Continuing Work On Our Hearts Spades Allied Leisure Industries Cocktail Pinball Machine.
Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
ladies and gentlemen this is Joe's
classic video games back with another
cool pinball machine repair video for
you this evening we have been working on
this Allied Leisure heart Spades pinball
machine uh for quite a while and uh
we've been trudging through it a little
bit at a time here and there if you
watched the previous videos uh we did
one where we worked on the power supply
we did another one where we worked on
the um flippers that needed to be
replaced because they were the um there
were parts missing uh we 3D printed some
flippers and uh we did one where we
cleaned up the Playfield worked on a
solenoid that wasn't working and a few
things like that so we are on to our
next little bit here I think today we're
going to go ahead and change all the
light bulbs and see if we can get it
into the test mode to test all of them
one thing I've noticed about the bulbs
is that the game overlight was blinking
whenever we first started messing with
it but it's not doing that anymore so we
need to see what's up with that and uh
just replace all of the light bulbs
there is a after we do that I'll see if
I can get it in the bulb test which
apparently blinks them all so that would
be cool um and then we may have some
upgrades we do to the game board we're
at least going to check some of that out
uh there's some cosmetic stuff left to
do and then maybe we can play it a
little bit so let me um I'm just going
to put up the Playfield Swap all of the
old light bulbs and the new ones there's
really not that many on this one 10 14
18 19 20 21 22 23 24 25 27 28 29 30
31 32 33
34 I see you know not a
ton so I'll swap them out and then we'll
see where we're at after that okay folks
I did Swap all of the light bulbs if you
uh look really closely the ones that
aren't on are lit up just slightly
that's because they've got a
resistor designed into
the game board on each lamp or at least
on most of them so that it's kind of
preheated I guess so that they can turn
it on and off quicker so if you look
they're all kind of just barely lit
up and that's just how they're
designed so because of that you can kind
of see which ones are going to be your
your problem child so I had one that
wasn't doing that I turned it a little
bit and then we got the little bit of
glow from it but there are a few that
aren't so like this
one is not lit up at
all this
one this
one this
one um there's just a few that don't
have anything going on but you know some
of them are out like that one but you
can see the little bit of glow where
it's preheated
basically um this one here is a unique
one that it looks like the way it gets
power is whenever the coil comes on for
the uh the gate
and uh I oiled the gate a little better
so I think it's going to be all right
hopefully uh so that's that there's also
a light down here that's the coin door
light that shines above the coin door I
suppose and it's not on either so I
don't know for sure we're going to make
a list of
them you got one here as well sometimes
if you just turn
the uh Bol
it will make a better
connection and your problem is that you
have a socket issue so like that's
obviously a socket issue if I mess with
the bul it
works all right so I'm going to make a
list of the ones that are not working
and then we'll see if we can figure out
if it's the uh the game board well we're
going to put it in test and get them to
all light up and then make a list of the
ones that aren't working and then also
like I mentioned we've got the game over
light that's not blinking anymore but it
could just be that the bulbs burn out
some of the stuff is Led
stuff and some of them are actual lamps
still um so I'm going to see how we put
it in test
next okay to start the test you just
press the button in the coin door and it
will uh start the credit and score
display should sequence from z9 0o
through nine and repeat the first led on
the right side of each score will always
remain a
zero so after you do that remove the
ball from the out hole we don't have it
in there press the credit button for 5
seconds the credit display will show two
test mode two score display number one
will show the number of any switch that
is
stuck test mode three press the T Test
switch for approximately two seconds
just to make it confusing credit display
will show
three tap very lightly the surface of
the Playfield if there are any switches
not correctly adjusted Gap too close to
number that switch will be displayed in
score display number
one make the necessary adjustments then
press the credit to credit press tuck
credit button to remove the number from
the score display okay test mode number
four press the test switch for
approximately two seconds credit display
should show four now remember this was
the first company that did uh solid
state um pinball so this is kind of
archaic it might be better than Williams
original one though I don't know
uh press test switch for approximately
two seconds credit display should show
four ignore any numbers on the score
display ignore them Joey ignore the
numbers on the credit
display he said he would the following
lights should be lit one extra ball win
lit two collect Spades value 1,000 2,000
3,000 4,000 collect Hearts value 1,000
and special win lit ignore the game
overlap now you see what they're doing
they're making us go through like
certain lights at at one time it's weird
I'm sure there's some sense to it it
must be like those are the ones that are
controlled by this 65 20 or whatever all
right test mode number five press the
credit button for approximately one
second credit display shows five the
following lamp should be lit collect
Hearts value 1,000 2,000 3,000 4,000 now
if you look the collect Hearts value
1,000 was also lit up on the previous
one 10,000 bonus lamp double bonus lamp
triple bonus lamp
okay test mode number six press the
credit button for approximately 1 second
credit display shows six the following
should be lit ball in play 1 two 3 four
and five same player shoots
again test mode number seven press the
credit switch for approximately 1 second
the credit display shows seven in this
mode the player LEDs are lit and the
score displays are extinguished okay
test mode number eight press the credit
switch for approximately 1 second the
credit display shows eight in this mode
the bonus lamp countdown from 9,000 to
1,000 after which the game over lamp
flashes followed by the tilt lamp you
got that keeping that
straight test mode number nine is the
coils okay so yeah so the the lamp test
mode is a little janky in my opinion but
we'll see what we can figure out so
let's do the switch one first well I
think I could just reach in
uh yeah so it's right
there
six all right so all of those are just
fine next up we hold it for 5 seconds
but I can't see the play field so we'll
just see how that
goes see if that
worked not long enough I
suppose it's going to make me put the
Playfield down but I don't want the
Playfield down because I want to be able
to mess with the light
bulbs all right I'm gonna put the play
field down
aha it wasn't working because I misread
it to go into test mode you momentarily
press the test switch but to go to test
mode number two you press the credit
button that's the button on the front
that's the start button that's
completely
different all right let's try it again
all right
okay you just hold it and let go of it
all right so
uh we're going to have to I guess look
at that paperwork to just make sure
we've got all of the lights correct so
it's Ace through four on Spades the King
of Spades and the ace on
Hearts okay so this is test two this is
actually supposed to be the stuck switch
test so it's supposed to tell us here if
there is a stuck switch
now the four on the first thing I think
it's because of a bad connection to this
we haven't messed with it yet it's been
doing that off and on since we started
messing with it so
um we're supposed to hit test to go on
to switch to so it's going back and
forth between having us hit test or
credit so it looks like we hit test to
go on to test
three okay it jumped to four maybe I was
supposed to hit credit so on four four
those are the lights that it's supposed
to show on
four
um so let me see how to go to
five right credit button to go to
five and it said that it should do those
four 10 and then double and triple okay
yep so it's
working perfect so far all right how to
go to six so six is the credit button
again and it should be uh ball and play
1 through five and same player shoots
again which is
there ball and play one through five but
the same player shoots again when isn't
working so let me I may be able to just
reach it from the
front nope let me see if I can mess with
that a little bit oh was one of my
favorite problems it was brand new
Chinese bulb didn't work so put in
another brand new Chinese bulb because
that's the only place you can get them
now and it
works okay so let's see how we go to
number
seven okay so it says press the credit
switch it's been saying credit button
but it says press the credit
switch I'm going think it's a typo that
it's the button still the credit switch
could be the coin switch and uh the
display should go out and then the one
and two players should come on and it
should go to
seven yeah okay so that's correct that
who
knows um all right how to go to
eight went out on its own I think
there's a bad connection on that board
we'll mess with that um so if I hit that
again it should go to eight and it
should start counting down the bonus and
then when it gets to the end it should
do game over and then it should do
tilt okay so game over isn't
working that was working earlier like on
the previous videos too I haven't
replaced those bulbs yet so I think what
I'm going to do is go ahead and take
this off so that we can get a look at
that uh PCB down there while we have it
in this test mode it'll be easy to see
if it fixes it and I think that is
working fine it's not starting at 10:
it's supposed to start at 9: actually it
did 10
earlier okay so that's what it looks
like with the apron off you can see the
little
scoreboards very
cool and look they this one has five
LEDs on it as well even though they only
use two of
them and then there's the credit
board the new light did not fix it so
we've got a bad connection on the board
or I screwed something up um we'll talk
about that here shortly this is flaking
if you just kind of move it
around so it's probably a bad connection
on whatever pin connects to it or
whatever um I would guess that's a
problem on the connector not on the like
a solder line on the board let's see if
I wiggle the connector if it'll do it
too
yeah so resoldering that will probably
fix that you could probably just unplug
it and plug it back in but it's kind of
hard to get to
um okay so I think I think that's all of
the bulbs actually there's a few over
here like that one was with the gate we
were talking about um the opens gate
closes
gate um and the other ones just stay on
all the time so it's the there's it
doesn't have the ability to turn on a
ton of
Lights um so yeah I'm cool with that
okay so I'm going to turn it off and I'm
going to take the board back out the
main board and figure that out this will
be easy to test because it the way it
was working was it was just blinking the
entire time that uh we had it on before
all right so ironically enough now this
is uh this is one of those weird moments
when I make the the video do all kinds
of weird stuff and it
goes in the previous video only like one
person caught this that said anything
about it when I've tested this this uh
if you look these three lines are the
transistors right so this one was bad
okay that is the one that was
controlling the right pop
bumper now when I turned the board over
and we were talking about
it I said this one's bad but really it
was this one was bad right so I pointed
at the wrong one and I said so I got to
replace this one and one person caught
that and they said no no it's not that
one it's that one right but after I
filmed it I caught that it was that one
I replaced the right one okay then I put
it back in well guess what that is the
one that does that light the game over
light so the energy there was something
telling me that there was going to be a
problem with this one I don't know isn't
that strange so like it was the last one
on the row and so I just thought
whenever I turned it back over oh it's
the last one on the row and I pointed to
this one instead if you watch the video
right but this one was the one that was
bad so I replaced it and it fixed the
pop bumper but now this one isn't
working right it tests fine though so I
don't know I'm I'm thinking it might
just be a bad connection on The Wire
I'll keep messing with it if if um I'll
spray some cleaner in the uh plug and
I'll I'll look at the wire on the other
end if it's not just a bad connection
thing I'll try swapping this just to
make sure but we'll figure it out so
anyway whenever we first start a working
on it the game over light was working
right okay so I think the next thing I
want to do
is
uh the gentleman John Robertson at uh
flippers.com has worked on a bunch of
these he has a bunch of suggestions to
upgrade the boards however he basically
says that you shouldn't even use this
board the one with the connector up here
because it's the first generation of the
board and it doesn't have uh protection
built into it uh for if power comes down
some of the switch lines and things like
that so I'm going to look on his website
and see if there's anything we should do
to this board while we have it out just
to um update it to what he thinks is
appropriate and um see if he's got
pictures of of this hack that's on here
I don't know what they were actually
trying to
do but for whatever reason they have
done quite a hack on it that may be
something to do with adding the
protection in I'm not sure but we'll see
what he says on flippers.com as
suggested for these and if I feel like
that it's
necessary okay so I'm on flippers.com
that's a great site by the way for of
this obscure stuff he's obviously been a
fan for a long time has figured out a
bunch of stuff with him so one of the
things that He suggests is replacing the
uh fuse holders if they're not the one
piece plastic type that they're weak and
they will break so we'll check those in
ours uh and remember there's a bunch of
fuse holders on the actual power supply
I'm kind of looking through these
backwards because of he's posted new
stuff as he identified new things that
he wanted to let us know about um and He
suggests upgrading the power plug
we see the little blue jumper there
there's a red one above it and a brown
one above that
basically one of these is like a power
Rail and a ground rail so they've got on
some of them they've got just one wire
going in so he's saying if you jump or
it over you'll get a much better
connection so I think we'll probably do
that if I've got those pins I think I do
um and then he gets into uh so he talks
about the 5volt power supply we worked
on that in the first video if you didn't
see that go back and
check and then uh so here's an update
that he did in 2017 he says as near as I
can tell
Ali which is Allied Leisure Industries
released four versions of their
motherboard uh 6504 based CPU so the one
we've got is PCB okay so he's saying
they're all called PCB 50210
one25 then he says the PCB 5021
125e is the first
version uh that's with and the second
version that's without the upper right
card Edge connector um actually upper
left card Edge connector unless he's
saying uh it might Mount different in
certain games but he's talking about
that one so this is the very first
version of the board but there was also
a second version of the board that is
the e
that just doesn't have that connector or
that's the easiest way to tell what it
is okay and then it
says without upper right Edge card
connector but no switch input protection
so both versions of this board have no
switch input protection and this is
another thing you can tell is that this
board is smaller than the other ones so
he's going to talk about the other two
nexts they're actually a little bit
taller uh and later PCB 502
10125 which is the same number but
revision H the first version of that
board had resistors the second version
of that board had 22 dodes to replace a
bunch of resistors that are on the board
then he says I highly recommend
replacing the resistors for dodes banded
in facing the Ed the card Edge connector
he's talking about on the third and
fourth versions of the board the H
version it took me a little while to
figure out what he's talking about um
and then he says use 1 n42 or higher
rated diodes so basically this version
of the board doesn't have input
protection on the switches so we'll get
into that in a minute it says
um oi manufactured a number of pinball
games all based on one mpu board as
shown below mpu system 2 and three the
mpu was powered by a single plus five
power supply usually located on the
bottom of the cabinet uh you want to
make sure it does produce 5 volts plus
or minus 25 volts plus or minus a quar
volt at the mpu you can measure the 5
volts at the filter capacitor mounted on
the lower left side of the m mpu board
the way it's mounted in RS it's the
lower right
side um the pinball games made using
this
mpu the features lights switches and
coils were rearranged by aler Chang the
rules for each game include disco 79
which was a cocktail AOS one which was a
cocktail hearts and Spades which is this
cocktail ho down which was an upright
Roy Clark the Entertainer which was a
cocktail star shooter which was a
cocktail take five which is a cocktail
Thunderbolt which was an upright and
getaway which was an upright so that's 1
2 3 4 five six seven eight there were
nine different machines six cocktails
and three
uprights uh and they service the mpus
and everything right so let me show you
a
picture of
the the other version and then we can
compare
all right so this is the taller version
this is the H revision that he's talking
about this part of the board is very
similar to the one I've got but they've
added this bottom part and the reason
that they added it was so that they
could add these diodes and capacitors
that they're using for input protection
on the
switches so on our board these
connectors are right up
here pretty smart way to do it and then
another thing they did was they removed
the extra transistors that they didn't
need now I was thinking that that plug
that goes up here would be necessary for
the back box maybe on the
um on the uprights but I don't know
maybe not you don't really need
transistors in a back box so maybe they
had them I don't know flash bulbs had
even been invented yet at that point but
um so they have removed the connector
that's on ours and they've removed these
and these and these these now if you
look on
ours that is there it's just not
populated you can see the update and
they have removed that top left
connector but everything else is in the
same place even all this which I guess
is like the reset section and the clock
section around the
CPU is the same I'm sure there's minor
differences
okay now we've got all these resistors
I'll show you that here in a minute
those would have been right there on the
original
design all right so back to what he's
saying um this is an update from October
25th
2024 he says we realize that a number of
boards have died because of voltage
surges to the coin tilt test and start
switches and this must stop
Parts blown include either a 6530 or
6520 68 21s and a number of TTL
chips look at the photo just below and
you will see that we have added six of
the 1 in 401
diodes after cutting the underlying
trace this isolates the TTL and 6530
logic from the switches and will greatly
reduce the risk of damage to even the
earliest boards which will still need
the DI the diode isolation board when
finished so he is working on a isolation
board that you just plug in underneath
your board between the connector and it
and it just you know you're essentially
modifying the harness to make it where
um the diodes are in line so what he has
done is he has cut the trace and put
five diodes there and one diode there in
I think what's going
on um is that the early
board no that's a that's the later
version
yeah so this is the H
revision I guess whenever they did their
diode upgrade they left some of the
switches off so they didn't put the
diode protection on
the test the coin switches the start
button and uh something else so service
switch I guess which is the start button
whatever um so he's suggesting that
adding those because basically the
factory didn't do it whenever they did
the board revision
um so we go back to this one it's some
of these connections
here actually boards turned around so
it's some of these connections here I
guess some of them they didn't add the
diodes in looks like there's resistors
there
um so and he's saying that you can do it
even on the earliest boards which
looking at the board yeah you could
there's room where you could cut the
trace and just uh solder a diode in okay
and then it says uh
um the plan now is to make an isolation
board that fits fits between the mpu and
the three bottom plugs to provide switch
input protection for these boards almost
ready all right
so it says the single mpu board I'm
calling system 22A now the reason he's
calling it that is because uh he
mentions in another part that there was
a system one in some of them that had
like 10 little boards all over the
bottom of the cabinet that ran
everything was all separate I'd love to
see that I've never seen one of
I've seen I had one of these before I
had to take that or take five take
that's a a boy band I had to take five
uh cocktail a while back I think it's
called take
five um I had one of those and it had
the same board and then I've got a
couple parts boards in the back that I
showed in an earlier video so I've seen
those but I've never seen the one with
all the little separate boards that'd be
cool to see so he's calling that system
one he's calling this system two and
again this this guy pretty much has
worked on more of them than most people
so he really kind of is the the Pioneer
in Reinventing this
stuff uh he's saying it uses a single
logic board that originally had keep
alive resistors for the
lamps so that's
these uh PCB 502
1025e and then he says
FG uh note this board is not recommended
for use due to the lack of input
protection circuitry for custom 6530 is
more on upgrading this board later the
photo shows system
2B so he's saying that the one I've got
is system 2A is what he's calling it the
photo shows system 2B mpus with the
resistors not installed by the factory
so the the 2B basically they changed the
design and they just basically didn't
put those resistors in that are on my
board uh note not all revision e had
these keep alive resistors installed
system 2A a can be identified by the
card Edge connector on the upper left in
the first photo the card Edge connection
was removed for the later system 2 b c
and d and a number of extra IC were
added to help protect the 6530s with
system 2C and 2D if you have a system 2B
or 2C mpu I recommend adding the 22
input protection
diodes as described below for all switch
lines to help protect the 6530s from
electrical
shock LEDs if you are replacing the
incandescent lights with LEDs to your
system 2A or B board you have to remove
the 36 keep alive resistors on the
bottom of the mpu board these resistors
will otherwise cause your LEDs to all
light up keep alive resistors are there
to help keep the filaments of the
original incandescent bulbs lamps
slightly warm so the thermal shock of
being turned on would be less stressful
for the light bulb these resistors were
dropped in later mpu boards they are
numbered R51 r67 blah blah blah system
2ab PCB uh e note the resistors over the
middle 22 pin connector the unused
connector on the upper left and the
jumper wires on the
rear I've not seen Board number F or
G so there's just e and H yeah so he
can't find
FG uh the plan now is to make an
isolation board that fits between the
muu and the three bottom plugs to
provide switch iner protection for these
boards almost ready so here's the
problem that I've got though with what
he's saying now I'm not disagreeing with
him I just can't figure out
something so he has written on this
Parts only no input protection
right um I'm looking at my
board and it has the same chips
populated that his
does yeah so there's a couple missing
and things but it's pretty much the same
but on mine the resistors are all in
here right okay so I've got the
schematics here
and I'm looking at the schematics so
he's saying to install diodes on all of
the switch lines now this is for a
[Music]
later or is it
[Music]
actually I'm looking here I'm
looking basically if you go through the
schematics I don't see how the
board I don't see how the 60 530s are
directly
connected to the switches I see that the
6520s are but I don't see how the 6530s
are so let me go to the other page of
the schematics here and I'll show
you now I'm not saying you shouldn't do
what he
says I'll explain it here in a second so
here's a 6530 all of these
lines none of them go to the card Edge
connector they all terminate at other C
chips so if so let's say that like the
coin switch somehow got some kind of
shock to it like somebody literally
shocked the coin door or something
people used to do that by the way if you
didn't know people used to go around and
shock the damn coin door because it
would send a a shock down the the board
and they were hoping to get a little bit
of electric jiggle on the board and it
would give them a free credit or
something people do that all the time um
it was common to take like a Zippo
lighter and try to do it and all kinds
of stuff and static electricity and
everything else um but so they terminate
with these 6520s which are 65 which are
6821 peripheral interface adapter chips
okay and if you look here are the diodes
that have been added on the newer
version so these are the switch lines
here coming in and they run through a
diode and then they have a cap tying It
To The Ground I
guess but pull down U not yeah yeah pull
down capacitor or maybe yeah and then it
runs up into the Pia okay so if you were
to shock that or get voltage down there
yeah it may fry the Pia which is a
6821 okay so that's that
one
the
6530
here the lines
here all connect to ic2 ic13 and they're
used to control like solenoids stuff
right so on on my board those are
actually
populated
so 6520 6520 6520
6520 6520 those are all 6821 chips these
are socketed and that's a super common
chip they're in like most pinball
machines so they're in the balet
machines and they're also in the
Williams machines they can be replaced
really easily they cost like five bucks
and um I've got a ton of them and
they're in a socket so it wouldn't even
be hard to do so I think he's correct
you could fry those no problem um you
could definitely fry them but to me it
would not not be an issue to replace
them if something did Prime I don't
necessarily see how the the in game
playay it would send electricity down
those lines anyways I'm sure it's
possible or he wouldn't be mentioning it
and going through all this trouble on it
and obviously they designed it in the
replacement board so they must had some
kind of issue going on
um now the reason I'm making this
distinction is because these 6530 chips
are unobtanium you can't get these um
because they have a ROM component so
they have to be programmed to the board
um so the only way to get these is off
of another Ali board so they're they're
valuable for that luckily
has designed a replacement board so you
can just take those three off put his
replacement board on there it cost about
150 bucks and it runs with new chips and
um has the code built in and no problems
the code on all of these games is
exactly the same um so if you did have a
parts board you could pull one of these
chips off and put it um on the other one
another interesting thing that I'll just
point out while I'm here is that this
board is running with see the 011 there
and then this one is a 11
one and this one is a 110 from what I
understand that's not supposed to work
either he's saying that it should be 9
10 and 11 but mine is 10 11 and 11 so I
don't know what they're doing there it
could
be that two of the 6530s are doing the
same thing but then that would make you
wonder why they had it with different
numbers so anyway if you keep going
through and if all this is confusing you
it's confusing to me too don't worry
about it so here's another Pia chip and
you can see that it does have a direct
connection uh to the edge the card Edge
but where they've added the diodes but
again those lines only go to the Pia so
if they did fry something it appears to
me that's all it could
fry um the 6530s seem to be completely
isolated so I'm not disagreeing with
them or saying I know better than him
I'm just saying from where I'm
looking I don't see the big necessity
for the 6530s although I agree that it
would probably fry the
6520s okay so here's another 6530 this
is the third and final
one
um they're isolated through these IC
chips that are on my
board um and
then these IC chips that are on my board
so there's no direct connection that I
see to the um to the Ed to the switch
input so I'm not that worried about it
frying the 6530s and luckily he's made
that board so worst case we could put
that board in there if it did somehow if
they somehow got
fried so all that to say I'm not too
concerned with adding those dodes if we
have a
problem I'll replace the
6821 and the the keep alive resistors
I'm going to leave the keep alive
resists because I'm going to leave
incandescent bulbs in it cuz uh LEDs are
uh evil and and anybody that puts them
in uh is going the wrong way and should
repent okay so um so I think that's good
I'm going to slide it back in and and
see if the if there's just a bad
connection on that one connector that's
making that game over light not work of
course I've replaced the bulb already
and I'm we're going to look at the
harness and see if we need to upgrade
those jumpers that he's talking about
that's a great idea this is also the
diode thing is a great idea too cuz they
did it on the later board so I'm not
saying you shouldn't do it
I'm just saying I'm not that concerned
about it I'll just replace 68 21s if
they pop any of them okay so back to the
cabinet all right we'll look at the
harness here in a minute um I wanted to
check this out so this is ic8 which is
one of the 68 21s and that's pen 10 11
12 13 and
14
um which just seemed like the easiest
way to look it up so on the
schematics you can't hardly read the
schematics so what I did was
was I Googled the pin out of a 6821
which is the same as a
6520 and 10 11 12 13
14 is PB 012 3
4 okay so if you go back to the
schematics it appears to
be 10 11 12 13 14 so it's these five
lines right here so here's the
interesting thing if if you look at this
this is a newer version of the
schematics so this is the schematics for
the revised Edition remember it shows
the diodes on it so if you go down
here uh wherever it
was it's the one with the diodes right
obviously so it's these
lines that are drawn
in with this weird crap
here where
those lines stay intact on the board but
they also jumper are off and are
connected to IC 29 and IC 40 it's kind
of hard to see but IC 29 IC 40 and so
one connects to a couple pens on
29 and then one two three four connect
to IC
40
right and then there's some more jumpers
etc etc right to get this all whatever
the hell this
is so those are running over to
IC
40 and IC 29 one's connecting to IC 29
four are connecting to ic40 and then
there's some bodge wires and stuff
that's a that's either a factory hack or
that's a somebody adding that part into
the design maybe because they liked it
off the new version or maybe they sent
out a little memo telling you to upgrade
it to
that ic40 IC
29 and then you can see the resistor on
the top of the chip there that's been
added so maybe this is a lost
Link maybe it's a lost Link
John couple resistors added there and
then if you look up here to this Pia
um so that's pin 1 2 3 4 five 6 7even 8
nine pin
nine is jumpered to pin
18 the trace is cut on pin
18 and nine runs down to I see
29 so I'll bet that's that
yep pin
nine pin I guess that's pin what do we
say 18 jumper together and they have cut
the trace that 18 was going to and if
you look on here now it only connects to
nine so they have modified this
board to be a little bit like the newer
version um
assuming that the original board
schematics didn't have that in place and
it doesn't look like it because it's not
wired on this PCB it's it's hacked in so
not sure what that does but it must be
something in the
code okay and this is John talking about
the CPU the 6530s in both revisions of
the mpu the 3 6530s are the same three
part numbers however these are 6530s 09
010 I mean 09 10 and 11 have to be in
their correct sockets or the board
cannot work I am again working on
replacement for these have the design
worked out now I'm going to run off the
circuit board to test should I have
results by the summer he did come out
with that board thank god
um
um the location for the 36530 is are ic3
is number
11 and that's what we have
ic5 is number
nine oh no wait I'm
wrong there's different numbers okay
that explains it all right I got it I
figured it out
John and ic6 is
10 all right so see how these are 6530
10 and
65301 this one obviously is a newer one
and you notice it says R3000
8-11 so that's an alternate part
number for
-009 so that's what's going on all right
well mystery solved thanks to John's
good research and documentation on the
excellent flippers.com website he sells
some parts for these too by the way okay
so uh back to the harness all right so
I'm looking at the harness and on this
green plug which is the top one one of
the
pins is like halfway
in so in the schematics it says that's
the DC
flash
wire which appears to be um the lights
on the um pop bumpers that come on
whenever the game comes on and then I
think the ones under the U kickers do
too
um so DC FL I don't know if it can Flash
it or what but obviously the thing's not
in there right so I'm going to go ahead
and replace that pin it's a mate and
lock pin um um also known as
amp uh so I think I've got the right
ones I'm going to swap that and then on
this one down
here you can
see that the bottom two rows only have
one pin he said if the middle row has
two pins you can leave it but if you
look these pins are not in the greatest
to shape so I'm going try to clean them
up and I'm going to spray some contact
cleaner on them as well um and by the
way that pin in the corner up
there that one that doesn't look all
that
great that is the one for the game over
light so that's the one we're having a
problem out of so I'm going to replace
it as well with a brand new one and see
if that gets us
going all right so a new PIN repaired it
luckily that was the second one I did
because it broke off in the tip of my
pin extractor so I can't do the upgrade
to the other two
yet so this thing you know you slide it
over the pin and then the pin slides out
of the Molex out of the back so you can
crimp a new one on so that's the tip of
that pin so it must have been heavily
compromised which means I really need to
do the power one because um they're
probably slightly
compromised so I'll get another one of
those you can kind of mess around with
it I can use a you can kind of screw
around with it and get them to come out
but it's just a big pain uh so that's
that so I think the other thing that we
want to do is I'm going to go ahead and
take this board off so we can resolder
some of it and see if we can get that
pesky four that turns into a zero to go
go away so that's
next we'll look at this closeup see if
we see anything obvious the connector
would be the most obvious place but it's
kind of strange that it only does it on
one they all look pretty
good well those aren't done done great
are
they come on
yeah I bet it's one of these top
connections on these
chips so there's there should be a via a
via going all the way through so that
the solder on the back soaks up through
it but
um if you get a flaky connection on that
it would do it for sure
[Music]
so a lot of these you know run to each
chip so it's not that it's one of the
control signals I'm sure if you mess
with these a lot you know exactly what
the control signals
are so those are resistors to that one
oh is there one for
each is there one for each see how these
so these are resistors these all go to
there these all go to
there these all go
[Music]
to
there yeah so there's a chip that
controls each display so in other words
this chip and these
connections are probably
it and then and they're
coming from these as
well okay so I'm going to just resolder
everything that looks like it goes
anywhere near that
particular display and then see if that
gets it more
solid so you can see the issue look at
that it wasn't put in there very great
from the factory so there was probably
one of them that was a little uh a
little off so I gave it some more juice
I just noticed it though after I
soldered it but I went one pin at a time
so there ain't no way I did come on
people you people you know I did how
could if I did one at a time I
couldn't I couldn't have done that if I
did one pin at a time it wouldn't have
lifted up like that it was something
that the factory did don't blame don't
blame me that was the factory all right
I think we fixed
it that seems to have fixed
it why are you why are you hitting
yourself why are you hitting
yourself look folks I can't make it
better than that okay um the other one I
I really do think it was cuz that chips
lifted up these other ones don't do it
so I don't think that's like a thing
that you run into with all of them and I
did resolder those pins but really there
was nothing wrong with them they looked
fine there's the ones that I haven't
resered um and it's a that P that
connector on the other side is just one
of those same big amp
connectors
so cool all right so we fixed that so
I'm going to put the cover back on
next all right so I got that back on I
broke that tool to remove the pins and I
I looked at the connectors on the power
supply a second time and we've got
issues there too that light that lamp
that lights up above the door is just
directly wired into the power supply as
is all of the GI and if you look they're
blinking you'll see them dim
here of course it doesn't want to do it
whenever I try to show it to you but
they're flickering a little bit so we
need to repin those as well so I got to
get another tool but I think we're
getting pretty far I had somebody
complain on the previous video oh the
videos are too long oh
you didn't fix the switches in 10
seconds look I'm just trying to film all
kinds of stuff on this particular one
because there's not that much about them
on YouTube so a whole video working on
just a few things examining what the
board is the upgrades that uh people in
the nose say you should do to it how it
appears to be designed differences in
the board all of this is interesting to
me so I hope it's not boring people too
much and luckily that guy left so uh I
hope you enjoyed it so far we'll be back
I guess there's going to be yet another
video as I uh keep working through it I
still need the flipper Parts the drop
Target and I need the uh I need to get
another one of those
um connector pin removers so that I can
uh repin some of the power supply stuff
but I think it's all coming together
pretty good um it seems like it's trying
to cooperate it's just the thing needs a
lot of work
it is however though I will admit that
we didn't have to pay much for anything
yet and in my opinion the board at least
since John makes that 6530 daughter
board the board is very repairable it's
just you there's a schematic for it and
it's laid out very easy it's easy to
understand it just dimmed it's easy to
understand how it's designed um so uh I
think they're they're definitely worth
repairing if you see one of these pick
it up so we'll see you on the next video
hope hope you enjoyed
it check this one out until then