Putty for painting. 3 layers and you're done! # 33

Pavel Sidorik. Renovation and Finishing
79 followers
95 Video Views·Dec 11, 2022
Hello friends everyone
Pavel Sidorik with you as always and this is a channel about repairs and renovation
and decoration
In this video I continue
preparing the ceiling wall for
painting There is a lot of information so in the end I
Three videos were made
The link to the first video will be in the description and in the pinned
comment
Now let's go through everything in order
I will smooth the ceiling crack from the scaffolding as I
feel more confident with the trowel and have better control
It works out
Apply in the same way as on the walls
The only difference is that on the ceiling the first layer
I apply the filler in parts so that I can
smooth it out with a trowel before it sets
Immediately you need to remove
the spray that got on the walls Later I
will show you a way to get rid of the spray
Mechanical application is certainly much faster
than manual and results in a higher quality because
A trowel is long and levels the surface further
It took half an hour to paint the entire ceiling
What are the rules for smoothing compound
when applying it by mechanical means
First especially the trowel and
which one there is a stiffening
edge If you look at it like
this you can see that it is almost flat
This side is the working side it is the stiffening edge
meaning you cannot smooth the filler with the other side
Only one side is being smoothed
Second point
Angle of attack
What is the angle of attack
The angle of attack
is the angle at which you apply the filler
You can't smooth it like this in
one place and like
that in another You will just end up with different layers
Therefore the angle of attack should be approximately the same
across the entire wall to ensure the plaster is applied evenly
If the wall is slightly crooked somewhere
the large blade helps to straighten it out
There are no rules for
dry to wet here Why Because
the entire wall gets splattered with spackle
Usually the first layer for example the first part is stretched
from the floor to the middle the second part is stretched
From the ceiling to the middle
If your wall is 4 meters or more the
same can be done using an extension
Apply half from the top and half from the bottom
I applied the filler starting for example from the bottom
Pulled it halfway down gently removed it
moved on to the next layer
If there are any remaining transitions you can ignore them
If there are excess the filler is simply removed with a trowel
It's extra in the bucket
Then pull the bottom go up exactly the same from the top
You pull it to the middle and then smoothly
take the trowel The next one the
next one from the corner
That's basically all the rules you'll feel it over time
this trowel
They find it much easier to apply the compound than
with a regular one because there is no strain on the brushes
This is a large pen the trowel is made of aluminum and
light and with such a trowel it is very convenient to work
If you are just starting with mechanized drywall
finishing which trowels should you choose
I have a complete set of Oleynik spatulas
Blades 0.5 mm and several spatulas
where the blade thickness is 0.3 mm
0.3 mm - these trowels are designed for smoothing
finish coatings more liquid ready-to-use finishes tha
Lay down a thinner layer the 0.5 blade is intended for that
For applying the first layers including with this blade
Smooth the finishing putty
Most finishers use trowels with a 0.5 blade
because it is stiffer and therefore additionally
It also levels the wall
The most popular trowels are 80 and 60 cm
These little ones are like auxiliary but not
exactly auxiliary you can buy them or you ca
Don't buy them Why do they even make such small
ones Because when you apply
the filler you have a certain amount
angle of attack
And so that this angle of attack is the same on all
surfaces for example you are fairing some narrow
A small strip but in principle they made the same
trowels so that the putty is applied the same way
But again I'll say that in principle you don't need
to buy them you can just use regular putty knives
Not with such a brush but just ordinary ones
But these putty knives are the most popular
You can smooth the filler with an extender
This extender is usually used for smoothing the filler
On the ceiling but again many finishers smooth the
compound just with a trowel without using an extender
So you have to try and see if you like it or
not The main feature of these trowels is
that they have replaceable blades
Blades
After the filler has dried it needs to be sanded
For wall sanding I will use an orbital sander
The DLT-KS01-15050 machine
I've already used it and it has performed very well
150 is the wheel diameter 5 mm offset brushless
The engine the machine
is very light
electronic shifting and electronic engagement also connects to the vacuum cleaner
During sanding there is almost no dust the machine is stable
and does not jump it runs very smoothly most importantly
It's quiet
I like to sand such a machine
you know much more than a giraffe
Because you feel the wall the machine and you can
carefully polish everything even almost perfectly
I approached
her from the corners without grid interference and the platform itself
The price is small it's about around 200 dollars
the link to this machine will be in the description
By the way DLT store ships equipment including
to Russia
I recommend it it's a great thing
Polishing machines make it much easier to sand walls and
ceilings hands get less tired and the surface
quality is better
I'm cleaning under the
lamp so all the unevenness and bumps are visible
If you are using a vacuum cleaner there is almost no dust
The most important thing when preparing the first layer is
to make a suitable surface for the final ready-made compound
I will explain the details about the cleaning
rules during the finishing layer sanding stage
After cleaning the base must be dusted
We clean the base with a vacuum in my
opinion this is the most effective way
Note that we are all working under the light
of the projector
With the light all the dust on the wall that needs to be cleaned is visible
Remove from the vacuum
We applied the first layer of putty to the
walls and ceiling sanded it and dusted it
We will prime the walls and then apply two
layers of ready-made finishing compound
Honestly I don't see the point in applying two layers of dry
polymer filler LER Plus why because the wall
was previously prepared the plaster was sanded
It was already a flat surface With
this one layer we filled all the
pores and now we have a good base for the final ready-made filler
These scratches don't show it's all one
plane it will all be covered with two layers
Finish filler
Next apply the primer
We will apply the primer using the spray method without an air compressor
It takes literally 10 minutes to prime the entire room
The main thing is to control leaks using a lamp
If they suddenly appear I immediately roll them out with a roller
We primed the wall and ceiling yesterday and left it overnight
It has dried and today we will apply the
finishing compound to the walls and ceiling
I run my hand along the wall my hand completely clean
Today we will try to apply two layers to all surfaces
The ceiling and walls and the room will already be ready
It will only remain to clean and prime it
I will apply the final putty using
side lighting This
is Losyev's lamp
If the wall is already prepared for this lamp then for a regular one it
will just be perfect Because this
lamp illuminates all the imperfections
Completely
The lamp illuminates the entire wall and when applying filler
you can immediately eliminate all defects
Many finishers criticize Losiev's lamp for revealing
all the unevenness and defects
on the wall too clearly
What is not visible under an ordinary lamp is visible under a Lesev lamp
This is precisely why I do not use this lamp for
Acceptance of work
I only use it to speed up work processes
because it's really convenient to do everything under it
If you already make the surface for this lamp
nothing will be visible under regular light
So if a customer comes to me for a property
inspection with such a lamp I'll probably send him away
Because there are no developing light lamps in
any SNIPs anywhere For questions regarding
the operation of this lamp
First there is a plastic sheet here If you
scratch it with a spatula it gets scratched
Manufacturers do not use regular glass here
because if the lamp falls regular glass will break
And this is the armored film for these purposes
You apply the film here as soon as it is worn out
It gets scratched you peel it off and apply the next one
There one or two should be enough for the job
There were also questions about the lamp's handle
Because of the narrow opening when it is inserted
A thick-shafted holder which sometimes broke
But the manufacturer has these hexagonal handles
where you can adjust the thickness of the holder
I slightly dilute the finishing compound with water
I added about 0.5 liters of water to the bucket
Apply thick putty carefully
I mix everything immediately in the bucket with a mixer
I am applying the filler to the device system
I am flushing water out
of the hose until the putty comes out
For the final putty I use the 531 nozzle
By the way the nozzle holder for painting and puttying
The same only the nozzle changes
The hydraulic powder applicator applies the filler like paint
The flame is sharp and therefore nothing needs to be sealed
The flame reaches the ceiling and floor but it's not critical
I apply the final putty in sections
taking about 1.5 meters of the wall
It's better not to rush or you might not have time to smooth the filler
This is what the applied wall filler looks like
Smooth the filler starting from the corners First
I took a 60 cm trowel on the next wall already
used 80 cm
I pull the bottom half of the
wall and the top half I pull from above
I apply the filler to the next section
of the wall with a slight overlap
The trowel technique is the same the first half from
the bottom the second from the top
The hands remembered the work and the
applied layer was now becoming more careful
Excess plaster that was scraped off the wall is thrown into the bucket
Ready-made finishing compound in buckets allows for easy applicatio
Second layer applied wet-on-wet that is you applied the first one
The layer was literally dry after about 30 minutes an hour and
the filler became matte so you can already apply the second layer
What does this give us First of all it significantly speeds up the workflow
Secondly the first layer does not draw water
from the second
The second layer is the finishing one so you
need to pay close attention to avoid any gaps
If the second layer of filler
is applied too early scratches
may occur I applied the second layer about an hour later
The application technology for
the first and second layers is the same
After applying the filler we clean the
adjacent walls and ceiling of the spray
In general there
are various methods to protect walls and ceilings from peeling
Someone is inserting a card someone is scraping it off
You can apply masking
tape around the perimeter to protect the corner
The painter's tape I
use has been in my possession It's Blue Dolphin It's more expensive
but suitable for this job
The cheapest painter's tape
Apply the tape in two layers
around the perimeter of the wall being plastered
This method is very suitable for the reverse application
technique When you apply the masking
tape just unwind it like this
From the roll and immediately pressing it against the wall
Thus the painter's tape is pressed
against the corner and very carefully
Lean this plane against the wall and twist it
Push it back and press it against the wall
You can make a small opening and
then just press it with your finger
They made a small batch pressed it with their finger
It is best to apply putty to walls that are parallel
to each other so that the corners do not intersect
While the filler is still fresh
The mechanical method of applying putty allows for better
results The wall becomes
smoother with fewer imperfections
ransitions
It takes about 20 to 30 minutes per wall
The filler gun is in another
room and thanks to
the long hose it can be used anywhere in the apartment
Although I don't have much experience with mechanical
spackling I've already gotten used to it on the second wall
Everything was working out much faster
I'll explain why I don't use a glass fiber and apply
only three layers of filler in the next episode
You can sand the entire apartment in
one day with the help of an assistant
Three layers are applied for
preparing the walls for painting
One layer of dry polymer filler and two layers of ready-made
Finishing compound This is enough to make the wall
suitable for
high-quality painting
I remove and throw away the tape after applying it
Most of the coating remained on the tape
Continuation to follow
