879. Throwing MKM BHR Roller Texture Tea Bowls with Hsin-Chuen Lin 林新春 滾花茶碗示範

Hsinchuen Lin
205 followers
274 Video Views·Jan 24, 2026
To see or buy my finished work and pottery tools, please visit my Online shops:
https://sawfish-endive-kgks.squarespace.com/shop
http://www.etsy.com/shop/hsinchuen
http://www.etsy.com/shop/hsinceramics
http://www.etsy.com/shop/hsintools
To watch more of my YouTube videos, please visit my channel:
http://www.youtube.com/@hsinchuen
To learn more information, please visit my Website:
www.mypots.net
Instagram: @hsinchuenlin
Facebook page: Hsin-Chuen Lin Ceramics
Pinterest: @hsinchuen6518
AI Generated·May contain errors
I'd like to show you my newly designed handle for the roller texture, especially the hand
roller.
Usually when you have a hand roller, you don't have a handle, so you could just use only
your hand or some kind of a ball to compress it.
But now I've designed three different sizes of the handles, two different kinds of wooden
or metal handles.
The setup is very easy.
All you need to do is get two screws and screw them both in.
I have three sizes, 100mm, 120mm, and 200mm.
These are the roller texture, the hand roller from either MTM or some kind of a generic
brand.
My handle is all compatible with the same exact size.
I'm going to use the 120mm to do my demonstration, making the T-balls.
This will be 120mm.
Here is the MTM rollers and some other brand.
I'm going to use this one to do my demonstration first.
Hook it up.
I already have the screw on, so the hook up is very easy.
Just use one side, point it to the center, and then you just pull and lift it, and then
just hook it on.
Because those are metal to metal, so it's not much of a friction and they can roll it
very freely.
I'm going to use my test system.
Sometimes when you want to throw something larger, you will have a lot of pulling force.
If you don't have your bag insert, you hold it on here without lifting it up accidentally.
One trick is that, put some water here, and when you have water, because this is fitting
very tight, so it creates a very good seal, so it's like a vacuum.
When you pull, it's very hard to pull it up when you're lifting it.
That's the design.
You see that?
I'm trying to pick it up.
It's very hard.
You need to have a tool to be able to do that.
You have a piece of a wooden stick and you can pull it up easily.
Once you have water underneath, it's very tight here, so it's very hard to pick it up.
Then, get my clay on top of that.
I center.
If you wanted to do it a couple of times to wedge the clay right on the wheel,
if you already wedged on the table, you don't have to do that.
That's centering.
Then, open it.
Pretty quick, I roll a cylinder.
For the texture to be rolled deep enough, when you roll it, if you just use the roller
to roll right here, it's very hard to roll it deep.
My invention is, you put in a support tube.
You put it behind your clay and support it.
Here is the tube.
You can use either a PVC pipe or any kind of cardboard tube.
Then, I'm able to pull it out easily because when you have clay attached to the tube in my stick,
I wrap a piece of paper around it.
When I'm done, I can just pull out the tube and then roll the paper off.
It's very easy to do.
Put it right here.
Before I do that, I could wet the bottom to soften this part here a little bit.
Then, put it on.
If you wanted to, you can cut it so that it will be almost the similar size, similar diameter of the tube.
You don't have a lot of wiggle room for when you try to cut it off.
Put it right there.
Adjust it.
Make sure it's in the center.
Now, I'm going to push the collar and push the clay up against it.
I have to collar from the base because if you start to collar, you're going to trap the air.
You don't want to trap the air in between.
So, you collar from the base.
It's fitting pretty good.
If you want to roll the texture vertical, this part here has to be very straight.
Now, I can see that the bottom portion is slightly wider than the middle section.
If you want to roll vertically, you're going to roll this way.
Then, probably in the middle, you won't be able to roll it.
I need to remove a little bit of clay.
You can use a trimmer.
You can use the trimmer to remove the clay a little bit here.
Remove it.
Make sure when you're doing so, your other hand should pull the clay away from you when you trim.
Otherwise, it's going to stick onto the surface.
You can probably leave the middle section a little bit wider too so that you will be able to roll it.
Leave the middle section a little bit fatter.
A little bit wider.
Then, scrub the clay from the base.
Let me clean up here.
Now, the surface is clean.
I can bring back my roller.
I'm going to roll vertical this way to prevent the clay from sticking onto the wooden roller.
Usually, you want to stick it in the water.
Soak a lot of water to help the clay to release.
You want to do it slowly.
Let's start from here at this point.
Push and then put a little bit of support behind it.
Do it slowly.
Attach and then release.
Do it slowly with a lot of water. That's the key.
Of course, with my handle to hook it on, you will be able to roll it vertically.
After that, all I need to do is pour this.
Make sure when you're rolling your newspaper, you want to leave about at least an inch without wrapping all the way.
So that your finger can be holding it here to pull it up.
That's how this works.
Also, if you are making something that is fairly tall, it's probably a lot of friction.
You might want to roll two layers of newspaper.
Now, all I need to do is roll and roll and twist and pour it out.
That's the newspaper.
Of course, when I wrap it, I apply a bit of glue to glue it on.
I need to apply a bit of water to lubricate the wall.
Also, the corners, if you don't want to make it 90 degrees sharp, you want to have a curve,
you can use a stick.
This is my stretching stick, number 6 stretching stick.
You can use that to smooth the bottom corner and make it round.
You can use a sponge or you can use your hand to stretch it to the shape.
Remember, now you cannot touch the outer part.
It's just the inside hand that's doing the job.
Then I use my number 17 wire trimmer to trim the base.
I'm rolling the texture from my FKM roller.
This is the BHR, Big Hand Roller.
They have a smaller one, shorter one, it's called HR, and a longer one.
This is the longer one.
They call it LHR.
Now, remove it, get a wooden stick and put it underneath and go in there and lift it.
That is the texture.
I'm making a T-ball so that you can roll the texture deep enough.
I use the same method and different textures,
two from MKM and one from other brands,
to roll the texture onto my T-ball's mouth.
This is the handle to hook it on, my design.
Very simple and easy, but very useful.
Again, I have three different sizes, 100, 120, and 200 millimeters.
Those are compatible with the mold's leading brand.
If you have the size that is slightly different,
you can always use a saw to cut it to be exactly the same length.
Then you just put the screw on,
and you can use my handle to hook it on and to roll it easily.
That is my demonstration.
Thanks for watching. I will see you in my next video.
