Mechanical Method for Organic Shapes - Shaping mouldings by feel

Nomad Boatbuilding
98 followers
265 Video Views·Nov 16, 2025
My website: https://www.nomadboatbuilding.com
Instagram: https://www.instagram.com/nomadboatbuilding/
It's not about the money but living isn't free...
Here are some ways you can support this channel.
Buy some merch: https://www.nomadboatbuilding.com/shop/
Support these videos with monthly or annual pledges at Patreon: https://www.patreon.com/nomadboatbuilding
Or make a one time donation: https://www.paypal.com/paypalme/nomadboatbuilding
Howdy folks. Mark from Nomad Boat
Building. We've got a very simple little
project in the workshop today. So, I had
a customer come in and he brought me a
spar that needed lengthening. This is
essentially a a rectangle with sort of
big mushy corners uh knocked off of it.
So, you can see that it's it's a bit of
a lumpy job. Got to kind of do it by
feel than by any sort of calculation.
Now, I'll be releasing a separate video
about the process of scarfing a new end
onto this spar. But today, I want to
talk about shaping it because this is so
artisal in shape that is so far from
geometrically consistent that we're
going to have to tackle the whole
shaping by hand. And I think there's a
useful technique that I use that I'd
like to share with you. Our first job is
to take the portion that I've added on,
which I've made slightly oversized, and
reduce it down to a dimension that is
consistent with the rest of the spar.
So, what I'm going to do is I'm just
going to butt that up against the stop.
We'll clamp it down here.
Now, I think I'm just going to go with a
hand plane for cleaning this up. So, I
think a four plane is probably about the
right size for this. It's always a great
idea to wax the bottom of your plane a
little bit. Makes things go much
smoother. Now, I'll know when I'm
getting close if I start licking uh
paint in the middle here.
If you've been following me for a while,
you know I am more likely to turn to
hand tools over power tools most of the
time. And it's not that I don't think
power tools are useful or efficient.
It's just that I do believe that hand
tools, if you use them routinely, are
more efficient and better for your body,
give you a little exercise, and
certainly better for your soul. Starting
to kiss paint here, so I know I'm down
at about the right height.
Couple
more strokes should ought to do it.
Kissing paint there.
Okay. There's rounding that has to
happen. So that's going to affect my
height here a little bit.
So I think I can stop there.
I think the greatest obstacle to
learning how to work with hand tools
isn't the learning to use the tool so
much. It's the acquiring a tool that is
usable. Finding an old plane that can be
put back into service is not hard. But
finding one that has a blade in it in
which the blade can be put back into
service is much more challenging.
Regrinding the cutting edge is no big
deal, but flattening the back can be a
huge deal. If it's been really abused,
you may not be able to flatten that in a
reasonable amount of time. My
recommendation is to go buy a brand new
blade for it. You can get blades made by
Hawk from Lee Valley Tools, and I'm sure
you can find them from other suppliers.
That makes a huge difference. And a new
blade from Hawk will be put into service
within just a few moments compared to
trying to rehabilitate an old one that's
been abused.
Going a little bit against the grain
here. I can feel that.
[Music]
Could be my plane's getting a little bit
dull, too.
The finish looks fine, though.
[Music]
All right. And this spar didn't fe
feature any tapering for some reason, so
we're not going to bother with that.
All right. Now, to do some roundovers.
Um,
just going to check a few router bits
and see if any of those kind of sort of
match this profile. It's a bit like
rounded over on all faces. Like not
round but not just cornered if you want
to know what I mean. We'll see what we
got that'll come close to take some of
the effort away.
It appears there's no good answer. I was
going to start messing around with the
router bits, but as this thing is sort
of very organic in shape, uh I think
maybe we should just I should just show
you a technique I would use for when I
want to like feel out a shape, if that
makes any sense. I do this quite often
where you you've got an existing shape
that needs to get translated into raw
material that you've scarfed to it. And
so, uh you can't always get in there
with machine. So, you need to use hand
tools to do it. So, there's a technique
I use for doing that. and especially
with rounded shapes. So, let me show
you. I'm going to notch this block so
the end of the spar fits into it because
it helps to have something that'll keep
it from sort of sliding around as well.
So, that's going to become useful.
[Music]
[Music]
Doesn't need to be a nice fit. Just a
fit. Does that go the other way, too?
That would be helpful. Yes, that's
helpful.
Unplanned, but appreciated.
Uh, I think we can get with this. We'll
find out.
No, I'll find out the hard way when I
crash my knuckles into it. So, let's not
find out the hard way.
Here's a tip. When you're making
workbenches, give yourself reasonable
overhang. I've only got like two two and
a/4 in here. I think you need like four
a hefty 4 in to be able to put a clamp
onto something and have room for your
knuckles. Mistake I've made too many
times. Okay, now we're just going to
clamp the other end down.
lively. What I tend to do is I will take
the take the shape that I'm on and I
will try and find whatever represents
the most major
bevel relative to the shape. So in this
case, this has got a slight crown to the
top. I'm going to start by just tipping
this over just 3° or something like
that.
And we're going to run that down until I
see it sort of eating into most of the
paint here.
One thing that helps is if you've got
some pencil lines
that show you where you're going if you
don't have the light to tell you that.
Okay, that feels okay. And I'm going to
turn my plane to the other side and do
it.
Same thing.
[Applause]
[Music]
Okay, there's those crowns. So now I've
got sort of a corner here.
Follow that.
Again,
I just keep going until the work I'm
doing starts touching off on the
original part of the spar.
There we go. Now I'm touching it. We do
the same thing on the other side about
45°.
The systematic approach to identifying
major bevels and removing that material
first and then going back and splitting
the difference between one major bevel
and the last one is the secret to this
whole process. This is exactly the same
process I use when shaping spars and
ores and anything round in a linear
form. It's really very efficient. What
I'll do, let's swap it.
[Music]
All right, next contour.
[Applause]
Using a heavy plane for this is really
helpful because there's momentum behind
it.
If I'm fixing like a molding on a boat,
like a rub rail that's in place,
especially if it's a larger boat, this
is exactly how I would approach it by
just following the contours, breaking it
into bevels, defining the major bevels,
just like I was taking something square
and turning it into a spar. You've
perhaps seen some of my videos where I
talk about the 7107 rule that allows you
to divide up the surfaces of a spar into
units of seven units, 10 units, and
seven units. Do that on the sides and
you connect the dots and it basically
forms an octagon when you chop away the
seven unit portions in pairs. It's just
it's a very efficient way to sort of
create any roundish organic shape.
[Applause]
You notice I'm not bothering to check
angles or anything
cuz when I'm done there won't be any
angles. When I'm done,
it's all going to be roundy roundy.
[Applause]
What you can't know on your side of the
screen is that as I'm coming off the
work
or going onto the work, I'm being
careful to apply the pressure
on the plain soul in the places where
the work needs to be taken off so I'm
not diving down onto the existing spar.
Nor am I flying off before I've finished
carving off the the length of wood. I'm
a few strokes away from done on this
bevel.
There we go.
Developing the ability to work
wrong-handed. Super helpful.
Takes time.
Mostly you just got to think about the
fact that it's not your wrong hand. It's
just your other hand that doesn't work
as well as your right hand. Your other
hand, your other right hand. Well, the
first right. You only have one right
hand, but you know what I'm saying.
Okay,
it's looking real close.
Couple strokes off the top. I think
you can see as I'm coming off of here,
I'm slowly we're slowly getting down to
where we're touching paint and therefore
we're flush with the surface.
When we're done, this is just going to
look like a smooth oblong sort of soft
peak here.
Notice the stance.
Calesthetics all day, baby.
Sometimes
sometimes with boat repair,
it's not necessarily about doing the
best work that you can do, but matching
the work that the person you're
repairing has done. And I don't mean
that they, you know, in the ways that
they screwed stuff up, but in the in the
way like this has got sort of a gy
shape. I'm not going to get too fussed
and try and make a perfect tail end of
this because it's just going to look
weird. So, we just kind of match what's
there. That's that's the ethos I'm
talking about here.
[Music]
[Applause]
And I have I have made the mistake of
doing too nice a job when repairing
something and the part that I did looks
really great and then the part it's
attached to looks like ars. That's not a
good repair. A good repair is one that
is as best as you can invisible.
[Music]
[Music]
Planning painted surfaces. It's not
uncommon that your blade kind of skips
over it cuz the paint can be pretty
hard. Paint is really harsh on blades,
by the way. If you got like some found
some bit of old furniture and you think
you're going to shove it through the
planer and uh and get some nice oldie
timey wood out of it, set your first cut
deep so you get right below that paint.
You try and skim it, you're just going
to eat up your blades. There's no
there's no good value in it is what I'm
saying.
Okay. Can't feel that transition. That's
good.
All right. It's a little hard to control
angle with that big plane like that. So,
just grab a block plane. We'll just do a
little doctoring up.
Try and uh
tease out some of the facets.
This will all get a good sanding
treatment of course too. So
Now, before I waste any time sanding an
inch, I don't have to. We're going to
measure the overall length and chop this
thing off.
I need 160 ines right there.
[Music]
[Music]
[Music]
If you ring your work like that, the
breakoff will happen inside of the face
of the cut as opposed to pulling out a
big chip off the side, which is always
adventurous.
Okay,
probably need to knock the end down a
little bit. How's the other end look?
Yeah, very roundy ovary
chisel, maybe. So, we'll just do this.
Clamp that down. Give ourselves like a
margin
probably like that.
Same thing on there.
Just
eyeball that.
Same as before. 45°.
Get rid of the worst bit.
Okay, then we can split the difference.
We get corners to worry about. 45.
Split the difference.
45.
Split the difference.
split the difference on the inside.
If you're liking these videos, you can
support me by giving me a thumbs up,
throwing me a couple of bucks with super
thanks, subscribing to the channel,
turning on notifications, and of course,
you can join me over on Patreon. Find
links in the corner or down in the
description. I'm not worrying about
being too careful on this, but normally
I would be quite precise about about
these bevels. You're trying to do
something that looks very geometric.
This is not really. So, I'm not worrying
about it.
Same here. 45.
I'm just looking for like a general even
thickness, right? Go 45 there,
45 there.
with the difference
top
and face.
Look for any sticky outie bits
and whatever's left will sand out pretty
readily with a coarse bit of sandpaper
to start with.
Got like
40 grit here.
[Music]
See what I mean?
It's that systematic geometric approach
that gets you to your goal quickly and
efficiently without a lot of head
scratching.
[Music]
I guarantee if you just started rolling
over a corner, you'd stop while things
are still very squarish before you'd get
to your finished goal. You just kind of
think you're done. You look back and all
you see is slightly rounded corners
as opposed to something looks like
properly rounded.
Okay, we're not trying to bring it to a
full bonus here. It's a little bit flat
on the end is what the other end shows.
So, we're going to copy that. All right.
Right now with my long board, I'm going
to uh just quickly do a bit of work
licking that down
back into our notch there.
Find a clamp.
A long board this with both 40 and then
80 grit.
I'm going to use this rolling motion
like this. Going over and over and over
like this thing.
Shift down. Do some more.
That side's done.
Do side then on both edges last.
Okay, we're just going to finish it up
with some sandpaper.
[Music]
Just 80 grits fine for this.
Hit it with a little hund just to make
it fancy.
There you go. You can see how this scarf
just feathers out right there. That
looks beautiful. It's a nice tight glue
line.
You get a little bit of a glue line
there. That's expected because it is a
scarf feather edge.
We've feathered back the paint and
everything like that. So, there should
be a pretty smooth transition for the
owner to go ahead and reprime and
repaint this. That's it for today,
folks. I hope you enjoyed that. Now,
please keep your eyes peeled for that
West System video about doing the repair
on this spar. And until then, get out in
the workshop, get your hands dirty, and
don't forget to put those hand tools to
use. See you later, folks.
