First Signs Of Life! HV And The RF Section - 1953 G E 17t5 TV Repair Part 5

Amateur Repair Time
257 followers
653 Video Views·Sep 27, 2026
Check out our Patreon page, for all of our channels. Contains outakes, concise arcade repair tips, bloopers, repair FAILS, Audio youtube wouldn't allow us to upload, and much more!
https://patreon.com/JoesClassicVideoGames
------------------------------------------------------------------------------------
Ladies and gentlemen, welcome back to Amateur Repair Time. Now in our previous video,
we have been working on this General Electric 17T5 1953 television set. And on our previous video,
we worked on the vertical section and at the end of the video, we fired the sucker up just to see
what was going on with our B+. B plus is looking pretty good. It's going to be a little bit high
because we're only at like 109 volts instead of 120. I just stopped it at 235 because that's
where it's supposed to be. It seems like all of our tubes are aglow with the exception of
one of them. The CRT does have net glow and it's a series string set so everything's getting
power. We were under the assumption that some of these tubes might have been bad,
but I don't know, whatever. We got it to fire up. I guess last time when I didn't have the B
plus hooked up, I had something disconnected that needed to be connected whenever we worked on the
power supply. So we did one video where we went and got the thing and then we checked it all out.
We did one video where we worked on the power supply, that may have been the same video,
I can't remember, where we basically worked on the B plus supply and got that all recapped where
needed it and replaced all resistors that were out of tolerance and worked through it.
And while we're going along, I am reading through this. Look at this beautiful thing.
Practical Radio Television. This belonged to Mr. W. E. Raines Jr.
That's from the National Radio Institute in Washington, D.C. and it was a mail order
TV repair course from 1951. So we've been reading through that a little bit as we go,
just to kind of understand the circuits as we go. So we did one on the power supply,
we did one on the horizontal section of the horizontal deflection basically of the television.
We did one on the vertical, that was last time. That leaves us with sync, the video, the sound,
and the RF, the antenna section. And we kind of have been hitting around on the high voltage
section. Now the TV is up, but there is no image or nothing, no raster on the CRT because I don't
believe it has high voltage. Let's do the old hand check. You don't think I'll get shocked right here
on video, do you? Yeah, there's no high voltage at all. We've got our B plus. This set is pulling
about one amp of current through it right now. We've got the brightness turned all the way up.
If I turn up the volume, the audio amp appears to be working. But let me show you the problem
that it appears we have. It's the horizontal output tube, it's the damper tube, and then
we're getting nothing over here. So this is the high voltage rectifier tube and it is dead. I
don't see a thing on the filament. You're seeing some orange and red there. You're just seeing the
test probe bleed on the other side. There is no glow coming out of the high voltage damper tube,
or high voltage rectifier tube. The damper tube doesn't have filament glow. Now we did not check,
or did we check? Did we check the high voltage rectifier tube? I can't remember. I'll have to
go back and watch my own video. Look, I've got a little check mark beside it as if we did check it.
I remember taking it out. But here's the deal, Lucille. If you look at this rectifier tube, it
works different than all of the other tubes, every single one of them, including the CRT.
This is a series string set, so all of the filaments of the tubes are connected together.
And their picture tube is right there at the end.
So the reason they do that is because it's just how they're wired. It's so they don't
have to use a transformer to give all the different voltages for all the different tubes.
They've got all of these tubes in a row, along with these little inductors and things,
and that adds up to 117 or so volts. And then if you look in parallel, they have another one,
another string, and those add up to 117 volts. Or maybe a little shy because
they've still got to run through the picture tube, but whatever.
Okay, so you've got, it appears 300 milliamps of current running through this, and 300 milliamps
of current running through this, and then 600 milliamps of current running through the picture
tube, right? So all of these little capacitors and things are just bypass capacitors. They're
used to do filtering and stuff so that you don't couple interference to the wrong tube.
So if you had, I think the way it works is if you had the audio tube and it's got audio
running through it, you don't want to put it into the vertical tube where the tube signals
would crosstalk. So they've got all these little capacitors to filter stuff out,
which is shielding basically. Okay, so the only tube that's not on here is the high voltage
rectifier tube, because it gets its filament voltage from a different place. So if you look
down there on the bottom of the tube, it shows the filaments, and it runs through C, what does
which is a 500 picofarad capacitor, and it's coming off this winding of the flyback. And then
on the other side, you've got a 1.2 ohm resistor coming off this other winding, and then that
winding runs through this line over to the anode cup. Okay, now that says that it's got a resistor
there, which it says is R116. But that wouldn't, that line in particular wouldn't have anything to
do with us seeing filament voltage, you know, just a glow. And that line I haven't been able to check
because I didn't remove the anode yet, the anode cup. And I also haven't been able to check this
1.2 ohm one. In that spot down in there, there's not a bunch of room to get down in there and
test stuff. There's a resistor coming from here to here, but it's all covered up and insulated,
so you can't really test it. I'm gonna have to get at that again just to tell for sure.
So I think our problem is going to be either the socket or that resistor right there is burnt up.
Could be this capacitor is burnt up. So we got something like that going on.
So with no high voltage, yeah, you're not going to get any picture.
So today we're going to mess with that a little bit, and we're also going to work through this
video section. If I can find the other page. Here we go. Here we go. So we worked all this.
That's the horizontal. We worked all this. That's the vertical. Now we're up to the video stage.
And we've been cleaning up the chassis as we go, of course, by getting rid of the big
wax caps and putting in new tinier ones to give us a little more room to work on stuff.
All right, so let's get into it. I think, I guess the most interesting thing would be to try to work
on this first and see what we've got going on. So I took the high voltage cover off. So there's
three things, four things that I need to check. One is this cap on the hot.
Notice it's burnt a little bit. It's not making the greatest of contact either.
I don't know if you can see in there, but all that is not great. I noticed that whenever we
were messing with it before. So I've got to figure out what to do about that. I don't have much
play. There is a little bit of play. I guess I could just replace the whole wire.
I mean, it's soldered in there. I could desolder that and put a whole new wire. That'd probably
be the best thing. I don't know if I've got... Yeah, look, it's just barely connected in there.
Look at that. So that's probably our issue right there. This is probably doing what it's doing,
but it's not powering the flyback. So maybe we do just that first. So that needs to get handled.
So that's one thing. The second thing is this resistor is questionable. This one seems to be
the one that keeps the current low on the tubes whenever the set's warming up. This one's
questionable though. But now that I got the cover off, I can measure all this better and clean it
up a little bit. So we know all three tubes are good. The flyback is probably good. I mean,
everything seems all right. But now that I can get to these connections,
I can check those other windings that I wasn't able to check before.
They're called out on the schematic so you can see if the resistance is proper.
This over here looks fine. So we've got one, two, three. I don't think the flyback's gonna be the
problem. I hope not because that would be the hardest thing to fix. And then you've got a
resistor in lead from here to here on the filament like we were seeing. And then you've
got this wire that is the anode cup wire, which all needs to be cleaned up. And I can check the
resistance on that because it's also mentioned in the schematic. So I'm going to work through
some of it and we'll see what we can figure out. Okay, so I started working through it a little
bit. This resistor, we may not be able to test in circuit because I'm not getting 4k. I'm getting
way higher than 4k or it could just be burn up. So it's this white one. I cleaned it up a little
bit. I cannot get a good reading on that. We're talking more like 60k, but sometimes that's
because it's connected directly to a cap, for instance, which it is. So we'll see. We got to
mess with that. Now you would think that it wouldn't work like that, but it does. The number
just keeps rising. So I don't know. So that's questionable. So what I'm going to do is I'm
going to clip the meter to it right here and see if we got 235 volts. I don't know what this voltage
is supposed to be, but we'll see if there's any voltage there or if it's really low. I mean,
if it's two volts or something, we'll know that that's the problem. Okay. We clean this all up,
which should feed to, I guess this is the primary of the flyback. Okay. The connection from here
to here, actually I'm testing all the way over to the tube is correct. And then from here to
here is correct. And then the connection from here to here is correct. And from here to here
is correct. This connection, I don't know what that is. I'm missing a wire. I mean,
I can't find it. So I don't know what that is. This one is the, like, for instance,
this connection here isn't there. So underneath maybe I need to turn the setback over,
but underneath maybe there's a cap and somehow it ties in the flyback again. Although,
I mean, there's only a certain number of wires in the flyback and there ain't enough wires. So
I don't understand something. So this is questionable, but you know, everything else
on the flyback test out fine. So I would think it's all right. Now I don't like all of the
goo that I see underneath it, which typically means it got really hot, but maybe they all do
that. And we already did all of this. So I think we're down to two problems. This resistor could
be fried. We fixed this connection was probably bad. Oh, other thing. I was able to take the
cup off, cleaned it all up and then tested from here to here. And it's supposed to be 470K. I
got 445K. So that's good. And I was able to test from here to here. I got 1.3, I think 1.3 Ohms,
whatever. So this is correct. The only thing that's a question mark is this and this. So
what I think is going to happen, I think there's a 70% chance whenever we turn it on this time that
it powers up the screen because I think that you saw how bad that connection was. It was horrible.
All right, folks, let's see what we get. Okay. So I've got it hooked up to the B plus
and we're just shooting for 235. We did this on the previous video and we got it up to where it
was drawing a little over an amp. So right now it's at 225, but what's going on is this warming
up. It'll drop back down. We're not even at a hundred volts yet. So now we're at basically a
hundred volts. B plus is at 235. And by the way, the B plus doesn't have to be exact, but we're
just using it to try to watch to make sure that the amps don't jump really high and seeing what
we're working with. When we get to 120, which is what it'll operate at or 125 or something,
we'll probably, the B plus will probably be much higher. So 220. Oh, I think we did it.
That's where the B plus wants to be. Let's see where that puts our volts. We're at one amp.
We're at 104 or something like that. It appears we have high voltage. I have never seen
one of these old tube based analog TVs boot up. Well, I like that. I've seen this before in them,
how it like has that on the corners. I don't know what that's all about,
but I've seen people when they're finished, like sell them like that. So I don't know if that's
supposed to do that or if that's just because we don't have the video section done and we don't
have a video signal in. Okay. Well, we got our high voltage and by the way, this one tube is
glowing like a freaking Christmas tree bulb. I don't know if that's correct or not. It could
just be that that tube is very bright. 233. All we're trying to do is see if the high voltage is
working and it is. So I think that's good enough for that. We don't need to keep trying to mess
with it. Okay. So we've done the power supply. All of our string obviously is working. We've
done the horizontal output. I mean the horizontal deflection. We've done the vertical deflection.
I guess it's more properly referred to as horizontal sweep, vertical sweep circuits.
We need to do the video circuit, the audio circuit and the antenna circuit, the RF circuit
and then troubleshoot stuff. So let's get into the video section. Okay, folks. So I changed my
mind. We could do the video section, but I think we're going to do the RF section where the signal
comes in because it's going to basically describe what happens from the signal up to that section
and it'll tell us how it gets split apart. So that's basically in order, right? I think we
did this in order. We did the power supply and then horizontal and then vertical and now we're
on RF and then we'll do video and then audio last. Okay. So changed my mind. So here we go.
So this is Practical Radio Television, a 1951 course. It says Pioneer Home Study Radio School,
National Radio Institute, Washington DC. And this is in book number 50. This particular one is
actually 1950 and it is called Basic TV Receiver Circuits, 50 RH2. Okay. You have previously
studied in block form the various sections of a TV set. We kind of did. And have learned something
about the functions performed by the TV receiver stages and sections. In this lesson, you will get
acquainted with typical TV circuits and their operation. You will not have to cover all the
variations in the circuit used by different manufacturers because each section of a TV
set will be treated in detail elsewhere. So there is a whole book on just the RF section,
but I mean, it would take us hours and hours to read it. So I'm just reading this because it's
like a nice little overview. Let me see if I can find it and I'll tell you what it's actually called.
So that book is 52 RH2 TV Input Tuners. And it's about 30 pages that goes into deep detail on just
the input, the RF stage. And I mean, it's on and on and on. It tells you exactly what's going on
and exactly what happens everywhere. We're not going to go through all that though.
We're just going to do the basics. Now you will build the foundation for this future study by
covering only the fundamentals of television circuits, the input tuner. This section of a
TV receiver is also commonly called the front end or head end of the receiver. Okay. That makes sense
to me. They're calling it receiver. And so to me, if something's a receiver, the front of that would
be where it receives it. So that makes sense. It contains the RF amplifier and the local oscillator
mixer first detector. The first section of the front end is the RF amplifier. This section
increases the amplitude of both the sound and the video RF channels signals without changing their
characteristics in any way. And hence must have a pass band of at least six mega cycles. In addition
to this, the RF amplifier must give some rejection of carrier frequencies outside the desired channel
that might cause interference. The amplified video and sound RF signals are fed into the
mixer first detector section where they are combined with the unmodulated RF signal that
is produced by the local oscillator. As a result, two IF modulated carrier signals are produced.
One is the sound IF carrier and the other is the picture IF carrier. Various IF values ranging from
12 to 25 mega cycles have been used, but higher IF values in the vicinity of 40 mega cycles are
becoming more popular since this gives the RF amplifier a better chance to reject signals that
can produce image interference. Now, ours was built in 1953 and this book is from 1950.
So you can imagine that's probably what's going on with ours. I don't know.
The RF amplifier. The RF amplifier has three important functions. Since it is between the
mixer and the antenna, it reduces radiation from the local oscillator. The local oscillator,
if the RF stage were not used, would radiate energy from the TV antenna that might be picked
up in a nearby TV set and cause considerable interference. So that's interesting.
The RF amplifier increases the signal strength on the desired TV channel. This gives a better
signal to noise ratio in the TV set. The response of the RF amplifier should be broad enough so that
it does not cut off any of the desired signals. However, equal amplification of the TV signals
is generally not obtained, but this may be made up for in other stages of the receiver by increasing
the amplification of the signals that are slighted in the RF amplifier. So I think that's the AGC
circuit, which is similar to the... I think it's called AGC in the radios too,
automatic gain control, whatever, where it basically amplifies weaker signals and
curls off higher signals, or I think it does. It might just amplify the weaker ones.
A lot of the stuff I work on doesn't even have that, because I keep working on really cheap
radios that just don't have it involved, or stuff that's so old that they didn't do it,
like that Atwater Kent we did didn't even have that section, I don't believe, and that Grigsby
Grinnell Majestic set that we did, I know didn't have it because it was too early.
The RF amplifier must also give some degree of selectivity, and it should reject image signals
that create interference with the desired station. I have that problem all the time on radios,
where you get all kinds of crosstalk, and it's not really selective.
The selectivity of a TV RF amplifier, however, is not high, and if the interfering signals are
exceptionally strong, wave traps in the antenna circuit are often used to reduce the interference.
A typical TV RF amplifier circuit is showed in figure 1. Notice that the input of the RF
amplifier is tuned. This results in better image rejection. However, many RF amplifiers have a
periodic untuned input from the antenna system. Okay, is that what they're saying? We'll see.
Also notice the bandpass RF coupler between the output of the RF amplifier and the mixer grid.
This tends to improve the selectivity and to give an essentially uniform response of
six megacycles. Bandpass RF coupler. Are they talking about that? To give broadband response
and to prevent oscillation, stagger tuning is often used. Two of the resonant circuits shown
in figure 1 are tuned to different frequencies. Two circuits alone give a deep valley between the
peaks of response, and the third circuit is therefore tuned to a mid-frequency and serves
to fill in the valley. The valley may also be filled in by loading the resonant circuits with
low shunt resistances such as R1 and R5. Oh yeah, so they're showing this is tuning,
and that is tunable. Where is R1? Oh, here it is. Figure 1 illustrates only one way that
these three tuned circuits may be arranged. Tuned circuit L2 to C2 is tightly coupled to the antenna
coil. Resistor R1, which may be as low as 2000 ohms, is shunted across the tuned circuit to broaden
its response. The bandpass coupler consisting of L3, C6, C5, C7, and L4 has a broad response
and is loaded through coupling condenser C4 by R4 and through coupling condenser C8 by R5.
The tube used in the pre-selector section is a pentode RF amplifier and may be of either the
variable Mu or the sharp cutoff type. The gain in this circuit is controlled by the AGC system,
although in some cases, a variable cathode bias resistor may be used to vary the bias of VT1 in
the tubes in the following stages. The RF tube must have certain characteristics that make it
suitable for amplification of very high frequencies. Its grid-to-plate capacity must be low if feedback
is to be kept at a minimum. For the same reason, the capacity between the plate and grid leads to
this tube must be as low as possible. In addition to this, the grid-to-cathode and plate-to-cathode
inter-electrode capacities and the capacities between the leads to these electrodes must be
low enough so that reasonably high gain can be obtained and so that the RF amplifier can be tuned
to the highest desired television channel when the inductance of L2, L3, and L4 are set at a minimum
Let's see if our section is anything like that. They are showing the section just before
it loads it to the mixer. Yeah, I don't know. This looks nothing like that. Or maybe it does
and I just don't understand. Oh, wait a minute. What's that there at the end?
I don't know that ours is much like that, but we'll keep reading. Mixer, first detector,
and oscillator. The process of frequency conversion involves the mixing of the locally
generated oscillator signal with the incoming modulated carrier signal. The process is basically
the same as in an ordinary broadcast superheterodyne receiver, except that in a television set there are
two RF carriers that beat with the local oscillator signal to produce two IF carrier frequencies.
In broadcast and FM receivers, a pentagrid converter is generally used as a combination
mixer-first detector-oscillator tube, but this tube is inadequate for the very high frequencies
employed in television and would result in noise and low output due to degeneration and
oscillator drift. In a TV set, there is a separate oscillator tube which may be in the same envelope
as the mixer. Let me see what they're calling. So we've got the first RF amp, and then we've got
the second RF amp, and then we've got the converter, and down here is the oscillator. I don't know how
they're getting two frequencies out of that. Maybe with those resistors? I don't know because
it loads into it. I don't know. We don't understand that part yet. Pentodes are commonly used in the
mixer circuit, but they require a high-level signal from the RF amplifier if noise is to be avoided.
If a low-level signal reaches the mixer input from an inefficient RF amplifier, or if the receiver
is located in a fringe area, it has been found that a triode mixer will give as much output as
a pentode and at a considerably lower noise level. Figure 2 shows the typical mixer first
detector oscillator circuit. Here a 6AK5 tube is used as the mixer. We are not using that. We are
using a 12AT7 converter oscillator. It looks like it's the same. This tube is biased by the drop
across R6 caused by the cathode current and by the drop across R5 caused by current flow through the
grid. Okay, so oscillator down here. You've got the anode basically feeding the mixer. So let's
see if ours is doing a similar thing. It's too far down. Oscillator down here. The anode,
the converter. Nope. Completely different setup. Basically the anode of the second RF amp is
feeding the converter. Okay, it's not really. I'm still looking. I mean, there is an RF
transformer there. I mean, that's similar to that. It's wired a little differently.
Okay, the IF transformer T4 is double-tuned and is over-coupled to provide the necessary bandwidth.
In this particular circuit, both the sound and video IF carriers pass through the IF transformer
and are fed to the input of the first video amplifier tube. Resistor R10,
which shunts the secondary transformer T4, loads the transformer to give a flat response.
See, all of that. I never, I will never get to the point where I know, oh, that's loading the
transformer so it gives a flat response. The oscillator is a 6C4 triode tube connected as an
modified cold pits using the grid-to-cathode and plate-to-cathode inter-electrode capacities
to maintain oscillation. Resistors R4 and R7 isolate the oscillator, permitting it to act
as an ultra-audion on any TV channel. Choke L3 is needed to isolate the oscillator's tuned
circuits further, providing a DC path for the plate circuit. The oscillator is tuned above the
carrier frequency by the amount of the IF frequency. See, I do understand it a little bit.
Trimmer C4 in the oscillator tank circuit is connected in series with C3 so that the
range of adjustment will be limited and the adjusting screw will be nearer RF ground
potential. Even so, a well-insulated alignment tool that is designed for higher frequencies is
necessary when C4 is to be adjusted. And the reason they're saying that is because if you put
a regular alignment tool in there, you're aligning it while it's turned on. And when you turn it,
when your tool gets near it, it'll freaking change all of that, just the tool being near it.
And so you got to use a special tool that allows you to actually adjust it,
because basically you'll adjust it and then remove your tool and it all changes.
The oscillator is biased by the feedback voltage on the grid. The tube then rectifies
the resulting grid current and the resistor-condenser combination
R3 through C5 is charged up to produce the operating bias. Other tubes are, of course,
used as oscillators, but in practically every instance, the ultra-odeon circuit is used and
the tube entry electrode capacities form a portion of the tuning circuit. You will find that not all
tubes will function satisfactory as oscillators, although they may be perfectly all right in some
other circuit. For this reason, servicemen always try several tubes in the oscillator stage when
trouble is suspected there and thus avoid many realignment problems. Ah, interesting.
So if you're changing out your oscillator tube and you put it in and it don't fix anything,
you might want to try another one. They're basically saying, yeah, some of them suck,
but you can use it somewhere else. Yeah, so this is just, you know, it's set up a little
different than the way we're doing ours. They're showing, and they're calling it the mixer,
where on ours they're calling it the, um, well, see, like, here's the detector in the
radio, the audio section. That's different. I can't quite tell what we're looking at here.
First RF amp, and they've got basically all kinds of little chokes and stuff built into it.
All of that feeds into the second RF amp, which, of course, amplifies it more. And all the chokes,
I guess, are to filter out all the weird frequencies and stuff. And then you've got
the same thing going on there. And then that eventually leads into the converter. So on our
little drawing, you've got the RF amplifier leading in through a cap into the converter
mixer. And then what comes out of the mixer does, in fact, let's see, it's kind of hard to see it
because it's right on the split of the page. What comes out of the cap does run into a
transformer. That's what we've got going on here. It's tuned. I guess they said that that one's
tuned. There's a cap across it, shunted across it. This one has two, actually. Yeah, the oscillator
is set up just a little bit different, but you know, very similar. There's the B+, running up
into the bottom of the IF transformer. And here is our B+, running up into the bottom
of the RF transformer, or they call that the IF transformer. Let's see what it says here.
T4, the IF transformer. So that's the IF transformer, which makes sense because we're
right at the IF. Yeah, so that is actually very similar. It's fairly similar. Yeah. So it's just
a slightly different mix of it, but it is very similar to that. So anyway, I don't completely
understand it, but you kind of get the idea. So basically the signal comes in, it gets amplified,
and it's going to be attached to a carrier frequency, an IF, whatever they call it,
what do they call it? An IF frequency. It's going to get attached to that. It's going to get
amplified. And then it's about to get split into two different, one's a video and one's the audio.
So, I mean, an oscillator is used. That's about all I caught of it, but we know that that's the
next segment. So if I cap that area quick enough, we can try hooking up a signal to it to end this
video. So let me set the thing back up. We're probably not going to have a ton of capacitors
to change here, are we? We got some resistors to check, and these are little mica ones we're going
to leave. Mica, mica, resistor, might have something going on here. We got some tubes to
check, more caps to check. No, the A's are going to be, that's not a cap, that's some kind of
inductor coil or something. Yeah, most of these are just resistors that we'll check the best we
can. A lot of these caps we're not going to be able to do anything with, unless I order a bunch
of micas. More resistors, but no caps. More resistors, resistors, resistors, resistors.
Yeah, so basically we're not going to have any caps, hardly at all. Might have a couple there
on the output. No, not even, yeah, not even them. Yeah, so basically we're not going to have any
caps to replace. I just got a ton of resistors that I need to change or check, and I'll bet
most of them are in spec because, I mean, why would they drift out of spec in the RF section
if they, I mean, they shouldn't have a ton of voltage running through most of that. Anyway,
let me set it up and see if I can find those resistors and check through them and find the
capacitors and at least get a look at them. Okay, folks, I looked through that whole section
and it's all, the way it's designed, it's right underneath these tubes here. The way it's
designed, you can't hardly get to anything. And like I said, all of the caps are either ceramic
or mica. There's no electrolytics at all. There are some resistors, but some of the resistors,
you can't even check because of the way that they're in circuit. You have to remove them
from circuit. I did, I was able to check some, but like if you look at these, like what's that,
4,300 ohm? It's a 4,300 ohm resistor, but it's in parallel across two little coils. So if you
check that, it just checks as zero because these are zero and on and on and on and on and on.
So what I've done is I have very carefully hooked up a signal generator. I think this will work.
I've used it a couple of times before. You may have seen that on some of my previous videos.
I've got it on RF out, which is 75 ohm with this cable, which I've got hooked into the antenna on
the back. And I've got a, you know, it's got a bunch of patterns that can display. I've got it
on the crosshatch. I'm not sure if I've got the raster right. And we're just going to turn it on
and see if we can get any kind of signal through it. All of the controls are all out of whack
because I sprayed them all and turned them and stuff. So we're going to have to adjust vertical
hold, horizontal hold, brightness, picture, all of that at least, you know, so possibly much,
much more, but I'm going to turn it on. Also, I have it plugged straight into the wall,
no more babying it. We got it because eventually it's got to live off of the wall voltage.
And we've recapped everything except the video section and the audio section.
So all of the power related stuff and the raster stuff should have caps that can handle it. This
one tube that glows really brightly, I haven't tested most of the tubes, but this one tube that
glows really brightly is the first IF amp. So when the signal comes in, that's exactly where it
goes. So we may not get anything on it, but it would be interesting to see if we get either the
audio or the video before we do the audio and the video in the next couple of videos. So here we go.
Okay. Sorry. I was texting somebody. All right, here we go. Something may blow up. I'm not sure
we're giving it the straight juice from the wall folks, or we're trying to. God, that one is a
superstar, isn't it? But I don't know if it's supposed to be like that. Maybe. And by the way,
I know, I know you're not supposed to touch the bare knobs, but on this one, it's not a problem.
Here, I'll make it better. We'll use this. Let's see if we get anything. There we go. Okay. I do
not know which one is brightness and it's all too bright. So that's not good actually.
Yeah. So let me see if I can figure out which controls are which, because I don't want to
run it that bright all the time. But maybe we've got a problem with the circuit that's forcing it
that bright. Okay. So it's not flickering like it is on the camera. The brightness control is these.
So I've got it all the way down. So we've got some kind of issue there for sure,
but it's hard to tell. It's probably so bright that we're not going to be able to see
an image. So let's change the channel though. Maybe we'll get something going on.
I just, I don't think we're going to be able to see an image through that.
And I don't even know, you know, what channel we're supposed to be on to get an image.
Plus you would have to fine tune it. Yeah. I don't see anything coming through. All right.
So we've got our high voltage, but we might have too much high voltage. Maybe that's the problem.
Or, you know, we've got some kind of thing with the signal still, which would be the video, right?
So our brightness, for instance, but you know, and I've got it all the way down. It won't go
any darker. Let's find our, let's find our schematic for that area. We messed with that
just a little bit. Here we go. So there is the brightness control. Notice I have not checked
off that capacitor. I wonder if that's our whole problem. We've got something going on there.
Where is that coming from though? Okay. It's the B plus. So it's the 235. It runs through a
resistor and the brightness control. So it's like a bias voltage that, you know, allows you to adjust
it. If that cap was screwed up or that resistor, let me think. Yeah. So we've got something going
on here probably. Well, I don't know. Because it could be anything. It could also be the heater
voltage is too high, which, you know, we've thought about because the way the series string
resistor, the series string tubes work and our line voltage, our wall voltage is higher. I guess
I could put it on the, I could put it on the Variac and just not run it at two, not run it.
Well, we just did that. Nevermind. That won't work. So when I had it on the Variac,
if you remember, I was running that at 235 and we had the same thing going on where the screen was
just really bright. So the reason I'm leaving it on is I'm just letting everything kind of
do its thing. It's not so bright that it's going to burn up the tube or anything. It's just
obviously you're not going to get any kind of image like that. And if I turn off the signal
generator, we get no kind of difference on there. And I have no clue what channel two is
or three or whatever it's on. Let me make sure that I can't change this to something else.
That's channel four. It's just, you know, it's so bright. And if you ever mess with a TV where
you turn the brightness all the way up, you can't see a signal whenever it's this bright, no matter
what you do, it could be displaying it perfectly on there. But if we can't get the background black,
of course, you're not going to see anything. I almost forgot one thing. There is a audio
generator on here. So our video is screwed up, but perhaps we can find the audio signal.
Got our speaker right here. Let's see if we can get the channel.
Aha! You hear it? It's not that loud. You can just barely hear it. I wonder if I can,
can that be fine tuned? Let me switch the, it's three kilohertz. Let me switch to one
kilohertz. I don't hear it. I hear it on three kilohertz though. You can just barely hear it.
Let's try on a different channel. Channel three, maybe it'll come in better.
Okay. So that is the correct channel. And look, the video is slightly different.
Hell, it might be trying to do it. Okay. Let me see if I can figure out where the
horizontal hold and stuff is. All right. I can't quite get it, but check this out.
We are getting a video. It's just crappy because it's so bright. See it? So that's the dot pattern.
That's the crosshatch pattern. So it is there. By the way, horizontal and vertical was this knob.
Just can't quite get it. So we've got a sync problem. Got all kinds of crap going on.
All right, folks. So that's where we're at. We will mess with it more next time,
but we are getting a video. It's just, you can barely freaking tell.
All right. So we're getting there.
