Next on this 1979 Bally Supersonic we've been repairing we need to try and save the playfield.
Check Out Our Patreon Account, for Unreleased Repair FAILS, Concise Repair Tips Not Possible In This Long Form Video, And 1 on 1 Repair Assistance with YOUR Project!
Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
Ladies and gentlemen, this is Joe's
Classic Video Games back with another
cool pinball repair video for you this
evening. We have been working on this
Bali Supersonic that's in really rough
shape. And uh unbeknownst to us, when we
bought it, the board, two of the boards
were missing out of it. And then one of
the other boards had a short on it that
fried all of the remaining boards in the
game. So, we've been doing several
videos where we go through each board
and fix it. And so, we've actually got
it up and running again now. Um, but one
of the other problems with the game is
there's horrible playfield wear on it.
This isn't the worst I've seen, but it's
pretty bad. Look at this.
So, in this video, we're going to see if
we can take care of a little bit of
this. Um, now there's different ways you
can handle it. And this is this one's
really pretty rough. I'll show you
details here in a second, but um,
there's different ways you can handle
it. One of the better ways is you can
put a hard top on it. Um, which is you
take everything off the playfield and
then there is a product that they make
called a hard top. Hard top that is
basically a big piece of plastic
essentially that you put over the uh
playfield and it makes everything just
like new again kind of. But they, you
know, they they play a little different.
They're kind of expensive. It's a lot of
work getting the playfield properly
prepared for the hard top.
And then when you're done, you you know
you it's not really the same. So, I'm
not against those or anything, but I
just choose not to use those usually.
But that's one way of doing it. And they
look pretty good when they're done. That
might be the way you want to go. That's
not the way I want to go. Um, another
way that you can do it is they make an
overlay, which is like a sticker. That's
a similar concept. We don't like those
that much either. You can kind of tell
it's a sticker.
Um, the way we do it is we clean them
off as best we can and then repaint it
and then clear coat it. So, that's the
way we're going to do it. So, the first
thing I need to do is take all of the
stuff off the playfield or most of the
stuff off the playfield that's in the
way. Uh, so we can properly clean it and
then we can see just how bad the wear is
once we get that off. Um,
some of the areas
the paint is actually
still flaking away.
Like here, I'll show you.
Some of that is still coming off. Here's
a good example.
Look at that. Look at that.
I had somebody criticize me on a
previous video
because I was making the point that it's
already damaged. It just needs to be
removed, right? And he's like, "No, it's
not. You're ruining it. There's
techniques to save that." No, there is
not, folks. There is no technique to
save that. Whenever it's flaking up like
that, it's done.
It's not clean. It needs to be cleaned.
And then there's no product, no special
method that's going to make that lay
back down flat and adhere to the to the
playfield anymore. It's done. Like our
buddy Shango, and I don't know Shango,
but you know, I feel like he's our
friend, right? Our buddy Shango would
say, it's baked.
Look at this
baked.
So, this, like I said, this one is
significantly bad.
So, all of that to say,
we're going to have to clean this up
because you've got to get rid of
everything like that that's going to
flake off um
and get down to a nice starting point,
which means we're actually going to lose
more paint than we have right now. Um
I'm not too worried about it, though,
because um um there's really no art on
it. It's all just geometric shapes. So,
we'll see. Now, this is not going to end
up being a 10 restoration. I'm not
capable of that. I think it'll probably
end up being a seven or maybe an eight
if we get lucky. So, that's where we're
going. So, let's take all the stuff off
the playfield first and then we'll go
from there.
[Music]
[Music]
Everything's
[Music]
All right, folks. This is how it ended
up looking with all the stuff off.
Pretty rough. We haven't cleaned it,
obviously.
Next step, we need to clean it.
I hate losing the parts that actually
have text on them. That's the hardest
part to get the lettering back. But, you
know, parts of it like that are already
worn away anyway.
So, we'll make it happen. Where? There
was one that looked like it was going to
be real pain to put back. Where was
that?
[Music]
This a little bit because it's one color
and then outlined, but it'll be all
right.
All right. Yep. So, that's what we're
starting with. So, I'm going to get the
vacuum and I've got a little brush
attachment on the vacuum where I can
kind of rub it a little bit and get some
of this flaking paint to go off. Now,
some of it like this.
If that holds on, we're going to leave
it.
Yeah. So, that'll probably clean. Um, so
that's next step. Just going to vacuum
it. Oh, we're going to lose a lot of
this when we do that.
But it's, you know, it I Yeah, the
thing's destroyed, but a lot of it
isn't. A lot of it's just fine. Like,
it's nice and solid. Um, the paint's
just not. And uh if you if you don't
know, if you haven't watched us do this
before,
what happens is this paint and even the
wood under the paint cracks and then the
ball gets like a little tiny bit of a
like a a little rust spot or something
and then as it rolls across the paint on
the playfield, it eats it alive. It's
like sandpaper. So if you look close at
the paint, you can see see all the
little round marks. They call those ball
swirls.
That's just where some little defect on
the ball
has just rolled around and caused all
that on the playfield.
So, if you look at a place where the
ball never really goes,
like we'll say right here,
you don't see as much of it. There's a
little bit, I guess.
Let's see. So,
so this see this little wear line? The
ball cannot physically go past that. So
if we're anywhere near this little black
line, the ball has never touched that.
So we went too far, folks. Let's go
back.
So see how you don't see the swirl
marks?
You just see the cracks. The cracks are
the pl the plywood underneath the paint.
It's wood, you know.
So, it's not really a even a paint
defect. It's a wood defect.
And if you go, you know, if you go up
just a little bit to where the ball
actually does
hit it, you see all the swirls.
So, that's what we're dealing with.
Vacuum.
All right. So, I vacuumed it all out.
get rid of the extra stuff.
This is what's left up here.
But all of that's on there pretty good.
Um, I popped the apron off. This has
damage on it I have never seen before.
Look at this.
I don't know if that's a defect in the
playfield or if that's where somebody
did something from underneath.
That's pretty wild. doesn't really
affect the gameplay though. So, um, so
yes, we're starting with a pretty ratty
one. Okay, so the next step is we got to
clean this thing up as best we can
because we're going to paint over it and
we're going to clear over the paint. The
one of the reasons we never show anybody
how to clear is because it there's a
professional way to clear or a couple
professional ways to clear and then
there's kind of the hobbyist way to
clear. So, we're doing kind of the
hobbyest way to clear because we're
doing it here in our storefront.
I mean, we're inside a building
obviously and I can't go outside and do
it um because it's just the sidewalk,
you know. Sometimes we go out back and
we'll spray paint like some pinball eggs
or something, but
the to do this like professional, even
if I had the ability to do it, um the
skill to do it, I can't really do that
outside on the sidewalk behind my
building. So, we just do it here in our
shop, which means that if you you know,
we're using a spray paint can inside.
It's not really optimal, right? But the
way we do it, we clean it all up. And
I'll show you here in a second. We clean
it all up and then we hand paint it and
then we clear it with just rattle can
spray paint. Just, you know, we usually
use satin. It just kind of blends in the
most. This is kind of a satin finish.
Um the newer playfields, it's more
glossy, but these things are old. I
don't think they were ever glossy.
That's the original finish there. That's
your sheen, right? Um, so we do satin
and then we wax it. Now, there's
different levels of clear. The
professional way is you would use a like
a two a um a clear with a different
catalyst. They have this new stuff for
uh car that people are using for car
paint that uh is like spray max spray
2000 and all that. The two the two in
that means that it's two- stage. There's
there's um basically you have to mix two
things together. If you buy just a
regular rattle can Kryon spray paint,
which is what we use um because of our
circumstances here um and other reasons,
but um it it is formulated one way and
it's not as hard as what would have
originally been on the playfield or what
the two-stage uh the Sprayax 2000 for
instance would be or automotive clear
coat. So, what some people will do is
they'll do their touch-ups or whatever
and then they'll take it to a car paint
place and talk them into spraying clear
over it. That's a really good option if
you if you want to go all that through
all that trouble. Uh it's a it's a
little bit fraught with danger, though,
because if you if you do the touch-ups,
I don't really want to be moving this
thing around after I've done the
touch-ups if I haven't put clear on it
because I'm touching it up with acrylic
paint, um which is water-based paint.
So, the way we do it, the easiest way to
do it, the cheapest way to do it is you
paint it back by hand with acrylic paint
and then you just spray over it with
rattle cans. Now, the reason we don't
show that is because I don't want to
encourage people to do that. There's
nothing wrong with me doing it the way
I'm doing it, but if you have, let's say
you've got a pinball machine,
everything's cool, and there's a little
little bit of wear somewhere. Let's see
if this baby Pac-Man has any wear on it.
Yeah. So, like right there in front of
the
of the bumper. So, let's say you touch
that up a little bit and then you spray
clear on it, you're going to screw up
that whole area of the playfield. You
can't do it like that. The problem that
you have is if if the playfield is not
completely clean
when you spray that clear on it, it's
going to fisheye. It's going to bubble
up. You're it's you're going to have a
texture on it. It's going to have orange
pill. If there's any kind of contaminant
in the paint on the playfield at all,
it's going to make a big mess. So, I
don't I don't really want people doing
that just trying to touch stuff up. Now,
if you're doing the whole thing like
we're doing it, I'm about to scrub it
with a magic eraser. That's going to
take off any kind of wax that's on it.
That's another thing. A lot of
playfields have been waxed. They're
supposed to be waxed, right? The older
ones. Um, so you can't put clear coat
over a wax. you're just going to make it
the biggest freaking mess ever, right?
So, you've really got to clean things
up. Um, you can use Napa. I've never
really used it, but it's it it will get
rid of contaminants and stuff. So,
there's you got to do a lot of prep work
to pull that off. That's just my whole
point and that's what we're doing. So, I
don't I don't really want to show people
how to screw up their playfield by
spraying rattle can $4 I guess it's $8
now. eight dollar uh clear coat on it
without properly preparing everything.
But that's how we do it. So, um I'm
gonna get a magic eraser and I'm gonna
use we just use Windex, which is
basically soapy water, you know, um
uh on the playfield. Now, you can use a
magic eraser and um
uh rubbing alcohol or isopropyl alcohol,
but the the deal with that is that stuff
is strong. it will cut this paint right
the hell off of here. So, what we like
to do, spray it down with Windex, which
is just water with a little bit of soap
in it and ammonia in it. Um, and then
use the magic eraser on it. The ma the
magic eraser, the reason it works is
because it has little tiny particles.
That foam is is very uh uh just the
composition of it is little tiny
particles. So, it will get in all of
those cracks we were just showing. Like
all these little ball swirls are little
cracks in the wood. That foam is so
small it will get in that, right? And it
doesn't magic eraser is just the the the
common name for it. It's actually I
think it's called melamine foam or
something like that. Um so if you if you
get the generic stuff off eBay, it's the
same exact thing. It's just a byproduct.
It's a type of foam, right? Um, so that
will clean it up really well, but it's
basically sandpaper. So, you're using
very fine sandpaper
to clean up all of the mess on the
playfield. This one is obviously an
extreme example. I would say that this
is a
one to 10. This is a I guess it's a two
because I've seen worse, but it's a two.
You know what I mean? It's a freaking
two. Now, it's wood, so technically
you're not supposed to use any kind of
water-based thing on it because it will
do things like
like this. It will cause problems. But
here's the problem. This thing's
destroyed. It's a two. We're not going
to make it much worse no matter what we
do to it. Look at this line all the way
down the playfield where the playfield
is actually cracked, right? Where that
ply is cracked on it. So, yeah, I'm
going to use a water-based product on it
because it's so extreme. I've got to
clean it up
and it's going to be just fine. We do it
all the time. No big deal. Um, now if
you had a nice playfield, everything's
in good shape. You wouldn't want to do
that. You could you can clean very well
with wax, which is, you know, petroleum
based. So, if you put a if you put or I
guess it is, is is carnuba wax petroleum
based? I suppose it is. Um,
yeah, it's oil based, we'll say. Um, if
you if you've got a pretty nice
playfield that's got a nice surface on
it, you can clean it up pretty good with
actual wax. Wax is actually a cleaner,
not just a something that makes
something shiny, right? Um, so game
plan, we're going to use Magic Eraser
and Windex to clean it all up as best we
can because any part that we don't
repaint, like if I don't repaint this,
and we might end up repainting
everything. This yellow here, we
probably won't repaint. So any any part
that we don't repaint, we want to be as
clean as possible. So we're going to use
a magic eraser and Windex to get that as
nice as possible and then we'll go from
there. Um after we get it all cleaned
up, we're going to start drawing the
missing art back in. And then we're
going to paint by numbers, basically all
the areas. When we're done, we're going
to put the lines back on top of uh the
art and we're going to uh put the
lettering back, which is actually the
hardest part. it never looks right. You
can do water slide decals and stuff like
that for the lettering instead of hand
painting it. Um I just don't I don't
mess with that too much. If you do a
water slide decal,
you end up where you have a problem
where it's it's at a different height
than the paint next to it. Clear coat
will fix that, but you really need to
clear it, sand it, clear it, and sand
it. We don't do all that. It's just to
to properly restore this would take I
literally you could spend 80undred
hours working on this playfield. We're
not going to do that. We're going to try
to spend six or seven hours working on
this playfield
and turn our two into a seven. So that's
our goal, right? All right. So first
thing we got to clean it up with Magic
Eraser. So let's get at it.
[Music]
[Music]
[Music]
[Music]
Okay. So, I tried to show as much of
that as I could so you could just see
how we do it. Now, when you're done,
kind of the my favorite part of the
whole thing happens. Um, because it
leaves this film all over it. And so,
the film is like dirty Windex and pieces
of the foam and all that. So, like if
you look here, it's all kind of dirty
looking actually
because that's the the liquid was wet,
you know? I mean, uh dirty. Um I had
some some of those little uh some of
those melamine pads were real thin. You
saw them all breaking up. If they're the
don't get the thin ones, they just don't
last very long at all. So, I probably
went through about five of them, the
fulls size ones. Okay. Um, so
my this is my favorite part because we
have to get rid of all this mess now. So
you just spray it down and wipe it off.
And as you do that, you're going to see
whatever's left, right? And it's going
to for a second there while it's still
wet, it's going to look basically as
good as it can possibly look. So it's
going to look how it's going to look
whenever you wax it. Now, obviously,
this one's in horrible shape, so we're
only going to see it in a few places.
But another thing I wanted to point out
was when you use the magic eraser,
you're not going to get rid of all the
wear. So if you get close enough, I got
the yellow looks a lot better now. But
if you get close enough,
look at that. All of that is still there
and it's going to stay there. I can't
get it any farther down. Basically,
we're sanding through the paint. And
like I was saying, it gets down in those
little cracks, but only so far and only
so many of them. So it's not a perfect
thing. Now, if you keep rubbing on it,
you're going to see more and more of the
white popping through because there's
like a white primer basically underneath
all of the artwork. You can see it
popping out everywhere. So, you don't
see you don't see wood grain there. You
see white.
It's like a primer basically. It's the
the first coat that's silk screened on,
I guess. Um, so it once you start on
that, you're going to just get more and
more of that white coming through and
eventually you'll start losing. You
know, if you look here too, this is
pretty heavy wear. See around the edges
the white.
We also have the problem where there is
a
there's now a a level difference. It's
not smooth. The wood is lower than the
paint. The paint has a thickness to it.
So that ends up being a problem, too.
But the thing that you have going for
you is even with the wear right up here
at front when you play it, you're about
right here. You're kind of a little bit
aways from it. Just your your eyeballs
physically are a little bit away from
it. So if you get it decent enough, when
somebody walks up that's not, you know,
an expert on pinball, they're not even
going to notice the touch-ups. So that's
what we'll try on this. I don't know how
good we'll get. This text right here is
kind of worrying me. I might just not
even do it, but we'll see. It'll be at
the end anyway.
Okay, we'll practice over here and then
if we can do that, we'll do that.
All right, so uh the next thing is we're
just going to spray it and wipe it all
down and then that will be about as
clean as we can possibly get it and
it'll be time to start doing some of the
paint.
[Music]
Heat. Heat. N.
[Music]
Heat. Heat.
[Music]
[Music]
Heat. Heat.
[Music]
All right. So, I just wanted to clean up
that hole a little bit just because it
looks like crap. Um, okay. So, obviously
you can go as far as you want on this.
Like you could take everything off. You
could take that little platform
underneath the hole out and clean it
better than I just did. You could take
this apart and clean it. You can take
all these off and clean it. So, it's
just how much time do you want to do you
want toh invest in it? Now, we have a
shop. We're reselling it, you know? So,
like I mentioned before, I can't work on
it for 80 hours and make any money.
It'll never happen. It just And this
thing is beat, you know. So, it's this
isn't going to be worth a whole bunch of
money when we're finished. So, all I all
that I can afford to do to it as a
business is, you know, fairly quick and
dirty. But, I'm just trying to give you
the idea of what to do with yours. So,
you can take yours farther than that if
you'd like. But, I feel confident that
we've got it nice and clean. Um, I will
say though,
see how clean the wood here looks? The
the the bear area. And then if you
rewind to the beginning of the video, it
almost looked that clean before. So
somebody has already worked through this
thing at one point. Um because when they
wear they get really dirty. So that
would have been black basically. You
would you would have been been seeing
dark brown black wood. Um so somebody
has already cleaned it up. Maybe they
were going to uh repair it. They worked
on the playfield a little bit and then
they had that little boo boo with the
MPU where they shorted the pins together
and burnt up every single board in the
game
and uh they they decided
uh to hell with the cheese let me out of
the trap. So, who knows? Um but yeah, so
I feel comfortable that we've got it all
as clean as we really need to have it.
Um
another thing you could do is take the
pop bumpers off. uh you know more of the
rails off these rails off but for the
way we do it it's not necessary. So our
next step would be to ink in the lines.
Um once you do that start do with the
color like color by paint by numbers
basically. Um and then once you do that
stencil in the artwork but this is a
good uh first step. So I wanted to do a
video showing you how we prepare the
thing.
um and just kind of talk about it step
by step how we go through it and why we
do it that way. So I hope that
was interesting to you. So you know what
is next? I have to start inking it in.
However, we'll put that on a different
video because it's getting late. So
we'll see you next time. I hope you've
enjoyed it. Now if you I I'll put the
link to the next video up on this after
the next video is up. So it'll be a
couple days. But if you're watching this
in the interim before that next video
goes up, this is not uh the first BI
that we've repainted uh that had heavy
wear. We've done it before. Check this
classic out. We'll see you on the next
video.