PPO3 is supported by Timber King sawmills. For more information on my 1220 CRZ mill
or one of many Foley hydraulic options go to TimberKing.com. It's already 2 30 in the afternoon
and I'm just now getting started outside. It's just one of those days where I get a lot of
running around in the morning and all the running around stuff you just feel like you
I don't feel like I got anything done. So I gotta make some changes and do a few things
and I've already done a bunch of stuff so let's just jump in. Fans are not cutting it anymore.
See all that coloration the blue coloration there that mold and mildew. Every time I cut lumber and
stack it out here I usually run a fan and well I do I run that fan and it runs 24 7 for the first
few days and with that amount of airflow I've never had an issue with mold out here properly
sticker stacked but as you can tell getting some mildew on here. So this isn't working
like it has been in the past primarily because we've gotten a ridiculous amount of rain over
the past month or so. We're normally supposed to be in our drought but we had a drought earlier
this year than normal. Anyway it's hot it's sticky it's humid no longer can I let a bunk
to just sit here and dry underneath the lean-to anymore with a fan. Instead I got to put it out
here where there's I guess better airflow even with the fan this is still I guess better airflow
because I had I don't know if you remember I had the two two bunks stacked right here for the
longest time and those bunks didn't mold they got weathered you know just on the exterior surface
but they didn't mold sitting right here. Well I don't want to have a big eyesore right in front
literally right in front of the garden so I'll still have that eyesore but we're moving it over
here. So my thinking here is we still get the prevailing winds coming through the bunk if I
have two bunks right here for material and that's going to be a benefit and for various different
reasons. Also because this is all gravel right here so no matter if it's raining or not I can
throw the pallet forks on the tractor and load somebody up if they're wanting to get some lumber.
So I think the next stage of the lumber sawmill evolution is to keep the lumber over here. I've
plenty of area over there to put the bunks and it's out of the way and it's not an eyesore and
who cares but at the same time when it rains and gets muddy I got to drive through the mud to get
the to get the material so I don't really like that. This just seems to be the best spot. So
lumber right here going forward. I was moving a bunch of stuff yesterday with the tractor and
tore down Tyler Kaye's very first play fort because she no longer wants it full of nails
and I used the grapple to get all of that stuff right where those burn barrels are right there.
Pile's completely melted completely burned away last night not that burn pile second burn pile
but in the meantime of moving everything over there I think I ran over a nail so I've got a
flat on my front left tire. If it is a nail I'm hoping it is then a quick patch will be fine.
I've got patches in two of the other tires so got to get that done today but also I cleaned up on
the other side over there a little bit so let's go over there. Her play fort was right there and
I got to move that rainwater bin somewhere else until we figure out an actual solution for it.
We're still still kicking that can down the road but now that I have this empty I want to stop
burning over there and I want to keep burning over here where there is actually a burn pile
in the tall grass so I think I need to mow this real quick and get it knocked down so I can get a
better idea of how this is going to be over here. Okay that's one thing to do today probably the
first thing to do because the flail mower is already attached to the BalmaLite. I did some
mowing yesterday or was it yesterday or the day before and it's ready to go so I might as well
knock that out. Another thing that I want to do today is get a dedicated electrical circuit for
the air compressor. This thing pulls um 15 amps at startup I think I forget the I don't know if
it's 15 amps or not but anyway um it pulls enough to where it keeps tripping the breaker even when
that's the only thing on the circuit warning from the breaker panel way down there so we're just
gonna get we're getting too much voltage drop for this distance. So is that rain? It sure is
rain must be a small rain cloud. So I want to get a dedicated circuit for this but much closer to the
electrical panel well right there so the other side of that beam right there on the inside
is the I-beam which means right there is a secondary breaker panel I can tie off of that
come out of the wall right here and put some receptacles right here for the air compressor.
I want to do that another reason why I want to do that is because I'm feeding the wires
uh through the window right there now that we have AC in the shop I don't want to leave that
window open all the time so that's something else to get done. All right back in the shop
uh there's the panel the sub panel and like I said I can come out of that go right through the wall
right there and have some electrical outlets mounted probably one high to put another one of
these cord reels outside and then one down low for the air compressor right there got to get that
done and while I'm up there doing that I don't know if I'll get to it today but I got to run
another circuit down over here and down to this cluster right here this wall I've got one circuit
for 240 volt and I'm using that for the CNC. I need another circuit right there for 120 volt
dedicated to the 120 volt motion controller as well as the spindle um what's it called the pneumatic
changer on the spindle so I've got to get that done as soon as that's done I'll build a cart
for my computer so I no longer use this really expensive computer desk right here to get this
going completely going it already is going uh on the on my woodworking channel I did a five
five part video series of building it but I never showed it actually running well
I've got two layers of spoil board already attached to the machine and flattened still
have to tram the spindle and make it nicer but it's plenty good enough for what we need to do
now I did a uh one pang job uh to just I guess kick all this off so I've already used it to make
something um just have to button up all the other little things a bunch of little tasks to end the
day a bunch of little tasks to start today oh start today so when I was running errands in town
I got a phone call from the tree service company they may have some more wood chips for us that's
always good for us but also more logs tomorrow I think it's tomorrow they're taking down three
oak trees in New Albany the big town next to us um and the biggest of the three trees has a base
that's about 70 inches in diameter all three of them are oaks two of them are red oaks I'm not
which type of red oak but it's definitely a red oak leaf on it and then the biggest one is a if
I'm not mistaken a willow oak which a willow oak is a type of a red oak it's just different leaf
structure anyway 70 inches in diameter at the base on the big one whoa uh I don't know what's going
to happen but um it's it's not really a full circle it's more like a oval shape so the widest
part of that oval is around 70 inches and the narrowest part is probably 40 inches or so so
that gives you two different ways you can put it on a mill not my mill but a mill and depending on
which way it is you can you know cut it up uh so I don't know what the what the goal or what the
deal is with that I'd love to get it but if I can't get it I just can't get it as far as the
trailer capacity and whatnot so that's that's uh gonna happen which means I need to get the tire
on the tractor fixed I need to just shut up and get to work so let's go what an incredible machine
incredible combination you see how tall the grasses are right they're taller than I am
and uh we've got some dips over here some dips over there there's another big hole over there
this one was holding water ish and uh got stuck a little bit but you lift up the implement and
just drive out of it it's just it's just a it's a beast of a mower it really is and you can get
right up next to these stumps to where you don't have to come back and do any weed eating
it's just such a capable machine it's not my machine unfortunately it's just a rental agreement
that I'm able to use this for right now but I'll tell you what when the time comes for me to return
these these bomelite with the bomelite mini skid and attachments huh it's gonna be a sad day around
here because I'm getting so much work done with these I was letting it cool off while I ran my
mouth over there but man what a comp what a what a combination this is the trl 630d mini skid with
its primary primary focus is on auxiliary hydraulics this is the fmm 148 flail mower and you
have on this side what's interesting is this side is where the the motor is and all the hydraulic
hookups so you can't get too close on this side but the other side is when you got like you can
get like three inches away from the stump over here on this side and just clean it all up and
of course the front you can angle of course you can angle this with the curl of the loader so that
this touches the stump before the rotors do or before the cutting edge does and you can get
really really close such an awesome awesome setup let me jump in and pause for just a second talk
about the sponsor of this video which is brunt you know I've got so much brunt stuff now it's all
good stuff these are the bull duck boots and they are a slip-on boot which I prefer for a mud boot
so these are waterproof you can get them with or without waterproofing but I wanted to get
waterproofing so that way I had a dedicated go-to comfortable rainy crummy kind of outside day
so these are my waterproof mud boots and dirty mucky muck boots they are really comfortable
and that's because on the inside there is if I can pull it out a pretty nice cushion insole now
I've been wearing the snot out of these so this is probably filthy and stinky but anyway
nice squishy insole to go in there there's another one that goes down below it right out of the box
but you remove that if you want a little bit more of a relaxed fit or like me you got really wide
feet and you take that layer out and you got a much better much more comfortable fit for a wide
wide foot foot foot I just combined boot and foot it's a foot anyway I really like these boots
you can get them with or without the waterproofing with or without a hard toe this is the soft toe
variety the soles themselves are really comfortable and I can actually squish them with just with my
fingers soles are comfortable they are heat resistant up to 572 degrees fahrenheit they're
slip and spill resistant and they're barnyard resistant you know what happens in a barn right a
lot of stinky stuff going on well just hose that off at the end of the day anyway if you want to
check these out I really like these boots I also have the the marrons there we go the marron boots
those are my daily drivers now they're a little bit shorter I don't know how tall this is but
the marrons come in a six inch or an eight inch shaft length and I got the six inch so they're
my daily drivers these are my mud boots lots of other great stuff from brunt I've got their pants
and shorts as well check them out if you do want to check them out I'll have a coupon code that
you can use to save a little bit on your first purchase oh and also you can try these on the
job if you if you don't like them after wearing them on the job send them back that's pretty cool
not a lot of not a lot of companies do that I don't know another company actually that does
that not a single one anyway uh check them out if you're interested use my coupon code to save a
bit of money and thank you brunt for sponsoring this video the temperature just dropped like 20
degrees storms are a-brewing though storms are a-brewing man it does feel so much better out
here I got the outside work done ish I got a I got the wrong plate cover for up there so I got
to change out that plate cover sooner rather than later because it's it's open gap for uh
dirt daubers so I've got a GFCI plug right there uh line coming in load going down and I've got
this hose reel or cord reel attached to or plugged in right there uh yeah I got the wrong plate for
that box no big deal I'll swap one out I got to go to town later tonight anyway so I'll swap that
out pretty quickly and easily that's not done though and it bothers me all right coming down
the conduit we have just a pair of duplex receptacles down here everything's outside grade
that reset that GFCI is a 20 amp GFCI these are 20 amp outdoor rated receptacles that's
outdoor rated up there as well and it feels feels good to have some plugs out here that's for sure
uh this cord reel you're kind of have a little bit of force when you pull on this so the bottom
you see it kind of bend in a little bit I don't know how that's going to last long term if that's
going to damage this panel or not if it does damage the panel I can take it off and put an
intermediate plate right there but the top screw is in line with those screws right there that go
through the actual steel structure so the top one is mounted nice and strong all right let's go
inside all right inside I was able to pop through below that structural member this is kind of like
z channel it goes down back and then down again so there's the uh inside of it right there so
the pant the screws on the outside are secured to this bottom row right there and then that leaves
kind of like a trough on the top of this uh well right there you see I got paint cans up here it's
a nice shelf that goes all the way around the shop I really like it but it also adds a visual
blockade for anything that's up there so you can't see where I pop through the wall right there
and I covered it up with some gorilla tape as far as the insulation but the Romex goes through
the wall and it's stripped right there so it goes through a bushing right into that box
and because of there's a bushing there none of that touches metal which is good
coming up through here and I have a dedicated 20 amp breaker for that circuit which is really
really nice all right remember me knocking the spider webs down like a week ago
they're back it's like it's insane it's like this Halloween spider web decoration thickness
in one week it is just insane all right time to turn this on add that to the list of things that
are stupid simple that I should have done sooner oh my goodness I've had that cord through the
wall for the past year and six months anyway the only downside of the GFCI being up there is
I'm short and I need to have something to stand on in order to reset that however it is outside
so I did want a GFCI as the first plug or first receptacle on the line so done check the box
and I need to get this or I'm never going to find it again it'll be right in front of my face
and I'll be looking for it all right I've got to get this uh tire fixed on the tractor but let me
tell you something I just ate probably the best grilled chicken I've ever made in my entire life
and I've made a lot of grilled chicken it was so good and I ate quite a bit of it now I don't want
to do anything but this tire has to get fixed because I need the tractor tomorrow so onward
well it's it's about as flat as flat could be and my air hose won't reach out here so I'm going to
try and get it to the shop or to the lean-to right there without breaking it off the rim
we'll see sometimes you can get lucky and find it without using soapy water
did I just find it no yep I found it right there there it is right there this camera doesn't focus
close but you can hear it all right that should be an easy plug fix and with that I think all
four of my tires will have at least at least one plug this is the last one first step we're going
to take this needle out of here I'm sure it's got a specific name but this little valve in here
we'll take it out to exit all of the air to make the patch easier I think I just said patch
I meant to say plug let's ream it out just a little bit first ay caramba you don't want to
go in there well let's make you go in there oh all right let's get the plug ready well I hope
this works because I'm on my last plug these are one of those things that just keep extras on hand
I need to uh learn from my own words right there to keep more more on hand I hope this holds I
normally like to use two plugs on these big tires but is what it is only have one put a little bit
right on the opening whoop that's a little bit more than a little bit and then load this dude up
these little repair kits usually come with some rubber cement well they do come with rubber cement
and usually you have some leftover which if every kit comes with it and you have some leftover that
means you should probably use some more so I typically make this sloppy just so there's a ton
of this stuff on there find the hole again I just covered it up where did it go is that it right
there is that it where is it there it is plug goes in quite a ways and then we pull this out
that's in there a good little bit make sure that's all the way around there
push and wiggle push and wiggle and there we go I do need to cut that off but I'm going to wait
until I put air in it make sure it's not leaking now the valve goes back in which I put where I
wouldn't lose it and I've lost it already I think no it's down in there okay valve goes in air goes
in and we watch for bubbles I do not see any bubbles all right I'm going to go ahead and
cut this off now that I don't see any bubbles leave a little bit sticking out but keep it lower
than the tread and hope that that was the only one I didn't check to see if there's another one
maybe I should do that right now oh there's another one darn it ah I got another one right
here okie dokie well got one of them fixed I need to go get some more patch material
by the time I get back from the store I got to run errands anyway it's already late
it's like 7 30 at night uh I'll probably just put that next one in tomorrow morning well I
guess I guess I should go ahead and take the air back out and uh go ahead and ream this hole out
so I know where it's at all right no matter how crazy or chaotic the day is the sunsets are always
just lovely especially when there's clouds in the sky and you see this reflection all these
beautiful oranges and blue on the background sun's actually setting over there but we're
looking at a reflection but I just love looking up at the sky at night especially on a clear sky
at night and you see just about every star in the sky where we live we don't have all
all kinds of light pollution it's just it's just lovely today was a very chaotic and crazy kind of
day holy cow look at man look at the sky behind me isn't that crazy gosh I love that I love orange
in the sky um and it feels like everything's turning orange right now it's so trippy at golden
hour when the sun sets and everything just changes colors you know it's just anyway I like it so uh
did a bunch of running around this morning checking a bunch of boxes feel like I got a lot
of stuff done around the property which is great Jamie even mentioned it she said I think you have
a very productive day today and I think I did too so makes you feel good at the end of the day uh
what doesn't make me feel good is I've got to go get another patch and do that first thing in the
morning plug I keep calling it a patch a plug need to get another plug and get that done but there's
a lesson here for any youth out there watching learn how to fix things on your own learn how to
create things and learn skills that you can actually use in life like electrical skills
just today I ran a bunch of electricity and patched a tire put a plug in a tire both of
those things would cost you a decent amount of money if you had somebody else do it so the more
you can learn to do things on your own the more freedom you will have more independence you will
have the less relying on somebody else you will have and more money in your pocket I think that's
it for me today though the sky is so distracting I'm just gonna stand out here and stare for a few
minutes I'll talk to you guys in the next one