If you don't like getting dirty, don't try to do this. Wear a mask goggles for the
sake of explaining it. I'm going to inhale some of this nasty dust. Okay, we're going to just
start it just like that and drop it on the floor because we have a hardwood floor. If I drop it
on the floor, it can dent the floor. In fact, the floor doesn't have some dents where this dropped
off by itself, so we're just going to go like this. It's going to take us a couple, maybe an hour.
We've got a couple of us and just make this whole thing on here, then put it in a bucket.
When we get to the stage where the entire plaster is off and we're putting plaster weld up there,
uh, it's made by Larson's. I'll show you that in our new new plaster is going to mushroom
through these, and even if it didn't catch all of it, the new bonding agent, uh, plaster weld
will adhere it, so when we get to that stage, we'll show you folks. Well, guys, this is some easy stuff.
If all of it came off this easy, man, there'd be nothing to this. It's just coming right off.
That means it's been wet for a lot of years. No wonder it fell off by itself. Usually, it'll
touch them up, and it's really tough to get off. This is just coming off in chunks,
throwing it right on the pipe so we don't damage the floor. Okay, that took us about an hour of
nasty work. Here's a tip. See, we want these, uh, um, the last we want these grooves. They're called
keys, and we want our new work to key in back of them. That's what mushrooms underneath some of
these that don't want to come out. Just tap them like this way. Now, fortunately, whoever did this,
they were real craftsmen, but when I was working union, that's how we used to do all our corners.
We put, um, there's 3.4 laps, so they got mesh here, mesh all around the perimeter, so I was
just taking my hatchet, tapping it like this pops right out. Beautiful guys that did this work this
stuff here. This is just, uh, plaster. Well, artisans makes it. There's a lot of their well
treats for exteriors, and then you use a lot of the pink stuff for the insides. Now, the idea is
there's dust on these, so what this is doing is not only removing the dust, but as far as I'm
concerned, it's giving it a bonding agent. We are going to bond right through these keys. However,
for the sake of really bonding well, when I do something like this, it's guaranteed for life,
so I want it to stick. I want it to stay on there, but we're at the stage now where, uh,
now that we've knocked it off, Jason's going to start mixing while I'm doing this. We're always
multitasking, and then I'll show you how we stick these two coats on. All right, guys, 20-minute mud
means it sets in 20 minutes. By the time I'm done with the first coat, I'll be able to put
my second coat. This stuff is, I mean, you can see you can play with this stuff. It's
real sticky. Take it off the front, the bottom, anyway, very sticky mud, very sticky mud. Okay,
we just scratch it right now. That's all I'm doing. I'm putting the first coat on.
We're going to take a lunch, and as soon as we're done with lunch, let's put the second coat on the
finish. That's a beautiful finish. It's adobe texture, real simple. If you know how to use
the tools well, and it's pretty hot in here, so it's setting back. It's probably 90 degrees,
95 up here because it's a hot day. We are in beautiful Orinda. All right, guys, second coat
going on. This didn't take me long because it's so hot right now up here. It's like
hot 100 degrees. I'm sweating. What we're going to do is finish this coat, then take lunch,
then I'm going to put a small coat right over just a real light one again. I'm using 20-minute
mud because where I get my mud west side building materials, they don't sell five-minute mud anymore.
When I asked him, how come, he said, you're the only one that likes that stuff.
When we work, we're in a hurry when we're doing this stuff. Anyhow, a couple more tips.
I took the door off. That door would be in my way constantly, so a good setup, a good cover,
take the door off, and my youngest son dad said, how the heck did you already get rid of that gallon
plaster? Well, a fat roller is like a $10 roller. It'll go through paint or anything,
no time. Just dip it in once. It holds a lot. All right, next time you see us,
I'll be putting that second coat in this adobe finish. All right, guys, we are putting the
second coat on the first coat set, and again, we're 20-minute mud, so that first coat actually
took about a half-hour to set. Why did it take a half-hour to set up this 20-minute mud? Because
I sealed all the wood lap with weld creep, so we technically had about 30 minutes before
it got like this hard. Now, this 20-minute mud is I get about 10 minutes. Why only 10 minutes
with 20-minute mud? I'll tell you why, because this is dry as a bone, and when I put this coat
on here, it's just sucking the moisture right out as fast as I put it on. It's sucking the
moisture out. This is called my brown coat only going about a quarter inch thick with this,
and in about, oh, I'd say 15 minutes. Then I'll show you how we do an adobe texture over,
and this doesn't have to be perfect because the adobe texture is very forgiving. It's a good word,
very forgiving, so even if I don't make it perfect, I can fix it with the texture.
All right, guys, we're doing the texture now. This texture is adobe, which once you got your
mud on it on the hawk, generally, fellas take it off like this, but you can't do that on this.
You got to take it off of the top. You put your trowel here, and you pull it off your top,
so the mud is in the middle of the trowel, and that's how we get an adobe pull it off
adobe. It gives a very distinctive finish as opposed to a skip trowel.
Very simple to do. It just takes some practice.
It looks a lot tougher than it is one of the more simple finishes adobe.
Anyhow, I'm going to go ahead and finish this up, and then we're going to clean up.
Uh, this fella emailed me two days ago. I looked at the email and said, gee, I can't really see
much, but he gave me some pretty accurate photographs, so I gave him a quote, and it
was a wee bit more than I thought, so we adjusted the price, but anyhow, you see what I'm doing.
We got the nasty trowel cleaning all this mess up now. This is the easy part. I've got five minutes,
and I'm done, so I'm going to leave it at that. My name is Kirk. I am with Kirk Giordano Plastering.
Thank you, folks, for watching. Hopefully, you learned how to do a ceiling repair
with an adobe finish. See you on the next one.
