Trying To Fix This Old Eskimo Electric Desk Fan...

Amateur Repair Time
257 followers
688 Video Views·Jan 19, 2026
Check out our Patreon page, for all of our channels. Contains outakes, concise arcade repair tips, bloopers, repair FAILS, Audio youtube wouldn't allow us to upload, and much more!
https://patreon.com/JoesClassicVideoGames
------------------------------------------------------------------------------------
AI Generated·May contain errors
Ladies and gentlemen, welcome back to Amateur Repair Time.
Look at this little beauty I picked up today.
I'm looking at, I'm working on two videos at the same time, so I'm also doing a
phonograph video, but look at, look at this fan. I was at the flea market today.
This fan was sitting on the table. None of these fools had bought it yet,
so it just sat there waiting for me. I asked the guy how much he wanted for his cool little fan,
and he said, well, I don't know, man. Just make me an offer, and then he was like,
how's five dollars? I said, you know what? I think I'll do five dollars. Now, I know what
some of you are saying. You would offer them three, but I don't do that crap. If it's cheap,
cheap, I'll just go ahead and get it, so I think we're going to try to fix it,
and then the guy, the guy was real cool because I picked it up. Obviously, it doesn't work,
right, because if you, the blades barely move, right, so I pick it up. I hand him the five
dollars, and the guy says, I don't know a thing about it, which you know what that means.
That means he plugged it in, and it didn't work. He just wanted to make sure that I knew
that he's not saying that it works, so he said, I don't know a thing about it.
I think that's actually a very honest way to put it. You know, he could have said,
now it don't work. I plugged it in, and it don't work, but the best he could do was that. Now,
I don't know a thing about it. Let's see. Looks like the back of it might be dangerous as hell,
but I guess it's made that way. You could easily put your finger right here in the back and get
it chopped off, so this is a little El Cheapo, but you know the El Cheapos back in the day were
better than the El Cheapos now. It's an Eskimo. You can barely tell. I hate we're going to lose
that label, so I guess I should document it. McGregor W. Edison Company, and I can't tell
what that says. I would imagine they're all. I'd love to be able to read the model number though.
Can we zoom even more? We can. That's a Burstead Manufacturing Division, Booneville, Missouri.
115 volt. There we go. That's a little better, huh? 115 volt, 60 cycle. Well, you know,
that's good because that's what I have coming out of the wall in my house. My house is wired
115 volt, 60 cycle AC. It's a model C81002 is the best I can tell. 30 watt, is that what it says?
I guess that's saying 30 watt, which would be like a third of an amp, and it's UL listed,
so I'm going to guess 50s. What do you think? Would it be UL listed if it was from the 40s?
I think they made these as far back as the 40s. It's such a small little fan.
Here's my hand. I would guess it's, I don't know, damn near two feet tall. No.
Oh, I guess I can't measure it now. It's not the largest version of it,
so I figured we'd take it all apart since there's not much there, and then I might sand it down a
little bit and paint it. I think most of these were this aqua color, so I'll probably go back
with that, I guess. It'd be cool to just paint it some cool color like purple or something, but
it's trademark was that most of them were aqua, so I'll probably get something that's
pretty close to that color if I do paint it. This is pretty much seized up. You can turn it,
and it hits the grill or the guard, and it's just, it's pretty banged up, right?
But even when it's not hitting the guard, it doesn't, it's not doing great. And then also,
if you notice when I turn it, so like this blade right now, so it's hitting over here. This blade
is not hitting. One, two blades, three blades, and then that one hits, and I don't know that
it's because the blade is bent. I guess it, well, maybe it is. Yeah, maybe the blade's just bent.
It almost looks like the shaft might be bent, so I don't know. We'll have to mess with that.
So, I guess the first step is to take it apart. So, there's a screw here.
I would imagine, yep, screw there. Just a little bolt there, and that's pretty much it. I guess,
I guess we'll have to take the guard off and then see if we can get the fan off and all that.
So, yeah, let me disassemble it a little bit, and we'll see what we're working with.
There have been successes, and there have been failures.
So, I got it apart. Check out these cool little tools I picked up a while back.
It's like a little set with a clamp. Clip tight set. Industrial Manufacturing Corporation,
Chicago. Pretty cool. Select steel. Okay, yeah, so it's so rusted, obviously. So,
when I went to take this off, two of these were already broke, and then the other two broke when
I tried to take them off, but it came off. We'll fix that. We'll figure it out, and then I had to
keep tapping on this. Tap, tap, tap, tap, tap, tap, tap, tap, tap to knock all the rust out that
was stuck inside of it so that the cap would come off. I took the cord. I'm going to replace the
cord. So, I just took it loose from the two kept nuts, and here's what we're left with so far.
There's a little cap right there that I need to get off so that I can try to take the nut off,
but the problem is these nuts, you know, when I went to take them off, that's when the
wire broke for the thing. It's pretty rusted. So, I really don't want to break the bolt
on the rotor. That would suck, but with that said, the winding looks pretty good, I think.
So, I think we're going to be all right there. All right, so I'm going to see what I can do.
You know, you can soak it and stuff, but I don't want to with that fan on there. It's kind of
a big pain to do that, so I'm trying to figure out the best way to do it. So, I'm going to see
if I can carefully remove it. I guess I could put some PB Blaster on it. You know, that stuff's
really good. The fan would fall off and hit me in the foot if I sprayed PB Blaster on it,
so I might have to do that, but that's next. Okay, I got it. It took about 30 minutes,
but I got it. So, here is the bottom bearing. It is locked up. I broke one of the screws in half,
taking the nut off, but that's a very simple, normal screw. I can literally go buy at the
hardware store, so that's no big deal. We'll put all new screws on it when we go back.
I got the rotor out, but part of the bearing came out with it too. This is, I guess,
completely seized up. It goes inside there, but I think I should be able to put it back in and
oil the crap out of it, or it may be made like that. Maybe it's press fit on here or something,
but you would think that it would be supposed to spin on here and spin in there. It just makes it,
you know, yeah, that would be a lot better. So, that was probably, that front bearing being
seized was probably why I had so much trouble turning it by hand, because I was turning
the rotor and the bearing inside of it. And then, of course, this back bearing being off like that,
you know, I'm sure that wasn't helping. It's the tail piece. We looked at that,
and here is the front piece. There was a lot of rust in there. It took quite a bit to get that out.
That's what took the 30 minutes. I won't tell you how I did it. Some of you don't know the ways
of the world. Some of you, some of you are going to get squeamish if I was to tell you how I did
it. You'd swear up and down that's not the way to do it. Okay, so this is the top. This is the part
that was inside the nose cone or whatever. You can see the winding's still intact. We'll check
it with a meter here in a minute. It's all pretty rusty, but I think it'll be all right.
Needs to be cleaned up for sure. I gotta tell you though, I'm squeamish about putting this
in the ultrasonic cleaner. I think I'm just going to clean it by hand, which mainly will be getting
the dust off of it and hitting it with a little sandpaper on the edges so it slides into the cone
easier. Yeah, so we'll see about that. Various bolts and stuff. I mean really though, there's
only three screws in the whole, well four screws count in the small ones. No, five screws count
in the small ones. Some 3.8 nuts. Here's the one that broke off. Strangely, after this one broke
off, the one that was below it, I could just take right off, no problem. More cool tool stuff.
Look at these. I think I showed these before. I have a set of Nappa nut drivers and they're the
good ones with the hollow shaft so you can slide it down over a screw to get to a nut. So if you
have like a screw with a nut way down on the end, when you slide the nut driver over it, the piece
that's sticking above the nut can go inside the shaft of the nut driver. Klein makes these now,
a similar product. Okay, and there was a little mud daubers nest or hornets nest or whatever that
is, wasp nest. The nose cone just kind of clips on. This would have been like a really cheap fan
back in the day. But like I said, time has changed. The world has turned and what was once
cheap is now what we wish we had. Okay, so just as a test, I've got some ZEP in my ultrasonic cleaner.
I'm going to go drop this in the ultrasonic cleaner and see if it'll do anything with this
rust. I'm hoping it'll just at least clean it up where it doesn't look rusty. Maybe it just looks
pitted or something. I'm not going to re-chrome anything or anything like that. I'm not going to
repaint this either because I think it would look kind of janky having the grill painted.
I would rather it just look old. But I probably am going to spray paint this because it'd just
be so easy. So I think what I'll do is I'm going to put that in there and run it for a little bit
and just see if it'll clean that up. I don't know if that it will. I'm not going to put this in
there. I am going to run the rotor through because there's nothing on the rotor that can get
screwed up. All that can happen is it get cleaned up and it might actually free this bearing.
I don't know. We'll see about the bearing. So yeah, I'm just going to try cleaning a couple
pieces first and we'll see how they come out. So there's the rotor and there's the fan shield
and it's bad. So let's just do the first ring. This is what the condition that it's in starting
out. You've all seen it before. It's rough. I don't expect it to make it chrome again. Of course
it won't. All the chrome's gone. But it might clean it where it looks presentable. And it may
actually leave that logo, which is so faded you can barely read it. But we'll see. Okay,
so I dunked everything. So the fan has spots on it. I think I can clean that up with some vinegar
and I don't know if I've got it bent right. It looks like it's off, but we'll figure that out
once we get it mounted. The rotor, I was talking about how the shaft might be crooked. I don't
know. We're going to have to spin it first and then maybe try to bend it. Because if it is,
it would be this part. So we're going to have to get it going and then we'll try it.
So this bearing is not supposed to be on here. That's supposed to come off. So it did not come
off in the ultrasonic cleaner because it didn't get enough of the rust off. So at risk of damaging
it, I'm going to have to get more aggressive with it. And you can see that this, I think that's
cardboard. So I've got to be really careful with that. But it's a spacer basically. This is
supposed to be mounted inside that. I'm sorry. Yeah, that. Inside that bearing. It's not supposed
to come out like that. So I mean, I could grab it with a pair of pliers, but I'm going to bend
the outside of it, which will make the bearing less effective. But the truth is,
the important part of the bearing is the inside. You know, you kind of want it where the outside
can spin and the inside can spin. But the inside is the most important because that's what the
shaft actually is going through. And so it's trying to spin the entire bearing inside the
housing and it's just, it's, it's not great. So we got to get that off of there. It's just,
it's never going to be right if that's not off of there. So, but that's all the rust the
ultrasonic can take off. I've used evapo-rust before, which is good stuff, but I think I'm
going to soak it in PB Blaster like I was joking about. PB Blaster is really is amazing because
it's capillary, is that the word? It basically goes down in any little crevice it can find,
it gets down in it. It creeps while you sleep. All right, so we got to do that. That definitely
has to happen. And I'm going to sand the sides of it here to make sure it's nice and smooth.
This back bearing cleaned up pretty good. You can put some oil and some grease in it.
It moves around. So it's going to be good. I'll put it in too far. Like it free spins in that
and it doesn't even have any oil or grease on it yet. So that's no problem. Didn't touch this
yet. I'm going to clean it up, like I said, and clean it up with sandpaper as well. The base,
it knocked some of the rust off, cleaned it up a little bit. There are these little rubber pieces
that are supposed to be on it. Two of them are missing. The front one, half of it was there,
but it broke off. So the purpose of those is when the thing is moving, especially that mine
might be out of balance, it's going to go and if you don't have those on there, it's going to
vibrate on whatever it's sitting on. So you need a little bit of something, but we could probably
make something happen there with maybe some pinball rubbers or some kind of grommet or something.
So we ought to be able to make that work. This is the front housing with the
what's left of the bearing. I think lots of oil and it'll be just fine, but I've got to
sand that out to get rid of all of that surface rust so that this can slide back in there easily.
So I got that. This is the back piece. I'll sand it a little bit too just to clean it up,
but there's not much in the back. It's just for, you know, heat dissipation. You can see the paint
pretty good there. That was under the band. That was like underneath it. So that's probably the
original color. It's like an aqua green. On the camera, it looks a little more blue than it is.
It's got just a little more green to it. It almost looks like this Weller. It's almost
the same color as that. This is another good example, I guess. Let's compare the two. Yeah,
it's the same. So I don't think it's actually faded much and that was probably pretty close
to the original color. So I think what I'll do is I'll go buy a can of paint that's a similar color
and we'll spray it when we put it back together. I'll sand it a little bit, try to make it look a
little better, but it's not going to look perfect, but it'll look better than this.
I've got to get a couple screws. I can get that while I'm getting the paint.
The fan, I think I may be able to very carefully get it to mount again with like a washer.
If I put a washer on there, it'll grab it, hold it in place. It took off most of that logo,
but you can still read it basically barely. Eskimo, I'll probably use a little bit of vinegar
on it too to see if I can get some of those spots gone, but you can see that it didn't,
it didn't get rid of that rust. So when I think Eskimo, if I think Eskimo,
let's imagine it together. Let's imagine an Eskimo and this is going to be like teal,
nice teal pretty fan. And then this blade and we'll get it shinier,
nice black cord coming out of the back. I think that would look good white. If I just, you know,
I didn't want to paint it, but it's pretty rough. So I kind of have to paint it. I'll take,
this comes off separate. I'll take it off and just leave it how it is and then put it back after I
paint it. But I think if I paint this white, um, it would look real clean and would look like ice
or whatever in my mind makes me think of an Eskimo. I don't know why the teal actually makes
me think of an Eskimo too. Why would that be? Maybe the water? I don't know. It's strange how
your mind works. Okay. So, um, I guess that's next. I'm going to sand those down a little bit.
Nope. You know what I'm going to do next? I'm going to get this freaking bearing off. I got
to put PB Blaster on it. Let it soak for a while. And then I kind of just had to grab the thing and
twist it off. If I clean up this rust in front of it here, it'll make it easier for it to slide off
whenever it gets moving a little bit. You know what I mean? Um, I don't want to mess up this
cardboard spacer. Um, I guess if I mar it up, I'll just sand it down to try to make it nice
and smooth again so that it works as a bearing in there. If you get it too small though, it's
going to make it where it wobbles. Uh, well, I don't know. The way the, this is going to keep that
pretty straight. And so as long as the center hole isn't all screwed up, I, we should be all right.
I mean, if I keep the, and I, and you know, if I get this nice and smooth like it is now,
even if it's, this is a little bit too small because I had to sand off some burrs or something,
um, it should still spin all right with lots of grease and oil.
Well, let's see what we can do. So I'm gonna do that and I'm gonna sand the inside of this,
sand the outside so that it looks, um, a little smoother. Um, and I'm gonna go get some spray
paint. Yeah. So, you know, I was joking around, but this is one of the best products I've ever
seen. Now I'm not trying to sell you anything. If you don't want to buy it, don't buy it. I don't
work for them. They don't pay me anything, but I'm going to add this to my website.
I'm gonna put this crap on my, on my, uh, uh, parts page. Someone told me about this crap many
years ago, some old man, you know, it's kind of, I think it's kind of like a Southern thing. I don't
know, but this stuff's incredible. But so I sprayed it down. I let it sit for about 30 minutes. Um,
I took a, uh, little bit of sandpaper to the rust that was in front of it so that if this was to
slide off that it would, you know, not have to go over all that rust. And then I put a rag around it
and grabbed it with a pair of pliers and just twisted it right off. Um, now it may have done
that without this. I don't know, but this crap, it has all of this funny stuff written on the can.
Work it like a pro. Blaster. Now it used to be called PB Blaster. There it is. PB. Blaster
since 1957. Revolutionary valve. Sprays upside down. Rusted nuts, bolts, pipe threads, etc.
The original nut and bolt buster. Breaks loose faster. Powerful rust penetrating catalyst.
Number one selling penetrant. Breaks free rusted or frozen parts. Protects against further rust
and corrosion. Attacks rust from all angles using our unique capillary action. Danger harmful or
fatal if swallowed. Vapor harmful. Excessive inhalation may be fatal. May cause eye and skin
irritation. Contents under pressure. Keep average or total. But that's not all folks. Blast on.
Nuts and bolts. Corroded pipe thread. Anything that is rusted or corroded, stuck or frozen.
Use an automotive, industrial, marine, agricultural, and even electric fans from the 60s.
Bonus. PB does not evaporate. It leaves a lubricating film on parts to prevent rust and
corrosion. Directions. Hey, shake the can. Completely saturate the troubled area. Don't
hold back. If you think it's not enough, go ahead give it another spray. Let sit for a few minutes.
Tap lightly and re-splut respray to hasten results. Caution. May affect some plastics.
But that's not all. Pinpoint spray. No need for a spray straw. Yeah, whenever you spray it,
it just kind of pisses on it. Blastercorp.com. Working it like a pro since 1957. Blaster brand
products are born from professional applications where only the strongest survive. We come from a
place that demands the toughest solutions and we believe you should too. As Rust Belt Warriors,
we can promise that by the time a Blaster product ends up in your hands, it's only
because the pros have told us it's the best. Okay, so they're in the Rust Belt. Rust Belt
Warriors. Made in America. Yep, this is like the best stuff ever. I thought it used to say
something on it about like, right, I don't know if it used to say this or if somebody just told
me this. Be careful. If you spray enough of this on there, it might fall off and hit you on the foot.
Manufactured by the Blaster Corporation in Cleveland, Ohio.
Danger. Breathing hazard. First aid. Don't ingest. Warning. All that crap. California. Oh, good god.
Yeah, so get you some of that. So, I'm sure they got it in a store near you. Just go buy it.
But, on our website, lionsarcade.com, there is a parts page up the top. There's a link and it's
got links to all this stuff on Amazon that we use. I need to put the Howard's
restore finish on there too. I've been meaning to do that. I'll put that on there
and this on there. If you go on lionsarcade.com, go to the parts page. There's a whole bunch of
crap that we use whenever we do repairs on our arcade games and our pinball machines and stuff.
I'll put this on there too. I've also got some stuff that kills elm trees on there that I did a
video on a long time ago. It's a whole thing. You'll have to watch it sometime. Yeah, so check that out.
I'll put it on there. If you click any of those links, it takes you to Amazon. Then, if you go to
Amazon, it pays me a commission for anybody that buys anything. So, if you buy your PB Blaster or
anything else. So, if you go on Amazon and you buy phonograph needles, it pays us a commission for
that too. So, we appreciate it. Anyway, that's not how we're getting rich though people. So, don't worry
about it if you can't do it or you're not interested in it. So, I got that off. I'm happy with that.
I cleaned up the shaft a little bit underneath it and now it spins freely in there. Of course, I'll
oil it and grease it, but now I can easily put this back in there. But, I'm going to wait till I paint
it first. So, that's the next thing. So, I'm going to sand those three pieces down. Get them smooth
or smoother. I'm not going to. Look folks, I'm not going to spend a ton of time on this. I'm spending
too much time talking, right? So, I don't have like. I'm not going to spend 10 hours saying that. It's not
going to be like a collector car or something. It's going to. I'm just going to do it right. Here we go.
All right. So, I got some Bayer spray paint that's a pretty close match to what we started with.
I guess it's slightly more blue, but that, you know, looked a little faded. So, I think we're
going to be all right. So, I've got to get this bearing back in there. That wasn't really supposed
to come out, but we'll see if I can get it back in there and bend these back to where it'll hold
in place. And then, we'll put the motor back in. Clean it up a little bit. Put it back in
and see if we can fire it up here on the bench.
I think it's going to be all right. We'll see. All right. So, I was able to get the bearing back
in there. If you look, the housing is actually cracked because that shouldn't have ever came out,
but it did. I cleaned it up. Put it back in there. It will actually move around now
and I'm going to... there was like a felt piece in there around it. I want to soak that in oil.
And then the motor, I cleaned up the plates a little bit and that's a tight fit. You got to
tap it back down in there, but I tapped it back down in there. And I've got some new screws for
it. I think they're a little bit too long, which means they'll stick out inside the fan a little
bit too much. So, I might put like a nut on them first so that they stick up. They're slightly
longer than the original ones. That was all they had at the store. So, I think I'll put a nut on
them and then that would make it on this side. It would be sticking out a little bit, you know,
the space instead of sticking out exposed where the guard mounts. It'll be in here where there's
room. You don't need anything else there. I think we're doing good so far. I haven't broke anything
yet. This tape had came loose on this side, so I had to put black. I didn't have any nice
that type of tape. But for what we're working with, I think it'll be all right.
All right, the rotor is mounted back in. I'll tell you though, it doesn't have a lot of like...
Usually, there's like a strong, you know, when I've messed with it, these magnets like really
attract the rotor and pull it one direction or the other. This one, it doesn't seem like
they're doing anything. So, I don't know if that's just because, you know, it needs to be turned on
too. The few that I've taken apart, these magnets, these are magnets, but it may not be on this.
But, you know, there's nothing pulling it. You can see the front bearing is working properly now.
Okay, so I'm going to mount the back tailpiece on. I gotta oil it up too,
clean it up a little bit, and we'll see if she spins. All right, so we've got that. There's a
little bit of play front and back. I know there were those spacers in there, the little cardboard
spacers, but I'm thinking that, you know, it's not going to matter because I believe the
the way the motor works, it's going to self-center basically.
Okay, so yeah, I'm going to wire it up. We're going to throw power to it and see if this thing spins.
Wish me luck. Well, I've managed to start getting my new paint dirty already, so I had to go
wash my hands. Okay, so I've just got a cord
wire nutted in. I put it back on its stand so it'll at least try to hold up.
Here we go. This might be really bad. If this goes crazy and catches on fire or something,
it'll probably blow all the fuses in the building and probably trip the breaker.
Have to call the power company to get it fixed again. I don't know.
This could be bad, people. There's no on-off switch either.
Ain't she beautiful? She's loud though. Should she be that loud? Should it be that loud?
I wonder what happens if you turn the polarity the other way,
polarized plug. I'd have to swap the whole wires. I don't think it would matter.
I'm just seeing if it starts the same way each time.
Yes, it is. So, I don't know if it's supposed to be that loud or not. I wonder if it's hitting
those. It doesn't feel like it's hitting anything. I'll have to watch a video of someone else's to
see if they're just all that loud or not, but it is working. Okay, so next up, I'm going to clean
this fan. I'm going to try to clean it with some vinegar to see if I can get it to look better than
this. This is pretty ridiculous, and you can obviously see that it ain't straight,
but if we can get it mounted, maybe I can tell by looking at it which blade is bent
out of crap or if they all are. That one looks like it's probably too high, so that's probably
the problem, but if I mount it, I can kind of eyeball it and might be able to figure it out.
I couldn't resist test fitting it before I clean it or try to clean it. Hopefully,
this won't fly off and kill me. If you're watching this video, it must have not.
So, it's got a little bit of a wobble. Oh, listen to that vibration. All right,
let's watch the wind down. That should tell us about the bearings, shouldn't it?
Oh, come on. Wow. I don't think I've ever had a fan that's actually well-oiled.
Let's count it. That's unbelievable, and it ain't even running right. Okay, that's at speed.
1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21. 21 seconds to wind down.
The bearings must be acceptable if it's like that. Obviously, it's not balanced right.
I don't know what you're supposed to do about that. I guess that you just keep messing with
it until you get it pretty straight. All right, so I'm going to take it off again and see if I
can clean it up so it doesn't look brown. Obviously, I haven't painted this yet, but I
needed to mount it to something so I could test it.
I'll take it back off and see if I can clean it with vinegar. All right, so I tried vinegar. It
didn't do a thing. Then I tried some Gojo hand pumice. That didn't do a thing. I tried some
Tarn-X. That didn't do a thing. This wasn't originally this kind of copper color. That's
because I put it in the ultrasonic cleaner earlier. That's part of it, but then I've got
all these spots on it. What's working really good is steel wool and this stuff. I've had this for
probably 25 years. I bought it somewhere. I don't even remember where. I probably bought it at Kmart
back in the day. This crap, anytime I want to clean something metal, this is the way to go.
I'm going to go find this before I upload this video so y'all don't all buy it
out from underneath me, but they probably still sell this at the store in a slightly
different can or something. This crap is the best stuff ever. Yeah, so it's actually going pretty
quick. This is one that I haven't cleaned. Two that I haven't cleaned. This is one that I've
cleaned and then this is one that I'm doing right now. God bless aluminum. Man, that stuff
cleans up good. I'm not even that good at it. It looks beautiful. Okay, now about the buzzing.
I think that's going to be vibration. It might be that stator in there, those
magnetic pieces I was talking about that you're looking at right there. It might be those or it
may actually be the winding. The winding, see how you can move those around? I believe what happens
is if that's not tight anymore and it's not, what happens is when you run power through it,
it all starts moving. See how that wire can move? It'll vibrate and then that's what you're hearing.
Also, if these plates in there aren't tight on each other, it'll buzz and stuff.
I think what's going on is it's just loosened up over the years. I think what I'm going to do
is I'm going to order some varnish for it where you spray it and it just makes a big glob of
lacquer. I don't want to turn it on with a fan blade. That'd be bad, wouldn't it?
All right, so let's plug it up, run it for a second, and I'll tug on the wires and crap.
Let's see if maybe we can tell if that one moves. Look at that one. See, I can move it so easy with
my hand and then there's one there too. That could be our whole problem is that the wires all just
move and that's what's making it buzz.
No, I can't tell.
It's like a hitting something. Is it hitting? I don't think it is.
Yeah, it's got to be the motor because when I unplug it, it goes away.
As soon as I unplug it, look folks, you'll be all right. Don't worry about it. You're
not even here. You can't get hurt and we don't know what's on the other end.
I don't think it's the bearings or it would do it while it's winding down. That's the freaking,
that's just the winding giving us a bunch of crap. All right, so there you go folks. I think
what I'm going to do is I'm going to keep painting it and I'm going to order some varnish
and we're going to take the motor back out, spray it with varnish, make it a big block,
you know, like you see on Transformers and stuff. We were just talking about this, by the way, on our
video on the arcade game channel, whenever we were working on the
EM gun game, trophy gun, the Transformer had a bunch of varnish leaking down the side of it.
I was saying, did this thing melt down? People were saying, no, they're just sloppy at the
factory. Well, this one doesn't have any on it. It's got coated wiring, but it doesn't have
anything. I'll tell you another thing, it gets a little warm too. These things do run hot.
I don't know if the paint's going to be too soft for this. You might need to put high temp
paint on them. I don't know, but it's a little cheap one to learn on and that's what we're going
to do. All right, so there you go. That's it so far. I also am going to paint the grill.
I've got to repair it. I've got to paint the base and then we got to figure out about the,
I'd love to be able to balance it a little better too, but when I had it out and laid on the table,
I made it as flat as I could where all four blades touch kind of at the same point on both
sides and it got it a lot better, but it ain't perfect. I think it'll work though. Okay, so
yeah, I'll order some varnish. We'll get that in and see if we can finish it up with the varnish
and the paint and the grill repair on the next video. So I hope you enjoyed it. We will see you
next week.
