How to read, test, fix, and clear a Harley Cal 03 engine code with only a simple volt meter. Here is the regulator I used. OEM was $300 this was $42. I will come back over time with a review on how it lasted. https://amzn.to/4pzaNRA Tool 2 Wrench Amazon Store Links: https://amzn.to/2Ujfu5F Use these tools links to support How2Wrench and know we use the same tools as seen in the videos! Join this channel to get access to these perks: https://www.youtube.com/channel/UCBhM8DCKnT3qXwTW0eToyCg/join -Daily MEMBER FIRST COMMENTS ANSWERED FIRST -Live Q/A video chats -Wonder if we have a video on your need? Members can request content links! -Full Access to the ENTIRE 700 video library -Member-Only FREE tool giveaways One on one Techline: https://how2wrench.com/ols/products/techline-one-on-one Below are some links that help support me and my work. Keep Wrenching, Shane Conley Instructor/Motivator/Motorcyclist
Well, that's never good. Let me show you how to fix it.
All right, let me show you how to do this. We want to make sure that our run switch is in the
run position. I'm going to try and do this one-handed. This is just setting on here loose,
but you want to hold this reset button here and turn the ignition on at the same time.
Okay, so we are in diagnostic mode right now. You can see that we have this bank one,
I think they call it. So it says clear. So as I cycle through these, two, three, four, five,
six, seven, eight. Oh, and now I have a problem. Okay. So if I take a look, I have something there
that says set. If I go one more, it looks like nine's clear, 10's clear. And then I have this
Cal003, which you'll see when we Google that, that's an issue. Okay. And that starts over.
So if we go back through here, just to double check, we got that, the 08 set,
and then we have that Cal3 as an issue. Okay. So let's go research that code and see what we come
up with. So if you do a quick search on the internet, you're going to see you get this
generic message that just basically says a sensor calibration issue. It gives you some stuff that
you can look into. As I look through these, I thought, well, what could I do quick? What could
I do it yourself or do? And one thing that you can always do is often overlook is just check the
charging system, including the stator, voltage regulator, crankshaft position sensor. So the
bike wouldn't run at all if the crankshaft position sensor is completely bad or disconnected,
the bike wouldn't even run. So since it runs, I could do a stator check really quick, right?
So then I just kind of kept looking through here, thought I'd see maybe what I could find.
And this very first one here was awesome for the fact that it came up with the two that I have.
I have that 08 set and then the calibration, I'll call it Cal03. So let's look into that and you'll
see this first thing on the top answer is the gauge code could indicate a voltage issue, usually
suggest the regulator. And this is where it got me the information on where I wanted to try and go
with this. And I, this very first top answer here, thanks to PJ on this was a faulty regulator
stator. Before we fix the problem, let me test it to verify this is bad. This is an easy test to
test the charging system. Just put a multimeter across the battery on DC volts, red, red, black
to black and prove that it's actually faulty. Battery's a little bit discharged from trying
to start a few different times here. No key on, I'm at 12.3. Let's go ahead and fire up the bike.
Really high voltage. What that is, we'll look it up here, means we need to replace the regulator
rectifier, but I'm gonna prove that I can make that code go away simply by disconnecting the
regulator rectifier to prove that that's the problem. Something to think about here is since
we started with a low battery at that 12.3 instead of 12.8, that means that this would have been most
likely over 17 or right at 17 because the charging system adds to whatever the battery voltage is
that you're starting with. So this failure was pretty high actually. So what we're going to do
now is we're going to go ahead and disconnect the voltage regulator rectifier to prove that
the problem goes away. But I'll just take you along on the journey here. Let's go ahead and
disconnect that. So the first thing you'll notice is I was, a big reason I wanted to put this back
on is these bolts were actually really loose. They were about ready just to fall off and that
could be what caused the problem of the regulator to ultimately fail is when these don't have,
you know, good connection, all these electrical connections will overheat and that could just be
what ultimately caused the regular rectifier to fail. So let's just go ahead and pop this off
and prove it. All right, couldn't do that one-handed. The detent on there is right here.
Push that in and then separate the two. So we are, let's get our ground off there completely.
We are completely disconnected from the stator and the regular rectifier. Let's fire the bike
back up and recheck our voltage output. Now what we would expect to see now is just no change in
voltage. We'll have a little bit of drop from just turn the key on, but we aren't going to see
any added because we've disconnected the stator and the regular rectifier. So we are just running
on what the battery has in it, nothing else. But what we're going to see is our big overvoltage
go away and we're going to see that that code doesn't show back up. All right, let's see with
key on. We're at 12.2 or so, starting to get a little low. Let's hope there's enough juice to start.
We are good to go. So as you can see, that confirms that at a minimum, we have a problem
with that regular rectifier. So an overvoltage issue can really hurt things. So with that failing,
that's a fail-safe mechanism to not hurt like the ECM or anything else. I did notice one bulb was
burned out. That could be from that. So we'll go around and start to check all the lights and see
that might just be coincidental that that's burned out. Let's see here. We got a headlight switch here.
Looking pretty lucky so far. How about tail lights and turn signals?
That one's good. Hey, not blinking though. And that is because the front light is burned out.
That's why. So hey, not too bad. We got pretty lucky that we only have one bulb that popped on this.
What we'll do next is just swap out that regulator, retest everything is good, and then get this bike
back on the road. All right, remove two bolts, slide this tire shield up and out of the way.
You do not have to remove the tire. There's the breaker, that wire right here with the yellow
marker on it. That is the one coming from the regulator underneath the pipe into the front of
the motorcycle. If you look at your new one, these leads may be significantly longer than OEM. You
have to address that, but this is the one that I need to put on that breaker. All right, let's fire
this back up. I'm gonna run my own fuel to the carb. I just got the dash bungee corded up here,
a meter on here, and we are going to see if we were more in that 14 and a half,
maybe 15 max range to have that problem go away. Let's see here.
All right, my friends, there you have it. That's how you fix the Cal
03 code on an older twin cam. Make sure and like, share, and subscribe.
Make it a great day and keep wrenching.