Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
ladies and gentlemen this is joe's
classic video games back with another
arcade game pinball game repair video
for you this afternoon
this one's going to be a real doozy we
thought we'd better film this one
because it's pretty interesting
about a year ago we bought this dungeons
and dragons pinball machine at an
auction now if you don't know about the
deal with auctions
a lot of times not always but a lot of
times some of the machines that end up
at auction have
serious problems that the owner
either didn't want to spend the money on
to repair or
uh it's something that is nagging you
know where it pops up after it's been on
a while or something where the owner
couldn't figure out
how to repair it but anyway we got this
dungeons and dragons that's a little
beat up
um a little rough
and the problem with this machine was
that it caught on fire
now i don't i wasn't there so i don't
i don't know if it uh if it caught on
fire at the actual auction
or uh if it was before the auction or
whatever but
here is the cord they have cut the cord
off so that you can't possibly plug it
back in
now the reason for that and this thing
whenever we got it we've had about a
year i think
whenever we got it you could still smell
all of the burnt electrical
stuff in it so we're gonna have to take
this thing apart and see
what exactly happened now i looked at it
whenever we brought it in about a year
ago but i haven't paid much attention to
it yet because we just didn't have time
to go through it
i was looking for a new power board
because i know the power board is what
burnt up
and we were finally able to buy a brand
new power board for it
we found a gentleman that makes a
perfect reproduction so we have a
perfectly reproduced power board for it
licensed and everything
but now we need to see what all we have
to do i know a lot of the harnesses burn
up
so that's going to be a lot of work but
the first thing i want to do is when the
power comes in
i haven't worked on one of these this is
called a bali 6803 machine
which is the the type of processor that
runs this particular
model so i haven't worked on one of
these in a while so the power comes in
through the back and goes down to the
bottom of the cabinet so the first thing
i'm going to do
is look at where that line comes in so
we'll lift this up and see if there's
anything
inside the cabinet that looks messed up
or if it's all in the back box so
i'll lift that up and be back in just
okay so i slid the pit the play field
out of it a little bit um
and took a little look around inside
basically the power
line comes in behind that white cover
there
and then the way it works on these is it
runs through these wires down to the
switch and then back up to the top
so uh there's nothing in the bottom
that's all burnt up or anything like
that so basically we've got the power
right here running up to the top because
the transformer
is inside the back box so uh
we'll uh you can see right here
this is melted electrical goodies
so uh we're going to be looking at a
nightmare in the top folks so
if if you're squeamish don't look at
this next plan all right now i'm serious
you might want to hide your eyes
look at that crap
look at this
what in the hell people
holy moly so what you're looking at
is this is the cpu board
all of this damage to it is smoke damage
the best i can tell
we're going to take that apart and clean
it and try to make sure it's savable
but uh even the part here that's kind of
rough looking
these are all just diodes and resistors
that could be replaced if necessary
and these little transistors can be
replaced i think they're all good though
believe it or not i think that's just
soot from the smoke
and over here is the transformer
which is kind of a pain to swap if you
have to do that they're very expensive
and they're very heavy and very hard to
find
but i don't see anything melted over
there so i think it's probably fine
we're going to have to
measure all our voltages and and all of
that of course
that may be that may be the problem but
uh we'll find out
over here on the left is a fuse board
that works all the solenoids i believe
it looks fine and this up here is the
sound board it looks fine
but then and so here you have the
displays
who knows if they're all right or not
well if we can get some focus focus
the displays who knows if they work
and then behind the displays you have
the power board
which is most definitely not all right
so it's kind of hard to tell what
happened
um
we can probably tell more when we get it
open it looks like it happened right
around
here was the actual
problem so i'm going to look at my other
one and see what was even there
um but something was overfused or
usually a game won't do this if somebody
put the wrong fuses in it it might do it
okay so when you look at this
okay the power supports burn slap the
hell up we can get a brand new power
power board which is about 180 bucks
right
but much worse than that is all of those
wirings burn up
look at this crap
now i've i looked at this a year ago and
to be quite
honest this is not as bad as i remember
it
i think i looked at it before and went
what the hell and just covered it back
up
but now that i'm looking at it again i'm
actually kind of uh
enthused by this because it's not quite
as bad as now of course i got to replace
all this damn wiring
but i thought it was worse than this i
thought there were even more this isn't
as bad as i remember so
here's what i need to do i'm going to
take out the displays and get them out
of the way
so that we don't have to reach over
those the whole time
i'm going to take out the old power
board and uh
eventually throw it in the trash but i'm
gonna save it for now just because
that's
it burn up so bad i mean that's fairly
amazing that's why i'm filming it
i'm gonna save that just to show people
something to talk about
and then i'm going to have to go through
and clean everything
mount the new power supply board in
there and then
carefully separate each burnt wire and
then replace the wire with a new wire
and put it back in the connector that it
needs to go to
and just replace them now i'm thinking
10 20
30
oh 40
i'm thinking i've got about 50 wires i
need to replace
and this is one of those games that we
get these from time to time this is a
dungeons and dragons it's a cool game
but it's not a top of the line game a
lot of people
if they got this game and it was this
damn burnt up they would just part it
out they just sell the pieces out of it
so i think this is one of those
situations where we're going to save a
game
that most people would never save
so what i'll do with the wiring and i'll
film all this so you guys can watch it
if you just keep watching a video
um what i'm gonna do with the wiring is
i'm going to first separate
and figure out what each bundle does
like for instance this
this little bundle here i believe is
either the play field switches or the
cabinet switches it's one of these
connections
it's probably play field switches right
there
so that's not real important right now
what i'm more concerned about
are these power wires that all need to
be replaced
and then here you've got not only power
wires but power wires that are running
over here and actually running the uh
the mpu board so i'm going to separate
everything
cut all of these bundles apart see if
any of the wires are
solvable separate them and do the power
ones first with brand new wiring
and try to do it as nice as possible but
like i said it's about 50 wires so it's
going to take a long time
just figuring out where they go like if
you've got a wire here
that's part of this
you know it goes through here somewhere
and over here somewhere i mean how the
hell do you even track that down
so i'm gonna need to look at the
schematics and try to match colored
wires from this end over to this end
where they plug in and try to figure out
this wire needs to connect to this wire
and then run a new wire
with new connectors and things like that
so it's gonna be a lot of work but i'll
film it you can watch it while we do it
and um then hopefully when we're done we
will have a working
uh dungeons and dragons pinball so
that's that's our goal so the first
thing i want to do is start taking stuff
apart and cleaning it up a little bit be
back
shortly all right folks so we started
cleaning it up a little bit i took the
displays
out so that i could just get to
everything i took the
main board out um the back of it's
pretty smoke damage but we'll see if we
can clear that up
and i took the power board out which is
destroyed and
i cleaned up the back box and then all
of the soot wouldn't come off so we
sprayed over it a little bit to kind of
make it look a little more presentable
all that'll be covered with boards
anyways and again the displays are down
here so you won't even see any of it but
we didn't want it to look all black
where whoever
gets this will think that something's
messed up and uh
so we started trying to figure out
what's going on we've got
these wires here
that will need to be replaced and we've
got
these wires here that will need to be
replaced
and then i was able to take a big bunch
of them out
because there's one
harness here that completely will
disconnect so this part all of these are
fun
these are fun and these are fine but
here in the middle they all melted
together
where it went right over the board but
at least i was able to take this out
where i can work on it
separately so that'll make it a lot
easier
i can work one on the table instead of
in the machine
and so i've got uh wires here
and wires there so we're trying to
figure out what happened
this is the bad part the transformer
somebody has been messing with and i
don't know why yet
but they've separated it
see how this is coming apart it's like
they pulled on it or something
and a couple of the wires are separated
where they're not
covered anymore so i'm gonna have to
cover that up put that all back together
so it looks good
and then down here on the bottom see
these two wires that are
where they've taken them out of the
transformer
basically each of these wires goes in
and solders to a little lug
well two of the lugs they've removed the
wire from
and i believe the two wires
that go on that lug are these two
so they have removed those for whatever
reason
so somebody
the damn thing probably was fine and
somebody started messing with it and
trying to do something cutesy
and literally burnt the machine up so
we're gonna have to go through piece by
piece and get the schematics and uh
figure out how the power gets to the
transformer and then measure the wires
to make sure they're not shorted
together
and then very carefully check to make
sure everything's isolated and not
touching
if one of these wires touches the other
ones it'll blow something up so we're
going to have to make sure that that's
all
back how it should be and then test it
and it could be that the the transformer
is bad and we had to swap the whole
thing
so they're very expensive and hard to
find so it's probably
like 150 bucks if that happens so we
will try to save what we got
but we'll see i'll uh once we get a
little further i'll film another video
all right folks we are farther along and
we have been doing some detective work
the first thing we did was we went down
and we kept cleaning things up
and we went down to the bottom and we
replaced the cord if you remember
earlier in the video
i showed you it had been cut so we were
able to put a nice long
beautiful cord on it and plug it into
the wall now before we
plugged it into the wall of course we
checked everything out but we got out
the schematics and basically the way it
works is that the power comes in from
the wall
it goes down to the switch underneath
the game and then comes out of the
switch and it comes up here
on these blue and yellow wires here now
these were just like that in the cabinet
i didn't
take them loose or anything they were
laying in the cabinet like that so
somebody has really been screwing around
with this thing
so before we plugged it in of course we
looked through the schematics now i've
got a manual here a copy of the manual
for it
and so basically you know whenever you
get something
catastrophic like this people always
think oh man i wouldn't even know where
to begin
some of you might have already said that
well you begin at the beginning
so here's where the power comes in from
the wall
and it goes to this barrister which is
like a varistor how do you i don't know
how you pronounce that but
that's a thing that it it basically uh
it has to do with something with surges
it can blow it's inside the cabinet
right where the power thing comes in
it's fine if it blows it'll be all burnt
up or it'll be shorted together and it's
not shorted together or anything so that
was fine
the filter the line filter is what the
plug the power plug plugs into
it wasn't it didn't test shorted on the
input on the inputs or the outputs and
so then it goes over here
to this is this represents the switch
underneath the cabinet
and uh of course all that was fun it
also after it goes through the switch
it goes to the it says optional
back door interlock safety switch
i don't there's no back door on a
pinball machine so this is just some
kind of generic thing they just copied
in but
this would actually be your one-off
switch but and the service outlet is
inside of it
all of that looked fine nothing looked
messed up and then you got your yellow
and blue wires that run up and they go
into this connector
that plugs into the power transformer so
that's how far we are right now
since the two wires were disconnected
from the power transformer
we went ahead and turned it on and
tested the voltage on those two wires
and we've got our 120 volts and when you
turn it off uh
you've got zero volts so the switch is
working all of this is working fine now
basically the cord was cut off that was
the whole problem with that
so if you look at these the yellow wire
plugs into pin one of this 11 pin
connector
12 pin connector actually just 11 of
them are used though
and then the blue wire is supposed to
plug into pin five
and then you see on the other side once
it goes in five it jumpers around and
connects to six and seven
which jumpers around and connects to ten
and seven uh six
jumpers around it connects to three the
reason that they have it like this is
because if you put a different plug on
it it would do different voltages
for different countries so you can see
we're going to end up connected to the
115 volt
you could also connect it to 120 100 120
or 115
actually now that i read over that that
wouldn't be for different countries that
would be so that you could raise the
voltage if you have low wall voltage and
things like that but we're not going to
mess with any of that but here's the
interesting thing
the first thing it does is it goes
through this into this red wire
and it goes into a fuse three amp 250
volt
slow blow so you've got 120 volts coming
through the wall
you know wall power and it runs into one
of the wires
it's fused you want it to be fused okay
so these two wires
someone has pulled out of
this connector and you see the jumper
wires and stuff it should go in two of
those
spots and then one of them connects into
this red
fuse holder so we popped this apart and
the fuse wasn't blown
now imagine that the whole damn fan
caught on fire but it didn't blow the
fuse
so why is that it should be a three amp
250 volt and this is what was in it
now i'm gonna lay it down here and try
to get as close as i can it may not
focus
see how it's dark on the edges and it's
it's lighter in the middle
that's because it tried to burn up
it tried to blow the fuse which would
have cut all the power to the game
it would have cut off all the power
right here and nothing would have had
power
but whoever worked on this put in a
15 amp fuse where there's supposed to be
a 3 amp fuse
now and it's a 32 volt so this is a car
fuse
so they didn't even a 15 amp fuse
that's so much amperage
most most of your uh sockets on the wall
are 20 amp
some of them are 15 amp so before that
fuse blew it probably would have blown
the breaker
in the house or wherever they had it
plugged up so it just
so what happened was they had a really
heavy fuse in there which they shouldn't
have
and uh it's something shorted something
messed up
probably a diode on that power board you
saw where we were showing the diode
we'll look at that again here here a
little bit in a minute uh whenever i get
that far we want to compare the new
board with the old board
and figure out what happened but
basically something one of those diodes
went bad or shorted or something and it
could have been anything it could have
been like a light bulb
locked on on the play field the diode
went bad shorted together
started causing all kinds of current to
run through it but it didn't get 15 amps
running through it which is how much it
would have to get through it
to uh blow the uh blow the fuse
and so once it got up to eight or nine
amps or whatever it just shorted out
and literally caught the board on fire
so i hope that's a
lesson to people do not take
the fuse values for granted if it says
three amps
don't put a four don't put a five and
whatever you do
don't put a 15 that's crazy
and don't cut fuses out sometimes
they'll take a fuse out and put a nail
in its place or something just
crazy crazy literally you could burn
your house down
whoever i mean whoever did this they're
lucky that they caught it because they
could do it
the the machine could be running and
then you go you walk in the other room
and one of the diodes goes bad and
you've got a 15 amp fuse and now this
one catches on fire while you're in the
other room
it never blows the switch the uh the
fuse so
so that's certainly probably one of the
major problems but uh
we're going to have to start uh on the
wires and everything now that we saw how
the
transformer i showed you how it was
coming loose so what i've done is i've
i isolated the uh the two that
the two white ones there i isolated them
to where they can't touch each other
and then i glued the hell out of it so
that it
uh so that they can't touch together
put a little zip tie on it so that the
wires weren't separated where they can
all
do their thing and so what i'm going to
do next is i'm going to figure out where
the yellow and the blue wire go in here
once i do that it's going to power up
and put a fuse the right fuse in
once i do that it's going to power up
the transformer and the transformer
sends all its power out
on this block now remember we've got
these two
here that are disconnected
that are the
where did i put it they are the black
and red and
black and blue wires so for whatever
reason they disconnected those so
back to our schematics the black and red
and the black and blue
are the 48 volt
which is the phase c and phase d for
play field and back box bright lights
so basically the the game can can turn
lights on and off
the whole sets of lights on and off and
they had an interesting way of doing it
with the ac power to use
uh two phases so that basically they
could put a heck of a lot more light
bulbs in the game
than most pinball machines up until that
point that was
one of bali's cost cutting measures so
we're gonna
what we're gonna do is we're gonna get
the the
transformer wired up and then turn it on
and watch it just to make sure it
doesn't explode
and doesn't catch anything on fire and
then once we're sure that it's not
going to catch on fire or whatever we'll
go through and we'll measure every one
of those voltages
just to see if it's putting out the
correct voltages i think what's probably
going to happen is one of them is
probably missing and it may
actually be those
those lights so i'm hoping that whoever
was measuring it and messing with it
just didn't know what they were doing i
already see evidence of that
so i'm hoping that it still works they
just didn't know what they were doing
and couldn't
couldn't figure out where the power was
messing up because i do not want to
replace that transformer it's going to
be very expensive and even hard to find
so
i'll be back in a minute after we test
the voltages we'll see what's going on
all right folks now as you can see we've
got a light bulb on in the cabinet now i
put the
this uh little throwaway bulb back in
there just to
make sure that we had voltage in there
after i checked everything and we do
so you saw where we did our little thing
i put the two wires back in where they
go
replace the fuse with the proper one
made sure nothing was shorted got
everything
good and then i tested everything
nothing was plugged in
as you can see there's the this plugs
into the power board to burn up
but it's not plugged in right now
and i checked every voltage and all the
voltages were fine i couldn't believe it
so these people took apart
the transformer because they were having
some kind of problem with the
with the light phases what just crazy
so we put it all back together and i
soldered those two uh wires back to
where the the two lugs that they go to
and put a lot of electrical tape on all
that so that nothing can get messed up
and then use some zip ties so that
nothing can get pulled if the
wire goes a weird way or something and
all the voltages test out including the
120 volt so once i figured out it did i
went ahead and plugged it back up
which means that the light's working now
that's a good thing to have anyway so
that you can tell
when you're working on the game whether
or not the power is turned off whenever
you got a game where nothing's plugged
in
and you're messing with things you don't
know if the power's on or off but now
that we've got that light bulb turned on
we can
be sure when the power is dead to the
machine as we work through all of these
wires
so the next thing i want to do is start
working on the wires
that plug that are inside the cabinet
that plug into the power board
so be back whenever we start some of
that i'm going to go ahead and end the
video here
this part of it and i'll do another
video as we start replacing all the
wiring
and upload it it'll probably be up next
week or so so
subscribe to us here on youtube if you
like this type of videos and we will see
you next time let us know what you think
in the comments below