847. Making a Texture Teabowl/Chawan with a MKM BHR roller with Hsin-Chuen Lin 林新春 滾花紋茶碗 製作示範

Hsinchuen Lin
205 followers
4 Video Views·Apr 3, 2025
To see or buy my finished work and pottery tools, please visit my Online shops:
https://sawfish-endive-kgks.squarespace.com/shop
http://www.etsy.com/shop/hsinchuen
http://www.etsy.com/shop/hsinceramics
http://www.etsy.com/shop/hsintools
To watch more of my YouTube videos, please visit my channel:
http://www.youtube.com/@hsinchuen
To learn more information, please visit my Website:
www.mypots.net
Instagram: @hsinchuenlin
Facebook page: Hsin-Chuen Lin Ceramics
Pinterest: @hsinchuen6518
Right, so I'm going to try another roller to make a teapot. This was from MKM. It was a long one,
a big one, but I cut it shorter so it's fitting into my medium size roller handle.
Okay, so I try to throw a straight cylinder as closer to the size of the supporting cargo.
And then I just drop it into the center all the way down to the bottom.
And then I collar up the cylinder from the bottom, try to release the air.
So that's why I start to collar from the bottom and gradually go up to the top
until it's fitting tight on the supporting tube. And then I use a rip to
first clean up the base and then clean up the surface and make sure the surface is straight
and also without any slip in the way.
Right, and then bring the roller here and push against it all the way. Before I do that,
remember I always soak it in water. Then hold the supporting tube over the top
and then push against it. You can spin the wheel slowly.
Okay, so with the water it's easy to release without getting any clay in here to mess up the
texture. And pour out the supporting tube. Pour out the newspaper.
The newspaper inside already absorbed a lot of slip so the inside is a little bit dry.
After you pour it out, you might want to put some water in it. Before I do that,
I'm using my number six floor compressing and also the stretching stick. This part here is
curved and this part here is straight. So this is for the floor compressing but this part here is
for stretching. And also it's very good for the inside corner. So you will have a round
corner on the inside. Okay, the inside is taking care of and it's nice to cover the curve.
I'm going to put some water and use my number two stretching rip. It's a nice curve here.
This is my number two. And you can also use a round rip too. But this is a little bit thinner
so it's easier to reach inside. This is a little bit too wide. So since I'm making a tea bowl,
not a vase, I will open up the rim. For the tea bowl, this might be too tall so I will cut it
All right, so that's it for the tea bowl, the roller texture tea bowl.
Using this, the new handle that I designed. This is from MKM. It was a longer one but I cut it
short so it's fitting right here. And push against it to get the texture.
People ask me when to wire it up. Sometimes I wait a little bit, maybe a couple hours
to wire it up. But actually you can wire it right away. I just want to show you what my
wire looks like. It's fairly thin. The wire is thin so when you wire it, it doesn't affect
the rim. Sometimes if you wire it thicker, it might affect the rim a bit. But this is very thin
so it's very easy to go through without messing up the rim. See the rim is not moving, right?
Versus the thicker one, when you wire it up, but after you throw,
you'll rim might alter a little bit. But this is very thin so it's very less resistant and easy
to go through. And once it's ready to separate from the bag, you can wire it up again. That's
what I usually do. And then you can use a stick to just go underneath. There's a little notch here
so you can go underneath and then put it underneath. It's very easy for you to remove from
the bag system. This is my aluminum bag system. This is the translucent bag.
