Check Out Our Patreon Account, for Unreleased Repair FAILS, Concise Repair Tips Not Possible In This Long Form Video, And 1 on 1 Repair Assistance with YOUR Project!
Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
Ladies and gentlemen, this is Joe's
Classic Video Games back with another
cool pinball repair video for you this
evening. We have been working through
this Ballet Playboy video. I mean a
Playboy pinball machine here and made a
couple videos on it. Uh we did one where
uh we just looked it over, put it
together. The thing actually still runs.
Um and then we did another one where we
tore apart the playfield. We're working
on some plastics and things like that. I
got it all cleaned up, but uh we need to
do some painting and things and we've
been working through the boards a little
bit. Um the thing was already booting
up, but one of the things that was wrong
on the P on the previous one was we
didn't have any of the controlled lamps.
They're all working now. Well, not all
working, but the controlled lamps
themselves are working now. There's a
bunch of them that don't light up, but
we'll get to that. Um but, uh I like to
kind of work through the boards in
order. So, the next thing that we're
going to mess with is the solenoid
driver board. And then we'll get over to
the lamp driver board where we're uh we
can figure out why a bunch of these
aren't doing anything. And they just all
turned off again. Interesting. What a
great thing to catch on video. You saw
that, right? They were working and now
they're not.
Uhhuh. We're in test mode. That's why
there's nothing on the display. So, the
game is actually running right now.
Let's see if we just wiggle the
connectors. If we just wiggle it. Now,
you don't think that I'm going to get
shocked, do you?
Okay, that doesn't do it.
Interesting, huh? So, it died right here
while we were looking at it. Well, let
me set up the camera and we'll check the
voltage again on the uh on the power
supply and see if the power supply
itself
uh died on us. Well, I'm glad it did
that because we didn't catch on the
previous video exactly what fixed our
problem.
So, let's check the voltage on test
point one.
It is gone. All right. Perfect.
Okay, folks. So, all I did was replace
the fuse. Turned it off. Replace the
fuse. And now we've got a whole bunch
more of the lamps working. So, we still
got some kind of problem with that. But,
we're going to move on and do some
connectors and things. And I'm gonna
just turn it on and off and just see if
it happens again. And uh see if I can
figure out what's going on whenever the
voltage disappears again. Um
interesting. Okay, so uh next thing
we're going to mess with is this
solenoid driver board. I'm going to do
the regular updates that we do to it and
uh pop it out of there. But we
definitely have something going on with
the lamps. And I think they're all kind
of they're not attracting now. They're
just kind of stuck on and stuff. So
there definitely something going on. We
need to get over to the lamp driver
board, but we're working our way that
way. Okay, so here's the solenoid driver
board that was present in this Playboy.
It's an early one, it looks like.
November of 77. It actually says
revision one here, but uh I guess that's
that revision of that number. I don't I
don't think it's the first revision of
this number
because I've seen the ones
Well, h you see how the traces look.
It's actually pretty
old. But those are there's some that are
handdrawn traces. I can't remember if
those are only on the sterns though. Um
it's an early one though. Okay. So, uh
I'm going to do what I usually do. So,
I'm going to clean all the connections
and we're going to resolder the
connections.
Um, of course, remember the thing's
already running, so we're just trying to
do preventative maintenance. I'll clean
up the back. Everything looks great. I'm
going to tie test point one
and test.3 together. So, test five, this
one up here on the top. That's where the
12 volts unregulated, comes into the
board. And then this regulator
turns it into 5 volts. And then the 5
volts goes out on test point one.
Right. So over here, test point one is
connected to that. Well, one of the
weird things it does is it loops the 5
volts from about right here out of the
connector and then back into the
connector right here. And that go that's
test three. It's the same exact voltage.
So why would they do that?
I've been looking into it a little bit
by studying how the schematics work and
stuff. It actually kind of makes sense.
Well, no, it doesn't make sense. Never
mind. Take back what I just said about
it making sense because it still makes
no damn sense. I forgot about something.
So, um
it's just it's a weird setup. Someone
said that they did it for test figures.
There's some test figures that uh um
some test jigs that do it differently,
but I don't know.
Anyway, this board is three separate
things. So, this is the high voltage
area for the displays. So, this makes
the high voltage 190 volts for the
displays. That's what this area does.
And then there's the 5VT regulator. It
takes the 12 volts and turns it into 5
volts, a regulated 5 volts, right? And
then there's the bottom of the board,
which is the solenoid driver board. So,
it
grounds all of the solenoids through
these big
transistors.
Got to watch what I say. If I say the
wrong word, people want to tell me I'm
saying the wrong word.
Communication is getting harder, folks.
It's getting harder.
Um, people act like they don't know what
you mean if you use the wrong word.
I don't know when when we got to a point
of time where people publicly dis
proclaim how ignorant they are, but they
do. It's weird. They'll say, "You said
it's a transistor,
but really it's an SCR. I'm confused."
It's just this weird thing. It's like,
yeah, you are confused. You're confused.
Anyway, rant mode off for now. Um, so
there's this whole thing where this
makes this gets 12 volts on this
connector and then it creates 5 volts
that goes out this connector and then
goes from there to here. So, the whole
point is there could just be a jumper
going from here to here. Why did they
put it on the connector? because you
can't plug in the voltage to this. You
can't plug in the input to this and then
have the output disconnected. That would
make sense because you could you could
say, okay, uh 12 volts is coming in. We
don't have the output connected out. So,
none of these chips are getting this
voltage until we check it. Because this
thing might short and send 12 volts out,
right? So if if these chips on the same
board had a jumper going straight to
them, when this was screwed up, it would
fry these chips. So you might put a
little disconnect where it's
disconnected, but it's not like that cuz
it's on the same connector that the
input's connected on. I've been
complaining about this for years. I have
yet to to my satisfaction figure out why
they did that. But it makes sense if
they had like a test jig. Maybe it works
different. So on the test jig, maybe it
does that. But um maybe it has the wire
comes out and there's a there's a um a
switch on the jig, right? So it might
maybe they got a big thing like this.
I've seen those before, but I just never
paid much attention to them. And you
plug the board in and it sends the 12
volts in and then it measures that five
out. Maybe there's even a meter. Let's
just dream. Maybe there's even a meter
that says 5 volts going out. But you
look at it, it says that it's 9 volts
cuz this is screwed up. and you go,
"Wow, good thing I didn't have the
switch on, which sends the power to
these chips, too, through that little
wire jumper."
It could be something like that. I don't
know. Just just trying to imagine here.
So, um, but since we don't have that and
since they are connecting those two
together with a wire that goes off this
connector, we're just going to do it on
the board. Makes it a little more
reliable. Um, might help you keep you
from having problem with the solenoids.
Uh, so we're going to do that. We're
going to replace this 5V filter
capacitor. These get old. About time for
them to go. Um, we're going to do a
little ground upgrade, too. Just just
two little ones.
Okay. So, one is
this ground for the the rectifi or the
the regulator um only connects on one
little pin. They've got all of the
grounds
connected
separately. So, it comes over here onto
one pin.
But what you can do, you know what? On
this one, I can't do it.
Well, we won't be doing that. I mean, I
could do it by running some longer
jumpers, but usually there's a ground
trace that runs right under here, and
it's real easy to just put a jumper, but
on this one, it's not there.
So, maybe we won't do that. Maybe we'll
leave it alone.
Um,
but what that does is instead of the
ground leaving the board on just one
pin, that could have problems, have a
little resistance on it or whatever, and
that screws up your 5 volts for the
entire game. If you tie that ground to
some of the other grounds that are also
leaving the board, um, now it has
multiple paths and it kind of ties
everything together. It's just a neat
little upgrade that people do. And then
the other one is you can do the same
thing up here for the displays. This is
the filter capacitor for the displays.
It's a big one connected there. And this
is the ground. And so you can connect
that to here.
And that does the same thing. Um,
to be honest with you though, if you
look at how this thing is laid out,
all that's going to do is connect it to
the ground plane of the back box.
because that ground plane that runs all
the way around the edge doesn't actually
connect
to the ground u any of the grounds
created by the voltage regulator um or
that are you the voltage regulator or
that are used in the high voltage
um or that are used in the solenoid
drivers.
That's probably the ground there because
it's running to all of the transistors
so that it can um they can be grounded
to turn the solenoids on.
Anyway, enough of that. I guess it says
on the front too what the ground is.
There it is. Yeah. So, this trace this
ground trace usually is on the back. You
could do the same thing here. Run that
from there to there.
Ah, maybe we'll figure something out.
Um, but again, everything works. So,
we're just trying to do preventative
maintenance stuff to maybe hopefully
make it a little stronger in the future
for Mr. Keith for the Playboy. Keith
wrestler. Cool dude. All right. So,
resoldered them like I said, put a new
filter cap on.
Put a jumper from the ground to the
other ground. And by the way, it is
connected to this trace. They're
connected through the VAS to the front.
And it's all around the front. And on
the front, it's connected right there or
I mean right there. You got to be
careful. If you go by the test points
though, it'll help you figure it out. So
the the one trace has the ground test
point on it. It's clearly the ground on
the front. This is marked this one's
marked positive. This one's marked
ground. So it's clearly the ground. Um
so you know, you got to be if you if you
connect the wrong couple things on this
board, you'll fry all kinds of stuff.
You really got to be careful. And then
this is test point one to test point
three. Um, up here I just was able to do
it with a glob of solder.
Um,
I wanted to show you something though.
You got to look out for stuff like this.
Um, I see this a lot actually. So, this
is a cap
that has another cap soldered on top of
it. That's actually a factory thing I
believe. I see that a lot. A lot of
these have that setup. Remember this is
revision one of this number and it's the
the November 77 revision of of this
number. They made several of these cuz
they were rocking and rolling. They were
selling literally tens of thousands of
pinball machines at the time. Every one
of them was just banging out a ton of
them. They had already made uh eightball
which sold 20,000
machines. Matahari probably sold eight
or 9,000 machines. This Playboy that
we're working on probably sold 12 or 15
thousand Mach. I mean, there's a ton of
them being made. So, they're constantly
revising these things and stuff. So,
they would do things like just add
little like they wanted that cap and
that cap there. So, they soldered it on
top because they didn't have the board
made yet where there was room for it.
But the problem is,
you know, something like a capacitor, it
has two connections. One on this end and
one on this end. And this one up here is
the positive connection. And this is the
negative connection. Well, this uh
capacitor here uh doesn't it's not
polarized. So, it doesn't matter which
way you put it. It doesn't have a
negative side and a positive side. Or
does it? Am I lying to you? That says
positive. So, maybe this does. That's it
shouldn't. But whatever. Um it doesn't
even matter. The whole pro the problem
is the way that this capacitor is
constructed. If you look, the leg
is tied to the outside foil of this cap.
And then if you look on this side, the
positive
is tied to the
pin coming out of the center of the cap.
But the way they have this installed,
that leg is touching not only the
positive, but also the negative because
it's leaning over and touching the the
metal can itself. Look at that.
How the hell that hasn't shorted out
over the years, I have no clue.
But come on, people. You can't do that.
Come on now.
You're touching both with the You see
what I'm saying? So, it's the positive
is touching the negative. This is
jumpered over basically by that one
little leg there. Can't do that. Now, on
this end, technically,
it's not that big of a deal if you're
touching that and the the the
canister.
But that's not a good idea either
because you got you you know you got to
make sure that you know that they're
both the same electronic connection. Now
it could be that there's like a film
wrapped around that can. I don't think
there is though. I think we're looking
at an aluminum
can. So I got to clean that up so that
it doesn't actually
do that. So one of the things you could
do since it's already kind of a hack,
you just put it on the back of the board
and then it it doesn't you don't have to
worry about it touching that. So, I
might just do that.
All right. So, we got it installed back
in. I put that cap on the back. Um,
we need to check the voltage to the high
voltage to the displays. We need to
check the 5 volt and see if it's close.
And we've still got it doing the weird
thing with the
with the uh the lamps. They're kind of
working. They flicker. They do weird
stuff. Now, they're back to coming on.
And they're not all flickering. There's
definitely some problems going on with
that still. We may end up having to take
this back out and replace the bridge
rectifier, but we have moved on to the
MPU,
which doesn't look like it has a ton of
damage to it, which we're going to get
lucky on that. So, I'm going to pull it
out, put it on the bench, and we'll see
if we can do a nice little service to
it.
So, what would a nice little service to
it be? Well, there's about one, two,
three, four. There's about four things
we need to do to it. One, we need to do
the same thing we did on the other.
Resolder
these four connectors.
And the reason for that is because they
get broken solder joints. So, let's see
if I can see any on here for you.
It's always at the end whenever you pull
the connector off, it uh it breaks the
solder. Yeah.
I don't know.
See that second one? See how there's a
ring around it? It's completely broken
loose. But wait, we now have a
microscope.
All right, so we got this Tomlav
microscope
and uh you don't necessarily need a
microscope, but it just helps you see
things and I can make the point better
on my videos for sure. This thing works
great, by the way.
So
this ring around it that that the pin on
the top is physically disconnected from
the solder pad. It's not even connected
to the board right now.
This one the back part might be, you
know, and then you also run into a thing
where amperage is a thing. So like if
it's just barely connected, you're not
going to get much juice through there
in my layman's terms.
Okay. Same thing there. You see the
stress fra f fractures. It's a physical
break. It's physically been broken.
And it's the ones at the end because of
just the nature of how you physically
pull the the connector off. So, uh, we
got to resolder all that. Now, whenever
I resolder those, and we'll do that here
later because we got to clean it up. But
whenever I resolder those, what I do is
I take a wire brush, not a crazy one,
but a wire brush, and I clean the solder
off.
just I I scrape it up just because you
get nice clean bright solder. You're
getting some of the dirt and the dust
and the oxidation off. Yeah, you can try
to clean it off. Um if you had some kind
of liquid that you could paint on it to
clean it off or uh you can do it with
isopropyl alcohol, but it you end up
where there's stuff down in between and
everything. A wire brush just works
good.
get it nice and fresh and then it'll
take new solder and make it easier to to
to clean up. So, that's the first thing
we got to do. We got to we have to re
solder all of that.
Let me turn off my camera.
This thing's just cool. You can
just slide it out of the way when you're
done with it.
Easy peasy. I like it.
So, that's one. Um, next thing we need
to do is
the bad connections that we're saying we
have here, we also have on all the
sockets. So, where the pins go into the
socket,
um, there's issues.
Look at that. That's black. It's It's so
oxidized and tarnished that it's black.
So, what you'll find is
if they sit in the socket just right,
the part that's touching the pin in the
socket, the little the little thing that
squeezes the leg, it's clean. And the
the pin of the chip is clean right where
it's touching it because it they're
touching each other. So, they haven't
tarnished. But what happens is these
move a little bit over time. So, just
anything will do it. flexing it, rolling
it down the street, looking at it wrong,
and that pin moves just slightly, and
now you have a tarnished part of the pin
that's been exposed to the elements, and
now it's touching the metal thing, and
it's not conducting electricity through
it. So, if you get one pin doing that,
thing won't work. So, we're having this
problem with the with the uh the lamps.
Well, this board controls all of that.
That's why I was saying we're kind of
doing it over to that area. The power
supply creates the p the the the
transformer transforms all the power and
rectifies it to the voltages that you
need. It's sent up to the solenoid
driver board which again changes it from
12 to five. All of these chips run off
five. The power comes in here. Um the
corrosion that we're going to see here
in a minute harms this connection. But
then you also have all of these ROMs
that tell the whole thing what to do. It
it literally tells it which lamps to
turn on and turn off. And it uses these
two chips to do it. So, one of these
chips is going to do lamps, one of
them's going to do switches, uh, one of
them's going to do displays, uh, etc.,
etc. These PIA, these two PIA chips, um,
on the Williams games around this time,
they had,
I think, three PIA chips.
Uh, this one, it doesn't quite need that
many because of the way the solenoids
are done. But
so my whole point is bad connections on
these legs in the socket will cause
problems too. So we're going to
carefully remove each chip, clean the
legs, and then put them back in. The way
I do it is I've got a like an old worn
out file, and I just clean them up with
the file a little bit. Don't go crazy. I
mean, you don't want something super
aggressive that's going to cut up the
legs of the chip or anything. You're
just trying to get all the tarnish off.
Other people do it other ways. You can
do it however you want. That's how I do
it. And I've been doing it like that for
I don't know 20 years. Everything's been
going good. More than 20 years. So
that's that. Um so that's the second
thing we need to do. We need to clean up
all the sockets. Uh the third thing we
need to do is we need to remove the
battery and clean up the damage that the
battery has made. So this battery they
mount at the bottom of the board to do
the bookkeeping and stuff. And as it
leaks over the years,
it starts corroding the board.
and it can handle it a little bit. Right
now, the board's still working, but you
see how it's creeping under that chip,
for instance. See the legs of the chip?
That's corrosion.
So, that's corrosion
that has creeped up these traces,
through the pins, and then up onto the
leg of the chips.
Right? And the chip's still working. So,
it's right on a borderline though, that
pretty soon that's going to stop making
contact. and this board won't boot
anymore. So, we got to clean all this
up. So, we're going to remove the
battery, clean this stuff up. It's a
it's a base, it's a um it's not an acid.
It's not battery acid. It's battery
alkaline. So, um you actually use an
acid to neutralize it. So, you clean it
all up. Try to get rid of all of it on a
mild case like this. And this is mild.
Out of a one to 10. 10. The worst I've
seen. This is a a one
or maybe maybe a two maybe, but not
really.
Um like look look over here.
Nothing.
And this is not battery corrosion. This
is just where the the pins are
tarnished.
So, you know, you got a little bit, but
again, it's still booting, so it can't
be too bad.
Um, and then they get over here a lot,
too. But on this one,
nothing. Everything's cool. So, it's not
bad at all. So, that's the third thing
we need to do. We need to clean up all
that. This is going to need a new
socket. Um, and then the fourth thing we
need to do is we need to put a new
battery in it that won't leak. So,
that's what we're going to do. So,
um, I guess a better order would be to
do the battery first. So, let me cut it
off and start cleaning stuff up. You can
actually see why the battery didn't
destroy the b the board yet. It says
TDI,
the helpful people,
2320 Wisconsin Avenue, Downer's Grove,
Illinois, 60515, and their phone number.
Now, Illinois, uh, Chicago is where all
these pinballs were made.
the the battery that's on the these
boards originally looks just like this,
but this particular one has a date code
on it that says September of 86
or that might be the ninth week of 86.
So, this game was released in 78.
Um, so eight years later, somebody
actually swapped a battery. So, because
of that, the batter is not quite as old
as they usually are, and it's survived
it.
All right. So, I cleaned it up. I'm
going to put some vinegar on it and
leave it on overnight.
Um, it cleaned up pretty good, actually.
These traces here, it's it's usually
these three. Actually, um, are what will
give you problems. So, if you work on
one of these and it won't boot,
check these three traces because they're
right there in the corrosion zone. And
if that if that via that vaia gets
corroded going through the board,
they're no longer connected. So you need
to connect you need to look where they
go. They they all end up over here and
connect to this 5101
from down through here.
Um and I think one or two of them
actually connects to the 6810 as well.
And so they they go through the board
and then along the back and then to here
and here. And so what'll happen is
they'll break right there. Like that'll
be so corroded that it's no longer
making contact with the villa that goes
through the board. Usually the back's
not that bad, but so I put a new socket
on it. Put the 50 clean the 5101 and put
it back. Cleaned all the chips. I've
gotten up to the CPU, the 6800,
and it's getting clean, but
one of the legs broke.
So, what happens is after they just get
so tarnished, the legs get fatigued. So,
it's still on there, and you could
probably solder it back on, but it's
about to break.
And there it went.
So, and it it's it's it's not it's not
um every pin like, so if I mess with
this one, they're all all the other ones
are nice and solid,
but that one was weak and so it just
broke.
And that's the way the
CPU crumbles.
Okay. The rest of them cleaned up pretty
good though. Um I'm going to put another
6800 in it. Oh, let me show you the
back. Those traces I'm talking about.
So those traces are like this one and
these two.
Right. So it cleaned up pretty good.
Like I said, it wasn't that bad.
All right. New 6800.
And I'm going to show you what I do for
the battery. All right. So, the way I've
been doing the battery lately is putting
a button battery in it. About like that.
Or maybe it's the other way. I think
it's the other way. About like that. Um,
you can put NV RAM in though. You just
take this chip out 6810 and replace it
with a uh RAM chip that is that doesn't
need a battery to back it up. But if you
want to lose this battery and put one of
these in, it's actually really easy. So,
I use that as one of the mounts
for the negative.
And then the other one I just measure
out and drill a hole through the board.
You got to just be careful that you
don't hit these traces so it ends up
being right here or somewhere. Um, and
then you can you can mount the battery
holder there and then jumper over to the
positive trace with a diode so that it
doesn't try to charge the button battery
whenever you're turning the board on.
So, I'll show you how that all comes
out.
All right. So, there's the battery
holder in the ground is soldered to the
ground plane. The positive is going
through the drill hole
and connecting to a battery, I mean a
diode over to the trace the battery is
connected to. So, basically power can go
that way, but power can't go that way.
So, um, whenever you
have the board turned on, there's five
volts right here
just because of the way the board's
powered.
I may have that wrong. They may have it.
There may be a diode over here or
something, but anyway, there's five
points, five volts on this side of it,
and there's only three volts on this
side of it. So, it's not going to do
anything. And because of the diode, it
can't charge it or try to charge it
because it would it wouldn't charge it.
It' just make a big mess. Um, and then
whenever the board's turned off, the 5
volts is gone, but the 3 volts trickles
out of here because now over here, the
voltage is zero. So the 3 volts trickles
out, goes through the diode and powers
the 5101 RAM chip just long enough on
this pin.
Just long enough, just enough with just
a little trickle voltage. Just enough to
keep the memory.
Wait, have I got that right? It's the
Yeah, that's the 5101. Okay. So, I was
wrong when I said you whenever you do
the NV RAM, you don't replace the 6810.
You replace the 5101. The 6810 is the
work RAM, you know, which is what makes
the game work. But the 5101 is what
saves the the U info. So, you have to
get a little daughter board or a little
NV RAM that fits the 5101. They make
them specifically for um these ballet
boards, but I like putting in a little
battery holder and a diode. Okay, I want
to show you something on this ballet
supersonic that we did that we did all
of that all those videos on. Okay, so
that that big score there, the 295,000
or whatever. Okay, that is the high
score of the game since we put the
battery in it. You can go in and reset
that and everything, but I want to draw
your attention to what it does after
that. See how it says 03 and then the
other one say 000000.
That's because I put a free play ROM in
here and the the guy that did the free
play ROM, he purposefully made it say
three
in that display whenever uh the game
turns on. So before a game is played on
the very first game, it says 03.
So, the reason I mentioned that is
because if you watched on the previous
two videos of this, whenever this thing
booted up, the battery is long dead. Uh,
the score that it would say is 808.
Now, that can't be an accident. It said
blank blank 808.
There's no way that's an accident. It
must be coded into the software somehow.
So, let's see if the thing will still
boot with its new battery and uh its new
6800 CPU. Or it's not a new one, but
it's new to it. 6800 cuz I broke the leg
off the one. All of the pins are clean
on the PAS. And we'll see if that does
anything for our lamps, too, by the way.
Two, three, four, five, six, seven.
Yeah, I just have the soundboard out
because it's in the way of removing this
power supply. So, I removed it so I can
work on that because we've got those
we've been having those problems with
the lamps.
So, let's look at the score.
So, they all say zero now
and they say uh
660.
Did it just Did it do something weird a
second ago where it just went to blank?
Okay, whatever. All right, so the now
the playfield lamps.
I think we might have fixed our problem.
Look, they're all lighting up in a way
that makes sense now.
They're not doing that weird flicker
thing.
So why would that be? It's because these
PIA chips
uh are what ultimately sends the signals
to the the lamp board to make the lamps
work. So, if you have a bad connection
on those in the socket, it could do
that. So, I think that might have
fixed that problem. Okay. So, next up,
I'm going to pop up the playfield and um
replace the light bulbs so that we can
because we're going to mess with the
lamp board next. And uh we want to make
sure that we get all of the bulbs
working and see if there's a rhyme or
reason to the ones that aren't working.
See if there's anything wrong apparently
with the lamp board. This one is
flickering. Look,
it was doing something weird. I saw it.
Maybe it's just a flaky bulb. Yeah. See
there? Okay. So, um yeah. So, let me get
let me uh pop the playfield up. I'll put
it in lamp test. We haven't done the
general illumination lamps yet either
because we got to do some paint work and
stuff. But, uh I'll put it in lamp test
and we'll see if I can get all of them
to work. Um,
I like replacing all of the bulbs
whenever I do it, just so I know they've
got nice, fresh,
real light bulbs in it. None of them,
none of that lead crap.
Okay, so I replaced the lamps, uh, the
general illumination lamps in the back
box. And I replaced all of the, um, the
computer controlled lamps in the back
box. They're all working. Every one of
them's working. the playfield. We
haven't done the GI yet because we get
still got to clean the uh we got to
paint the playfield and wax it and all
that kind of stuff.
But I did all of the
uh computer controlled ones
and
almost all of them came right back to
life.
The ones that don't work are the 2000,
the 3000,
the 5X,
and Miss September.
So, I only got four bulbs that don't
work.
And no matter what I do, they will not
work. So, it's got to be a board problem
or a wire or something.
So, I'm going to pull out the lamp board
and we'll figure it out. All right. So,
here's the lamp driver board. So,
there's four that don't work.
Um,
one of them is J1 connector J1 pin one.
So, that's suspect because whenever it's
the end pin,
it's really easy for that pin to get a
bad solder joint.
Looks like the problem to me
for show. So that's that one.
Um
the 3K is Q36.
I don't know what kind of item that is.
I thought they were transistors, but I
was informed that was incorrect.
I shouldn't say the stuff like that.
So, I just won't call them anything
anymore.
And um it's shorted. Now, you might say,
"Well, if it's shorted, how come you
don't have the light on?" Well, if it
depends on how it's shorted. If it
shorts base to
how would it be? If it shorts base to
collector,
see it's shorted
ground to anode,
right? So if it's shorted one way, the
light will never come on. If it's
shorted the other way, that light will
always stay on. So this little thing
here, this is shorted.
So, I'll see if I can find another one
of those. Um,
okay. And then Q26 is J17
and Q1
the miss September is J124. Well, none
of those are at the end of the
connector. So, it's probably not a
solder thing. And they test fine. So, I
don't know. I'll probably just swap them
anyway. I I'm not that good at testing
these things, whatever they're called.
And these things, whatever they're
called. They're definitely not
transistors, though.
Do not call them transistors. Um,
so yeah. So, I've got two. The one I
know is bad. The other one I think it's
the solder joint, and the other two that
I can't tell, I'm just going to swap.
And we'll see if that gets us our four
lights back.
Okay. So, that seems to have done the
trick. Every one of the lamps that can
flash is flashing.
Some of y'all will insist that some
aren't. The lamps are the most
aggravating part of working on these
because people always go, "Oh, this one.
Oh, this one needs re Oh god, this one
needs rep. Oh, I don't think the green
one's Oh,
it's just Oh, good lord. Okay, so we got
all that. I think the thing next to do
is mess with the soundboard because
then, you know, we're basically done
with all of the PCBs and I've already
got it out of the machine anyway.
Someone So, it plays this really
interesting little tune
um that I was thinking we showed in the
previous in a previous video. I was
thinking was the Playboy tune, you know,
like they had a tune, I guess, back in
the day. And I'm Yeah, I was born in 78,
so this is all before my time.
I was but a gleam in my daddy's eye
whenever this stuff was popular. But
anyway, with that said,
so I don't know the theme song, but I
did play it on the computer and it
sounded like it's trying to play the
theme song. And then somebody replied
and said that they remember it from
playing it back in the day and it didn't
sound right. So, I don't know, maybe
maybe the soundboard's messed up. So,
uh, um, we'll take a look at it and then
we'll try it back on the machine and see
if it sounds like it's it's missing any
of the notes or something. There's not
really a good way to tell, I don't
think.
Um,
it just plays some little
some little notes. I don't know how you
could tell if uh if if they're correct
or not. I did I did uh look up the ROM
and it has the correct ROM on it. So,
it's the right board for this machine.
So, if it's playing the wrong tune, I
don't I don't know.
So, this is it. And the way it's
controlled is with the solenoid lines.
So, I guess if the one of the PAs had a
bad connection on one of the solenoid uh
lines, which would be these here, or if
um there was a bad connection on this
board, you might lose one of the control
lines. And so therefore it would make
the the the sounds that the triggers be
wrong.
Um
I don't know. It does look like that end
one is is off.
Is that a control line? Yeah, it is.
Look, goes right to there, jumps across
and goes straight to that chip.
Mhm.
Yep. seen it a million times. All right,
so I'm going to clean it up, resolder
those, and I'm going to replace
the smaller caps.
The big one usually you don't have to
replace, but sometimes the smaller ones
introduce a lot of noise and stuff, so
we'll go ahead and swap them. It's very
It's very easy. Very, very easy. It's no
big deal. Oh, and here's the ROM chip,
so you can fact check me. I know how
y'all like to fact check me.
It's a E729-18.
Confirm. That's for a Playboy.
We better double check that. I'm going
to go fact check myself. E72918
is the sound ROM for Kiss, Lost World,
Playboy, $6 Million Man, Super Sonic,
and Star Trek.
So they use the same one. So basically
what whenever they change that ROM, what
they're changing is the key, like the
octave, not the key, the octave that the
notes are in. Uh you can hear it on a
few of them. It just it's a different
it's a completely different octave. Um
so yeah, so it's the right one. And
72951 is the one for Paragon,
Harlem Globe Trotters, and Dolly Parton.
[Music]
That sounds right to me, folks.
[Music]
This is like the test in the
[Music]
All right. It's definitely a play on it.
[Music]
So, we'll let it go on until it gets to
the little melody a little bit. You can
hear the melody of the pinball machine
in the background.
[Music]
now. Come on, people. They're trying. It
is about as good as they could do with a
pinball machine at the time. That's how
it's supposed to sound. It's almost dead
on it. All right, folks. Well, that's it
for the boards. Next time, we'll get
back onto the playfield, get it finished
up, and uh then we need to troubleshoot.
We need to check switches and solenoise
and play it. We can't play it right now,
though. The all the stuff's off the
playfield, and it's uh it needs some
work to protect it. We don't want it to
wear or anything. So, we're going to
repaint some of this stuff, touch it up
a little bit, clear coat it so it
doesn't wear, and then wax it, and then
we can put it all back together. We
ordered a couple uh plastics that were
broken. Um so, we've got those, and uh
we'll be able to put it all back
together. Look pretty good with original
type stuff. So, we will see you on that
next video. I hope you enjoyed it. We'll
see you next time. Now, if you like
watching us work on these valley pinball
machines, here's another really cool one
that we did a while back. We'll see you
on the next one.