Trying To Eliminate Extensive Motor Noise On This Old Eskimo Fan

Amateur Repair Time
257 followers
837 Video Views·Jan 25, 2026
Check out our Patreon page, for all of our channels. Contains outakes, concise arcade repair tips, bloopers, repair FAILS, Audio youtube wouldn't allow us to upload, and much more!
https://patreon.com/JoesClassicVideoGames
------------------------------------------------------------------------------------
Ladies and gentlemen, welcome back to Amateur Repair Time.
On our previous episode, we were working on this little Eskimo
fan, probably from the 50s or early 60s. I would guess 50s. And it was in pretty rough
shape when I got it. It was all locked up. So I took it all apart, found that the front bearing
was seized on the motor shaft, got that all apart, painted it, cleaned it, put the motor back in,
cleaned up the blade. I haven't painted this yet, the base. The housing has been painted,
the tail cone or whatever you call it has been painted, and the blade has been cleaned up.
The bearings have been oiled, and that's about as far as we got.
Now it works, but it is noisy. Are you ready to hear how noisy?
Are you ready? Don't get shocked. She's noisy. All right, now watch when I unplug the power.
So when I unplug the power, you get a really nice wind down where it takes 22 seconds. We
counted last time. So the bearings are good. The problem is the winding of the motor, I believe,
or the little stator magnets that are inside of it. Something's moving around. It's vibrating,
making all kinds of noise. The fan's not perfectly balanced. It's a little bent,
but it's almost there. I've been tinkering with it just a little bit. It's a lot better than it was.
But we're going to varnish this motor winding to see if we can get rid of any of that vibration,
any of that buzzing, and we're going to look at the stator magnets in there to see if there's an
obvious problem. I've heard that you can actually use cardboard to kind of shim it a little bit too,
so I don't know. We might do something like that. So we may have to take this in and out two or
three times, which is kind of a pain because it's a real tight fit in there. You can't just grab it
and pull it out. And then I need to paint this, and then the grill is all screwed up. So the grill,
this thing, if you didn't see the first video, this thing was rusted all to crap and was locked
up, right? So we're trying to bring it back from the dead. The rust all over it, this grill had
rust all over it. So I put it in an ultrasonic cleaner and it got some of it off, but you know,
it's not going to make rust disappear. The chrome is all destroyed. And then the little logo,
I should have probably took it off before I put it on there. It was pretty much all gone. The only
thing left was just some white paint. So that's all we've got for the logo. But whenever we took
this grill off, it actually broke. So the way it was made was there's a screw, a nut that goes on
that bolt there or that screw there, and this looped around the screw. And then whenever you
loosen the screw, blah, blah, blah. Well, when I loosened the screw, it broke it. The other one
was already broke. So what I'm going to try to do, my idea is to try to bend these where they're
kind of lining up properly. And I'm going to put a washer and see if I can like JB weld a washer
to it or something. I could tack weld it, but I'm not great at welding. I could take them to my
brother and have him do it, but I'm just going to try to put a washer on it so that it is held in
place, is tacked onto the washer, and then the washer can be mounted to the two studs. As for
the actual grill itself, I'm going to sand it down. I was going to paint it white, but I was able to
get some of that chrome look paint. I figured I'd give it a try and see if it, usually that stuff
doesn't look very good. It looks decent on plastic, but on stuff like this, it doesn't look that great.
But you know, this is so far gone, and it's so small really, that the chrome might work on it.
So we'll try it. And then if we can get it quiet enough, we'll put the tail cone back on it, and
that'll be that. So that's our goal on this thing. So first thing, I believe I'm going to start
working on seeing if I can figure out, I'm going to go ahead and sand this down so it's kind of
clean. And then we'll see if we can figure out how to JB weld or something, the washers to the
back to hold it. It doesn't have to be super strong, it just has to be where it will mount
in its place, where it goes. It's all bent up anyway, so we're just going to do the best that
we can with it. Okay, so this is how the grill turned out with the chrome spray paint. I can't
believe it actually looks that good. I mean, it don't look like chrome. It's more like a silver,
but it does look a lot better than I thought it would. I was going to paint it white,
but I saw some really good looking chrome that looked like pretty decent stuff, so I went ahead
and tried it. And I'm happy with the results. So I sanded it down, tried to get as much rust
off of it as I could, cleaned it up as best I could, and then hit it with the chrome spray paint.
And it looks pretty decent, I think. So the problem was, whenever I went to
move this off of the back of this, or the front of this actually, so the screws that go through
make little studs on the front, and this was mounted to the little studs. I want to see what
the spacing is like at the moment. Yeah, see look, they're nowhere close. So basically,
there's almost like a tension fit where these come in to fit around those studs, but that's
probably how they intended it. So the studs fit out through here, and then this looped around.
Here is the missing piece. That was like so, and you just put it around the screw. Like I said,
it's a little wider than it's supposed to be, so you kind of have to squeeze it in to get it under
the screw. And then on the other side, same thing. It went the other way under the screw. Okay,
so those were, it was so rusted that when I took the nuts off, this is after I cleaned them,
it just, that just broke. You could probably just put it back on and then carefully tighten the
screws, the new nuts, and it would probably just hold it in place. But what I'd like to do,
if possible, now I shouldn't have done, I should have done this before I painted it, but it should
be all right. I'd like to try to glue this washer to it with some JB weld, which is pretty freaking
strong. There's not a lot of crazy force pushing them things apart. So I think if the washer was
glued on there with some strong adhesive, it would hold in place. You could do it like that,
and then you would have your little rings back. You got to keep in mind though, the whole time
this thing's going to be vibrating slightly because it's a fan. So I don't know if that's
going to hold or not, but I think it might. So I'm going to try it. So I'm just simply going to lay
this down perfectly on top of these and then put some JB weld on it. JB weld holds really well
to about anything. I've got some that I used on some plastic a while back for a, it was for
that radio. I did a whole video where I used JB weld to repair that radio. The whole freaking
movement had broken out of the plastic and all of the little studs and stuff were screwed up.
And that JB weld worked amazing. I couldn't, I couldn't believe how well it worked. So we're
going to try a little bit of it here. See if I can basically form this into part of this
to where it's nice and solid. And then it'll simply slip on the stud and then you put a
nut on the back of it like it was before. And I think that will fix that issue.
All right. So I have removed the stator, which is the main part of the motor. Now, if you look,
these do not perfectly line up. So I'm wondering if that's part of our problem.
You know, it's all unbalanced. So I've ordered some varnish. We're going to,
we're going to varnish it, you know, maybe thinking that some of these wires
moving around are causing problems, but we're going to do a little test.
I'm just going to plug it in with nothing plugged without the rotor. Very quiet. So
there's nothing really wrong with the coating. I don't want to plug it in too long. This thing
would get hot. There's nothing really wrong with the varnish, I don't think, but I don't like the
those look in there. And they almost look like they've twisted, so I don't know.
We're learning here, right? Now, there is a, and that's even without the screws holding the plates
in. You know, the plates, when I pounded them out, some of them separated. But, you know,
I guess without the rotor too, you're not actually creating the movement, obviously.
But I wonder if that's, if that rotor is hitting it. See how off that is? That's not
right. That shouldn't be like that, should it? Maybe we can tell by the, I did try to clean it
up with some sandpaper, but is it hitting right there? Is that what that, where is it? It's just
hard to say. I'm gonna do some more research, I guess. See how there's a little clip there?
I guess that's part of the, yeah, there's some kind of clip. So that's part of, like,
what creates the frame, I guess. Well, lacquer can't hurt, but it would be good to get that.
Look at the, look at the difference in the thickness, though. That just, like,
what in the world? Look at that. Why would it be made like that? I don't believe that's on purpose.
This is the direction that it goes in. Well, it comes in from the other side.
I wonder what happens if you plug it in for a second, just sitting here. Hey, look, folks,
I don't think it's that big of a deal. If it, you know, if it goes shooting across the room,
which I don't believe it will, I think what will happen is this is going to make a magnetic
field that's going to hold that in place. We're hanging out of the back of it. That's not good.
Something like that. It's probably not going to work because we don't have the
bearings holding it in place. It probably won't spin. The, part of the problem is the play,
you know, like I was talking about. Yeah, this isn't going to spin without bearings or anything.
I might give it a little second though. What do you think? Is this the craziest thing I've ever
done? Even that's not really that loud. Maybe all of our noise that we're picking up is just
vibration of this thing. Well, I don't know, folks. I don't know. I know we're going to varnish this
just to make sure. I would love to get that where it lines up a little bit better too.
Let me see if I can move that around a little bit. You know, this is what this channel is for. It's
amateur repair time. I'm tearing crap apart and figuring out how it works. Okay. So, those are
definitely designed like that. They are one piece. So, this plate, like this, all of these plates,
but this top plate, if you see here, that's one full piece. See it? So, those are just,
that's how they are. I thought those middle pieces moved independently. They do not. That
is all just one big piece. So, that is exactly how it should be. So, our only hope is to varnish
the windings and to sand the inside of this to clean it up even better than I had it before
because I didn't get it very good to be honest. So, that may help. The plates being separated
where whenever I slid it out of the case, it pulled some of them apart. If it's not buzzing
when I turn it on right now, I guess it's not a problem. And you know, the screw goes here and
holds them in. And then over here, they're held in place by rivets. But it could be that that plate
is buzzing. And I can't get a ton of varnish on it because then I won't be able to get it back in the
casing. So, I kind of, in other words, I think they're going to stay like that.
So, if we, you know, if it ends up, we don't fix the buzzing. Well, we don't fix the buzzing.
I think a lot of the problem though may be this spacer
because it's allowing it to move. It's allowing it to move in and out. And that's, you know,
hitting, I think, the back of this bearing and maybe slapping the other bearings. I don't know.
That's where we're at right now. We're waiting on varnish and we got to do some paint.
All right. So, it's not making much buzzing noise at all if I just plug it in with nothing in it.
Okay. So, I'm going to varnish it anyway though, just in case. Maybe I don't understand how it
works. So, we're going to put this on it. I'm learning here, you know. So, it's not like it's
a bad idea to put varnish on it. It's just, it might be unnecessary. So, we're going to basically
make it a big blob of glue so that it will keep everything from vibrating. That's our plan.
So, this stuff is apparently the stuff you want. I bought some. They put a big sticker right on the
label. It's called Spray-On. Brand name. Spray-On EL600. Now, I saw somebody online having trouble
finding this, but it's because the part number is different. I don't know if it'll say it on here.
I searched and searched and searched and finally found it. The part number is
0600000 is the actual part number of it. So, if you search for that, you'll find it.
And they make it in different colors too. So, I just went ahead and bought a big can because
this is probably not the only fan I'm going to work on. I know that I've got two big box fans.
They don't really need any servicing. I did one video on a box fan. I did another little
oscillating fan. A small one, kind of like this one. Probably a year and a half ago,
something like that. I've got a pretty decent little Westinghouse. I can think of two more
and another one. Two, three. I've got, I've probably got seven or eight fans.
And some of them I've never done any work on. So, I'm sure that I'll continue getting fans.
To me, they're fascinating. So, I'll use this, obviously. But it would be kind of cool to get
the other colors too. So, I might get the red and the green and I think there's a black. Clear,
red, green, black, I believe. So, all you do, apparently, is just spray the hell out of it.
And it's like a big, thick, gooey varnish, you know. And it just basically glues all of these
lines together where they won't move. The thought, or the theory behind all that is,
when this thing creates its magnetic force, all of these start vibrating. And that's what makes
the buzzing noise. So, it makes them louder. So, on a nicer transformer or a nicer motor,
they would have those varnished from the factory. But this one, since it's so cheap,
I guess they just didn't do it. And we already looked at this. There's nothing I can do to move
that or anything. That's just how it's made. So, it must be correct. That's how it's supposed to be.
I'm sure it has something to do with spinning the rotor. So, I'm just going to take the clear
and basically spray over the exposed parts. Soak it all down on both sides. I'll try to
get these really good so they're nice and, you know, glued, basically, up to the leads.
And that'll be that. And then we need to test it again. We need to fit it back in the
fitting. I mean, the headpiece. I'm going to take this off and go ahead and paint it.
And I'm going to, you know, we're finishing up the grill. So, I got my washers glued on. I didn't
have the JB weld that I had. It's just for plastic. So, I've just super glued it. I don't know that
that's going to work, but I guess if it comes back apart, we'll fix it again. But, I mean,
they're glued on there. And I varnished the hell out of the motor. I put two coats on each side.
I mean, it's on there, but I think some of it can still move. If you find one that's a little
by itself, it can still move. So, I don't know that that was even necessary, but
we'll attempt it. All right. So, I'm going to go ahead and mount it back in the case.
And then we'll wire it up and see if it... I'll go ahead and test it out of the case,
see how loud it is. Then we'll put it back in the case, see how loud that is.
And then we'll start putting the rotor back and figure out the spacing on it.
All right. So, first sound test. Here we go. This is what it sounds like with the lacquer on it.
I can't hear nothing. Well, damn, that did quiet it down. I can't even hear it doing anything now.
That's interesting. I wonder if it's... I've got good connections. I wonder if
literally whenever you hear the transformer, you're hearing wires move. And now that I've
got it lacquered, you can't hear anything move. So, you can't hear anything. I don't know. Maybe.
Okay. So, let me get it back in the frame and then we'll try it again.
All right. We are mounted back in. Let's see how loud it is now.
Nothing. To the point that it's scary as if it's not doing anything.
Oh, no. I can feel it vibrating. It's working. Yeah, I can hear it barely. It is just barely
vibrating. Okay. So, yeah. So, it's whisper quiet. Whisper quiet, people. It's whisper quiet.
All right. So, now we're going to slide the rotor in. And the way it appears that it was
originally... Now, this is hard for me to wrap my mind around. The rotor goes in there like so.
The screw is on the front for the blade to mount on. And then this goes in the middle of the
stator. And like we talked about in the previous video, whenever that winds up, that's going to
find like its magnetic center. But if you've got the blade on it, as it spins, it's cutting air.
So, it's pushing air that way. So, if you think about... This is just my mind thinking about,
I might have it all backwards, but I don't think I do. It's pushing air that way, which means the
fan blade is trying to move that way. So, if you're in water and you try to swim, if you push
water behind you, it propels you that way through the water, right? So, if the fan blade is throwing
air forward, which it is, the blade itself is trying to push backwards. So, there's going to
be a little bit of an effect of this rotor trying to move backwards. So, to overcome that, they have
these spacers in there. So, on the back, they had this spacer, which is made of cardboard, okay?
And then they had these three washers. And then it goes into this bearing. On the front,
they only had one washer, but in the middle, they had this spacer. So, if you look at the first video,
when I pulled this spacer off, this is cardboard too, when I pulled this spacer off, this part of
it that's all messed up was pushed up against the rotor in there. So, in other words, this had been
smashed that way. Now, how in the hell would that happen? It would happen if this had been pulled
on. You know what I mean? So, there's a space taken up by the spacer and that washer to the front bearing.
That would never get smashed as hard as it was. It might get, you know, cut up or something, but it
would never get smashed that hard unless this blade and this fan had came this way to smash it.
So, I think what's going on is part of the noise is this moving because the blade is a little
unbalanced. I've got it better now, but it's a little unbalanced. And so, I think this is probably
moving like this the whole time in there and that vibration is making a bunch of noise too.
Also, the last time I had it together, I had this on backwards. This bearing should be centered
and it also spins around, but there's a wick here like a tube to oil it with and that goes up
because the oil hole is on the top. So, you pour oil down in that and it lands in that hole,
believe it or not. Theoretically, it goes in that hole and then gravity takes it down and it oils
the bearing. So, I had this on backwards last time, which shouldn't really matter,
but if it was worn, like maybe the whole time this is blowing, there's like this type of
force on it. So, maybe that side of the bearing is more worn than the other side or something.
We're just spitballing here, folks. So, here's what I'm going to do. This thing is obviously
screwed, but look what I found. I have this. This is a vacuum tube plug for your carburetor
and it's a pretty good fit on that shaft. All we need it for is a spacer. So, what I'm going to do
is I'm going to cut it a little long, maybe out to here, to make up for this smashed one
and then put it on there and use it to space this out. Hopefully, that will fix our problem,
but I don't know how long this is supposed to be. It's so smashed up, you can't really tell
how long it originally was. I mean, it kind of looks like it was just a little bit longer.
Yeah. So, we'll run that as a spacer and then we'll put this on the very end
and then that will butt up against our front bearing. If you didn't see the previous video,
that front bearing was completely seized. So, I broke it all apart and we ended up,
whenever we took the fan out, the whole thing came out with the bearing still on it. It was
all screwed up. So, I need to figure this out. I think what I might do is just go ahead and mount
I think some of that clacking we were hearing was maybe this hitting the bracket going forward. I
don't know. So, I think what I'll do is mount this without the spacer and then the back spacers in
the back piece, turn it on, hear how loud it is, and see if we can tell where it's trying to center.
We might be able to mark it with a marker or something and then that will help us figure out
how long the bearing should be or I mean how long the spacer should be. And then,
if we can get it where most of the slack is out and there's just a little bit of play,
maybe that'll quiet it down. All right. I don't want to run it too long without the
fan on because that helps cool it, I think. I wonder if I can score it with this screwdriver.
Pretty quiet. I mean, it's quiet enough. I'd be happy if it stayed that quiet,
but I think with the blade on, it's going to be loud again. Okay. So, let's see if we can make
a spacer that makes it line up about like that. And this is what the back looks like.
So, there is my new spacer. A little bit longer than my old spacer. I cut a little bit too much
off, so I put it back in there. So, it's a little longer than my original spacer.
And with the bearing in place, I think it'll put us about where we were when it was rolling. So,
we'll see. Okay. So, I might have a little bit too much in there because I don't see my mark.
It's snug. I mean, it will barely move, but it still spins free. So, let's see if it's
loud like that because we may be slightly off its magnetic center. Definitely louder.
If I allow it to go forward, it sounds a little better. And the blade is going to be pushing it
backwards. Interesting. So, but another thing too, let me try something else. I didn't overly
tighten these. I left them kind of loose. So, maybe my plates are a little loose. So, let me
tighten these up more. Just exactly how it is now. And we'll see if that does anything. Okay. I
tightened them up. It's still loud. I think I've got it off center because I made that spacer too
big. I need to make it slightly smaller. Okay. So, that one little sliver of the rubber piece
that I had cut off, I took off this side, but then I put it on the backside so that we still
have the same lack of play. It basically just barely will move. Okay. So, I basically shifted
it from here to here, just barely. And we have the same amount of spacers. They're just on opposite
sides of the motor. So, let's see if that changed anything. That's better, but I don't know that
I may have went too far with it. I can't tell by my marking. Doesn't that look like maybe it's a
little shorter than it was? I think maybe I should have split it in half. You can hear it's like,
I think it's hitting those bearings. That's the noise that we're hearing.
I think if it was back a little bit, I think we're about halfway there.
I think that is my mark. So, I think I'm just a little bit too far out. So, I need to go,
I need to have a little more spacing on the front instead of the back. So, I need to move maybe one
of those washers. Well, what do we think? I think I may try giving it, take out one of the washers,
give it just a little more in play and see if that improves it or makes it work. It's not really good
to run them without the blade because this heats up pretty quick. If the blade's on it, it's
constantly cooling it because it's moving the air around. But I think we've got it. And there's a
apparently I had it compressed before. There's just a little bit of in play now.
I think we're good. Okay. So, I need to clean it up. I need to get my mount ready
so I can put this back on the mount. And then we need to try to mount the fan blade back to it and
see if we can get it to not be really noisy with the fan blade on. All right. So, I got the base
out of the paint booth. I was able to clean the shell up here that I had gotten looking kind of
ugly with some wax actually. Wax cleans really well. If you just take car wax and you can clean
paint with it really well. That's actually what wax is for. And I have bolted the fan blade back
on. It's not close to the thing and I've straightened it out pretty well. It's not perfect,
but it's a lot better than it was. So, the way I did it was I just looked at. So, there's the
closest point that blade is to that bolt. And then you turn it to this blade closest blah blah blah
there and there. And you just keep turning it until all of those are the same. And then you do
the front the same for the front. You can kind of eyeball it and see if you can figure out which is
like. For instance, it looks like that one has bent a little too far forward. Yeah. See how that
one is more forward. Like if you line it up with something in the background like that red
radio there. It's just on the edge of that red radio. That one's off. That one's about the same.
That one's about the same. That one's about the same. That one's back. So, this one we could bend
forward, but you don't want to bend the back back too far. So, you know, let me mess with that a
second. Well, it's pretty good. It's not perfect, but it's better than it was. And also, if you
didn't see the previous video, I didn't paint the fan blade. I just cleaned it. That's an aluminum
blade. You could actually polish it and get it real shiny, but I don't know that it originally
was really shiny. Okay. So, we've got it on there. I think we've got our spacers just right. Now,
if I move this, now that I've got the base on it, you might be able to see there's just the
slightest bit of play, but I think you need it like that so that it has, you know, if it's too
tight, it's going to, it's not going to spin freely. It needs a little bit of play in there.
You run into the same thing on pinball flippers. Like whenever you've got a pinball flipper
there, it goes through a bushing, like kind of like this is set up and there's a clamp on the
bottom of it and then it's held in place by the bushing on the top. And we've got the same kind
of thing going on here. Well, if you get it real tight where it's perfectly held in place,
the damn thing won't flip because there's no room. It's got to have a little bit of play
so that it can move. Okay. So, I think we're good to test it again. Hopefully,
she has quieted down. We need to do something about the rubber feet. We'll mess with that later.
Let's see what we got. Oh yeah. I can live with that. Putting out some air too.
Part of that noise is just the vibration on the desk. Okay. Let's watch the spin down.
Somebody asked on the previous video, isn't that, isn't the fan of that age supposed to spin
clockwise? Well, I don't know. It's spinning counterclockwise and it's blowing air. So,
I don't know. I don't think so. It doesn't appear to. If you look, the blade is bent
forward as it spins. So, it would catch air and then throw it forward. I mean,
I guess that's how that works. And hell, it's working. So, I guess that's how it's supposed
to spin. But that sounds a lot better. I think I'm happy with that. I think that's probably as
good as I can get it. I've seen other ones that are more quiet, but that's probably as quiet as
I can get mine. So, I'm going to put a new grommet on the tail cone or whatever this is called.
I'm not going to worry about putting tape on those because that's how they originally were.
They were just kind of like that. I'm going to tie a knot in it so it can't pull through here.
Put a new grommet on it and then button it back up and then we'll put the guard back on it and
hope it doesn't hit. And then we need to look at the feet a little bit. All right. So, there are
these little rubber wheels on the bottom. This is a great example. That's a rivet and it goes
through a rubber disc and there's three of them. One, two, three. And it protrudes down underneath
it just slightly to absorb the vibration of the fan. So, I need to get some of those. I looked
on eBay and that you can actually buy just flat rubber washers. These are 5 8ths of an inch in
diameter and they're 3 16ths of an inch thick. So, I'm gonna do my best to find that. It's actually
pretty quiet. I mean, not quiet, but how do we measure how good the fan is? All right. So,
I think our little spacers did the trick with the noise. I put the nose cone back on it.
All of that is really good. The guard, my little super glue trick, didn't work of course. I'm
I think if we just tap tap those two pieces together, we can get them to wrap around the
screw again and hold them in place with a nut. So, other than that though, I think the thing
turned out really nice. And I like the, I don't think it's out of line, the sound or anything.
I think that sounds pretty good. Pretty cool. All right. So, if I get him to tack weld that
before I put this video out, I'll show it to you with the cage back on it. But if I don't,
I'll show it to you in an update down the road and as part of another video or something.
But we won't do another video on this particular fan. It's two videos is quite enough for a,
that fan was probably like 10 bucks new or something like that. All right. You want to
see the wind down one more time? I'll show you the wind down, then I'll show you the start up
again. So, let's count it this time like we did last time. Four, five, six, seven, eight, nine,
10, 11, 12, 13, 14, 15, 16, 17. It's actually, it's actually quicker than it was before. Before
it was doing 22 or something like that. But you know, that could be too, that could have to do
with how the fan blades are bent. Like whenever they were out of, I don't know. No, I guess we
don't have to analyze it. All right. And this is what it's like when it starts up. Yeah. It's so
cool. Oh, it's cool. Literally, literally cool. All right, folks. I hope you enjoyed the video.
Let me know what you do with your fan cages that break weldments on it. You know, that's a pinball
thing too. Weldments break on pinball, ball guides all the time. I've got another fan,
kind of similar to this with no cage at all on it. The cage is just missing. And then I've got
one, two, I think I've got about three, just slightly bigger than this that have,
that have cages. And then I've got a, like a eighties model oscillator. That's really cool.
The plastic ones that were blue that everybody liked. And I've got a box fan. I had two, two of
the big, you know, Lakewood box fans, but I just sold one the other day, making room. When I bought
this, I sold that extra box fan I had, you know, I can't, I've only got so much room here at amateur
repair time. We can't, we can't be just piling stuff in here. Okay. But I'll give this a place
of prestige. I think we quieted it down really well. I just think it sounds a heck of a lot
better than it did. So leave your comments below. Let me know what you think, and I will see you
on the next video.
