Building the Catalina Wherry - Part 37 - Breasthook Pt.1

Nomad Boatbuilding
98 followers
1 Video View·Jan 14, 2024
My website: https://www.nomadboatbuilding.com
Instagram: https://www.instagram.com/nomadboatbuilding/
It's not about the money but living isn't free...
Here are some ways you can support this channel.
Get 5% off TotalBoat products here: https://www.totalboat.com/?sca_ref=3715732.xvvNNHFDPJ
Get 10% off Starbond Adhesives. Use the Coupon code NOMAD10
Shop here: https://starbond.com/discount/NOMAD10
Buy some merch: https://www.nomadboatbuilding.com/shop/
Support these videos with monthly or annual pledges at Patreon: https://www.patreon.com/nomadboatbuilding
Or make a one time donation: https://www.paypal.com/paypalme/nomadboatbuilding
Howdy Folks welcome back to noad boat
building I'm Mark Ruden and we've been
working on the sheer structure of the
Catalina wary the last episode we
fabricated our quarter knes and got
those installed and this week we're
going to move on to the breast hook now
this is going to take a couple episodes
to get through this part of the process
we're going to start by making a pattern
and then building a blank from which we
can fabricate the breast hook so why
don't you just sit back and relax let me
take care of the work right let's take a
look at making a pattern for our breast
hook so I've already done it on one side
of this uh piece of door skin I'm just
going to show you my basic layout
process so if I take this guy and what
I'm going to do is I'm just going to
square it up to the back face of the
stem here as best I can of course we
need to slide it till it's getting past
our uh termination point so I am going
to be taking it and be bringing this
breast hook right to these frame heads
one on the other
side
okay all right now we get in there with
our pencil shaped off on one side and
we're just going to reach right up there
and just Trace right along the edge of
the plank the Inside Edge all the way
till we hit that frame head and come up
and around
it okay now just to make it bit easier
to see I'm just going to use some
masking tape to outline these guys here
so I'm just running this on the outside
of
the of that plank line
there we
go same thing over here okay then here's
my the hunch my frame
end same over
here so there's our basic
information okay now one of the first
things I like to do is I just want to
establish a center
line and so if I take
dividers I'm going to just pick up this
point right here the inside of our
frame make sure I'm crossing my midpoint
with the
dividers okay and we're going to do the
same thing on the other
side oh darn
it not going to reach is it going to
reach barely yeah okay we just make it
we're going to do the same thing up
here where it met the
stem okay now I just drop a straight
edge on
there there we go we got a nice center
line now I know Joe
wants uh a fairly wide opening here um
that is he doesn't want me to take it to
a tight point he wants it fairly blunt
and I know he wants me to sort of create
something that's in the neighborhood of
a 12in opening so I'm going to just
going to start by marking out roughly
what 12 in looks like in terms of
width so I basically have two boundary
marks right there there's my frame ends
right
here there are 3/4 of an inch and then
I'm going to add in whales to those
those are going to be 3/4 of an inch as
well and I want those in whales to come
in
board by few inches past those frame
heads that's how they're going to
connect so if we give them
say I'll just rough that in this is not
going to be a finished design we're
doing here it's just sort of for fun um
so if I give myself say two give it two
and a half inches here I think looks
pretty
good do the same thing on the other
side okay so that's the point at which I
want my
in whales to
connect I'm going to bring
my this 3/4 inch mark up
higher a little L of whack there and
then the connection between in whales
and breast hook uh should be at a bit of
an angle and I would say if you Ed like
a 30 60 90° triangle and run it so you
get the 60 degrees coming off of here
this is just going to be for an example
here that's probably pretty good and
part of the reason that is when you want
to swing this this in whale in to fit
you want you want it to be sort of
closing a gap you don't want it Square
because that's hard to fit in there but
if it's got a bit of an angle then you
can SW swing it in and you can dial in
that fit quite
nicely do the same thing over here just
eyeballing it
in so the finished the finished breast
Hook is gonna have this hunch in here
this is basically filler behind the
behind the frame head and then the in
whale comes in here and it'll get
fastened through to the out whale out
there so from here I sometimes I just
like to sketch this in freehand so I
know Joe wants it fairly wide so I think
we're going to be taking a hard turn
here
already um of course you can get out
your ship sweep you can see if that
helps you at all if that gives you a a
line that you like
um generally I don't like to come too
flat in here just for looks but I think
for Joe we might have to flatten it out
a little bit just to make that turn as
graceful as
possible and so it'll come right
around that side so if I grab a French
curve for this I'll do this at the
French curve just for fun so I'm going
to say I like the way it looks in this
little stretch here say my sketch looks
okay so we're going to go to about there
and to call that sort of the termination
point and I'm going to mark that on the
French curve and I'll mark the center on
the French
curve okay usually I I tend to flip
French curves over to continue
lines so if I do
that I try and find that sweet spot
where it looks like it's going to
continue the line it's not going to work
out on this particular one well why
don't we try this
we'll we need to come into here this is
a hard point where the in whale meets
because it's not going to get any
thicker so we'll do that and it looks
like I need to sort of correct that a
little
bit I'll mark where that curve hits it
there yeah I think I needed to just
bring this guy out more so new center
line
that looks pretty good okay now to mimic
that on the other side if we wanted to
do that now normally I would I would
pretty much all just make a template out
of half of this and then mirror it on
the stock but for whatever reason you
wanted to make a full-size template what
you want to do is carry some of these
marks over here in order to mimic them
exactly so we have our Center Line mark
on the on the French curve if I pick up
say
this Mark over here how did this line up
yeah okay so it lines up with this blue
mark on the French curve so if I pick up
that point and I swing it over
here okay and then I come down here I'll
just leave the compass set the same put
the uh pencil right on that same point
find the center line there bring it over
swing it over to this side now I've got
a point that matches over here so if I
put that on the center line bring my
blue mark That's happens to be on the
French curve already over to here draw
that in there's my first point now I
know this guy basically fares through I
had a mark right there it's the same
point bring that over swing that over to
here now it might not be 100% on the
money but it gets us in the
neighborhood now not sure I totally love
that but it's it's a fair enough place
to start and once it's all put together
I can always sweeten up this curve a
little bit by eye by just working into
this the spoke shave and getting it down
to where I want it so there's just sort
of basics of laying out breast hook
patterns um we'll draw in our hunch here
that would be there this is our
basically our
blocking the frame comes in right there
so all of this inside is the actual
breast hook
we chop that off right up the center
line and bear in mind this is marked
right at the shear line so and all the
bevels sort of dive down so when you're
actually making these parts you probably
need to expand this line about an eighth
of an
inch but you can least start on the on
the on the wood laying out this pattern
at an eighth and a inch an eigh of an
inch onto it or calculate exactly where
that bevel would be so if this is the
this is the uh planking sides and our
breast Hook is coming straight across
and we want a little bit we want it to
come a little higher in order to cut the
crown into it so there's our breast hook
material we need to know what this
distance is right
here and that's the amount that you
would expand this line over here of
course you'd be setting your band saw to
this angle in order to make sure that
your finished line lands right there and
of course this is a tapered fit so even
if you're out by a little bit there's
some cutting and fitting to do and
because your all wider on the top you've
got wiggle room you're not starting out
at the actual Shear line and having this
thing drop down you're starting up above
and you're working it down until you get
your fits looking nice all the way
around and then you're done and then we
carve off the
crown you could do that top and
bottom there's a way of just faking the
bottom in you only need to sort of work
the bottom Edge back 3 in or something
like that or 2 in you make it look like
that's got a crown on the bottom even
though it's dead flat across on the top
of course though we would fully shape it
so that it's got a crown all the way
over on the top of that breast
hook we have the shape of our breast
hook designed I'm going to take this
pattern and I'm going to split it down
the middle we don't need both halves of
it for the next stage of this
process
this mahogany door skin has got a very
loose grain and so I find it helpful to
just in size along my pencil lines with
the utility knife it just gives me a
cleaner result now we're just going to
trim this down to shape and clean up our
cut
so I find as I've gotten older my eyes
have gotten older and in certain
situations I'm finding it harder and
harder to see pencil lines especially
over at the band saw when I'm cutting
curves and so one trick I've come up
with is just using some masking tape to
accentuate my lines it's just easier to
see exactly where that line runs and
especially when you've kind of sketched
out a fudgy line like I have here this
really helps to refine it and so it's
easier to do this than to start erasing
and trying to draw a line in
Darker now do I really need to be this
fussy with dialing in this particular
pattern no I don't but I like doing it
it helps me figure out where I'm going
it helps me get into the zone now
there's a lot of steps to come between
making this pattern and shaping the
finished breast hook so I realized that
this might change a little bit along the
way but that's fine I never feel like
I'm wasting my effort with task like
this because the more I do it the more I
have a very clean refined idea as to
what I'm looking for in the end and when
I have a pattern that represents that it
helps me from going astray along the way
all right we've got our breast hook
pattern made up here
now so now to get it out of this stock
I've got two different pieces of oak
here to work with um I think I'm going
to go with this one this is clearer but
uh it's all sap W down there I don't
really like the way the grain kind of
runs off at this sort of a little bit
more of a drastic angle on this one than
on this this was the grain's a little
straighter so what I need to do uh
essentially is I use um layout two
pieces one that goes this way and then
we flip this over and one goes the other
way and when you bring these together
one of them flips over and we get a book
Matched not exactly book Matched cuz the
grain reverses on the other one
but it goes the other way and we uh and
what I'm going to be doing to get the
crown to because this is only an inch
and a half thick and I need a little bit
more uh thickness to get the crown I
want we'll we'll put the two together at
a slight angle I'll show you in a minute
how I was playing around with that now
one one thing I note here is that um I'm
very very tight on width it just barely
makes it and I know once I've crowned it
I'm not going to have enough width so I
have to actually do one of two two
things either I need to add a strip of
material down the center or I need to
add some to the edge and while it's
really common to throw a stripe down the
center I've never really liked it I've
done it but I also feel it looks a
little bit cheesy I'd rather just see a
single seam so I think what I'm going to
do is I'm going to glue on about an
extra I don't know half inch or 3/4 of
an inch onto the edges of this and I can
in the end I'll you know prior priortize
this obviously is going to land right on
the seam and we'll have a little bit of
extra that shows up on the outside it's
not really a huge deal and I don't think
it'll show nearly as much as having a a
strip down the middle so we'll do our
best to try and make the grain look like
it's continuous off the one Edge and I
got to figure out how I want to best do
that this particular plank here has got
a bunch of defects this is sort of a bit
of a naughty spot there and there's a na
naughty spot there and normally I would
probably try and work around those
because that's a perfect opportunity to
sort of get rid of this ugly bit you get
to use the rest so I can get one out of
here and I would flip it over and get
the other one out of here and it works
around these two knots I'm just going to
lightly sketch in where this might go
and of course we got the tail end here
which is always a bit junky at the best
of
times so looking at it from the side
maybe I get one going there and then
flip this over I guess that wouldn't be
too bad clears this one pretty good
green looks okay and you should always
make sure you're looking at like the bad
side so this is the good side here just
looking at how the rough that that sort
of naughty area is down
there it's going to make working on that
a bit
difficult probably better off bringing
that
forward so if I were to go
there
oops flip that
over that one would go
there that's not so bad so I could buck
that straight off there and I could
joint this and I could peel a couple
strips off that could glue onto here
hopefully it'll looks like it I might be
able to match up the grain pretty good
by taking a piece of this one here and
bringing it up taking a piece of this
one there and bringing it
over yeah I don't dislike that
idea could try doing a rubbed joint I
know that's not going to work as a
rubbed joint cuz these uh these cleats I
made up here have got a little too much
spring in
them they don't lie dead
flat but they do come up flat when I
clamp them so here we go if we do that
check both surfaces make sure
we're
fully
glued
okay that'll work I'm going to throw
clamps on but just to hold this in place
for the moment I'll use some pinch
dogs now while I fumble around with
these pinch dogs I just want to let you
know that these videos are supported by
my followers through patreon if you like
these videos You' like to help me keep
making more of them I encourage you to
join me on patreon you can find links in
the corner down in the description this
week I want to welcome safety Sam into
the fold thanks for joining up Sam I
really appreciate
it and not doing anything fancy with
this joint because in the finished
product there's not going to be much of
it actually in the in the boat I mean
they it'll be there but everywhere that
it will be
employed uh there'll be Fasteners
passing right through it so it's acting
more like Feller than anything
else
pinch dog on again just to keep it from
running away on
me so pinch dogs can be amazingly
productive especially if you're working
with say something that had a a sprung
joint almost like this is like you can
know this one's popped out here but you
can see how if you had some Crown in
your cleat that you're putting on there
it would just act just like a clamping
call and just help hold it all in
place
that'll
work this is where I wish I had one more
clamp exactly like this one cuz I I hate
mixing clamps out it's a
weird type A personality type thing and
I'm not really a type A personality
which is funny
thing at least I don't think I
am there we
go that's good so we'll just put that to
the
side don't need pinch dogs
anymore and we will
will return to this
tomorrow and cut out our breast H and
glue that
up do a little mop up with a rag here in
a
minute I'm playing around with deck
crown and uh I started out with this
which basically represents a piece of
inch and a half stock which is what
we're working with rough um but I wasn't
getting enough Crown in there I didn't
like that so I grabbed something wider
and this is representing what it would
look like if
I cut my stock if I join my stock in the
middle at an angle and it gave myself a
little bit more height and what I was
doing is taking a um taking a piece of
wood like this and clamping it hard on
the gunnels and trying to get a good
idea as to what this angle would be
right here if this shape were to carry
across and of course it as it's after it
starts heading off in this direction it
starts to curve towards the other side
so here are two different crowns that
I've described onto this piece of
material uh just trying to play around
with what I think is going to look best
in the end
um you tend to have to go a little more
extreme than you think in order for it
to not look flat we'll step back and
have a look at it from a greater
distance and actually as I come back
what I do notice is the higher Crown
feels like it's going to follow the
sweep of that Shield here a little bit
better so I think we'll go with that
we're going to go with the higher Crown
the way I'm going to figure out the
angle I need to cut the material at I'm
just taking this which represents or we
could use this for that matter which
represents our actual uh stock width and
I can just lay this on here and swing it
around until I've covered off both ends
of this Arc so I know that I can get
this Arc out of this
material and I can certainly just draw
draw these lines on
here and that's showing me exactly what
angle I need to have
my stock cut at or joined at in the
center
line so I just pick up that angle cut
that onto my stock glue it together and
then I'll at least I'll have a blank
that has this representation here that I
can then create my finished shape out
of I'm going to do this
that's the angle that we'll use for
cutting our stock
at and so that I don't lose that and
it's going to flip this over
here and we'll just Mark that like
so now we're going to rough cut the
stock for making these breast H so I
just want to start over on the band saw
this is the safest way to knock apart a
big piece of Oak like this
band saws aren't really subject to
Kickback the way a table saw is and so
whenever I'm running heavier denser
Hardwoods I like to do as much of it on
the band saw first before I go to the
table
saw and I've learned that from James
krenov actually if you read his books he
highly recommends using band sawce over
table sawce for as much as
possible all right I'm gonna cut this on
my sled I think I've already adjusted my
angle here now uh to line up this cut
with the blade I just came up with an
idea I've never done this before I don't
know if it's a great idea or a terrible
idea but I put the straight edge on here
and we want to use a straight edge
that's pretty accurate in terms of
laying nice and flat of course you could
always use a you've got a stick that's
really accurate you could use that too
that might not be a terrible
idea let going see if this will do a
better job
okay so laying that stick across
there I should be able to just dial in
my stock
position that looks pretty
good all right set my stops that looks
good
there looks good there
okay I should just put a block in here
to keep it from sliding so got to find
something for
that okay so that's all
there that looks pretty good okay let's
see if this
works
[Music]
[Music]
okay so there's that one so that's going
to be this side it tips up like that
when we're done so of course I need to
make sure the other side does the exact
opposite and so that means I cannot use
the same jig setup for both operations
so put that to the side so we'll do the
same
thing except this time we'll just run
the stock the opposite way so I think
this worked out pretty good it wasn't it
was off by just a hair
not exactly sure why it was it was like
it cut a bit 16th about a 16th stronger
than the line it was laid out
to
so somewhere there's a there's a flaw in
my thinking and I just don't know
exactly where it is but the flaw is
pretty small so I think I'm confident to
use this
again okay that looks
good there nothing to stop it from
sliding forward so I need to think about
that let's see if this guy is capable of
grabbing
it not
really okay we need a different hold
down
right that
works
okay that'll
work
okay that worked really well now there's
a reason I was fussing around with this
particular piece more than the other and
that's for safety reasons what we want
to do now is cut a slot down in here in
order to put a spline through this
breast hook in order to give ourselves
Extra Strength now we could also use
biscuits in here that's a great way to
go but I I like splines splines are nice
and simple they're easy to glue up and
they're a good reliable joint that you
can have running all the way through
there carries lots of glue so I think
we'll just go for basically like a
3/8 wide spline I think that's plenty so
I'm just going to throw a single e inch
cutter in the
middle and I'm not even going to measure
it what I'm going to do is I'm just
going to cut the spline to match the
slot that's the simplest way to
go whenever I'm tightening table saw
blades one thing I never do is I never
grab these with two different hands and
and try and force them one or the other
I use one hand on one and I'll just push
with my thumb or something like that on
the other or squeeze these together if I
have to and that's because it's really
easy for these to slip off if you're
using two hands and I've slipped before
and carved myself up on the blade itself
that way you only need gentle pressure
to clamp these down you don't need this
to be super super super tight but
because the spinning action tightens the
nut that's the way it's set up okay so
now I want to figure out exactly how
deep this should go just go 3/4
basically whatever
your thickness of your spline is that's
about the depth you need and that that
should give you more than adequate joint
Okay now what's my spacing so if I look
at my pattern here what I did before is
I just laid my ruler on here into the
looked at the my finished shape and
eyeballed we is going to
be draw on either side of my ruler my
ruler is 38 of an inch thick we go like
this and square it off going to get a
spline that's something like this going
right through so if I take a look at
this I get nominally a half
inch from either Edge so we'll just run
this a half
inch one of the reasons I love these
Carpenters rulers are these
convenient thicknesses that we have
built right into
it so that's going to be the cut right
there and I need to make sure I run
the the acute Corner against the fence
so this one will run this way the other
one will have to run the opposite
direction
[Music]
[Music]
all right here's our finished part we
might a spline up here just some more
Oak drop that in
there of course if we try and slide
these together they're not going to fit
because these are intended to
be raised up at a slight angle so if we
put those together now look at that
that's a nice tight joint the spline is
uh just about perfect we want we we want
the alignment this way to be not not
super super tight cuz we do need to get
glue in there but uh reasonably tight so
that this ends up a consistent joint we
don't want it so sloppy that these are
jumping around and then this fit this
way can be a little bit looser just so
that we don't get uh pinched in here we
don't want to be fighting to try and get
this joint closed so just a little bit
of slop in the width of your spline is
not a terrible idea this one feels like
it's right bang on the money so I think
I'll prob probably even take a couple
swipes at it with the plane just to
reduce it a
hair but aside from that that looks
really good if we end up with a slight
glue line down here that's not really a
big deal because it's right down on the
center line we've already got different
grain coming together having a a line
down the middle is not going to be uh
unsightly I don't think but for the most
part that looks great now I didn't do
any cleanup on these joints I felt like
we got a pretty good finish from the
table saw and those saw marks are going
to help us with our glue joint we're
going to put this together with epoxy
and that's because there's so much more
endgrain in this joint that epoxy is the
better choice for it we did the tight
Bond 3 for these other areas because
this was all face grain not end grein
tight Bond 3 or any of those PVA style
glues are really good for face grain
they don't work great for end grain but
epoxy does so that's going to be a
really nice breast hook right
there now my only only debate was
whether or not I should be cutting any
of this out ahead of time but I think
I'm going to say no I
think um I think I'm just going to get
this glued together and worry about
doing this the cutting out here a bit
later the biggest issue is going to be
what the joinery looks like down here
where it meets the side planking but um
I think if I can get this all fitting
nicely and then I'll worry about the the
end cuts and and if I have to do this
stuff more or less by hand that's not a
big deal I pull that off all right that
looks great let's get this glued up and
we can move on to the next job okay
there we go we got our blank made up for
our breast hook I'll have to get that
glued up before the next episode so
please join me again next time on
building the Catalina wary see you later
folks
