Mazda 3 Mechanical Review

The Auto Geek
46 followers
20 Video Views·Oct 18, 2022
Today we're going to be reviewing the Mazda3. Now while most car reviewers would praise the
Mazda3 for its excellent handling characteristics and giving the Civic a run for its money,
we're going to be taking a look under the hood and underneath the Mazda3 to see what's inside
and how it works. And we're going to start under the hood where we have Mazda's 2.5 liter SkyActiv
G engine. This is a four-cylinder engine situated transversely for front-wheel drive. Now
unfortunately this one does not have the turbocharger but there is an option for you to
get one on a Mazda3. Now on the driver's side underneath the battery is a traditional six-speed
automatic transmission. Taking a quick look at the layout of things under this engine here we
have the windshield washer and coolant jugs off to the side here. Over on this side we have the
air box, the battery, the fuse box and the ECU behind the battery along with the master cylinder
reservoir. Now we're going to start here with the air intake path. Now cool air is going to be drawn
in from the front of the Mazda3 and head into this air box to get filtered out. It'll then pass by
this mass airflow sensor and then into this drive-by-wire throttle body and directly into
this plastic intake plenum to get burned. There's no extra ducts or tracks it's just a very simple
setup. Continuing the theme of simplicity is changing the air filter. You just have to remove
these two tabs here and then pop up the air box and remove the air filter. Now the air box itself
is also pretty simple although you do have this big resonator it sits down in front of the
transmission. Now with that air box out of the way we have clear access to the drive-by-wire throttle
body. There's also a manifold absolute pressure sensor down here. Now this plenum does not have
any extra flaps or actuators for tumble flow control the way other vehicles do. Next we'll
take a look at the fuel system on the Mazda3 and things are pretty simple although this is a direct
injected engine. We have the fuel line that's going to bring fuel into this direct injection
pump. This is going to be the high pressure pump that's driven off of the exhaust camshaft over
here to pressurize the fuel. It'll then go down over here to the fuel rail underneath the air
intake plenum. Now underneath that intake plenum we have the four injectors that are going to
inject fuel directly into the combustion chamber. You can see a piece of the rail on the side here
as well as the fuel pressure sensor. Now of course the downside to direct injection only is that you
could potentially deal with carbon buildup issues on your intake valves. If you did have port
injection you would see port injectors right on the top here. Taking a look at the top of the
Mazda3's engine we have a plastic valve cover here. There are four ignition coils on the top
here for easy access to the spark plugs when you do need to change them out. At the top here we have
the purge valve for the evap system and a small little oil collector before it goes back down to
the intake to get recycled. Now the top of the engine here we do have the filler cap. Now this
does take 0w20 weight oil and we have the dipstick located right at the top here. Taking a look at
the underbody of the Mazda3 things are fairly flat throughout. There's a good use of plastics
underneath here to smoothen out aerodynamics and to help prevent salt water from splashing up on
components rusting them out. Now at least you don't have to take off the whole cover underneath here
when you're doing an oil change. There's just this little access panel here that you remove
and in this case it's missing and that gives you access to your oil filter and your drain plug
unlike say a Nissan or a Volkswagen where you got to take off the whole thing. This cover is not even
made of plastic it's just a really thin sheet of metal coated with some furry stuff. Now with that
under cover removed we have clear access to the engine on the passenger side and the transmission
on the driver's side. Now looking up at the oil pan we have this oil level sensor over here we
have the drain plug located over here and we have a canister style oil filter over here for quick
and easy oil changes. Now the oil pan itself is pretty accessible all the way around here if you
do need to change its gasket. Now this big plastic box underneath the intake manifold is actually the
system. The PCV valve is integrated into the block itself and it'll then come out to this
oil separator before directly venting into that intake manifold. Now looking off to the passenger
side of the engine underneath this cover here we have a timing chain which is good because you
don't have to change that over the life of the vehicle the way you would have to in a timing belt
setup. Now this engine has dual overhead cams we have the intake on the front here and the exhaust
down at the back here. Now the intake side does have variable valve timing that's electronically
controlled through this electric motor here that has a planetary gear set inside and that's going
to vary the phase of the intake camshafts relative to the crankshaft. Now on the exhaust side it uses
variable valve timing but it's a traditional oil control. Now the oil control valve is actually
this one on top of the valve cover here the oil control valve you see down there is for the cylinder
deactivation system this one here being for cylinder number one. The deactivation solenoid
for cylinder number four is located off on the exhaust side somewhere behind this high pressure
fuel pump. Now just in front of that timing cover is your drive belt setup you can see this here is
where the alternator is located now the tensioner for it is located down at the back there it's
actually best accessed from the side wheel well. Now removing the alternator here is pretty
straightforward you got a lot of room to work over here and it's just two bolts that'll bolt it to
the block. Now towards the firewall side of the engine we do have a secondary accessory belt that
powers the water pump and here's a look at that drive belt setup from down below you can see
things are pretty tight between the frame rail and this AC compressor and the belt side of the
engine. Now this AC compressor is pretty easy to change out there's just a couple of bolts that
hold it to the block luckily in order to get the alternator out you can get it out from the top
and you don't have to remove this guy. And now we'll have a listen to a cold start. Now one thing
about Mazda engines is that they're not really well refined have a listen to that direct injection pump
you really hear that clicking sound going back and forth which can get pretty annoying. Now the
Mazda 3's got three engine mounts we have the first mount over here on the passenger side
the second one over here is on the driver's side underneath the battery that connects the
transmission to the subframe. Now the third engine mount is located underneath here right at the bell
housing of the engine and the transmission and it'll tie it to the subframe. Now this engine
mount kind of looks soggy I wonder if it's a hydraulic bushing. Taking a look at the transmission
on the Mazda 3 it's amazing that they're still using a regular six-speed automatic transmission
most other manufacturers like the Corolla and Civic have gone to a CVT while other manufacturers
still use like an eight-speed or a nine-speed transmission. Kudos to Mazda for sticking to the
tried and true six-speed. Now the main feature of the six-speed transmission is actually down here
once you remove this bolt you have access to a real dipstick which is good because you can check
your transmission fluid without any fancy scan tools or having to rely on a dirty overfill plug.
Also traditional is the shifter uses a regular cable to change your gears from park reverse to
neutral and drive some other vehicles are going to a fully electric motor to do that job. Now in
front of the transmission we have its cooler which is going to bring these coolant coming
through these lines here to exchange warmth with the transmission fluid. Now if you look down you
can kind of see the bell housing and this is where the starter motor is located it's actually easier
to service it from down below. Here's a look at that six-speed automatic transmission from
underneath we do have a steel oil pan which is pretty easy to access we have a drain bolt on the
bottom here so that combined with the dipstick up above is going to make for some pretty easy
transmission oil changes. Now just above the oil pan is the transmission cooler and then just behind
that here is the starter motor so accessing it from the bottom here is definitely much easier.
Now once that transmission is done changing through its six gears it'll then send power out
to the front differential located inside of this housing over here and that'll then go out to each
individual axle. Now some Mazda 3s do come with an all-wheel drive system and that's why you have
this big empty space inside here because this is where the transfer case would sit and that would
translate some of that power going from sideways to the longitudinal direction to a drive shaft
that would lead down this tunnel here. Now if this was the all-wheel drive model you would have that
center differential run down the middle over here and come to a rear differential which would be
mounted on a subframe of some sort and then the axles would go out to each wheel. This is the
two-wheel drive model so things are pretty simple you have the four bolts there for your hub so you
don't need a press in order to change wheel bearings. Overall under the hood of the Mazda 3
things are pretty easily laid out to maintain there's not too many hoses wires or electronics
that you couldn't figure out. Now over here on the driver's side we do have the battery and we have
the fuse box. Now the fuse box is easy to access and things are pretty nicely labeled. Now at the
back here we have the ECU. Now typically I don't like ECUs in the engine bay because of heat cycling
and collision damage but I like how Mazda's put it right up against the firewall here where it's
well protected away from any collision damage. That's a pretty good idea yet it still maintains
a nice short wiring harness to the engine. Now looking at the subframe structure under the Mazda
3 things are very traditional here with a stamped steel subframe and it's a fully boxed in frame that
goes all the way up to the front of the vehicle and even includes this metal cross tie underneath
the radiator support which is good because most vehicle subframes just pretty much end at the
control arms and the rest is just left hanging. Now looking at the front suspension from underneath
we do have these steel knuckles here and you can see the bolts here for a bolt-on hub which means
that if you've got to change front bearings you don't need a press to change it out however the
ball joint is a Preston style design that presses into the stamped steel lower control arm. Now
changing control arms in the Mazda 3 is pretty straightforward you do have one bolt at the back
there however the one bolt at the front here is pretty close to this transmission pan so you might
have to jack up the transmission slightly in order to get it out at least on the driver's side.
Overall though underneath here things are pretty simple and I'm actually surprised that there's not
too much surface rust especially for being a one year old Mazda compared to some other Mazdas I've
reviewed. The only thing I see here is that although you do have a splash guard a lot of the stuff here
is getting splashed with mud water so I don't really know the effectiveness of it. Looking at
the front suspension on the Mazda 3 things are very traditional here where we have a McPherson
strut suspension here that comes down to a steel steering knuckle. Now the joint between the strut
and the steering knuckle uses a pinch bolt which is known to rust in there so when you do have to
replace the strut it's really hard to get out make sure you rust proof your car. And from the back
here you can see the stamped steel lower control arm with your inner and outer tie rods. Here we
have the stabilizer link that joins up with the strut over here and to the sway bar which goes
over to the other side. Now one interesting thing is Mazda's got this little rubber weight on here
for resonance and vibration damping. Now the lower ball joint also uses this pinch bolt design into
a steering knuckle so that could definitely get stuck when it's time to replace that ball joint.
Overall having a McPherson strut suspension is going to be a pretty good idea for an economy car
because it's going to be pretty cheap to maintain and easy to work on down the road. Now although
McPherson suspension isn't going to be the best in terms of handling the Mazda 3 has done it pretty
good and shows that you can definitely do a lot with very little. I think someone's been having
too much fun with this Mazda. Now taking a look at the rear suspension this is where Mazda has cut
costs. Instead of using a multi-link suspension like previous generations or like the competing
Civic and Corolla they actually use a twist beam design. This is a much cheaper design to
manufacture but it does have negative effects on handling. Now for the twist beam design we
have a torsion beam that runs from this side over to the other side. Now this is a dependent
suspension system so the effect of one wheel moving up and down is going to affect the other
side and the difference between them is going to cause torsion in this torsion beam. Now a torsion
beam being very simple in nature is just connected to the body at these two bushings one on this side
and one at the other side. We have this spring here that connects the body to the actual torsion
beam at the bottom here. Now the back here we have the shock absorber that will attach down
to that torsion beam. Now taking a look behind this torsion beam here you can see that the beam
actually has a pit over here where the spring seats and then it also has the attachment point
for the shock absorber and that also forms part of the knuckle itself so it's all one piece of
stamped steel. There's no separate cast steel piece for these knuckles. Now of course the best
part of the twist beam design is that it's very simple to work on. To replace shocks on this you
just have one bolt at the bottom there and then two bolts up at the top there that you remove.
If you want to change out springs to lower your car you just have to remove that shock and the
spring should just jump right out at you. The other thing about this is things are not going to wear
out nearly as fast. You don't have extra links and arms that have different bushings and ball
joints on them that are going to wear out. You just have these two bushings over here that don't
really see too much stress because this whole arm just pivots up and down. Now obviously the biggest
downside to having this twist beam design is that you don't get good wheel control and therefore
handling and when the suspension articulates up and down you don't get the desired change in camber
angle as you would with an independent rear suspension. Now that twist beam design is also
going to give you a lot more space back here to put other things like a hybrid battery or a fuel
tank and you don't even need a subframe for it. It just bolts directly to the frame. Now overall I do
have to ding Mazda for having this twist beam design especially that its competitors Civic and
Corolla do have an independent rear suspension and the fact that this platform already comes with a
multi-link suspension in the form of the Mazda CX-5. Now the Mazda 3 still uses this twist beam
design even on the all-wheel drive model. Now one other thing that's missing is a rear sway bar.
Obviously you won't have that on a rear torsion beam because the torsion beam itself
kind of acts like a sway bar. Now there's no arguing that the LED headlights on the Mazda 3
do look pretty sharp. Now if you do have to access it for whatever reason at least on the driver's
side you have clear access to the LED controller at the back here. Now everything else is LED so
they shouldn't really burn out. Unfortunately though on the passenger side things are a little
bit more difficult to access with the windshield washer tank and coolant tank in the way. Take a
look at the Mazda 3's exhaust system. Now this is not the turbocharged model but it does have a
spiral jumble of a manifold so in fact all four cylinders here have to come out then make a spiral
through the catalytic converter before going down to that flex pipe. And here's a look at that mumble
jumble of exhaust from underneath here as it leads into that flex pipe. It'll then get sent down to
the second two-way catalytic converter underneath here and then out back to the tailpipe. Now that
exhaust is then going to travel to the back here around the rear torsion beam and into this
transversely mounted muffler. Now that muffler has dual outlets on either side. Now that muffler has
dual outlets on either side. Now there's no fake exhaust tips there's actually cutouts in the
And now we'll have a listen to the exhaust.
Next we're going to take a look at the Mazda 3's cooling system. Things are again pretty
straightforward for the most part. We start here at the coolant overflow jug located off to the
side here. It's going to bring coolant inside of this radiator located at the front here.
The upper radiator hose is then going to bring coolant down across this way to this junction
inside of here. Unfortunately once the coolant gets inside of this junction box things are going
to get a little complicated. Instead of using a traditional mechanical thermostat Mazda is using
an electronic cooling valve which is going to use temperature sensors and an actual motor inside of
here to allow or restrict the flow of coolant depending on its temperature. Now this valve
we've also got lines that tee off and go to the heater core, the transmission cooler down below,
as well as the lower radiator hose. Now the lower radiator hose is going to come from that junction
down over here and connect over here on this side of the radiator. And then of course we have the
water pump which is belt driven off of the crank here on the front side of the engine. Now accessing
this is going to be a little tight because you have the frame rail right up against it. Now looking
up through the splash guard you can see we've got the water pump up at the top there that's driven
off of the crank shaft. Of course because there's frame rail in the way getting at those water pump
bolts is going to be a little tricky even though you have this side cover off. Now the interesting
thing is this belt here is actually a stretch type belt there's no tensioner on here. The
instruction manual actually says that you have to take your brother's old sock here, squeeze it in
between here and then when you rotate the crank the rag is going to allow that belt to peel off
and peel back on. Now one good thing about Mazda's big front overhang design is that you don't have
to remove this whole entire front bumper assembly. Once you remove the cooling fan assembly this
radiator will just pull right out. Now the front here Mazda is kind of cheating by trying to get
away with a single electric cooling fan slightly off on the driver's side. On the passenger side
things are just blocked off and here's a look at the cooling fan setup from underneath. Once again
you can see the fan mostly on the driver's side while the passenger side is more or less left
blank. Now Mazda is also very nice to give you a radiator drain port so you don't have to remove
the hose just to drain the coolant. Now if you thought that this big grill that Mazda is using
is great for cooling well most of it is actually blocked off in the parts that aren't blocked off
are just blocked off by the bumper rebar so you really aren't getting much air in there from the
upper grill. Now the bottom here we have these active grill shutters and that's there to balance
aerodynamics with cooling capacity. Next we'll take a look at the Mazda3's braking system and
we'll start here at the master cylinder. It's got a little bit of a weird shaped reservoir that does
go back to a traditional brake booster sitting behind here. Now that brake booster is vacuum
powered but the vacuum if you follow the line actually comes to this vacuum pump which is driven
off of also the exhaust camshaft same like the high pressure fuel pump. Following the master
cylinder's line across the firewall leads you over to the ABS module underneath this windshield cowl
here. Now this is responsible for any traction stability control as well as any autonomous
braking features that this car comes with. Speaking of autonomous braking features we have the radar
sensor which is in behind this Mazda logo that's why this logo is nice and flat. Now having it
there is better than having it down below here like some manufacturers do where it could easily
get hit by a runaway Thanksgiving turkey. Speaking of getting hit most manufacturers would be wise to
cover up the area behind the bumper rebar. Now in this case they actually use grill to cover the
bumper rebar so if you were to take an impact you have to break this grill before it bounces off
that rebar. Now taking a look at the front brakes on the Mazda3 things are very traditional here
where we have a single piston floating caliper here on a disc rotor. Now these brakes are kind
of small but after all this is an economy car. Taking a look at the Mazda3's rear brake setup
we have a floating caliper design at the back here with a disc rotor. Now there's no drum inside
here in fact the parking brake is electrically actuated through this little actuator over here
which is going to squeeze these pads together to lock this disc up. The rear caliper on here is
actually at a weird angle most vehicles either put it in the front or in the back here but the
Mazda's chosen to go at a 45 degree upward over here. Now looking under the Mazda3 here at the
fuel tank it is covered over here it is made of plastic and because this is not the all-wheel
drive model there is no center drive shaft running down here which means that this tank is just one
big flat piece. Now if you follow these lines coming from the fuel tank the evap canister is
located behind the right rear wheel well. Now luckily accessing the low pressure fuel pump and
the filter is pretty easy with this access panel just below the rear seat. Overall though I'm pretty
impressed that almost every surface underneath the Mazda3 is fully covered with the exception
of this part just above the torsion beam. I wonder if it's Mazda's bad reputation for rust
that they're trying to hide something. It's interesting how aerodynamics are even shaping
the way the exhaust system is now. This muffler is basically a rectangle instead of a normal
oval kind of shape that it has. They've even got an aero piece on the bottom here near the back
bumper where there's just wasted space. Now in terms of build quality I think Mazda's done a
pretty good job in the interior choosing a lot of higher quality materials especially considering
this vehicle's class. There's a lot of soft touch materials throughout the whole cabin. Now of
course if you want a nitpick you can find some first year quality issues such as the chrome here
peeling off on the grille and some of these pieces here being a little loose. But what really matters
is what's under the hood and I think Mazda's done a really good thing here by using a tried and true
powertrain with just a simple naturally aspirated four-cylinder and an automatic transmission and
it still manages to give you good power and still be relevant today. I'm looking at you Nissan Sentra.
Now overall I think Mazda's got a really good formula by giving you a fresh interior and exterior
design with internals that are going to last you a really long time and be very sensible to work on
especially for a non-luxury car in this class. Now the only thing I'd wish for is if Mazda could
offer a faster version with an independent rear suspension. I think that would really knock the
Civic Type R and Corolla S out of its class. And now it's time for you guys to tell me in the
comment section down below what do you think of the Mazda3. Do you think that it's time for Mazda
to update some of the stuff under the hood or should they just leave it as is and it's a pretty
good contender? Now make sure you follow me on Instagram to find out what the next car review
is going to be and subscribe for more videos just like this one.
