Building the Poulsbo Boat - A Modern Take on a Classic Wooden Boat - Episode 1

Nomad Boatbuilding
98 followers
#WoodenBoatBuilding
#BoatLofting
#StripPlanking
#TraditionalBoatBuilding
#BoatDesign
#SmallCraftDesign
#WoodBoat
#BoatbuildingTools
#DIYBoat
#WestSystemEpoxy
#NomadBoatBuilding
#PacificNorthwestBoats
#Lofting
#BoatPlans
#HandBuiltBoats
Howdy folks. Mark from Nomad Boat
Building. We are I CAN'T
Is there like a smudge on the lens like
right around there? I can't tell. I
can't tell if it's on my glasses. Oh,
they're pretty dirty. That could be.
[laughter]
Oh man, let's get it together. Okay, so
here we are at the beginning of a new
project. This is the PSBow boat. It's a
sport [music] fishing boat that was used
in the PSBO, Washington area. developed
I think around the 1950s roughly. They
were [clears throat] typically carvelt
built that is uh cocked planks. [music]
They usually had an inboard engine. Had
a good reputation for being a good boat
for around here. You know, could take
some rough water and be a good platform
for sport [music] fishing for salmon and
such. So, we're going to be building
this as a strip [music] built boat.
Nominally, I think it's going to be
1/2in planking glass inside and out. And
this is going to be propelled with an
outboard [music] as opposed to an
inboard engine. And we've been back and
forth and back and forth with so many
different options. [music]
And uh we went for like this very
elaborate setup at one point and we've
scaled it way back to pretty much no
interior whatsoever except for a single
[music] thwart across the stern in order
to run the outboard. And the rest of
it's just going to be kind of wide open
so he can uh get in there and he wants
to fly fish [music] from it. It'll just
be a big non-skid floor inside. We're
going to be doing some fairly
substantial gunnel construction on
[music] there because I just quite like
that. My plan is to put in a thart riser
that runs the [music] full length such
that should he change his mind about the
interior, want to start adding
components later on, it's a simple
[music] job to do that at that point. We
can just build off of that thwart riser
that'll be running the full length. At
least that's my plan. And so I've
started out with doing a little uh model
of the strip building. Just wanted to
[music] see how it would plank up. And
I've I've come to the conclusion it
worked pretty good. Except as [music]
we're getting up towards the keel, I
decided it would be better if these
strips weren't winding down and twisting
[music] under the stem, but wrapping
around towards the keel faster. So, I
think I'm going to add a bunch of sealer
planks as we go. basically long wedges
that are going to start spreading
[music] that planking out up forward
such that the last few planks [music]
instead of twisting down onto the keel
are going to run uh you know as a sort
of a big C-shape [music] here. That's my
thoughts. I think we're just going to go
with square edged planking. Um no
beading cove on it cuz it's just a time
killer and I don't think it really needs
it. And we're going to be edge nailing
the planking as [music] we go as well.
So, my next job is to start lofting.
I've built my strong back already, and
I've done that because I'm going to
build my lofting board on top of the
strong back. The last boat I lofted, I
did it at at that height, and it was so
much more comfortable. I'm getting too
old for crawling around on my hands and
knees, so I decided to [music] to sort
of change up how I do things a little
bit. And then this table of oets doesn't
have any information for the [music]
stem, so I'm going to have to pull that
off for the drawing. and it's got no
[music] information for the transom. So,
I'll have to pull that off the drawing
as well. And happily, this drawing has
got a scale drawn on it, so I [music]
can work from that using dividers. When
I I printed this out full size, but
[music] it still didn't come out quite
right. This these should be clean 1- in
long uh divisions here, and everything's
printed out just a hair smaller than
that. So, the simplest thing to do is to
just work off of the scale here as
opposed to trying to measure off of the
drawing with a ruler or anything like
that. That's the whole point of this
scale is you can pick up dimensions
there. They're accurate to this scale
right here. So, some of the videos from
this series is going to be sponsored by
West System Epoxies. Uh because it's
because we're going to be doing a pile
of epoxy work in here, for instance. So,
I'm looking forward to that. It's going
to be a great sort of platform in order
to feature some of their products. And
if everything goes well, you know, we'll
have this launched in the spring. I've
estimated about 410 hours for the whole
project. That factors in about 30 hours
for a a canvas cover I have to sew. So
hopefully my numbers are correct. I'm
making this little model is uh was just
quick and dirty. I didn't labor over it
any any length of time at all. And I'm
not trying to make it look neat and
tidy. It's it's quite sloppy, in fact.
But that's just fine because my whole
goal for it was to investigate how this
would plank up using some little strips
that are relatively close enough to the
finished size. I think they're a little
oversized in fact, but um the general
premise is there. Every time I don't do
a model at the beginning of a project, I
usually stop and do a model. [laughter]
I usually find something I want to pull
off of a model. And if nothing else,
this is a great way to figure out
exactly, you know, how long is the
planking that you need. So you can take
a bat and wrap it around the model and
then lay it off against a scale and
figure out, you know, how much longer it
needs to be. So I've already established
that this 15 ft boat nominally needs 16
ft planking. So if I can get like 16 and
some change, that's even better. Okay,
folks. Now we're going to tackle some
lofting. A little process that I like to
refer to as juggling spaghetti. Lofting
is the process of taking your table of
offsets from your plans and recreating
those full size on a lofting board. So,
we're basically drawing the boat full
size in four different views in such a
way that all the lines that we create
are accurately interrelated and
coordinate with each other relative to a
grid work. Imagine like you're creating
a wireframe for animation. For instance,
we're creating a wireframe, but we're
doing it two-dimensionally. Now, I'm not
going to be hitting on the entire
lofting process here. I'm just going to
touch on a couple points that I think
are useful to know. These couple of
concepts I want to convey are important
because they get us from having a
two-dimensional drawing of our boat into
our third dimension. The really
important information that we need to be
able to build the boat. Okay, so let's
just jump right into it. My lofting
board is just a light framework made up
of roughly four or 5 inch wide strips of
plywood. So, I reuse these and bundle
them up when I don't need them and pull
them out when I do. So, they're just
screwed together. Even when I'm working
on the floor, it helps to have this
slightly elevated frame. So, I'll lay
that on the floor usually and then shim
it up so it's nice and level. But here,
I just screw it all together and put it
on top of my strong back and add a few
legs to it. Then, I cover it in 3/4in
plywood. That provides a good solid
surface for the nails to hang on to. And
once that's all fastened down, I cover
it in another layer of plywood that I'm
going to draw on. In this case, it's
just 1/4 in pine that's been painted.
We're into the lofting. And the set of
lines I have is a mess. Not thrilled
about it. It means that I have to make a
lot of executive decisions. Like right
off the bat, the shear line was woo all
over the place. If there's any line you
should get right if you're measuring a
boat as it's the shear line and it was
terrible. So the way you deal with it is
you just have to do your best to fair
out your initial lines and those become
master lines around which you build the
rest of the design. So there's a point
at which I'll be kind of departing from
these lines drawings al together for the
sake of the information I've put down.
So, what I've got down here is my
primary water line, which is the one
that sort of bisects the hall nominally
in two. It's water line two in this
case, one that runs right through the
middle here.
And so, I've fared that out and that's
going to be kind of locked in when I do
the next views. I'll be using that as
sort of a primary benchmark around which
I'll juggle the other lines. The same
thing with the shear line and the rabbit
line. Those will all stay. and then
everything else sort of gets manipulated
in order to suit those. That's really
the only thing you can do about it. So,
what you're seeing me do here is I'm
having to juggle battens because my um
regular battens are too stiff to make it
around this bend. Very beamy in the bow.
Look, it's a cod's head mackerel tail
hull form, which means it's like big and
bulbous near the bow and it leans out
towards the stern.
So, I thought I would quickly talk about
tools you need for lofting. One of the
first things we do is lay out a
perpendicular line in order to create a
grid for our lofting. And to do that, I
use tramls. So, this is essentially a
compass or beam compass. Just attach
this to a stick. You could just use a a
stick with a finishing nail as a
fullcrumb on one end and a hole at the
other end that you can shove your pencil
through to scratch a couple arcs. And
the idea is we take the where we want to
put our first perpendicular. We come a
set distance out from that using the
traml which will be our usually our
first station spacings [snorts] and then
strike a couple arcs up in the sky and
connect the dots so that we get a
geometrically accurate perpendicular
line to our baseline. Once you've done
that, we take a tick stick, which is
really just a piece of wood that we lay
down along the baseline, and we mark our
station spacings along that, and then we
carry it to the top of the board and lay
those off relative to our first
perpendicular. And we connect all those
dots. And that just ensures all of our
stations are nice and parallel to our
accurately laid out perpendicular line.
These are really important elements. You
can't really trust a rafter square to
provide these perpendicular lines for
you because rafter squares out by a
little bit that will grow these lines in
ways that will really come and kick you
in the butt later on in the lofting
process. So accuracy at the beginning is
exceedingly important. So the other
thing we use throughout most of the
lofting process are flexible battens and
typically I have one or two that are the
full length of my lofting board. usually
about half inch square in cross-section
and made out of yellow cedar and red
cedar. So those two species are usually
I can get dead clear, which is really
important. You want a really fair batton
that doesn't have any kinks in it or
wiggles in it. You really want a variety
of them. So these are just a couple
shorter ones I have. You might put a
taper into the end of one of them so
it's more flexible near one end. And the
the idea is that there's different lines
on the boat that are going to require a
different stiffness of batton to give
you a good accurate result.
And to that end, we also have what's
called a bundle batten. So that's just a
bunch of rippings that are thin. This is
just a little more than a sixeenth of an
inch thick, these pieces. And then it's
fastened together with a couple rivets
at one end so that we can create really
fair curves. If you try and do that with
one little whippy piece of wood, it's so
prone to trending to whatever it wants
to do that is not necessarily relative
to the lines you want to lay out that
it's not very uh useful. So, a bundle
batten fares out all the vagarities of
each piece of material in that bundle
batten and gives you nice fair curves.
And I'll have these in different lengths
and in different thicknesses of of
veneer. Here's one for instance that's a
little bit thicker than this one, but
it's a bit wider. And the layers are
thicker still. These are about I don't
know 1 and a half millimeters or
something like that. So you get very
different results between these two. So
I'll use this for doing the tighter
curves and this one when the curves are
larger and more gentle.
And to that end I also use a shift sweep
for drawing curves. Of course the shift
sweep has got fixed curves on it. So you
got to play around with its placement
and do it in short sections to get up
the shape that you want. But this is
really handy for trying to lay out a
stem, for instance, or at least getting
initial lines drawn in to see if you
like the shape. And then I'll refine
them with a bundle batten. And then we
also need tick sticks, which is just a
little thin ripping of wood. It should
be light in color, nice and smooth. And
we're going to be marking uh dimensions
on this, like taking taking markings
directly off the lofting to transfer
them from view to view. And so you'll be
cleaning these up as you go, erasing the
lines off of them or even taking a block
plane and cleaning the lines off. So you
want this to be relatively thin so that
it lays down close to the surface and
you don't get any errors due to the
thickness of the batton.
And then of course we need a scale for
copying dimensions down off of our table
of offsets. And so a good accurate scale
that you use throughout the whole
drawing is is best especially if it can
reach across the whole breadth of your
lofting board. And a raptor square is
handy, but uh you just need to make sure
that it is accurate and square. We we
use this for sort of transferring points
from uh one position to another square
to the reference line or the baseline.
Um but if if you use the dimensions on
it, just make sure it coordinates with
whatever your scale is because they can
sometimes be different and it's really
important that you keep consistent. And
then the last thing we need, of course,
are some nice finishing nails. The
longer and thinner the better. These are
I don't know what gauge these are, but
these are about 1 and 3/4 in long. I
like them long because that way I don't
smack my fingers as easily. And but you
want them as lean as possible such that
we create smaller holes in the lofting
board because sometimes we're just
trying to fudge holes the position the
nails a little tiny bit. And the smaller
the hole you make, the easier it is to
do that. Then lastly, of course, pencils
and HB is good for most of the lines,
but I find that on a board that's been
painted like this, it's very abrasive.
So, you wear down that pencil pretty
quickly to uh it starts getting blunter
and bluntter in short order. And so,
having say an H or two H for some of
those longer lines is helpful. And I'll
use the softer HB for when I'm doing
like the uh the body shapes that are
going to be getting tweaked an awful
lot. something that's easier to erase.
And of course, you want a nice light
claw hammer. You don't need anything
hefty. And the lighter the better. So,
just a little light like 8 oz hammer
burner is all you really need.
So, those are the basic tools of
lofting. Lofting is a uh is an
interesting process. You just have to
sit down and try it a bunch of times
before it's you're going to figure out
how to do it. There aren't that many
books on lofting out there. There's a
few, but I'll show you the ones that
I've referred to in the past. I don't
have them all. This one by uh Alan Vitus
is uh is a purely a lofting book. It's
got some okay information in it, but
it's not one that I've really used a lot
of. It's certainly uh a reasonable
primer, but I think it leaves a few
elements lacking.
I find Howard Chappelle's Yacht
Designing and Planning to be one of the
best ones for explaining the importance
of some of the lines. Now, this
particular book is very wordy rather
than illustrating. There's not a lot of
drawings in there, but I did find it a
useful book to read. It's not the kind
of thing you would start with, though.
Once you've learned the basics of
lofting, then reading something like
this is more uh applicable.
Greg Rcel's Building Small Boats. This
one probably does the best job of
walking you through the lofting process
visually in a way that you can relate to
at the lofting board.
Case in point, he's using illustrations
that show you how you're springing
battens to the specific lines.
And I think it does a pretty good job of
conveying a lot of the information that
you need to. So, if you needed a
one-stop shopping for lofting
instructions, this is probably your best
bet. Greg's follow-up book, The Boat
Builder Apprentice, is also pretty good.
It's got some different information
about lofting, a little less uh
illustrated as the first one, but uh
what's nice about this one is it covers
a bunch of different types of lofting.
So lofting flat bottom boats as opposed
to lofting something like a swamp scot
dury hall where you're lofting to the
plank lines as opposed to referencing a
grid specifically like you are with the
pure round bottom boat. So not exactly a
standalone book but it's a good primer
and it's a good follow-up to the
building with small boats book. Now I
want to give a plug to the Gujon
brothers on boat construction. This book
has got one of the better chapters on
lofting, at least relates to the kind of
lofting that I do.
It describes the table of offsets, for
instance. It explains the different
lines that we're creating.
And while it's not quite as illustrated
in a step-by-step manner as Griggs, it
does have a bunch of different details
that aren't illustrated very well in
other books like laying off diagonals
for instance, uh developing flat
transoms, developing curved rake
transoms, and of course, this is the
subject that we are dealing with here in
this video, which is talking about the
bevel board and figuring out what the
plank bevels are from mold to mold.
Okay, I thought I would just do a little
uh talk here about one particular aspect
of the lofting process
that I think is probably one of the most
confusing of the lot and that has to do
with doing mold reductions. In the
lofting process, we typically loft to
the outside of the skin of the boat. Um,
you can loft to the inside. There's
nothing wrong with doing that. I
personally find elements of that to be a
little bit confusing. So I usually go to
the outside and then reduce my molds. So
a mold reduction is a process of
reducing the size of your molds by the
thickness of the planking. And in the
midship where the planking is at right
angles to the molds, that is very simple
to do. You just take the plank
thickness, you chop that much away from
the mold, and you're done. But as you
get towards the ends of the boat and
especially the bow, the attitude of the
mold to the planking becomes more and
more acute. And if you have a very bluff
bowed boat, it becomes quite acute. And
so to reduce the mold effectively, we
need to understand what the thickness of
the planking is relative to the angle or
attitude it has to the mole. that
dimension is is skewed slightly just
because of the the orientation of these
two parts and that changes. And so the
way we do that is by making something
called a bevel board. And a bevel board
allows you to look at what the thickness
of any particular part is relative to
any particular angle that it is engaged
with, if that makes any sense. So, this
is a this is a bevel board, which is
something we would use just for finding
bevels that we've taken off of things.
We take a bevel gauge,
find an angle off of some part that we
need, and then we can take it to the
bevel board. We lay it alongside the
bevel board, you be an acute bevel or an
obtuse bevel, and uh figure out exactly
what that bevel is numerically.
And so this is basically divided up from
0 degrees up to 45°.
And it just allows me to quickly find
that bevel if I need to use a numeric
bevel for anything. Now, we need to
figure out what the angle of the
planking is to the molds at any given
point. And because that angle changes
over the breadth of the mold because of
the shape of the boat, it's not
consistent from the shear down to the
keel. That that angle changes. And so we
can figure that out using the bevel
board. So what I'm doing here is I'm
going to be creating a a bevel board for
doing mold reductions. And we do that on
a piece of myar. Now this particular
bevel board I have here, this is what we
call a master bevel board right here,
which is basically a big protractor that
I created graphically. We use it to do
exactly what I'm doing here. The first
thing we need to do is we need to know
what our station spacing is because
that's going to tell us what the
accurate bevels are. So my stations are
spaced at 24 in. So if I come 24 in out,
I lay a piece of miler on here and this
is the line along which I'm going to
create these bevels. This was
essentially done the same way. I don't
remember what spacing this one was done
at. Maybe 18 in. I don't remember. So,
I've drawn a line along my twoft mark
out from the the center point of this
this radiating fan here. Put a finishing
nail in here. And then I simply grab
some markers
and I'll just start copying these lines,
tracing them down. And I don't need very
much of it. Just like, you know, a
couple inches of line here. So, I just
start by hitting the fivederee
increments in red. This just makes it
faster to to read when I go to use it.
And there's a point at which I know I'm
not going to go much further than 45° or
whatever I've got here. So, I could I've
got the scale that'll go up past that,
but I don't really bother doing that.
Then, I'll follow up by using a black
marker to trace out all the lines in
between the five° increments.
Of
course, if you're building boats
and you're consistently using say a 24
inch mold spacing, you could get away
with just doing this once. I've done
this many times because
whatever I do with these bevel boards I
create, I misplace them or they get
rolled up with whatever plans they
related to and
I can't remember where I might have
stashed them. So, I find myself doing
this over and over again. Fact of the
matter is, it's faster for me to make a
new one than it is for me to hunt around
for the one that I've already made.
It would be smart if I did one of these
on say piece of acrylic. Maybe I should
do that one day and scratch the lines in
so that I've got a clear bevel board
that I can use for this purpose.
So, this ruler is pivoting around this
finishing nail I've put down here. It's
acting like a a forkrum.
Keeping it the faster it'll do.
And now I need to mark off my planking
thickness which is going to be half
inch. So just use my ruler here.
I'm going to mark off/ inch top and
bottom.
connect the dots.
So this green line represents my
planking thickness.
Now there's some cases in which you
to reduce molds by thicker amount. With
this small boats, it's not very much. I
could pretty much get away with reducing
all the molds by the same amount and
it'll it'll fudge itself out. But as you
get into bigger and bigger boats and the
thickness of your planking becomes
greater, these dimensions make a whole
lot more difference.
So there we go. I'm going to mark this
as a 24 in bevel board.
And I'll just trim this off with a
knife. We don't need it to be very wide.
Two or three inches is plenty.
Okay. Okay. Now, the way we use the
bevel board, we would lay this on a
station perpendicular to this face of
the station,
and we would measure across to the next
one.
And that tells you what the angle
between these two stations is. So, in
this case, it's 5 10 15 16 1/2° between
station one and station two. We want to
know what the average is. So, say we
take station two as an example. We come
across here at this point between 2 and
3 is 5 10 15 20.5°
20.5
and the from the same point the opposite
way
to station one is 5 10 15 16 we'll call
it 17°
and then we take the average of that
which is 18.75.
So we'll call it 19° is the angle is
between this station and these two. So
the the average angle between those two.
And so we can use that along the whole
length of this mold at various points in
order to determine what the angles are
between those points. And then if you
had a band saw that was set to swing
bevels, you could you could drive the
bandsaw through the mold changing those
bevels as we go. Now, we don't
necessarily need to do that. We can make
square molds. But where we would use
that is to reduce the mold thickness by
the right amount. We would come down
here and find where 19 is. 5 10
15 20. So there's 19 right there.
And we can square
square this these lines across from that
point
at the 19 point at the 19° point. This
distance between our plank line and our
and our reference line. This amount
right here
is how wide that planking is relative to
the edge of the mold. So even though the
planking is only half inch thick, when
you skew it, it's just a little bit
thicker.
That's the whole point of this is to
figure out what those relative diff
differences are. Now, because this is
halfinch planking, there's really not a
lot of reason to try and squeeze things
down. What I'll probably do is just take
one or two points on these molds and see
what those are. And I might just uh for
the ones that are most extreme, shave
them down just a little tiny bit.
and make them a little uh
make them a little smaller across the
whole width. So we'll say from here to
here 5 10
square that off more.
5 10 15
16 17 18 degrees. So I would use the 18
degree mark and I would say
this one we reduce it down my ruler. see
what that measures out to.
That's like not even it's it's like
barely 9/16. So, it's it's not really
worth doing too much. And this is
probably one of the most extreme ones
right there uh right near the bow. So,
for this particular boat, this
particular style of construction,
skew, changing the mold reductions by
any amount more than the planking
thickness is not really worth the effort
too much. It's probably easier to just
make it the planking thickness than when
I go to fair off the molds to make sure
they're all nice and clean. Just be a
little bit more aggressive on the uh
molds at the bow here. Just shaving that
corner down a little bit. It's going to
soften the corner which is easier on the
planking and it's going to reduce the
mold by the amount that I need to get it
more accurately laying down on the
lines. So, from a practical perspective,
it doesn't make a lot of sense to do
this bevel board. This is an important
element of the lofting process and the
mold production process that if you are
doing a bigger boat, you really need to
think about this. So, I've only ever
found two good books on this subject and
that is the Gujon brothers on wooden
boat construction. And this page of
course covers the thing we're talking
about which has to do with mold
reductions using the bevel board and how
to find the bevels from mold to mold.
So, this is exactly describing what I've
been doing right here. And then the last
one I wanted to talk about is this one,
How to Build Wooden Boats by Edwin Monk.
Now, this doesn't have any information
on lofting per se, but it's got a great
illustration on one page that has to do
with figuring out bevels. In particular,
it has this one page that I find really
useful. I mean, this is pretty confusing
to the casual observer, but it does show
you quite a bit about how to find
various elements from one view to
another. But the bit that I find really
interesting is this little illustration
right here. You can see how this is
using a raptor square combined with just
a stick and a bevel square in order to
figure out what your angles are between
molds on a lofting. Here, I'm
demonstrating that right here just using
a raptor square and a bevel. So, if we
could zoom in on our drawing, you can
see I've set the raptor square off on
one station mold and then I'm projecting
this stick over to the next one. The 24
in here is our station spacing. And
there's our bevel between those two. And
if I take the bevel square
and lay it off against the little bevel
board that we created, we have 5 10 15
what appears to be roughly 20°.
If I take the same bevel board and I lay
it across here, I get 5 10 15 20° at
this spot. So you can see how these
produce the exact same results. I'm not
sure how well that illustrates it, but
that's exactly the whole premise right
here. That's what this is doing for you.
This is replacing this whole physical
setup. Now, you could make yourself a
little rig that does this. But you saw
how quick it was for me to make this
little bevel board here. It's like a
5minute operation once you have a master
bevel board made. And so, this has the
advantage of showing me what my plank
widths are at any given angle. Now, if
you needed to do that physically without
the use of this bevel board, well, the
simple method to do that is you take
something that represents your planking
stock, like my ruler here for instance,
which is/ inch. If I lay that bevel
square across that ruler, I can see what
the relative thickness is of my planking
at that 20° angle, which is, you know, a
little bit more than a half inch. That
doesn't make much difference on a half
inch rule, but as you get bigger and
bigger, those differences do start to
add up as you get into larger
dimensions. Now, in this particular
case, with this particular boat, I don't
need to get fussy. I can just reduce all
these molds by/ in. It'll be just fine.
But I really wanted to convey this
concept to you because I think it's
really important that you're aware that
it exists and that there's a simple
methodology for finding out this
information, not using anything
particularly fancy and not having to
crunch any numbers with a calculator.
So I thought I might talk about one
other important aspect of lofting and
that is developing sections through the
stem. And the reason we need to do this
is because this stem needs to get shaped
prior to setting it up on the mold. And
we don't need to get it to its absolute
finished shape, but we need to get it
pretty close in order to have it accept
the planking. And so trying to do that
as a rough cut stem that's square in
section on the mold is quite a bit of
effort compared to doing it at the
workbench ahead of time.
And we also want to figure out what the
shape of that stem is through those
cross-sections uh just to make sure
we're building a stem that's thick
enough and such. So [clears throat] I
thought I would show you uh an example
of it here and just sort of try and
convey a particular principle. I've got
my stem construction here which involves
uh the cutwater. This red line is my
rabbit line. This green line is the
inside face of my stem. And so I'm
drawing a line square to the rabbit
through the stem here. So just a square
line through there. So I'm just going to
draw a reference line that we're going
to create the cross-section from. So
we're just going to use half of the stem
because that's all we really need for
this example. At my rabbit line, I know
the half width of my stem is 1 in wide.
And at the cutwater, the half width of
my stem is/ inch wide.
And so if I connect those dots, this
represents what my cut water looks like
in cross-section. This basically this
triangle in here. Triangle with the the
nose cut off. So I'm going to grab a
square here. And I'm just going to run
that square right up to my rabbit line.
Just square that off. That's the actual
face of the uh of the stem at the
rabbit. Similarly, down here at the cut
water, I would square that off, not
drawing to the curved line that we have
shown because we're just this this one
line here as a reference. We're taking
this we're creating a uh taking
something that's like this a cut through
the stem and we're laying it down flat.
Or if you look at this triangle more
accurately, here's the cut
and this is what it looks like flat. So
that's what we're trying to create. Now
we have the inside face of the stem.
which I know I've decided is going to be
1 and 3/4 inch wide is the half width.
So 3 and 12 in wide is my full width. So
I'm going to draw a line square to that.
Measure that off.
1 3/4 is there.
Now, I could connect these dots and that
would show what my stem would look like
in cross-section roughly beveled off,
but that might might not be accurate to
what my planking represents. So, this is
the important part, figuring out what
the planking does. So, the way we figure
that out is we need to find other
references on our lofting that will tell
us how wide the boat is at any given
point.
So, I know my planking touches at the
rabbit right here,
but I need to know how it interacts with
the stem. So, I need to know what the
angle of the of the planking is relative
to this cross-section. There's different
places I can pull off that information.
If I follow this line that I've drawn, I
can look at what other elements it
crosses. And I can see up here, it
crosses a water line that's cut through
the boat, and it's crossing a buttock
line. and it happens to be crossing that
at the exact same point. And so if I go
to my half breadth view, which I
understand from your perspective as the
viewer, you can't make any sense of the
lines I have here. But just to make a
point here, this orange line drawn here
is the buck line in my half breadth
view. This blue line represents water
line number two in my half breadth view.
And that's what both of these are. This
is buckle number one and water line
number two. And this is where they
cross. If I come down here,
I can see this is there's a point at
which they cross right here. And if I
take this dimension, if I use the uh
station line as a reference and I pick
up that width and I bring it down here,
we see that indeed those coordinate. So
this is two different points in space in
two different views that are the same
point.
So I can use that information. So if I
take the width of my
water line for instance at that point
which is this width here
and I square off of our reference line
from that point
and then I use that width that I've just
picked up.
Square it off here. That's a point in
space I can that is that is accurate.
Now, interestingly, this same point is 8
in out from my my center line, which is
the the spacing of my buttocks. And if I
look at this number right now, this
amount that I've drawn, it should be 8
in. And sure enough, it's exactly what
it is.
So that is a line I can trust. If I
connect the dots between it and my
rabbit line, this represents what my
planking should actually look like
coming through here. Now, uh I might
want to pull one other dimension
uh from space here to try and give
myself a more accurate result because
this planking's probably got a little
bit of uh it's probably got some hollow
to it given the shape of the boat. So I
could try and find some other
information. We don't have to get 100%
accurate here. We just need to get
something that's workable.
So then I draw that line in. That's my
planking. I can take my uh my stem here
and project that down. And so I can see
the cross-section of my stem here and
where my planking is on the outside. But
then I need the inside. So I reduce it
by my planking thickness which is/ inch.
And then I can see how wide the face of
my stem needs to be when I cut it to uh
to accommodate this this planking in the
finished product. If I took a piece of
tracing paper and laid that on there,
for instance, I'll draw this out so you
can see what I've just done more
clearly.
So that's my center line.
There's my cut water. It's going to be
shaped like this.
There's the outside face of my planking.
There's the inside face of my planking.
My plank
running like this.
And then there's the stem which
on rough
would look like this in cross-section.
But this is the part that we're going to
be actually making use of in the
finished boat right here.
So we get rid of this.
So there's a cross-section of our stem
at that point in the boat. our stem, our
planking, our cutwater.
And all those angles are developed by
finding elements in the lofting that
represent the width of the boat at any
given point. And we do that by trying to
understand the grid upon which
everything is laid and understanding the
relationships between the various
elements in that grid.
Okay, I hope you found that interesting
and at least I hope a little bit
educational. This was never going to be
a full-blown how to loft boats video.
I'd love to cover that. That's the kind
of thing that the only way to sort of
get it on camera. I'd have to loft a
boat using really heavy line work like a
Sharpie or something like [music] that
because the camera just can't pick up on
these pencil lines very easily. And so
it's [music] not practical for me to try
and produce a lofting like that cuz I
don't have any need for one with that
low uh level of accuracy. And you really
kind of need a a camera person to help
capture that on film. So today I just
wanted to sort of convey a few core
concepts to some of the little bits and
pieces of the [music] lofting process.
Now if you're really interested in the
lofting process, I encourage you to just
try it and start with something simple
like a little flat bottom boat where
you're only juggling a couple of lines.
That will get you the very basic
concepts [music]
and then move on to something more
elaborate. If you go back to my Bushi
Dory series, the first couple episodes
of that [music] series, I walk you
through how to loft a dory style hull
step by step. I think you'll get enough
from those videos to [music] sort of get
started. Once you've tried lofting a
couple boats, the comp sets become
clearer and clearer. The one important
thing you need to understand about
lofting is it is not simply a process
[music] of transferring the table of
offsets
line by line onto [music] a drawing and
copying them verbatim. It's a process of
choosing specific lines from a table of
offsets, transferring those coordinates
onto your board, varying the [music]
lines between those,
and then slowly building out the lofting
from those [music] master lines, wherein
as you add more coordinates from your
table of offsets, you're helping to fill
out the shape. But you're always
referring back to your master lines to
zero in on specific elements of each
[music] line in order to fair it out.
When you're done, you've used all the
numbers in your table of offsets [music]
once and once only. And every time you
need to refer to a particular coordinate
[music] for a particular line that's
already been drawn, you have to go to
the drawing. You have to use a tick
stick to pick up that relative dimension
and carry it from one view to the next.
That is the [music] most important
element of it. You cannot keep going
back to the coordinates and keep using
those. You can only use them once
because we're fairing those lines out
which means those coordinates are going
to change a little bit. You use them
once once only and then the line you
create becomes locked in
mostly cuz you might find you have to
come back and fudge [music] things
around. But as you do you fudge one line
you got to go and check how it affects
all the other ones that it relates to.
Okay, that's lofting in a nutshell.
something that I like to call juggling
[music] spaghetti. So, I hope you join
me again for the next PW boat video.
Now, if [music] you enjoy these videos,
you'd like to help support the channel,
please consider joining me over on
Patreon. You can find links in the
corner or down in the description to get
out into the workshop and try and juggle
some of that spaghetti. All right,
folks. [music] We'll see you next time.
