845. Testing a New Handle for MKM Hand Roller on a Teabowl/Chawan with Hsin-Chuen Lin 林新春 滾花紋茶碗示範

Hsinchuen Lin
205 followers
2 Video Views·Mar 22, 2025
To see or buy my finished work and pottery tools, please visit my Online shops:
https://sawfish-endive-kgks.squarespace.com/shop
http://www.etsy.com/shop/hsinchuen
http://www.etsy.com/shop/hsinceramics
http://www.etsy.com/shop/hsintools
To watch more of my YouTube videos, please visit my channel:
http://www.youtube.com/@hsinchuen
To learn more information, please visit my Website:
www.mypots.net
Instagram: @hsinchuenlin
Facebook page: Hsin-Chuen Lin Ceramics
Pinterest: @hsinchuen6518
[Music]
all right I just receive this handle for
the uh hand roller usually people use it
for hand roller but uh my design getting
in the handle so that you could hook it
on put it on the handle and then you can
roll it it's a lot easier than using
just your
hand it's rolling like this and I did a
test on the flat piece The Slap and now
I'm going to test it on the throne piece
using this hand rotor with the handle
this is my prototype right and this is
on the a smaller handle for from the mkm
and I also have a larger
sizeall my B System since I'm not going
to throw a big piece and then
adapter so that uh I I could throw a
smaller piece on this B insert so a
adapter and a smaller bed insert with
the flower shape so it's like this
flower shape servers a key so it's not
rotating
it um you can see that people using the
square one the circular one with a
little little Notch coming out but with
the flower shape design you don't need
to have that
so once you done you just lift it and
put it aside and put another one so that
is what this is all about and uh if you
have hard time to pick it
up it's fairly easy just get a piece of
stick and then you can open it up and
open it up and then put it underneath
and you can lift it so that's how this p
insert
work since I'm going to use this handle
to test it so I will throw a cylinder
and then I put a little bit of a support
going to put this the the Caro inside of
my cylinder and then I colored it in so
that the wall is fitting nicely on here
so that I when I'm rolling it I have a
support I can roll either horizontal way
or or rot it vertical
way okay
horizontal this way or
vertical and again this is the new wheel
from H that's stand it already um this
wheel is is quiet and uh enough power to
throw with
[Music]
make it smaller maybe the base should be
slightly
wider right and then I'm going to insert
the this carbo tube inside before I put
it in I wet the base so it's slightly
softer here so the base the corner will
be not so
rough and put it in the center and push
all the way to the bottom now I'm going
to eras up the wall and also make sure
the wall is fitting very tight on the
supporting tube
I start to push it from the base if I
push from the the top I might trap the
air so I want to release the air so
slowly color
okay so that's the the W that is fitting
and you can see that this part here is
slightly wider so you can use a
um a rib to smooth it out make it make
sure it's flat cuz I'm going to roll it
horizontal slightly remove the clay from
the
base okay this rib is my number two half
round rib the small
one right so I clean my hands
and then this is the roller so I'm going
to roll it here all the way around and
to prevent the clay from sticking on to
the wooden rotor I usually dip it in the
water sock it in the water so it's easy
to release without messed up the
texture and uh just hold it here to
support it on the top here and then I
spin the the wheel slowly and SL to push
the sideways so there's a pressure so
that the uh the texture will be deep
because I have the support the tube
inside to support but make sure you have
this enough
pressure and then you can do this
slowly okay I I to the Topo so that the
The Joint there will be a little bit of
overlapping if you don't want to little
bit overlapping you can find your
starting point and then once you come to
the start starting point and then you
release it um you can see that with the
water so it release the uh clay cleaner
the Serv is
cleaner um Yep this is very good uh up
without causing any trouble when I'm
pushing
it okay so that is good testing on this
handle and also this is made of a
standless steel so it's very easy to
clean clean up is also very
easy and then now I what I need to do is
pull this
up the supported to pull it
up I didn't show you that usually you
want to rra a newspaper so it will be
easy for you to remove the the tube
otherwise your tube will stick on here
on the inside harder to pull it up and
all you need to do is
just pick up and roll the uh newspaper
up
okay I have the newspaper inside so it
abser all the water and the slip so the
inside is fairly dry so I will try to
apply a little bit of water to licate
it and also the corner is slightly
messed up by the
newspaper so if you have a longer stick
like I do I have this is my number
six the uh compressing stick or the
stretching
stick and I think the uh the curve side
is very good for the B bottom corner so
I'm using that to compress
it so go from the center and
slowly move to the
side okay so I take care of the
corner and now I could the either use a
sponge or just use the hand to stretch
it or if you want to you can bring back
the number two number two half round rib
and then stretch
from the corner so the wall will be
smoother and depending on what you're
making if you are going to make a mug
then you don't need a stretch so
why can turn it into a mug
or if you are making it making a um a
tall then you can stretch it
wider let me uh turn it into a t ball
all right so that is the Keo and uh use
my number 17 the uh skirt trimmer the
white trimmer to go
underneath remove the accessive clay
from the
corner and putting a little style if you
planning not to
trim this little curve help for the uh
decoration so it looks more like a
finished
piece okay so that is the finished piece
and like I said that it's fairly easy to
remove it get this to there go under
underneath and then put it in there and
you can lift it up
easily and the base looks like
this I usually trim but if you're
planning not to trim you can put the
foot like
this a table with
texture so our topic for today is this
rot handle
get this handle and then you could
easily convert your hand roller into a
handle
roller right so this will be the future
product from my tool
set this one
and open this
up and
easy for clean
up this is my Al B
system Easy Clean um they don't work
they don't get mold they don't swell so
let's almost forever if you are using it
correctly and the other side you can use
that for trimming
and every time if you put it back it
will be in the center if you need it to
work on
it all right so that is my demonstration
thanks for watching and see you next
time for
[Music]
[Music]
