Diesel Turbo Inspection: Don't Skip These Steps

Charley’s Garage
78 followers
2 Video Views·Jun 4, 2026
This is video 5 of 100 diesel videos in 100 days! Every 5th video is going to be a members only video until we get to the end of the series! Gotta reward those Garage Owners and Garage Cats with some exclusive videos. All the visual inspection basics of turbochargers are covered here and make sure you get a dial indicator!In this video, we're diving into the visual inspections and diagnostics of a turbo charger, specifically from an IH DT-466 diesel engine. We'll show you how a mechanic uses automotive tools for proper assessment. This overview explains how it works to identify potential issues.
Get vidIQ to grow your channel faster! 🚀
https://vidiq.com/CharleysGarage
AI Generated·May contain errors
All right guys, in today's video we're going to talk about some turbocharger visual inspections,
diagnostics, things to look for. This turbocharger is off of a DT466 International Huey engine.
We got it removed and sitting here on the table just because it's easier to explain the stuff
where you can get a better view of it. But I highly recommend that some of the tests that
we're going to do, like the ones we're going to do with this dial indicator here, sometimes they're
better done on the actual engine where the turbocharger can't move around as much. So
obviously some of the things you want to do when you're inspecting a turbocharger
is when you take off the main outlet hose, you want to look for any kind of fluids inside of
these areas right here. Because the fluids that do go into a turbocharger should be restricted
to the middle of the turbo. There are seals that are supposed to prevent those fluids from getting
out here. So you definitely don't want to see any fluids here. You don't want to on the exhaust side
see any fluids in here. That would indicate that you have a failure of some sort and that's not a
good thing. So along with that you would want to inspect the housing. Check the housing for any
kind of cracks, signs of overheating, discoloration. Check the clamps that hold the sections on. You
got the clamp right here. Make sure that's not loose and not even backing off or something like
that. But visually another thing that you might want to look at is the actuator. Check the
condition of the harness. Check the pins and make sure they still look good. And then there's also
different tests. Some of them can be done on the computer or hooked up to a scan tool. Some of them
involve just disconnecting the rod from the actuator and doing what's called a bounce test.
I recommend reading the service manuals to find out which specific types of actuator tests you
can do on different types of turbos. All right so the part that you can't see is the condition of
the bushings and the bearings inside of this guy. And we check the condition of those bushings and
bearings by doing what's called an axial and radial play test. Radial play is pretty simple. The shaft
that runs through this turbo that connects this compressor wheel to the impeller wheel on
the exhaust side is supported by bushings that it rides through. And as those bushings start to wear
that means that that thing can move up and down or side to side. So we're talking when we say up
and down or side to side we're not talking about in and out. That's axial play. We're talking about
radial play. Radial play would be if this shaft can move this direction or this direction. All right
there are specs that you can find in service manuals where you take a specific size feeler
gauge and you put it between the blade and the housing and measure it that way. And those are
fine but I always find that kind of problematic in that most feeler gauges are flat and this is
rounded so it's not real super accurate in my opinion unless you get the rounded type feeler
gauges. But I like the way the Cummins manuals put it. They describe it as a test where you take your
thumb you grab a hold of this shaft and you just push it in one direction and then while holding
it in that direction you rotate it back and forth and you listen and you feel. If you hear scraping
or you can feel it rubbing then that's telling you you got worn out bushings in that turbo. It's time
either repair it or replace it. And then after you do radial play another check you can do is called
axial play. There's a thrust washer or some sort of thrust mechanism in most of these turbos that
keep the shaft from moving back and forth inside the housing too much. Just like you have crankshaft
in play and camshaft in play this thing has a certain amount of in play. The spec isn't going
to be zero because these turbos get extremely hot. And if you had zero in play the amount of
heat expansion that would occur would cause that shaft in these wheels to seize up in the turbo.
Definitely don't want that. So having zero in play is a bad thing. Probably worse than having
just a little too much in play would be. But we don't want to have too much in play because that
tells us that the thrust bearing is washing out. That's causing the other bushings to probably get
damaged. It's affecting the seals. If it hasn't failed already and the in play is excessive it's
not far from it. Alright so how do you check axial in play? You use the dial indicator. So what I'm
going to do is I'm going to take this shaft and I'm going to push it as far as I can back this
direction. Okay then I'm going to take my dial indicator and I'm going to put it on the end of
that shaft. Give myself a little bit of wiggle room so you can see the dial indicator is moving.
So I'll give it a little bit of play there. Then I'm going to turn my magnet on here so the base
doesn't move. And then I can come over here and I can zero it. So alright so I've got the dial
indicator zeroed. Now what I'm going to do is I'm going to go to the back side of the turbo
and I'm going to push it the other direction as hard as I can.
And on there I'm reading one thousandth of an inch. So one thousandth of an inch of in play
that might be in spec. I'm not exactly sure. I'd have to look it back up again. I think the spec
for this is about two to five thousandths. This thing's sitting on the table. This might have
moved a little bit. It's hard to say but I would say that I'm not too worried about it. It didn't
go way over so there's not a lot of thrust wear there. But I would probably do this test another
couple of times just to see if I can get it above a thousandth. The other thing I want to point out
is that the other previous video I did on camshafts and gear shaft gear assemblies and talked about
the dial indicator. A lot of people bought a dial indicator but there's some people telling me that
that was an expensive dial indicator. So I've searched around and found some other links
that I'll put in for some more affordable ones that are more kind of like this one. This one
looks fancy but it's not an expensive dial indicator and I'll try to find it put it in
the link for you guys. All right so I hope this helped you guys learn a little bit more about the
physical inspection and testing of the turbo. Maybe later on we'll get into some more of the
electronic testing and do calibrations and stuff. So thank you for watching guys!
