In Part 9 of our 1953 General Electric 17T5 television restoration, we’re putting the bench progress to the test to see if this 70-year-old CRT can reliably play vintage broadcast cartoons with working audio.
After checking the picture output, we dig into the sound section distortion, reference our 1951 National Radio Institute study course (with a quick spider interruption), recap the remaining audio circuitry, test replacement vacuum tubes on the B&K 747, and finally hook up the video signal to watch classic Popeye footage on the glowing screen.
If you enjoy vintage electronics, tube radios, and antique TV restorations, make sure to like, subscribe, and share your thoughts in the comments!
Chapters & Timestamps 0:00 - Initial Video Check & Audio Distortion 3:46 - Reading the 1951 NRI TV Course (Spider Encounter) 11:25 - Analyzing the GE 17T5 Audio Schematic 21:00 - Recapping the Audio Section 29:45 - Testing 6AU6 & 25L6 Tubes on the B&K 747 35:58 - Bench Power-Up & White Noise Test 36:20 - Popeye Cartoon Test on the 1953 CRT 40:02 - Final Thoughts & Upcoming Projects
Check out our Patreon page, for all of our channels. Contains outakes, concise arcade repair tips, bloopers, repair FAILS, Audio youtube wouldn't allow us to upload, and much more!
This video documents the technical restoration of a 1953 General Electric 17T5 television. After improving video clarity, the presenter focuses on repairing the distorted audio section. By studying vintage textbooks, he identifies the chassis as an inter-carrier system and proceeds to replace degraded capacitors, drifted resistors, and faulty vacuum tubes to restore both sound and image focus.
Ladies and gentlemen, welcome back to Amateur Repair Time.
We have been working on this old school General
Electric 17T5 television chassis from 1953.
And I've kind of got it doing its thing.
If you haven't watched the series so far,
we worked all the way through it and figured out a bunch of stuff.
I learned a lot.
And we got up to where we're getting video now.
Got a VCR hooked up to it.
It almost kind of looks like it's better than
the last time that we were messing with it.
We had a little more interference last time.
This looks a lot better.
I don't know how that happened.
But we haven't messed with the audio section yet.
And although it does sound a lot better now,
the amplification doesn't sound like it's all
the way where it should be.
Now part of that is probably just
because we've got this small speaker. This wasn't actually
mounted in that case.
This is about a three and a half inch speaker, I would guess. And it's
supposed to have a five inch speaker.
See the drill on the side of it there? So I would like
to get, you know, there was some interference last time
and there's not now. So I don't know
what happened with that.
I wonder if it's, I wonder if I've got, I don't know why that would
would be. But anyway.
Um, we haven't done the audio section,
so we're going to do that in this video,
and then we may try to align the thing.
I don't know if we'll get to that in this video or not,
but we kind of need to check the alignment.
I'm kind of speechless because the video quality is
so much better.
It had a lot of snow in it before, so that's focus.
This is very passable the way it
is. Like, I don't know that it needs to look much better than that.
Yeah, this is contrast.
If I turn down the contrast.
Yeah, it looks a lot better than it did.
I don't really know how I should have the
contrast set. And I don't know if it should be solid black background,
or if it should be like that.
On the screen, on the camera, it looks blue. It's not blue here
in person. To my naked eye, it's black and white.
There's no blue haze to it,
so I don't know why the camera does that.
I guess there's some kind of filtering.
tech in the lens that just makes it do that,
but to my naked eye, it's black and white. It looks
freaking awesome, really. I mean, just a really cool vintage look.
Obviously, we've got some
problems with geometry and things like that,
but most of that's going to be adjustments.
Okay, so let's read about the sound section a little bit,
and then we'll work through it.
All
Now that should be the last few caps that we've got
to replace in the thing and then we can we'll
see if that ups our amplification
or if we if we're going to need some kind of alignment.
right.
So this is the book that we have been using.
Basically, I've been reading through this as we go,
just trying to see if I absorb
by osmosis any information about how television circuits work.
This is Practical Radio Television.
It's a book by the National Radio Institute that came out in 1951.
It's a study at home course.
And I'm sure it predated that, actually,
but this is the version that I have.
And the original gentleman that bought it,
apparently, was W.E. Raines, Jr.
We think that he was from Hartsville, South Carolina.
So it was just this course with all kinds of different,
you know, subjects.
And you could order just tons of them.
These are all over eBay.
You see how it has a number like 49RH4,
and then the next one here would be 50RH2.
Did y'all see that spider?
There is a spider right there.
What in the heck? Where did that guy come from?
That's one of the things about having all this
vintage stuff. You run across creepy crawlies.
Look at that spider. I don't really know what
kind of spider that is, but he's fast.
Look at that little sucker.
What is he, folks? That's
not a good looking spider to me. I don't know.
I don't think that's a brown recluse. I don't
know what that is. I'm going to kill that spider.
And if I live through this ordeal,
We'll find the audio section
of this National Radio Institute study at home course.
I'm letting it get some time on it now.
All right, so I found it.
And the spider's gone.
The sound channel.
Let's see if we learn anything.
In general, the sound channel
of a TV receiver resembles very closely the IF detector and
audio portions of an FM sound receiver.
I haven't worked on too many FM radios.
I've worked on a lot of AM radios,
and I've got a whole bunch of, you know, little collectible,
Not collectible, but little...
Desk radios, I guess you would call those.
And, you know, I've worked on some of these consoles.
Most of them are AM, so the FM circuit is a little bit different.
There are some differences between them,
however, which we shall now discuss.
First, let's make sure you understand the difference between
the so-called standard or conventional
and the inter-carrier or inter-modulation sound systems.
Well, I'm glad they're going to tell me
because I, in fact, do not know.
I think I kind of know.
They're saying that it's going to be on the frequency.
It's basically going to be modulated
into the frequency that's carrying the TV signal, too.
There's going to be a band for the video and a band for the audio.
I think that's what they're going to say.
Standard receivers.
Figure 22A shows in block diagram form the arrangement
of stages in the standard TV receiver.
In this set, the mixer-first detector,
or converter, produces two IF frequencies,
a video IF carrier that is amplitude modulated.
by the video signal and sync pulses
and an audio IF carrier that is frequency modulated by the
sound signal the transmitter radiates two separate carriers
with these modulations and the local
oscillator beats with both to produce the two new
IF carriers the sound IF carrier are they saying
this is typical standard TV receiver
the sound IF carrier is 4.5 MC okay below
the video IF carrier
When the oscillator is above the frequency of the incoming signal,
as it is in most receivers.
If, for example, the video IF carrier is 25.75 megacycles,
the sound carrier will be 21.25
megacycles. In most modern TV receivers,
the video carrier is somewhere between 25 and 46
megacycles, and the sound carrier
is therefore somewhere between 21 megacycles and 42 megacycles.
Since the sound
and video carriers are two entirely separate signals, the two can be
separated by tuned circuits.
In some sets, the sound takeoff point is right at the output of
the converter. However, if greater gain is desired,
and isn't it always, the sound may be
taken out after the first or second video IF amplifier,
in which case these stages must have
a sufficiently broad response to handle both carriers.
Interesting. So this is how it's
It's normally set up.
It says.
Block diagram of a standard TV receiver,
A, and of an inter-carrier set, B.
So it's showing us the input tuner, the signal is split,
or I guess actually the same signal goes to the first sound IF,
second sound limiter, or third sound IF,
FM detector, and then the audio IF.
And then at the same time, the video is going to the first video IF,
the second video IF, the third video IF,
and the fourth video IF, and then off to the video detector.
And it looks like that they.
This signal is put back in at times.
Look at this.
Now I've got a freaking ant.
Or is that the spider with a couple legs?
That's the spider with only a couple legs knocked off
because I didn't get him completely dead.
Oh man, he's coming at me.
I gotta go.
All right, I think I was able to get rid of the spider,
but he may show back up.
Okay, so it looks like that they send that signal back in
after the first and second video IF for some reason as well.
Okay, so moving along.
After the sound IF is removed
from the video IF path,
It is applied to a regular IF amplifier having
a pass band of about 300 kilocycles.
Usually there are two sound IF amplifier stages followed by one
or two limiter stages,
the latter of which feeds into a discriminator.
In some sets, a ratio detector is used instead of a discriminator.
In which case the limiter stages may be converted
into regular sound IF amplifiers or may be missing
altogether. In general however,
there will be at least three stages in the sound IF portion
of the set including the limiter if one is used.
From the discriminator, the sound signal passes
through a normal two-stage audio amplifier before being applied
to the loudspeaker.
The power output stage may be push-pull in the larger sets.
Let's see what ours looks like.
Okay, so it's saying that it can be taken out after their first
or second IF amplifier.
I think that's what the dotted lines are.
So they're saying that this signal,
instead of coming from here, may come from here or here.
Because it appears that's something like what we've got.
And by the way, on our sound on the TV right now,
it's sounding distorted while I'm just letting it sit here and play.
So the volume I've got all the way up, it's dropped precipitously.
Honestly.
And it's kind of distorted now.
So there's definitely something going on with the audio section.
Here is how they've done ours.
So the signal is coming in here
and running into the video IFM.
And then it's running through its thing.
And after it goes through the third video IFM,
now this is the section, and this is the detector diode.
Is that what it's called?
Yeah.
After it goes through that section right here,
the audio splits off so the audio comes up here
and heads back over here and feeds into the first
sound IF amp it then goes to a limiter and then
goes to a ratio detector and then goes to an AF
amp and an audio output and it does
not look like it's push pull to me so um yeah ours comes out
after the third IF amp
and then that I want to look at that part too because I'm trying to
I can understand what they're saying.
We have a converter up here and we have an oscillator down here.
And if you look,
the signal is actually from both.
So you've got one here
and the oscillator is connecting
at the same spot. So both the converter
and the oscillator are combining into that IF signal.
And I think that's what it just said,
didn't it? Let's look at that again.
The mixer first detector or converter produces two IF frequencies,
a video IF carrier that is amplitude modulated
by the video signal and sync pulses
and an audio IF carrier that is frequency
modulated by the sound signal.
So that's the transmitter radiates two separate carriers
with these modulations
and the local oscillator beats with both
to produce the two new IF carriers.
All right. So that's a little that's that's not what I was thinking.
OK, so intercarrier system.
At first glance, the only difference between
the intercarrier system shown in figure 22B
and the standard shown in figure 22A appears
to be that the sound takeoff is at the output
of the video amplifier in the former.
Actually, in the intercarrier system,
there is rarely more than one stage in the sound
IF portion, which is why the circuit is popular
with the manufacturer of smaller receivers.
In the intercarrier system,
the two carriers pass through the video IF amplifier together.
When both are applied to the video detector.
A beat of 4.5 megacycles occurs between the two carriers.
So that's what's going on with ours.
Because ours is coming off after the detector.
And that's why they're saying
that there's only one stage of the audio amp.
This difference frequency is frequency modulated by the sound signal
and somewhat amplitude modulated by portions of the video signal.
Now, I don't understand most of this, folks.
I'm just trying to, like I said, drop a little water in my melon.
If I catch some of it, that's all I'm looking to do.
To fully understand this stuff takes either lots of studying
and really putting your mind into it
or years and years and years of just absorbing it.
So I'm more of the years and years
and years of absorbing it type of guy.
I got a hundred other things that I'm doing at the same time.
So I'm content to read this, see if I remember a few things,
and then next time I'll catch a few more things.
And that's kind of how I like to learn.
This new 4.5-megacycle carrier then passes through one
or more stages of the video amplifier.
At some point, it is trapped out of the video path
and applied to the 4.5-megacycle sound IF section.
The sound IF is tuned to 4.5-megacycles regardless of the video
and sound IF carrier frequencies.
This 4.5-megacycle signal, with its complex modulation,
is amplified by the sound IF
and then fed to either a discriminator or a ratio detector.
Here, any amplitude modulation is wiped out.
With the result that only
the frequency modulation produces an audio signal.
Of course, if any stage in the chain handling
the 4.5 megacycle signal is overloaded by this
or any other signal, cross modulation products will
be set up with the result that some of the
video modulation may cause a hum from the loudspeaker.
The audio amplifier used with
the intercarrier system is just like that found
in the standard system. To sum up, here we go,
to sum up, the major differences between the standard receiver
and the intercarrier type are
In the standard receiver,
the sound takeoff point is in the video IF amplifier either
immediately following the converter or after the first
or second video IF amplifier stage.
In the inter-carrier system,
the sound takeoff is in the video amplifier. So we
absolutely have an inter-carrier system.
In the standard receiver, the sound IF
amplifier is tuned to a frequency 4.5 megacycles below
that of the video IF amplifier. There are
usually two amplifying stages followed by a limiter
or two in the sound IF section.
In the intercarrier system, the sound IF amplifier is tuned
to 4.5 megacycles and rarely has more than one stage.
Now, when they say more than one stage, they still show
that there is a sound IF, an FM detector, and then an audio amp.
So if you go back to ours,
we've got sound IF, the limiter,
the ratio detector,
and then the amp, right?
And then you get, actually, you've got an audio output tube, too.
And I've said it in the previous videos.
This is from 1953 and you know at that time a lot
of stuff was coming along so if it's slightly
more advanced than they say it's
because this book was from 51 and the design is from 53.
Since the video section of a set using
the inter-carrier system handles the sound signal also,
it must have a greater bandwidth than
is necessary in a standard set. There we go.
Whether the standard or the inter-carrier system is used,
the sound signal must be kept out of the picture as much as possible.
In the standard set, the video IF stages, following the point
of sound takeoff, always have one or two sound IF traps.
These traps, which are tuned to the sound IF frequency,
are intended to attenuate the sound signal
so that very little of it will reach the video detector.
If even a small portion does reach the video detector,
the 4.5-megacycle beat that is a
characteristic of the inter-carrier system will be produced,
and in addition, because of slope
detection in the video detector,
the sound modulation will be converted into an amplitude
signal. Both these signals can appear in the picture.
The 4.5-megacycle beat will produce
a very fine-grained dot pattern,
and the audio signal will produce bars across the picture.
Some sets have a 4.5-megacycle trap
in the video amplifier to remove the 4.5-megacycle grain pattern
In spite of the sound IF traps, the sound signal may reach the detector
if the set is not properly tuned to the station
or the circuits are out of alignment.
Yeah, this is why sound bars show up
when the fine tuning control is improperly set.
In the inter-carrier system, 4.5-megacycle grain
traps are usually found at or following
the point of the sound IF takeoff.
Some of the small seven inch sets using
the intercarrier system do not use grain traps
since the fine grain pattern produced
by the 4.5 mega cycle beat is not too apparent at the normal
viewing distance for a seven inch tube.
So they're telling you right here that if I was having a
little bit of interference in the video it might be the sound
although they're saying that um well
I don't know if the trap that they're talking about
is made with capacitors and if I haven't
replaced those capacitors yet that could be the deal.
So we'll look through it.
Producing the inter-carrier beat.
I don't know if we need to worry about all of that.
Okay, you know, I kind of got a little
overview of it just reading that.
Discriminator, the ratio
detector, inter-carrier sound IF system.
That's what we've got, obviously. And then we're up to
automatic gain control. All right,
we've already been through all of that. So if you didn't see
the previous videos, I went through and I did all the caps,
checked all the resistors
section by section, but we just simply haven't done
the audio yet. So that's next.
Alright, so this section around here is all of the audio,
and I'm going through, and all of the resistors,
or it seems most of the resistors are still pretty close,
but there's actually four paper caps that I haven't done yet,
and I think one of them is an electrolytic, it might be, yeah,
it's this one, well, I don't know if electrolytic is the word,
it's a polarized cap, so there's this one, two, so there's at least
four capacitors there that I haven't changed yet in the audio section.
I was able to move this transformer out of the way.
It was bolted in. Get back in there. And
there was another cap
hidden behind there.
So it is here just after the AF amp.
And it is
greasy. That thing is like in horrible shape.
It's all falling apart. Or the wax on the outside of
it is. I don't know about the actual cap itself,
but it's like really oily. So you would think
maybe that came from inside the cap. I don't know.
It's good we're getting it replaced.
Okay, so I've been working through it, and I've got most of them.
There's still a couple that I'm searching for, actually.
Actually, um...
One of them appears to be inside of this couplet.
I prefer to call it a couplet.
But it looks like this cap right here
is inside of that, 0.01.
So we're going to leave that, but it wouldn't be a paper one anyway.
I mean, it ought to be a little better quality inside of there.
So, um, we'll see how it goes.
However, while I was messing around, I found what I thought might
be a cap that was like all screwed up,
rusted and had a green mold on it, corrosion on it.
So I started screwing around with it and it popped off.
And then after I felt it, I thought,
well, wait, that might be a resistor.
So I've been messing around. It took me about
45 minutes to figure out what it was. Now I knew where it went.
But you kind of have to figure out
on the schematic what you're looking at.
Where does each tie point go, et cetera, et cetera.
So the best I can tell on the couplet, pin one is right here.
Pin two is right here.
That resistor is a little high there.
But the thing was working, so I don't know.
I mean, we may end up with some audio problems.
I don't know.
And then pin three is right here.
That cap appears to be part of the couplet.
Pin four is right here.
Again, this is a little high.
It's 25% or so.
Well, 21 percent, something like that.
This is pin four, okay, and that this is this right here. It's
a resistor that is supposed to be 1100 ohm, two ohm,
1100 ohm, two watt resistor. It attaches to
the focus coil.
I had focus, but I didn't think it was the greatest, right?
So that may help us out.
Because this thing had drifted. This is like crazy.
Instead of 1100, it was more like 9K,
something like that. It was way high.
So I've got this one. About a year, year and a half ago,
somebody sent me just cases of old resistors
that they saved somewhere, one of the viewers.
And I have kept those and I carefully sorted them.
And so I've got a whole
ton of them. And I went through
and I sorted every freaking one of them.
basically by size so what i did
was these two cases here it started out as one but i had so
many i made a second one these are 1k and above
so you look through this is an 1100 and judging
by the size it's about a two watt
so we'll put that on there to replace this one that i broke
30 minutes ago and uh we'll go on from there all
right folks i got them all replaced um there was
There was a real tricky one right here.
It was underneath.
It goes from here to the back.
Plane and that back plane is ground.
I went through, I tested the resistors as I went.
I've been trying to do that the whole time.
There is one discrepancy on the volume control. It says
that there is a lead coming off of it here.
See that X though? I don't know what that means.
And it says that it has a resistor
and a capacitor to ground. These don't exist.
They would have been right here on the potentiometer.
If you didn't see the previous
videos, I broke this little piece of bakelite
or whatever that was holding it in place.
So I've got to fix that, replace it.
But there's no cap and resistor here, so I don't know.
I'm going to look back at my earliest video just
to make sure I didn't take that off,
but I don't think I would have.
And on the schematic, there is an X right there.
So I wonder if that means that that's removable in some sets.
Remember, these schematics are for like 12 different sets.
So I wonder if that was on some and it wasn't on others.
That could be the whole thing.
Um, so that was really the only discrepancy.
Everything else is there
and everything's pretty close to what it's supposed to measure
with a couple exceptions that are like 30% out instead
of 20% out, but all in all, it
looks pretty good.
So, um, I think we're ready to test it again and see if we can,
um, see if we can get a
louder volume out of it.
Keep in mind though, that the speaker is too small.
It's supposed to have a five inch speaker
and it's just got some little cheapo one in
it.
So a better speaker may fix the whole thing, but we'll see.
I'm also interested in seeing what that focus resistor being
so far off was doing to it.
So maybe the focus will be much better.
I don't know.
It might just change where
on the focus adjustment it's at the best focus.
Okay, so we never tested the tubes in the audio section.
So the very first tube is the first sound IF amp, and it is a 6AU6.
Simple tube.
Let's see what we got.
Nah, it ain't great. Nah, it could be better.
Let's try the second one which is actually the
same exact tube before I go digging for tubes.
Let's see if it tests similar or better or what.
But this one's borderline.
So this is the second one which is called the limiter.
The limiter is limited. All right,
so let me see if I can go find some 6AU6 tubes.
So I've got tubes stashed all over the place
and I've been looking for about 20 minutes.
And so I went into some cubbies that I have,
or what, caddies that I have, and I found
this one that, that's my handwriting,
so for some reason I put one in this box.
Maybe I ordered one on a previous video or something.
And then I started thinking, you know,
I've got a bunch of unsorted ones, or unboxed ones.
Let me go look in there.
Now where I got these was,
I bought about four lots of...
Hundreds of tubes.
I even bought thousands of tubes off one guy.
And, you know, very inexpensively.
And so I went in and started looking.
And, you know, I've tried to sort them.
And I spent hours and hours and hours
and hours going through and sorting them
and putting them in boxes and things like that
and sorting them into these caddies that I've got.
But I don't have all of them sorted just
because there's so many of them.
And they're all untested, really, so I don't know if they work or not.
I've got to test them.
And so I was looking, and I only found
that one, and, you know, I need two.
And so I was like, well,
I might have to order some on eBay so I have some backups.
And then I thought, well, you know, let me
go look at those ones that are unsorted
because they kind of have a unique look.
You know, they have a one.
It's kind of one of the smallest forms.
And then it has this...
this shield inside of it
so it might be easy to see at a glance. so i went to my big collection
of loose ones and there's some in there that are in bags
and i found this bag. so that's like a
hundred of them that i already sorted. i must have bought them
and they were all in one box and i
just knew that they were all that one. so i've got
a few here that i can test through but i'm gonna
If they don't test good, I'm throwing them in the trash
because I don't plan on keeping a whole
bunch of ones that don't test good.
So I'm just going to start pulling them out, testing them.
If I'm not getting good results, I'm throwing them in the trash.
Like this particular one that
was testing way down here, it's trash. It's gone.
I got plenty of backups. All right. It doesn't
really matter, but I figured, you know,
why not put GE ones in it since I've got a thousand of
them. Good enough for me. So that's our first one.
Okay. Here's another one.
Very nice. Good enough for me. All right.
So we fixed that problem. On to the next one. So next
up is the 6AL5, which is a little tiny
thing, which is the ratio detector.
So it's got two
sides, no shorts,
no gritty emission problems.
Nice and strong.
To go to just around a little
bit. I'll make sure
I got them right.
C, A, B,
and then F here.
Shorts, no gritty
emission
problems.
Okay, so the 6AL5 is still good.
All right, so now we are up to the 6SQ7.
It's a Sylvania,
so it's been replaced at some point.
Shorts, no grid emission
problems, and it's okay.
Let's see what the other side of it looks like.
It's actually a triode,
so this is part two.
That says a short, folks.
Let me make sure I've
got it set up right.
I do not have it set up right.
Should've turned that one off.
Still says shorted, though.
Let me double, triple check,
and then we'll look for some more.
Well, I looked and I looked and I looked and I had one,
uh, six SQ7 GT, which is the glass
version, right? Put it in.
It also had a short, and then I kept looking around and it was because
I had this set wrong. So I turned them,
they were on A on the, on the first, uh, part. And so I
turned them like that. And then instead of going
to B for whatever reason in my head, I was putting
So once I put it on B like it's supposed to be.
no grid emission problems and it tests pretty good you know all right
so on to the third uh side of
the of the triodes to see
that let's see yeah same deal
the shorts no gritty
mission problems i'm not
really happy with it i think i'm going to go ahead
and put this in let me test this one so this is
the third side of this one
the second part of this one and the
first side of this one oh come on now
So it's really no better than the other one.
I thought this one was new old stock, but it had a
lot of dust on the top of it, although it was in the correct box.
I think somebody put it in
something else. So it's really no better than the other one.
So I'm just gonna put the other one
back in. That's the only, this is the only extra one that I've got.
We'll roll with what we had.
And finally, here is the first part of it.
Better than the other one, and I think we'll roll with
that. That other one is probably fine,
but this one tests stronger, so I'm gonna roll with this one.
Okay, and finally, the audio output tube. It's a 25L6.
So, uh, let's see what we got. No shorts.
No gritty mission problems.
Eh, not great.
Let me see if I've got another one.
All right,
so I've got snow.
Looks pretty good with no signal.
And I now have white noise. So, um,
yeah, we might have got somewhere.
I don't think I could do that before. All right,
let me hook up a video to it, and we'll see what happens.
All right, I think we've got it.
So I adjusted the geometry a little bit. It's looking pretty
good. And I think we've got plenty of volume.
I can't turn it up too much for too long because
they'll give me a copyright strike.
A little cheap speaker. Once I get a better speaker on
it, it'll sound
a lot better. Very cool.
Got a little bit of, you
know, it's not as bright as
But isn't that how it always is?
If I over.
You know, if I make the background too bright
and it could just be that this is a bad, uh,
this is a dark concert, you know?
So it could just be that this is a bad,
you're not going to get a great video out of this
on this era of television because it's a live television.
It's a live show with spotlights on the stage and things like that.
So the contrast is a little strange
and I can turn it down like this to where it's pretty
good, but, um, I can certainly watch it like this.
It's not a...
I would be just fine watching something like this.
Let me see if I can find a different tape
or something that'll look a little
different and we'll try that.
I think the little bit of movement
is from them recording it off of a projector, I think.
I think my sync is locked in pretty good.
I think that's an artifact of the,
this is a really old, it's a DVD, but it's a really old
Recording. So it looks pretty good.
I think the brightness is probably up a little too high
though. So like if it showed a black screen,
it would look too bright, but, um, I'm happy with
that. So the, the 12 L six, I didn't have another one.
Um, I've got some in storage though. So I'll
bring one in or not 12 L six, 25 L six.
I'll bring some in and swap that out just to make
sure we're getting every bit of the volume we can.
But, um, I'm pretty happy with how it's
It's turned out so far, I'd be happy to watch it like this.
Um, and the focus, this is,
it focused about as good as it gets, so I can go way off focus.
A lot of this isn't going to show up in this video
because of the camera, but, um, yeah,
so I like it.
I think we're doing pretty good.
Okay, so I still need to fix the volume knob,
um, and the actual on-off switch is screwed
up too.
I've got it just wired on.
Oh, here it comes.
It's the payoff, people.
All right.
Um, and we need to work on the cabinet a little bit.
Clean it all up, put it back together.
Like I said, fix the mount of that. I'm missing a knob.
I haven't been able to find the correct one.
I've got something here. I've got part of it or
something. I think that goes with that or something.
We'll figure it all out.
And if I can't find the knob, that's easy enough to fix.
But, yeah, I'm happy with the progress.
The next week we'll work on, I'll probably do something else.
I've been trying to do, like, one week do the TV,
the next week, because it takes just so long,
the next do a record player,
the next week do the TV, the next week do a radio,
the next week do the TV, the next week do a clock.
I've been trying to stagger it out because.
Um, some viewers, uh, are going to get really bored just watching,
you know, 10 videos in a
row on about a television. So, but I hope you enjoyed it so far.
It's been really fun working
on it. I've bought some other televisions since I got
this one. And you know, if you watch the
very first video, see how that was white instead of black.
Um, if you, uh, if you watched the very
first video, you saw that we went and picked up some,
uh, uh, two tip televisions. So, uh,
I've still got the other one, and I've picked up one, two...
Three or four since then, so I've got a whole bunch of them.
I'm not going to do them back-to-back or anything,
but as I see them, I've been picking them up
if it's a cool vintage 50s television like this.
All right, folks, I hope you enjoyed it.
Leave your comments below, and we will see you on the next video.