Hi, I'm Mike with House on the Mend, and in Episode 3 of our Work Travel Van Build series,
where we are outfitting this 2018 Ram ProMaster 2500 High Roof, we're going to be installing these
rear passenger seats for the kids on this steel pedestal that I fabricated,
complete with full extension drawer slides and USB charging ports. So let's get started.
These very comfortable seats have adjustable spring-loaded shock absorbers which are built-in,
along with armrests and seat belts. They're actually tractor or forklift seats made by
Vivor, and they are available on Amazon. Click the link in the description below
for the entire set of measurements as well as current pricing.
Speaking of clicking, please hit the thumbs up below as well. I can't stress enough how
helpful that simple gesture is to the channel. It tells the algorithm that people enjoy this
video and it should be suggested to more viewers like you. Well, let's unbox one of these seats,
and I'll show you the packaging and setup, and then I'll show you how I fabricated this
pedestal out of common tube steel. So the seat comes folded down with the armrests
disconnected, so there is a small amount of assembly to be done. And this guy's heavy,
weighing 76 pounds. I like this little styrofoam cover over the dial here,
and right in here we have the instructions, and then these are the plastic covers for the
armrests. Here's the lap belt. All right, over on the left-hand side there's a lever that you pull
up, and that is to adjust the seat. So there's a wide range from like straight up to about right
there, so that's quite a recline if you see that. This headrest is not adjustable, it just comes out.
So it either slides in like that or comes all the way out, but not actually adjustable for height.
So to get the plastic off is quite a pain. You actually have to remove the screws in the back
to take the cushions off, because the plastic has been wrapped around and stapled with the
same staples that the upholstery is secured with. There we go. That's quite a bit of work,
just to remove some plastic. All right, there's all the plastic off. Now I will say while it's
a pain that you have to remove all the cushions to get the plastic off, it is kind of neat how
easily these cushions come out. If you need to deep clean them because something got spilled
by the kids and the drink went down here and it's pooled up on the bottom and leaking out the sides,
you can easily take this cushion off and clean up. Or if in the eventuality that this cover
wears out or tears, you could put some foam down here on this side and then reupholster it just by
taking it off easily and stapling on some new upholstery. All right, the armrest installation
is pretty straightforward. You've got this adjustable up and down slots cut in this
piece of metal, and then this guy, once it's in place, will pivot up or down into into use.
These two bolts here, one is a nut, one is a bolt. They're both half inch, which is nice.
All right, once I'm sure I like the height of the armrests, I'll cinch them down and then they come
with these nice plastic covers that just click into place at a little open hole there on the side.
So that's for a little bit later. The lap belt is very standard. It's adjustable on the right hand
and it clicks into place on the left, tightens down, stays tight, no problem. Those are both
bolted down on the side right by the your hips. So as you can probably tell from the thumbnail,
this is what we came up with. We are on the driver's side, behind the driver's seat. This is
going to be a window. There's going to be another window on the sliding door. These seats are going
to be a total of 47 inches from armrest to armrest. There'll be about an inch or two in between the
two seats. We're going to do a 10 inch lift, which is simulated by these two crates, and that'll give
us a seat height of this low or this high. We had the girls come out here and sit. They were both
pretty comfortable. Eventually we'll have a swing out table where they can eat or do schoolwork or
play games. So the key when I build the frame underneath is to make it so we can still utilize
the lever to move the seat forward and backwards. I want to be able to move the seat forward enough
that the girls can recline these seats back and then put a pillow and lay against one of these
frames and the window. I think that will add some comfortability during long drives. Now for the
frame, I am going to use this one and a quarter inch by one and a quarter inch box steel. It fits
perfectly right in between the channels of the floorboard, which is actually about two inches
wide. So I could have gone with an inch and a half or up to two inches. This was available at my local
store, so I'm going to go with it. The key is going to be to get underneath the van and find out
what point I'll be able to mount such a frame at. I've already been under there and there's
definitely some parameters we have to take into account. Mostly how far against this wall we can
go and then there is the muffler running through this area about where my feet are and there's heat
shielding down there. After determining the height I wanted to have the seats at, I cut out the pieces
for the front and rear face frames, which are identical. I then joined the two face frames
together with cross supports long enough for the mounting rails of the seats and fitting within
two low spots in the floor. The upper cross supports are flush with the tops of the face
frames, so the sheet metal skins will easily cover the top and sides. For the bottom supports, I did
something a little different. Now I'm going to have two pullout drawers here, so when it came time to
do the bottom supports, I knew they had to be elevated because of the corrugated metal floor
in the van. So what I did is I raised them up so that they were just at the top of the bottom rails
here that are going to sit in the lower depressions of the corrugated metal. And by raising those up
that high, that allows the full extension drawer slides to be mounted right to those bottom support
rails. All right, I got the frame set in here temporarily, and I got the two seats resting on
a piece of pegboard, and that allowed me to center the seats to these window openings. So,
as we've talked about, this frame here and this sheet of metal are all coming out eventually for
the window. But while it's here, it gave me a perfect opportunity to center the headrests
in between the center support and each side of the window opening. So the way I did that was I
reclined the seats back as far as possible and then just made a little mark with the center line
of the headrest and measured across to get them lined up. That's not going to be centered on this
opening nor centered on the frame itself, but that's okay because I'm utilizing the most amount
of room for the drawers as possible. So the measurement that I came up with for the length
is 46 and a half inches, and that corresponds to the distance between these two pieces of aluminum
that I did for the subfloor. And then I have that sheet of plywood that comes across here,
so that works out perfect and it maximizes the under seat storage space. It's going to give us
plenty of room right here for a USB port as well as a drink holder. There'll be room over here for
a drink holder as well, be it off to the side or mounted right on top, whatever I can find online.
And this seat, by being centered here, gives just enough room from the driver's seat that
you don't feel like it's encroaching on you. All right, so once I had those seats centered,
I was able to come down here with Sharpie and mark the center line for these rails here,
which we'll use to bolt the seats down to the frame. And now that I have all those marked out,
it's time to weld in those final pieces. All right, I've got all four cross supports welded
in and ground down smooth, perfectly lined up with the seat rails. I've got the seat rails
slid forward a couple inches so that I can get access with the Sharpie in there to mark them.
And I am going to drill these four holes up front first. I'm going to attach the seats to the front
bolts, then slide the seats forward so I can get an exact mark in the back, right centered on
these rails. And I want to do that first before I attach this nice big piece of sheet metal,
so there's no way that I'm off in lining up the seats with the cross supports. Then after I
attach the sheet metal, I can come back from underneath and drill through the sheet metal,
no problem. All right, we're bolting down our seats so we can slide them forward and get our
back marks. The bolts that I'm using for this project to attach the seats to the rails and
the frame to the body are grade 8 bolts, and those typically come in this kind of
anodized gold color. But more specifically, they have six radial marks on the head, and these are
high, high strength bolts. In fact, they have a tensile strength of 150,000 pounds per square
inch. So this is what you want for this kind of a project. Most bolts that you can buy at,
you know, Home Depot or Lowe's or a hardware store are going to be grade 5 or lower, and they're fine
for most projects, but I want to be really safe and get these real high strength ones. I found
these at Ace Hardware. They had a great selection. I'm using 5 16ths for the seats up here because
this little cove that the bolt fits into is pretty shallow, and this one just fits in there.
I'm going to use bigger bolts down here for the actual frame. I have nylon lock nuts as well as
the washers that are in the same grade 8 category. All right, now we'll lift up this handle,
slide them forward, and that'll give us a perfect spot back here to mark for the rear holes.
All right, so I've got all the holes drilled, and I've got the bolts all test fitted through the
frame and then down through the base of the van floor. So what I did is I got under the
van, and I looked and I referenced everything off one of these mounting point holes, and I
took my measurements from under there based off of that little mounting point hole,
and that gave me something to look at and reference to see where I could make my holes
for the frame. And then I made this little card and then came up here to the frame,
marked all that out, and drilled the holes. And then once they were drilled, I set it in place
and then marked the area for each of the holes, and that is good. One thing I want to say is this
floor is very thin metal. It's thinner than this box steel, so I would recommend you get at a
minimum, say, an extra washer like this guy to distribute the weight and the force across there
a little bit. In fact, if you have small pieces of plate steel or something that you want to drill
holes through to widen out so that you're not getting, you're not having all the force,
say, if you get in an accident or something right there on a little piece of sheet metal,
that would be probably be a good idea. All right, now you might be thinking, hey,
with the bolts there, isn't that going to impede the drawers? Well, it's actually not, and it
occurred to me that once we get this installed, we're actually going to be putting our insulation
back, and then our subfloor back, and then eventually also some sort of flooring that's
typically about a quarter of an inch. So we actually have this much clearance from those bolts,
and so when I come to make the drawers, I'm actually going to make them a little shorter than
what the perceived quarter inch flooring is going to be. So, say, right about there, and then I'll
have a piece that's the same color and everything that skirts down below like this, so the drawer
will pull out, and then they'll be almost like a toe kick, but it'll be flush. All right, so the
next thing to do is take all these bolts out, now that we've test fit them, and I'm going to
take mineral spirits and clean off the top of the frame so that I can affix the sheet metal to the
top, and then I'm also going to take bondo and mix it up, and since this front face will be seen
when we pull the drawers out, I'm going to take bondo and fill in around all the welding points
so that I can sand that really smooth, and we won't see these little imperfections in the metal.
So let's do that next. I want to have enough to sand, but not so big that it's going to take me
forever to sand. My jigsaw made fast, clean cuts in the sheet metal. I'm only covering the top and
two sides, leaving the rear exposed. Now, welding thin sheet metal with my skills usually spells
disaster, so instead I chose to adhere the skins with a two-part epoxy. This also prevents any
rattling from the vibration when the van is running. Next, it was time to make the drawers.
I chose half-inch cabinet-grade birch plywood for the boxes and drawer faces. So I'm going to be
using a semi-transparent white paint for the front of the drawers and that bottom base that we talked
about. I made a bass guitar with the kids, a DIY project, and I really loved the way this
semi-transparent paint kind of showed the grain coming through, and I want to repeat that on
these drawers. So I want to have the grain an exact flowing match all the way through the project,
so I'm going to cut the bottom strip and then cut the drawers, the two faces of the drawers,
out of this one continuous piece so that the grain matches up. And when we're all done,
it's going to look just like this. And so now we have an eighth-inch gap between
the bottom kind of toe kick and the actual drawers, and then we have an eighth-inch gap
between the drawers, and that'll be some nice lines for the cabinetry work. I protected the
boxes with two coats of clear satin polyurethane. I used wood glue and finishing nails to assemble
the boxes. All right, I'm so excited to show you the progress. So after painting the entire box,
which you saw, I then assembled the cabinet drawers, and I'm putting the last one in right here.
Good. And they're soft close, which means they have springs in there that'll hold them in place
once they're closed, so I'm hoping that will be enough to hold it shut while we're driving. If not,
you can always put marine latches in after the fact. We still need to put the two front faces
on those drawers, but we'll get to that. I cut out a piece of the original foam insulation,
a perfect rectangle that went underneath here, so that's still insulated. And then I cut from
the original piece this one that is about four inches wide that goes in behind it.
Same thing with the subfloor piece that goes in there. Then I cut these little guys
to fill in here for when we eventually put in flooring or put 80-20 cabinetry over them.
Then, so there'd be more support for this field of insulation, I made this cross piece here,
and I made another one up here that's going to run across and make a nice clean front edge,
so that when we put down the foam insulation, it butts right up against that piece of aluminum
there, and then we're going to have a piece coming across here, and all that will help to support
the flooring. There we go. All right, and then I got these off of Amazon here. These little guys
are USB ports, a double USB port, DC, so when we wire this up, we'll wire it up to 12 volts DC.
Now, the nice thing about this one is, unlike most of them where you have to drill a large hole into
the wall, or in this case into this metal facing, and then screw in from behind, this one is flat
and flush mount, so you just pop off this little cover plate here. There's two screw holes, so all
I'm going to have to do is drill one hole, small for the wires to go through, and then I'll be
able to use machine screws, just like I did when I mounted these full extension drawer slides into
the metal. That'll hold right there. It's got a nice rubber cover on it, so that if the girls
spill anything, and hopefully this is closed, then it should be protected. All right, here's the drawer
face. So now, how do we make sure that we get a nice reveal on the bottom, and then it's not
off to one way or the other, but level with that bottom piece of trim? Just like they do
when they put up shiplap, they use a nickel distance, so I'm just going to take two nickels,
line them up, or excuse me, set them down, and then set this face right on top of those.
Now, I've already pre-drilled for the handles, as you recall, so I'm going to use those screws,
or excuse me, those holes, as the spot where I'm going to put some screws in.
So, I've got my works drill with the drill bit and the driver. I just love this thing for
medium to light duty kind of stuff. Take a wood screw, just going to temporarily
hold it in place right here. Now, I can slide that out, and I can attach the face from
inside the drawer with these screws. I'm going to take my little drill driver,
switch it over to drill bit, pre-drill those holes, switch over to the driver bit,
and start sending these home.
Now, we're affixed from the back. We can now take off these
screws, and we'll drill right through those holes so that we can attach these handles.
Look at that. That is great. So, on both ends of this frame where the box steel comes to the end,
there's these open spaces here that I'm going to cover up with these
plastic filler pieces I got off of Amazon. So, they just go right in there like that,
soft mallet, and that dresses it up really nice. And here's the final product. I keep a large
organizer in this drawer for grocery shopping or going to the beach, and this drawer over here has
various ratchet and tie-down straps. We took a recent trip to California for a softball tournament,
and my daughter and her teammates sat back here very comfortably.
Justice gave her teenage stamp of approval at one rather bumpy portion of the highway when she said,
these shocks are crazy, Dad. So, if you found this video helpful, will you please give it a thumbs up?
It really helps the algorithms to start suggesting it to more viewers like you. Also, please consider
subscribing. I'm working really hard to put out good quality content, tool reviews. As long as
this van build, there's a lot more videos to come. And it's free. All you have to do is log in with
your account and click the subscribe button on YouTube, or if you're on Rumble, the follow button.
It really helps the channel. Now, I'm going to leave a link to the seats, the USB port, and also
these end caps that I used on the frame. Now, full disclosure, those will be Amazon affiliate links,
so if you click on them and end up making a purchase, it won't cost you a thing, but I do get
a small reward at the end of the month. The rest of the items that I used for this build are all
available at any hardware store. Now, our next video is going to be installing the windows.
There's one on either side behind the driver's seats, as well as on the back doors. I'll show
you where I got them and how I installed them. But before we go, we've been keeping track of the
running costs, as well as the weight that we've added to the vehicle, since it has a weight limit
of about 4,000 pounds. So, the two seats were $668 with tax, and they add 152 pounds. I used
eight one and a quarter inch, four foot long pieces of tube steel that cost me $336 and added 33 pounds.
The sheet metal was $28, adding six pounds. The birch plywood was in two different thicknesses,
half inch for the face and the boxes, and then quarter inch for the bottom. Those cost $54 and
added 19 pounds. The drawer slides were $20, adding four pounds, and the paint and polyurethane cost
about $20. That gives us a subtotal of $1,126 for this project alone, adding 214 pounds.
If we add the cost and weight from episodes one and two, we are running a total of $2,181,
adding 469 pounds. So, I'd love it if you leave a comment below, ask any questions,
anything I haven't covered. Until next time, thank you for watching.