Rebuilding A Crystal Phonograph Cartridge With A Piezo Element - 1941 Philco Radio

Amateur Repair Time
257 followers
748 Video Views·Apr 20, 2025
This phonograph plays 78's and has that old, heavy tone arm that they all had in the 40's there for awhile. You can't get these Crystal cartridges anymore, the crystal inside deteriorates, so we're going to attempt to repair this one.
ladies and gentlemen welcome back to
Amateur Repair Time We've been working
for several weeks now on this Filco uh I
believe it's a
41602 So it's from 1941 that Craig uh
sent me This was his father Kermit's
radio And we've done a bunch of work on
it and got it playing again and fixed up
the cabinet a little bit Um it's
actually looking nice and presentable
But one thing that we haven't done
yet is work
on the
phonograph
Um you know that's kind of tough If you
don't work on the Well if you're
watching this video you probably work on
it too But uh if you don't work on them
you may not realize First of all it's a
78 player and it's the early 78 players
So there were two types basically There
was one that played with basically a big
steel needle
um that was good for the early 78s which
way I guess were all mono and then they
made one for the micro groove 78s to the
best of my knowledge at least that's how
it works and um this is one of the early
ones
1941 that's a little whiles back right
um and we haven't tested any of that yet
Let's see if we can get this thing to
work See if we can get it I mean we
won't get this to work but let's see if
we can get the radio to turn
on and we'll um we'll see if the
phonograph is I mean if the cartridge is
dead
Now a lot of these originally had
crystal cartridges The crystal rots away
inside of it
and stops working So to find any kind of
uh record player that had originally a
crystal
cartridge it's hard to pull that off
My question you know it's this scary
having the disease
So the way this thing is set up
if you volume volume is here and then if
you're in the middle it's off But if you
go to the left now you're on the
phonograph You can still hear the radio
signal a little bit because of the way
they amplified it They ran the the
cartridge through the other side of the
potentiometer Um and the output out the
middle of the
potentiometer Um so we're on the
phonograph now I don't have the motor
hooked up but Oh can you believe it you
just heard it people Can you believe it
when you pick up the arm the tone arm
there's a switch
here
Whoa That sounds interesting When you
pick up the tone arm there is a
switch The weight of the tone
arm pushes in the
switch So when you pick up the tone arm
it connects power to the motor which I
have disconnected right now
And another thing is the tone arm hangs
really weird It's
like it's not flat I don't I guess
that's just how they made
it Um but it sure sounded like that that
cartridge is working Let me turn it back
up The freaking cartridge works It must
be a
replacement Um you hear that though
[Music]
right the cartridge works That's
unbelievable I never would have thought
that So disregard everything I was
saying about the cartridge not being any
good It somebody's probably replaced it
Let's look Let's see if we can
see see if we can see what the hell's
going on with this
So I don't know what in the world that
is Oh maybe that's how you remove the
needle Yeah I haven't looked at this
needle
much That
needle is bent all to hell So see this
dust and green and crap on the cartridge
usually that destroys the cartridge but
this
one appears to still be all right So I
would assume you pull out on that knob
Maybe it screws out Can you see threads
down in
there if it would focus for
us So that must come out and then the
needle pops out The problem with a with
a these old 78 players is that you have
to change the
needle before every record That thing
being bent like that it shouldn't be
like that That's just been
bent by being abused I mean that's
not that's not how it's supposed to be
Let's see if we can see if there is
a I don't have the light right but let's
see if we can see if there's a thread
there
It's all that green Usually that eats
the the the cartridge up but not in this
case Or maybe it's just grabbing I don't
know I was touching the needle and I
hummed Yeah I don't know Okay let me see
if I can turn that by hand with both
hands and see if I can get that old
needle out of there Yeah I can't turn it
Um it's knurled though like where you
know where you can get a grip on it but
I can't get it to come loose So what I'm
going to do is I'm going to put a little
oil on it and let it sit for a while And
then we'll come back to it after
hopefully the oil's kind of penetrated
in it And then if I have to I can turn
it with a a pair of pliers or something
but I I hate to break that off If I
break that off I won't be able to get
that little piece out of there very
easily I would you know it's working I
would love to just take that out put a
new needle in it and roll with it And
then we can work on the motor Um if the
Yeah we could take it out and and look
at it and everything
but a working
uh a working cartridge in this old uh
setup is not something that's easily
replaceable I thought we were going to
have to do all kinds of crap to to uh
take the cartridge apart and everything
else but I think we might get lucky
Yeah So let me soak it in some oil and
then we'll try to get that old needle
out of there All right folks So I have
let it soak for like two days and I
can't get that thing to turn by hand So
I'm going to have to force it and uh
hopefully it won't break it So I'm going
to put some I'm going to use some pliers
and I'm gonna wrap this around the
pliers so that hopefully it won't mar up
that little thing My understanding is
that twists out and then you put a new
needle in and then twist it back in
That's how my photograph my old school
from the 20s photographs are So
hopefully I don't break the thing I'll
try not to force it but I got to give it
a little pressure All right it came
right out
So I'm going to put a little more oil on
it before I put it back
in And here is the needle That does
appear to just be a nail you know a a uh
photograph nail or whatever I don't know
It's awful
flat What's going on here is that
supposed to be like
that i guess I should look this up and
just
see You know I use the one use nails I
call them nails They're not really nails
but I use the the uh the one use ones
where you change them after every record
They're not that expensive They're
really cheap And I don't know that it's
supposed to be bent like that but it
sure does look like it was manufactured
that way because of that See how
it's flat right there so this damn thing
might be supposed to be like that I
don't know
What do you
think if I put a regular one in it's
going to go just
straight
Hm I wonder if it was some kind of like
upgrade or something where they stopped
using the ones that were just But the
the problem is the tip of it gets all
screwed up and it'll just eat your
records up if you don't put a new one in
there Let me do a little research I've
I've looked at the uh manual or the
little paperwork you know online about
it and they don't say anything about the
needle or the
cartridge
[Music]
Um so I'll see if maybe I can
well I don't know Maybe I can find some
more pictures of a similar
model and see what they've got in there
I don't I don't know I guess worst case
we can just put the thing I'm talking
about in there All right folks So
sometimes if you search around long
enough you find what you want to find
Look at this Apparently way back in the
day they marketed a needle that they
called
uh an arrow point coin machine
needle Longer life The needle lasts
longer Records last longer Now look it's
that same freaking needle See the little
bend in it and everything
It's kind of interesting that they've
moved it off center Why did they do that
did they think that that would
uh kind of counterbalance the weight and
make it a little lighter on the record
or something that's
interesting So basically this was
marketed as a replacement for the
standard steel needles that you just
throw away You're only supposed to play
like one record with
Um so this thing of of course is
certainly worn out by now but I was just
wondering if that was a special needle
for that Filco It's not It looks like if
you went to the store to buy more
needles uh you could just pick this up
at the same time and it supposedly would
last longer So they probably did that a
long time
ago So I can get rid of that and just
put regular needles in it Now we know
Here's another one that Filco themselves
actually marketed It's a Filco ruby
needle I think maybe it actually had a
uh jewel on the tip of it or something I
don't think that's the one we've got
though Okay so I've done some work on
the back here First I put a connector on
the antenna cuz they had it just
soldered to the side here And there was
a problem where if you watch the first
video and the second video and the third
video uh this had been all ripped up and
they had stapled this and broke wires
and stuff So I had to solder some stuff
back together and all of that And so I
just poured glue all over this on a
previous video to make it hard as a rock
And it it's holding up really nice So
it's very solid I like that Uh but the
main problem is that every time or any
time that you would have to remove the
chassis you had to unsolder those And I
think that have been part of the reason
that it was all screwed up These were
these are obviously replacement wires at
some point right so what I've done is I
put a connector here so that it can
easily be
disconnected
Now I'm I've got two So you run into the
problem where you don't want to make it
where people down the road 50 years from
now plug the wrong ones in and screw it
blow something
up right so what I and even
worse these two wires are coming right
off the AC inside the set because it's
what powers the phonograph So I need
those and I need the antenna Well if you
accidentally plug the two AC wires into
the antenna the antenna is just a short
like a loop You would be plugging both
sides of the power together and blow
something
up And if you accidentally plug the AC
wires into the antenna wires into the
radio that probably wouldn't be good
either So you got it Now if you plug the
motor that it doesn't have any power
into the antenna that doesn't have any
power that wouldn't really be a problem
But so what I did was I um I put
two the two uh male
plugs coming off the radio So they can't
be plugged into each other Um so that
gets rid of the instance where the ant
the power could be plugged into the
antenna in the radio but you can still
plug this one into this one So what I
did was I
reversed one of the pins inside so that
it's keyed different So like I put like
the female pin in the male part and then
the male pin and the female part so that
it'll only plug in to this connector
It's keyed If you try to plug it into
this connector it won't go And you know
they're the same exact color So
hopefully But then again over here
they're not the same exact color One of
the colors is different
Look folks It was the best I could do
All right And this is the across the
line cap I figured I'd just put it out
here since I
could So we had a little noise in the
radio
Uh people are telling me it's switch
mode power supply switching power supply
noise I'm not so sure about that
folks I mean what do I know but I got
some radios that that it does it some
radios that doesn't So it's hard for me
to believe that there's something in my
house making it do that So if you turn
off everything in the house it still
does it I don't have hardly anything
turned on right now I got a few lights
If I turn off all the lights it still
does
it Um so then whenever you tell people
that they go "Oh it's your neighbor."
Well if it's my neighbor then you know
whatever Why am I turning off my lights
if it's the neighbor i don't believe any
of that I think that can be a deal but I
don't think that's the deal with what we
got going on That's just my opinion
man Okay so uh I've got the So now I
need to be have the balls to turn it on
and see if I blow something
up because the photograph now the the
motor now has
power And also we're doing the little
trick thing with the with the uh the cap
Now if you don't get why I put that out
there it's so I don't have to take the
chassis all the way back out On the
previous one we just didn't put this in
It's a safety cap too You have to put a
certain cap in Um so where it was in the
cabinet was right
here So it would be safer to mount it
right from here to here so that it's
switched off or else if you left this
thing plugged in that cap would always
have power on it if it ever shorted or
something Big problems Uh but it's a
safety cap so it shouldn't shorten So
what I've done is instead of moving
it right
here I've just moved it right here which
is electrically the same thing folks
It's the same thing You know it's the
same thing It's just it's outside of the
chassis I mean and you could argue oh if
you touch it you'll get zapped Well if
you touch these wires you could get
zapped Don't worry about getting zapped
It's going to be fine Don't touch that
remote Don't touch nothing while it's
plugged in That's the obvious
answer I don't know why all of y'all
want to touch things when they're
plugged in I don't do that Look back on
my videos I hardly ever touch the thing
if it's plugged in So I don't worry
about an isolation transformer and all
of that crap cuz I'm not touching it
when it's plugged in It's a good way to
get the hell shocked out of you Okay So
um I'm going to I'm going to leave it
like this Actually we'll leave it like
this and plug it in and then um see if
anything explodes whenever I turn it on
All right I plugged it in Now I'm going
to turn the radio back
on which if the switch is bad it would
make the phongraph turntable immediately
come
on I don't know if I've got it on the
channel or not You would think I
would but since I've got it backwards
now the reception it might not be tuned
in There we go Bonus episode where we
answer the questions that are on your
mind Make sure to spend your Tuesdays
and Thursdays with Trey Subscribe now at
foxnewodcast.com or wherever you
download podcast Hope to see you
America's listening to Fox News Eric and
Lyall Menendez's bid for shorter
sentences and a shot at freedom is
delayed again A hearing now set for May
9th where the judge will consider the
defense's motion to recuse LA County
District Attorney Nathan Hawkman from
the case to violate what was well that
that across the line cap got rid of most
of it didn't it listen to the humos
0622 Okay So we'll mess with that when
we get it turned back around Okay So I'm
going to turn it off and I'm going to
turn it over to the photograph
side All right So that's the photograph
side Now I think on either
side all you're doing when you do that
is uh let me show you the
schematics So I have turned it
from we were just turning it on this
side Do I have that right yeah
So it's getting the out
[Music]
Uh I can't ever track
this So here's the
grid connected to the center of the the
U volume control
right and if you look the
pickup connects to here So we were up on
this side We have now turned it over to
this side
Oh okay Yeah So here's what's going on
So this goes through the volume
control and into the grid Is that right
are we doing it
properly and now since we've got it on
this side this goes in it and into the
grid Well that can't be right because
the signal wouldn't go through Anyway
you get the whole point I'm sure some of
y'all can tell We've got this actually
No it's got to be on that Okay So anyway
so that's how it works It's a
centertapped two-sided
[Music]
um volume control basically Boy she's
noisy as hell on the phonograph side but
I think I've got it way up If you tune
it into a channel you can still hear the
channel coming through So whenever you
play the phonograph you might want to
tune it off of a channel Tune it to a
quiet spot on the ch on the uh radio and
then play the phonograph so you won't
get all this
crap Hear that
[Music]
So it's a very noisy design but I do
have it turned all the way up
too Okay So let's turn it around and see
if the switch works And the photograph
motor will turn Okay So we've got it
turned over on the phonograph
side And when you lift this it's going
to lift off of
that little
uh platform there and it should turn on
the phonograph motor I I think the
chances of that working are about 10%
That's what I think But let's
see Oh ye of little faith Of course it's
working That's nuts I can't believe that
That's going to be noisy as hell
Well it's time for a record
folks Let me go get a record that I
definitely don't care about and then
we'll try it All right I'm almost afraid
to try it That needle I mean I put a
brand new needle in it but that that
cartridge is just almost impossible for
me to believe that that thing still
works But let's see Here we
go Boy this is a weird tone arm too
all that I think the cartridge is dead
The humming is from where I was near the
wires I guess I was touching the the
case of the
cartridge and that's connected to like
one of the grounds
I mean you can hear it but I don't think
it's amplified at
all It's pretty cool though
[Music]
Is it eating the record
[Music]
up i think it's just cleaning the record
pores All right So how are we going to
fix it well I'm going to take the
cartridge out I'm going to tear it apart
and see if we can uh replace the inside
of the
cartridge with something that'll make
noise So just for giggles I put the old
needle in just to make sure it wasn't
like a uh angle problem or something but
no it's just
cartridge is
dead It's
baked Okay so after removing it you can
see the futility of the futility of even
attempting to use that thing There's no
way that was going to
work Look at
that We had to try though right
so one of these
is well I don't know I don't know if one
of them's connected to ground or not but
the whole thing
is when I was touching this it was
humming It wasn't that I was touching
the needle It was just the when I was
getting near it it was So I assumed that
that meant that it was reproducing the
sound It wasn't It was just like a
ground problem
So this sucker has seen better
days Part number Is that what that says
part Sometimes if I zoom in I can see it
better Let's see
It's just so corroded you can't
tell All right So I'm going to attempt
to use this I don't
know So the the whole deal is this is a
crystal cartridge So these put out like
3 volts or something like that And so
the set is designed around it wants 3
volts to go into that um volume
pot So what happens is if you put
something in here that doesn't give you
3 volts or if you put a cartridge in
that doesn't give you 3 volts if you can
get it to mount you know um it'll be so
quiet that you can barely hear it So
it'll be probably a little better than
it is now cuz right now all we're
hearing is needle noise We're not
hearing anything get amplified
Um but um
yeah so you got to put something in here
and then see if it's loud enough And if
it's not you need to build a little
preamp in the circuit to
um beef it
up So I think I'm going to try to put
one of those PZO Po
uh reproducers in
it And then we'll see if that's loud
enough that you can hear it And if it's
not we'll see what we can do about
making a little preamp
circuit But I think I can put it in this
housing I've seen some videos on YouTube
of other people doing it I think I can
put it in this housing to replace what's
in
here And uh we'll go from there
So first step is I need to drill out
these three rivets that hold it together
This one that one and this
one And then that will get me into the
thing And we can take it all apart clean
it up take all the junk out of the
middle of
it All right folks We drilled the rivets
out I think
so So here's what's left of inside
You think that was
needed is that a necessary
part okay So here's the bottom So I saw
a video on YouTube or a gentleman fixed
one of these the way that I'm going to
do it
So this thing has rubber rings right
there and right there that are all
destroyed And then it's
grabbing a little something that
connects to the actual crystal back
here And then
these were embedded in the
crystal So that's what's left of the
crystal So that's why our cartridge
doesn't work Um might have something to
do with this being the connection So you
know it's kind of a bad
connection So that's what I was saying
The chances of it working are like one
out of 100 or something like that This
ain't it This is one of the
99 Wow what a mess All right let me see
if I can clean this up a little bit See
what's
salvageable Okay so we drilled out the
rivets and this is what we came up with
I'm going to put these through my
um what do you call ultrasonic cleaner
and clean it up You see just how
corroded it is We saw that from the
outside So there is a little indention
in here that there was a little piece of
rubber in It's like a
damper so that the crystal rested on it
but you can see the little indention The
crystal rested on it but it still had to
it was supposed to move a little
bit All right Um and then here's the
other
side Same thing There was a little piece
of rubber in
there to kind of protect the crystal Now
remember all of this stuff is 80 years
old
84 years
old And
then this was in the
back These two little
wires were attached to the crystal
The
crystal
had a little piece of cardboard or
something wrapped around
it or a piece of rubber or
something that slid into
there to hold
it And then this
had little rubber rings right there and
right
there to separate
it from the
case and it was
like I might have it upside down but it
was like
that So
basically you don't want
this or this touching the frame So we
need to wrap this We need to clean all
this up We need to wrap this in rubber
and wrap this in rubber so that it is
suspended and not touching either side
Boy that's awful tight
though It's going to be hard for that
Yeah I guess if you just get it just
right it won't
touch either side
there And then on the top or which is
actually the
bottom that doesn't actually touch
it So same thing We got to get the
rubber where it's just in there just
right And then back
here I'm going to put some rubber
there No not
rubber
Well it's a vibration thing so I guess
it could be
rubber We're going to connect it to one
of these
PZO elements
Now I took one and busted it all
up to show you You got to be kind of
careful with them But all these are is
it's one
piece and then a second piece and the
wire is soldered If you look at a new
one the wire is soldered to that So it's
kind of the same thing It's just a
different um the crystal
um worked better than this probably
will The crystal is probably going to
put out more voltage and be louder This
probably isn't going to be as loud but
we'll mess with it and see And also
since we've got so much upside on the
volume on that
uh record player and just the way the
circuit's designed I think it might be
all right We may not need a preamp I
don't know but we'll try it
So next up I got to clean this Get it
looking a lot better And then I've got
some tape here I'm wondering if my buddy
Dennis gave me this It's pretty thin
though But I wonder if this would be
good I've got some thicker stuff
somewhere too But I wonder if this would
be good to cut into strips and to create
those little rubber
things Um I'm I'm reading online where
people have been doing it Of course I
didn't come up with this idea Um but
other people are saying that you don't
want to use rubber bands because it the
rubber dries after a while and just
screws you all up But this works pretty
good Um they said but this is thinner So
they like using stuff like a silicone
glove or
something Um but I think I'm going to
see that cuz this stuff has adhesive on
it too So I think I'm going to see if I
can just cut
this I don't know though It might not
work cuz I I don't know that I can get
this backing
off I'll mess with it If I don't use
this I might have some other stuff I can
use I've got this Gorilla Glue tape too
but I think that's too
thick I don't know Maybe not Maybe
that'd be
better What do you
think you can't really tell can you
maybe this would be better
Just
one revolution of
that Yeah maybe that would work All
right So that and then we're going
to have to get it to grab the PZO
tweeter after we cut
it I won't use this one It's screwed up
obviously it We'll cut part of
it maybe this
way and then uh make it the size to go
in there and leave room to solder
the connections to the wires and blah
blah blah But next step is I need to try
to clean all this stuff up Okay so
here's how it ended up after going
through the ultrasonic cleaner You saw
it was in pretty rough shapes and it the
cleaner I don't know if I left it in
there too long or what but it took all
the plating off So now we just have it's
copper I guess Sure looks like penny
copper to
me Um but it's pretty clean which is all
I really was going
for The residue of all the old rubber's
gone I think we're going to have to
drill that rivet completely out
Um so it's all pretty clean
now Not perfect but hey it's 80 years
old I think we can roll with it And the
screw isn't stuck anymore It now easily
removes And it cleaned up our posts
which is
good So um we're going to roll with that
It's probably as good as I can get it
All right So I think next we'll see
Originally that rivet didn't go all the
way through You could just use tape to
hold it together whenever you put it
back together But I think because of the
way this
mounts the wires go around it around
that post
So I think as long as I don't run that
that
um whatever the paso switch or read
switch whatever paso sensor all the way
back and I've got new wires that run
around it and don't touch that I think
we'll be fine to uh I mean it's going to
be there anyway but I'm going to try to
drill a hole straight through it so that
we can try to put a rivet in it whenever
we're done after we test it a little bit
Okay So uh I'm going to do that And then
we need to wrap a little bit of
something around these two little
bushings here to put it in there All
right So I used a little bit of this but
it was too thick so I stretched it a
little bit And then I used some of this
tape and that worked too but it's too
thin So I had to go around several times
and it's kind of you know bud is a big
mess So if you check I'm trying to make
it where
that the pickup is isolated from the
cartridge
So we got you know from that we have
connectivity but if you try to connect
to the from the body to the
pickup it is not connected So that's how
you want it So we've got it suspended in
there with little pieces of rubber
basically So let me open it back up And
now we have to cut the
PZO Okay So I have cut the little PZO
thing down I just cut it on the end
that's got the wires facing
back Right And
then I took a little bit of
my Gorilla tape and wrapped it around
the end And that was thick enough for it
to kind of this thing to to kind of
pinch it It's holding it really
good And then I soldered it to the
little pins on the
back Nothing's touching metal anywhere
Um I guess I need to watch that one to
make
sure Uh I put a little piece of rubber
underneath
the pazo And people if I'm not
pronouncing it right I'm never going to
pronounce it right You can tell me how
it's pronounced all you want I'm still
not going to do it right Um I put a
little piece of rubber under that so
that it won't it can't touch the body
And then I've got one in here as well
And that originally it had that you know
but these are just all dried
out Um
so rubber
tape tape which actually kind of made a
mess but that's all right
Rubber PZO cut down real small two wires
soldered to the connectors rubber under
it and rubber on top of it So I'm going
to put it all back together And then I'm
going to check both of these pins to see
if either one of them's connected to the
case And I'm going to check this to make
sure it's still isolated from the case
And then if that's fine what I'm going
to do is I'm going to put some tape
around it just to hold it together We'll
mount it back in the record player and
see if it works And if it works we'll
leave it I've heard you can make this
The bigger you make this the more volume
you get out of
it I don't know I've I've read some
people have luck with it some people
don't I think if you're using it in one
of those like um one tube wonders it
doesn't work But I think if you're using
it in a in a radio phongraph I think it
very well may work because the radio you
know has a pretty healthy amp built into
it That's my theory at least So we'll
see So I'm going to put back there and
next step we'll try it in the uh in the
photograph All right So we're just
getting a humming sound If I check the
continuity I've unwrapped all this If I
check the continuity between the two
wires of the pickup though they're
shorted and it's because the wire is
deteriorated and the ground wire is
touching the signal
[Music]
wire right here at the end of the plug
So I'm going to clean all this up get
this dressed and then wrap the ground
back around and solder it to the side
And hopefully that will keep those two
separate and then we'll be good to go
Okay folks So I removed the whole tone
arm and I replaced the pickup wire with
some speaker wire Um
if like an RCA cable or something might
be better because it would be more
shielded I don't even know if that's
shielded at all but this thing's going
to be so noisy The idler wheels all
screwed up and everything If we get it
to work it's going to be so noisy it
won't even matter So um I was able to
reuse the end that goes in there and
then I was able to resolder the two
pieces that go on the on the uh um
cartridge There is a plastic or
rubber something I don't know what this
was maybe felt or something There is a
round bushing that mounts under the tone
arm where it meets the wood And then
there's another one on the top that
mounts above the tone arm where it meets
the wood
And uh there's a rubber
bushing around that too All of that fell
apart The rubber
bushing was all right but the rest of it
you can see the pieces of it laying
there But it's mounted back in there
nice and firm That's probably another
noise thing so it's probably going to
make it even
noisier But you know we're not really or
I'm not really going for high fidelity
on this And u we're learning So if we
are able to rebuild this uh tone arm or
this cartridge you know on the next one
maybe I can do it a little better On the
next one maybe I can do a little better
on the next one Maybe I can do a little
better I've been wanting to try one of
these for a while Um you can put a
ceramic more modern cartridge in it But
the problem is
um the tone arm is just it weighs a ton
on these So those things want like four
grams tracking pressure or something
This thing's
like like half a pound or something I
mean it's heavy Really heavy on that Um
and it's using a steel needle so it's
just you know that's how they were
designed So anyway let's uh put it back
together and uh let's see if the thing
works Hopefully that cartridge will get
some tone out of it All right folks So I
have turned it on
Little bit of a
hum Let's see if it wants to cooperate
Come on
baby I'm trying to help you now Come on
now Boy that thing's moving fast isn't
it
[Music]
that's not real loud but
to go
[Music]
through and I'd much ra
[Music]
So that's all it's got
[Music]
but it's definitely amplifying it
So if you've got an old one of these
heavy arm 78 players
uh you can rebuild your your cartridge
like that and it's pretty inexpensive
I mean I spent about three bucks
[Music]
I wonder if this is going to be
copyright stricken and I have to redo
this whole thing
[Music]
through that could mean another fight on
[Music]
and I will come back But what good will
it do
fantastic I love it Let's see I think
we're still on that other channel too
Let me go off that channel and see if
that changes the volume
We are born a certain way here and we
say I could blame you but
doesn't seem like there's any cross talk
between the radio and
it matter of fact when I was hearing
that before I wonder if that might have
been because the
um I wonder if that might have been
because the uh the the pickup was
grounded to to
itself
Interesting Let's see what this record
is Let's see if it's going to get
me I don't want to say their name I
don't know It might copyright strike
me We'll
see I really you should change the
needle after every record but we're
testing this old beat up record
[Music]
boat A cleaner record um I think would
probably sound even
[Music]
better And I think if we isolated the
tone arm a little better with the rubber
mounts you get rid of some of that noise
A new idler wheel would get rid of the
turntable
noise So there you go folks Let me know
what you think Hope you enjoyed it Craig
thank you for sending me this buddy It's
a pleasure to work on it I'll take care
of it See y'all on the next video Now if
you like watching these old uh uh these
old radios and record players check out
this video
I'm going
