Building the Catalina Wherry - Part 50 - Finish the Cap Rails

Nomad Boatbuilding
98 followers
1 Video View·Jun 3, 2024
welcome back to Nomad boat building I'm Mark Ruden and we are back working on the cap rails for the
Catalina wary in the last episode we laid them out we cut them out and we did a little bit of joinery
today we're going to do our final fitting of those Co rails so let's just get right into it fire away
[Music]
[Music]
that goes about
[Music]
there nice no steam required that's
awesome what I might do is just shift it Forward scribe a line underneath following the sheer line
clean that up but then we'll shift it back to overcome the roundover will put on here and then
I can use like a flush trim router bit to buzz off the inside and that way it'll just be tight to the
to the in whale on the inside and just proud on the outside I kind of like that detail I think
that's kind of cool now that my scarfs are fitted together it's time to glue them up I've done that
directly on the boat by putting a bit of wax paper underneath the scarf area now I find this to be a
very effective way to glue Parts up because even if the joinery isn't perfect you can make sure
the whole part is aligned to the boat properly and the glue line will make up for any discrepancies
in the joinery especially in the case of a hook scarf like this one can make the argument that
a heavy glue line will actually accentuate the joint it's not my personal preference but it's
acceptable so I came up with a plan to finish the shaping of these cap rails
directly on the boat so I've already cut them out to my original pattern
that was the same width as the gunnels now I'm going to trim them to match the
outside Contour of the rubber rails using a flush trimmer rotor bit [Music] [Applause]
[Music]
in the previous video I discussed ideas that I had about detailing these gunnels rounding
over the corners but then I realized that these cap rails are so integrated with the
shape of the gunnels that I needed to sort those out first so now that I have the cap
rails in hand and I kind of know where I'm going with that I can move on to
shaping the rub rails themselves so I'm going to start by giving them a generous
half inch round over on the outside top Edge we'll deal with the inside corner in a bit
[Music]
oh oh
[Music]
with that round over done I'm going to establish a distance that I want
to offset my cap rails from that rounded Edge then I can set my CA rail back in
place we'll mark it and then trim them down to size on the band saw
we're just going to trim it a little outside of our pencil lines cuz after
that we're going to go right back onto the boat and get our flush trim rer out again
oh [Music]
oh [Music] [Applause]
[Music]
now with the cap rails flush trimmed to the inside face of the in whales we can move on to the last
little bit which is detailing the top inside corner so I'm going to start by putting a small
round over on the cap rail itself then we'll move on to the rest of the shear line [Music]
[Music]
now I've left the Capa rails in place for this operation because I want to stop this little
round over just short of those cap rails I want that roundover to basically kind
of Fade Out then the cap rails are going to be flush with the inside of the in whales [Music]
[Music]
[Music]
okay I'm going to make some orlock pads for the boat I'm not going to do the
whole process but we'll look at some of the details here so I've started out by drawing
myself out a full scale drawing of my in whale and out whale construction and my
my rail caps are indicated on there and I've used uh the actual or orlock here to try and
find how I wanted this to sit in here so of course these this is showing it on end so
your your Hardware will be turned on in but I'll just lay it sideways here for the moment and Joe
wants me to sort of try and angle these towards um level as much as possible which is pretty
doesn't I don't have a lot of wiggle room I've only got 3/4 of an inch here and an inch half
inch thick um orlock so I I can only get a couple of degrees two three degrees maybe of
angle in there so I got to be careful that I'm not this isn't hitting the planking is
is what it boils down to so I've worked out a basic design for what I want that orlock pad to
be I've got my stock here it's a little over thickness right now and it's a little over
width and I'm just going to start by making my mortise for my orlock itself so I started out
by doing some test holes uh first taking the diameter of this uh socket here and matching
that diameter I just what I what I get is I get it's a nice fit but it's too tight
it's it's like you're never going to get this thing sitting down properly like that
so I've had to step it up to the next size up which makes a little bit on the loose side but
I could always do a an epoxy fill to bring it up to 100% it's not touching the bottom of the
hole but notice how it's rocking around and that's because this little this little radius
here in the flange to fix that in order to fit these we need to just do a little bit
of a chamfer let's do a small chamfer and it's getting closer just a little bit more
and now see it doesn't really rock around quite so much and I want to just chamfer it out just
enough so it doesn't Rock but not so much that the edges of this hole show past the the side
of this piece of Hardware anyhow that's what I've done down here and so now I want to Mark
these out in order to do the mortising and we do want to mortise this down into the orlock um some
people will just Mount them flush on top and yes you can do that the only thing holding it there
then are just the screws I like to set it down into the orlock pad so that this whole the whole
flange here is locked in and that's holding it in place and that means the hardware the
screws that are holding this in are doing very very little so here's a little trick I came up
with um first of all we're just going to make sure we in we Mark each of these guys for the
uh part that it's going to be fitted to cuz they are never exactly the same so this one goes with
that one and I'm just going to indicate I've got some markings on here telling me which side is
which okay and so I'm going to use this Carriage bolt in order to just lock
this on here I've done this many times just holding it in place or I've tried
clamping it in place which is also a bit of a pain cuz the clamp is always in your way
okay I've also just tried pre-drilling for the screws and screwing it down that works
okay too but this is something I just came up with today and it works great
so just tighten that up a little bit that cage bolt holds it on just perfectly firm
enough I'm just going to use a square here just to make sure that we are Square from
side to side there are some people that will mount P these at an angle so that the screws
are not falling into the same grain path as each other I don't really like the looks of
that and I don't really think it does a hackup a lot for you take a nice sharp
knife now and we carefully insize around this so I'll start at a corner and work my
way back not going all the way to the end because you'll always overshoot a little
bit like so
flip that
over then I'll do the same thing the long ways and you got to use a light touch
when you're doing this along the grain because the grain will pull your knife
off its Target if you don't use very light Strokes to get get it
started we don't have to go crazy deep you know if I get down a 16th or something that's plenty
I don't even really need to go that far and you can't trust these castings to be
consistent they're going to be out of whack because of the finishing process
so you have to make these individual you could make a universal jig I suppose but
anyhow there we go so now what I like to do is just do a little
bit of inzing with a chisel so I'm just going to take out the tiny bit here like
this just chipping out a hair we'll do it both sides and I want to make sure if I
insize this way that I don't overshoot my P knife line so I've got to follow the knife
line and I could uh I may just deepen that a little bit in both directions and of course
then we also want to do it this way too and the reason for doing this is this just makes
it so much easier to see what you're doing I'm going to use a router to excavate this little Mor
and if you protect your edges by just breaking a little chip away like this
and when you're using the router you can just hold back from that edge by just a
tiny little bit and then it's easy to clean it up to that line by hand
afterwards just like
that so note how I've left all these or blocks attached to the same stick I haven't cut them
into smaller pieces it's just way easier to hang on to the work while it's long like this and it
gives me the opportunity to change the length a little bit if I decideed it doesn't look quite
right I generally like to sneak up on the line working my way around in little circles like this
I don't know at least for me this is the way to do it that that feels safe of course you always
got to be worried about the the router climbing in the wrong direction on you so I take it slow and
easy all I I'll hang back from the line too that's why I do this inzing with the
Chisel all the way around because it makes it very easy to see where that
line is pencil line will just disappear but that chisel line is very obvious and now with
just a little bit left behind maybe not even a 16th it's really easy to clean up to the line
for
for
we've got our blocks roughed out finished the
mortise marked all our directions so that we get it all fitting together the same way each time
so there's a reasonable fit there's just a you know there's a whisker of space showing around
that it's almost impossible to avoid if you make it too tight you can't even get this thing in and
out so um that's done now we just need to come up with our final shape so I've started by just
blocking this out as per my drawing reducing the top down to the narrowest possible width
just to reduce weight visually there's plenty of strength here I've got some funny angles on
this particular orlock pad just because we're trying to pinch exactly where that hole lands
and there's only so much room on that the gunel cap so it's coming out this shape but anyway we
need to reduce this down to something that looks attractive and so what I'm going to do
is I'm going to just give myself a a healthy about a 5/16th lip on the ends and let's see
what we'll do we'll give ourselves say 3/4 of an inch on the top there that'll be just flats that
remain and I'll just use one of my sweeps here to connect the
dots we want just a little bit of a concave to it doesn't need to be a lot but a little bit makes
it look so much more elegant so we'll just draw that on there and I'll repeat it on the other side
okay so we're going to cut this so it's Square to the bottom and I've right now
I've got this angle square but this one has a this one this angle drops
off on the back side so the result if we look at one that's already cut
here is when when we run it through the band saww like so with a plum cut this comes away
and our shoulder here sweeps out as a result of the the Oddball angles I'm going to leave that
alone because I think that actually looks kind of attractive having this this uh nonrectangular
shape up here but in general we would usually just have that being sort of a square cut you'd soften
all this up a little bit leaving a bit of a hunch here and sometimes if I going to glue this down
I would probably just have these T taper out to nothing feather them right out but these are
going to get screwed down so we need some meat and um I'll probably add a little champer onto
these edges as well just to soften those up but we'll do that by hand there's one last thing we
need to do and that is add the shape to the inside and outside so I wanted to reduce as much material
as possible for that now I did one thing that I I screw it up and I when I trunked this whole shape
I forgot to leave an allowance for the concavity on the back side here so I'm I'm stuck with this
width at the top but what I might do is I might just take it to the to the sander and
just Whittle away the back edge here leaving it square up here and just taking away all the
material down lower to get that concavity it'll trick the eye into thinking it's there and up
here at the top we won't really notice it so much and of course on the outside it's got a
convex shape so that's easy to do we got plenty of material to work with for that once we get
it all roughed out then it's just a question of sort of tweaking it by eye until it looks nice
[Music]
sh
sh
well our warlock pads are done I think they look pretty good
got a couple degrees of slant to the inboard side which is what we wanted
[Music]
my orlock pads are done and I've fit them in place I've boarded the holes through for the
or loocks to pass all the way through the gunnel structure um I wish I had sort of planned ahead
a little bit better here it's standard practice to put solid blocking anywhere your or locks are
going to go I didn't do that I don't know why I really don't know why um um but I wish I had this
worked out fine in that my orlock is going to pass all the way through it's going to pass all
the way through here and there's it's solid all the way through so there's a ton of support for
the orlock here to to to Bear against up forward it hits one of the voids which is not the end of
the world because I think the orlock itself is big enough it's got the the the cap rail underneath it
that it's connected to so there's like an inch a good solid inch of um Oak below the orlock itself
to help support it so I don't worried about that but up here where my screws pass through on the
outside ones at the very least I've hit a void you can see right here my screw hole just clipped the
planking a little bit I was going to make these shorter screws so it's not the end of the world
but still it uh there there's no holding there same thing over here just skim through it so
I need to put in some blocking at least halfway through that through that hole right there same
thing over here I might just try and block in the whole thing actually this hole is going right
through this blocking that's already in place so that's great that's super solid and there's plenty
of holding where these other screws go through the in whale so I'm going to have to pull this
cap rail off and uh put some more blocking in here and before we're done we'll have to redrill
a couple of holes to make that all fit together I really should have just put a little bit more
effort into thinking about where the stuff was going but I didn't really do that which is a
mistake so um I'm going to be paying for that and the fact that I can't really move ahead with my
finishing operation which is what one thing I was kind of hoping I would get on to today but
nonetheless I mean that's just the way it goes sometimes you can't think of everything ahead of
time so we'll just pull off the cap rails We'll add a little bit of material and
we'll be back on track tomorrow okay well there we go our cop rails are done
I hope you'll join me again next time on building helina wary catch you later folks
