Hi, I'm Mike with House on the Mend and in this episode of our ongoing van build series we're
going to be focusing on the initial stages of our electrical system. So I'm going to talk about this
rack that I built to house the batteries and we got a wheel well here so underneath I have hidden
all the electrical components. So if you think this might be helpful for you will you please
give it a thumbs up. All right let's get started. So for our electrical system in this van you know
from a previous episode that we've put 700 watts of flexible solar up on the roof. Very low profile
so I can still go through drive-thrus and things like that. I can still park in our garage without
ripping off half of our work. Now down here into the bay of the van we've got three 200 amp hour
batteries. These are lithium ion phosphate. These are Ampertime batteries. I got them off of Amazon
and after watching a couple reviews the only concern with these batteries was the battery
management system inside did not have a low temperature sensor or freezing sensor. So the way
I circumvented that issue with still going with very affordable batteries is to use Victron
components for the charger the smart shunt and this little guy right over here that will be
set down on the batteries and is a temperature monitor and will stop the charger from charging
if the batteries are at or near freezing. Now the other components I have are a smart shunt here.
I have two big bus bars. I have emergency shutoffs right here by the door for both the battery
and the solar panels. In this drawer here I have the a breaker headed to the DC system
and then two things over is going to be our next episode where I'm going to put in a 3,000 watt
inverter. So in this episode I want to show you all the various components of this rack
made out of 8020, how I made the doors, how I bolted everything to the doors, and the reason
why I hid everything in this manner where it's still accessible but it's not out here where
things can bump into it as is if you remember during most of the work week this is my work
van. I have all my tools set right here underneath what will eventually be the bed. So I don't want
to be sliding tools and things in and out of here ladders and whatnot and have anything
arc off on my electrical system. So I want it of course accessible with the doors but not exposed
and so this is the system I came up with and we'll go through all the components.
So this is the cage that all the electrical is going to be housed. It's obviously made out of
8020 extruded aluminum and then I used beadboard plywood for all these front panels. These cool
red latches are how I hold it up and then I have piano hinges there on the bottom. We'll talk about
all that. Let's move around first to the back. This is where when you open the door to the van
in the garage you will see this view right here and so with just merely opening the van doors
we can get to the emergency shutoff for both the battery and the solar. Now let's take a look
inside how that's wired. Big robust double lock cable. I'm going to adjust the iso here a bit.
There we go and each of those shutoffs goes right to a fuse. One of those is obviously is going
straight from the solar and then going to the solar controller. The other one is coming down
from the batteries. I hold these in place if you see right here with angled aluminum that I just
put a little bit of adhesive foam weatherstripping on and those are working really good. Nice and
quiet. All right we come around to this one here and when we open that up we can we have access to
the solar controller and then the two bus bars the positive and negative. Coming off of the positive
we have this one which will be going to the inverter. This one here is going right to the
next panel for the DC bus. This line here is going up to the charge controller and then this one is
coming down to the bus bar from the basically from the battery. We step over to the negative
bus bar we have this one that's going to be ground to the van once we load it into the van. I have
two lines here one going to the charge controller the other one going to the next panel over which
is the DC controller. This one here is yet to be hooked up but that's going to go to the inverter
and then we have the one coming straight from the battery to this side of the smart shunt
and then hooked up to the bus bar itself. If we step to the next one we have the line coming in
to a fuse breaker and then jumping across here to our whole DC circuit panel and then this is the
negative coming in from the bus bar. Now originally I thought I would do the positive bus bar on this
side and then the negative bus bar on this side but come to find out I had more than enough room
on that first panel so this one here is actually going to end up being storage and it'll be
about 12 inches deep and about what 18 inches or so wide and tall so it's going to be a nice little
piece of storage. So all the connections are with this very nice wire. I'll leave links in all this
this is all stranded wire you don't want to do solid core and all the lugs here that you see
I crimped on myself and then after crimping on the lugs I put a shrink wire on there and then
put conduit plastic conduit to protect it from any kind of wire chafing. Let me show you exactly
how we do that and all the tools involved and we'll make a couple pieces right now.
All right let's talk about the wire. It's cutting, it's crimping and protecting with
the heat shrink wrap. Let's go over all of it. So the biggest wire I'm using is 2-0 or double
aught and that is really thick. This is a big battery cable also what welders use. Now
I am using stranded wire. You never want to use solid core in any size in your van because
the stranded wire holds up better to the vibration of driving around over land.
There are at least a couple types readily available of this big double aught. The
stuff that you buy in Home Depot or I bought this in Lowe's is stranded but you can see here it's
big strands that are wrapped together. This stuff is going to be good for runs
that are relatively straight but if you're winding around or any kind of curves or
bends this stuff is flexible but it's not very friendly. Way better is this awesome stuff
right here. This is Windy Nation Power Flex. This is the kind of cable that they use for welding
and it is super supple and yet it's the same thickness core so I love this stuff. I'll leave
links to this. You can buy it in kind of short little runs if you want like I did and if you do
it comes with a little pack of the lugs and some of the heat shrink so this stuff is the best
available on Amazon. Heat shrink like I said this came with the kit if not you can buy it in a thick
enough gauge it looks like overkill but it'll go the lug can easily fit over it right so that's
why it's so big. If you get stuff that's a little tighter just slide it on first and then put on
your lug. To cut this wire and anything smaller I purchased this ratcheting wire cutter and you
bring this around set it and then with one hand I can ratchet even this double lock cable. I bet
that heavier stranded stuff I bought at Lowe's might take two hands but this stuff I can do
one-handed. My only gripe with these because otherwise they work great is when you get to the
last tooth right there it looks like it goes all the way through but it always leaves a little bit
of the insulation left that you have to kind of pull off of both sides. If I had one critique
on these ratchet cable cutters it would be to put another tooth in like that so it would
really pierce that the full strand of the wire including the insulation but it's really easy
to reset you can just wrap it right back around again after you cut it and start over so I do
like these. All right we're going to need scissors for cutting our shrink wrap. I have a knife that
I'm going to use to cut off the insulation then we come to the crimpers. So I love these
crimpers that I bought. When they're done they have like an octagonal crimp on the lug
and it's just so professional looking I think it's great. I only have two gripes about this
little handheld unit because I can do even these big ones by hand really easily with the mechanical
advantage and the hydraulics of this. My first gripe is that the the on and off to me seems to
be backwards so you have to turn it to off to actually make it work and then when you want to
release it or take it off you have to turn it to on so that stickers backwards in my opinion.
I am left-handed so you know write in the comments if somehow I'm mistaken.
Now it comes in this really nice case right here and it comes with all these various different size
crimping lugs which is which is great. It wasn't very expensive at all this is definitely not a
professional set in my opinion it's something for hobbyists like you and I. My second gripe
is that this chart right here so if you're using in our case double-aught wire it says to use the
size 70 die that is this big one right here. Well if you use this die for these double-aught lugs
you can actually pull the wire out it doesn't crimp it enough and I have found with every
gauge I have used it for so double-aught four and eight gauge that I've needed to go down
one step from this chart that they gave so luckily we have the die so it's not a big deal
but that's why it's a minor gripe. Once we're finished making our cable
I want to protect it a little further than the insulation with this plastic conduit.
Now there's two types there is the most typical type I've ever seen which is this which is called
split loom where they've cut it for you so you can get it you know right there around the wire
but they also make and watch out for this they also make solid loom and I bought some of that
and it doesn't fit through there so if you end up mistakenly buying that on Amazon it's no problem
you can just take a pair of scissors like I did with a different piece and just go and cut it
it cuts really easy. For this instance here this is going to be the cable going from the battery
shut off up to the positive terminal of the battery so there's actually a couple sections
that I want to leave relatively exposed one section running down the door our little access
door because I want to be able to put a cable tending clamp right there to hold it onto the
wooden door and then when we get up to where it's going to come around and go across to get to the
battery terminal I want to have there be no mistake that this is a positive cable so in that case I'm
in this case I'm just going to put the conduit over a smaller than typical portion of it but
we're going to go through that how we do that here in just a second and I have really come to
like so far this fabric tape rather than electrician's tape when you pull apart electrician's
tape that part that stretches tends to curl and and it loses some of the adhesive value on
in my opinion so unless you want to cut it constantly with a pair of scissors which obviously
you can do I have come to really like this this was suggested by the Amazon site when I was
buying the conduit and this stuff is really easy to tear so when you're working right here you're
not having to switch over and pull out a pair of scissors or whatever I just I think it's working
great for me so far we'll see how it holds up so let's get to crimping on this terminal this
this one here this big 3 8 lug is going to go on the battery itself but I have this smaller 5 16
for the breaker fuse now we want to cut off this
insulation and what you do is just measure right about to there it doesn't compress very well
into here so it's better to be just a little bit past because we're going to cover that up
with heat shrink later so if you want to go a little past that that's what I have found is
pretty successful and you can see right here with a sharpie I made that mark so let's grab my
razor knife here and I'm just going to cut around this has got the thinner core wire so just be
kind of gentle going around all right so I like to give it a twist like that when it's starting
to come off to pre-twist that cable then we need to think about the what the cable wants to do so
it's been like this in packaging for who knows how long it's been rounded this way I know that
this lug is going to be coming down and winding and coming and making a turn immediately so I'm
going to want this lug to be right here to follow that natural bend that it already has
so with that in mind let's mark right there and right there so we know to line it up
this is an extra step I'm just being anal but it's I have found it makes it a little bit easier
then we can preload this guy turn it to off instead of on I'm going to get it started just
right to the end of that horn where it's just biting and now we've pre-spun it pull it off
and it goes right into that lug look at that nice all right I'm going to hold it in tight
got our lines right there together and I'm just going to start going you can see the jaws
starting to compress and that is really not that difficult I'm resting on the top of my
contractor's table saw here and it is not that hard when you get to here where there's just
like tiny little fractions of a millimeter left and you give those pumps then it gets a little
tougher but once it's completely compressed that's it we turn it to on instead of off
and what we're left with is this really tight lug which is great all right now we want to cover
this connection this one here is probably a little bit better see there's only a small reveal
but nonetheless we're going to cover those up so let's cut about this much right now this stuff is
big enough you can just slide right over the lug that's all that's left to do is take a heat gun
this stuff has adhesive inside of it and you'll see it bubble and be visible on the end here in
there we go nice clean professional look there we go on the driver's side in the very back of
the van is where the electrical cage is going to go and if you see that straight foam adhesive
that's going all the way along that is where the cage is going to sit attached to the van
and i want to have a thermal break there so not only am i using rubber washers at each of these
rivnut locations one two three but all of this right here is this adhesive foam backed insulation
that is very widely available it's made by frost king i got this stuff at home depot
and you can see that this is just the wax paper that protects it here from the adhesive
but it's a nice cushy foam and then on one side is the adhesive and we are about ready to put the
batteries in and start wiring those up so before i do that while we still have the advantage of
taking a look down through the bottom here let's take a look at some of the items and how i
installed them and from the shutoffs we have this positive that's going to go across the battery
and hook up to the first battery this little guy here is going to supply power to the smart shunt
so smart shunt gives us all kinds of great data about how the batteries are doing and how the
solar panels and the charge controller are doing and it has this little green guy right there that
has two wires coming out of it one of those wires is the one i just pointed to that supplies it with
battery power it also allows the smart shunt to track the well-being of that first battery
this auxiliary line right next to it is going to come over here and i have this wire that will
come across and attach to the second battery and it can also monitor the health of that battery
we're going to have three batteries so this one over here i'm going to put on an auxiliary
unit that is also made by Victron and that one will also in addition to the health of the battery
will also keep track of the temperature and then while we're down here here is the negative line
and that's going to go to the negative terminal of the third battery and that way we are not
drawing mainly from this first battery the positive is going to be over here
linked together in parallel and the negative is going to be down on the third one linked this way
in parallel all right these straps are the support straps i've just got them set here
while i've been driving the van but we're gonna pull those back and set them out of the way
we're gonna put the batteries in here and then i'm gonna set up and start wiring each battery
in parallel oh that looks pretty doesn't it 600 amp hours of batteries so to help give you a little
perspective on the size and capacity of our system we have three 200 amp hour batteries that are
lithium iron phosphate when you put those in parallel that turns out to be 7200 watt hours
of usable energy so let's compare that to the very popular ecoflow delta 2 max that is 200 watt hours
so you would need three and a half of those at seventeen hundred dollars each to equal what we
have on board and even if you go with their biggest system the ecoflow delta pro that's
3600 watt hours so you would need two of those at three thousand dollars each to equal the capacity
we have on board now you might be asking yourself mike why do you need so much capacity and it's
true when i was a young military man on my own all i needed was a can of soup that we would place
on the hot intake manifold and we would shower with jerry cans or buckets of water when we were
out in the field however nowadays i tend to travel with at least three women my wife my
two daughters and on occasion our granddaughter when we go camping and when you consider that
they have a certain level of comfort expectation above the mere man air conditioning hot water
heater hair dryer flat iron and charging devices three women is going to equal approximately an
infinite watt hour capacity need so for each one of the batteries i'm going to be installing
one of these terminal fuse blocks so i've got fuse blocks throughout the whole system as you've
already seen but i'm going to add another layer with one of these at each of the positive terminals
they're rated from 30 amps to 300 amps so that should give us some really good protection all
right got everything custom made and hooked up that little guy you see right there
is the temperature sensor and battery monitor for this third battery everything's still shut off
and now that it's all hooked up we're ready to flip the switches and start programming
the charge controller all right moment of truth we are going to turn on the battery supply get
the charge controller going start programming it and then turn on the solar system so it can
start charging the batteries now i'm pretty confident in all my connections but i got a
fire extinguisher right here just in case and i went through before this point and i went through
and reviewed all the connections made sure everything was right and i'm glad i did because
there's actually a little spot on the charge controller that's also supposed to be directly
grounded to the bus bar and i was able to catch that and had to go back it's a super pain to get
in there's really tight spot as you can see here in this video but i made a line out of eight gauge
wire and connected that to the bus bus bar and now we're ready to go all right so i'm going to
turn this battery on i got safety glasses on just in case and that was pretty anticlimactic but
battery's on i'm going to look down here and see if i see any lights coming up on our battery
our controller i'm going to take some readings with this volt meter to make sure that we're
fully charged and running here i'm not getting anything well i figured it out these fuse blocks
that i ordered from amazon had the picture of the actual fuse piece on them when i purchased them
but when they showed up it was just the terminal block no fuse and i'm past the time i can return
it so i ordered 100 amp fuses to go on here and they'll be in tomorrow all right 24 hours later
uh the bus fuses just arrived 100 amp fuses for each one that's what the battery manufacturer
recommends the maximum draw it should be so therefore that's the fuses i chose i've got the
door open got the volt meter ready and i'm going to take measurements to make sure we're getting
power to everything so let's go ahead i got the fire extinguisher let's go ahead and crank this
guy on and see what happens okay now this time i can see that little um battery monitor over there
that eventually is going to be moved back as a as like a freeze detector but i got it up top now so
i can look at it i can see the blue light blinking on that that's a good thing that means that guy's
got power to it oh and i see a blue blinking light on our charge controller let me make
sure it's getting the accurate amount of power yeah 13.26 which i tested each of these batteries
individually they each had 13.27 so when you go through the resistance in the system it's only
bringing it down by 0.01 that ain't bad all right so we're good to go there before i turn
on the solar panels though i want to go into the app and i want to add the charge controller
add the smart shunt add that little monitor over there and then the battery manufacturer supplies
me in their little brochure with all of the various settings that Victron lets you
adjust so you get the the best amount of health in the recharge and draw of the system so i'm
going to fire that up now and program all that in so look at that no sooner did i fire up the app
then it recognized all three Victron devices i have the solar controller that little battery
sensor and then the smart shunt so that's great let's go into this guy and let's start programming
it for the batteries from my understanding its default is four zeros so let's update the firmware
oops there we go all right now we're updated to 3.07 that's quite a different number from the
last one okay let's see if we can get into it now all right let's see if we can go into the settings
yes battery battery is 12 volt max charge current is 100 amps and i know that because this handy
little brochure tells me that the max charging current is 100 amps so let's hit okay all right
i changed the absorption voltage to the charging voltage of 14.4 the float voltage is right here
13.8 so i changed that low temperature cutoff so here's our working temperature range for charging
it's zero to 50 degrees celsius for discharge we can go all the way down to be operating at negative
20 to 60 so prevent damage lithium batteries by disabling the charger during low temperature
conditions all right so let's go by charge condition so we can actually go down to
zero let's just leave it at one just to be safe i guess it auto saves
i would love to name this so let's go in here and save that setting to
ampere time so now let's go into the smart shunt and of course there is a firmware for this guy
just like the charge controller this had to be updated twice because there's been
at least two different versions here and you know what would be great is if we can bring
in the settings that we already changed right heirloom files oh man so they're not interchangeable
all right let's go in we're going to set everything the same now discharge floor is
a lot higher than 50 percent 50 percent is when you're dealing with lead acid batteries
all right so right here we got battery voltage stays above 12 and a half at 90 percent discharge
so that's still high enough to run most of our devices right operating voltage is 12.8
12.5 is 90 percent discharge let's go ahead and change that to
90 percent all right everything's pretty well programmed in now it's time to turn on the solar
panels and see if they start registering so i'm going to walk over and do that right now
solar panels panels are now on there we go
so remember from the other video we've got four solar panels up there 700 watts each one was in
the 20 21 22 volt area when we first turned it on it was looking like what 85 volts which would
have been right about correct there yeah so at or near the end of every video we've been keeping
a running cost and how much weight we've added for each portion of this build since the ram
pro master 2500 has a capacity of roughly 4 000 pounds so for this particular portion of the build
i couldn't do a cost breakdown of the cage there was just too many components when you consider
all the little fittings and fixtures if there's any interest in that cost breakdown of the cage
i when i do the video for the other side of the van when we do the plumbing i'll break down and
show the differences in the ways to save money in some of the 90 degree angled corners and things
like that but i did a rough calculation of the weight when you consider that every inch of
extruded aluminum is 0.079 pounds and you add that with the hardware that's in there
including all the doors we're talking roughly about 75 pounds there the three batteries that
are no longer called ampere time they're actually called lee time were eighteen hundred and ninety
dollars adding 137 pounds the victron charge controller was 590 dollars adding seven pounds
the smart shunt was 130 dollars and about a pound now for the stranded wire i used double lot four
and eight gauge wires throughout this system costing me roughly 120 dollars adding around 15
pounds the two bus bars were 35 and only added about two pounds that gives us a subtotal for
this portion of the build of twenty seven hundred and sixty five dollars adding 237 pounds when we
add in episodes one through five we get a total of seven thousand five hundred ninety six dollars so
far adding 856 pounds all right so there we have it if you found this video helpful you please give
it a thumbs up really helps the youtube algorithm to start suggesting it to more people there were
a lot of firsts in this video for me using this victron system with bluetooth technology to
track how the solar panels and the batteries are doing right off your smartphone all these shunts
and bus bars and things like that so this was very educational for me i really enjoyed it if you have
any questions please leave them in the comments below i'm going to leave links for everything
that i bought off of amazon so that you can check out those links full disclosure these
are affiliate links so if you click on them and end up making a purchase it won't cost you a thing
but i do get a small reward at the end of the month that helps to justify all the time it takes
to set up the camera before producing each piece of equipment here and the cost of producing videos
like this until next time when we work on the inverter over here in this structure thank you
for watching