How to Repair a rounded Corner Wall

House On the Mend
25 followers
8 Video Views·Feb 2, 2026
In this video you will learn how to repair a wall with a rounded corner.
Get the latest price on Kilz Primer using this affiliate link: https://amzn.to/2XpPB6q
Follow House On the Mend on Instagram: @homvegas https://www.instagram.com/homvegas/
Send correspondence to:
House On the Mend
7582 S Las Vegas Blvd Suite 189
Las Vegas, NV 89123
I would love to read your video requests in the comments below.
Hi, this is Mike with House on the Mend. We're here in Las Vegas
in a beautiful master bathroom and today we are going to
be repairing an area of this wall where the plaster has fallen away over time.
As you can see here, we have a piece of plastic
corner molding. Oftentimes when two pieces of sheetrock are joined together
if you don't want a sharp edge, you want that rounded look, you use a
trim that butts up against the two pieces of
sheetrock and then you spackle over that. In this case, it's no different here.
Over time, the plaster has chipped away from
this area, so we're going to zoom in a little closer here
and we're going to get to work on repairing this. To do this repair,
we're first going to clean and prep the area, then we're going to tape off
the tile below it and this wall around it.
Then we'll get out some spackling and we'll start
covering and working that spackling into this area.
That's going to have to dry for some time and then we'll come back,
sand it, prep it with primer and finally paint it.
So let's get started. Alright, so as we zoom in here a little more, you can
start to see that the plaster that had gone over the
sheetrock and over this top surface area and
the rounded corner molding has started to chip away right here. So the first
thing we're going to want to do is clean and prep this area.
I want to start by poking out, clearing if there's any room, clearing out
some of these little holes here where the trim is flexible because that's
going to allow me
to squeeze in some of the new spackling and when that spackling goes through
the back it'll help adhere more to the front of that of this plastic trim
when it comes time to start sanding it and working it.
So we're going to give ourselves the best opportunity for
really good adherence from the spackling by clearing out
these holes here. Let's see, there's not much holding these
on right now. That's pretty good. Alright,
next thing we want to do is open up this cleaner. I like to use
this cleaner here. It's Naptha. You can buy it at any hardware store
and it's a little gentler than mineral spirits and those sorts of things but
still has that viscosity and cleaning and
certainly the fumes but it doesn't take much.
We just want to clean that general area up. We've got soap scum and every other
thing here from the area of a shower that builds up
over time. So just want to make sure we've got the
best chance for adherence with the new spackling. You can see we
did get up some grime there so good. Alright, next thing we're going to do
is tape up this tile area here so that when we're starting to
put spackling in we're not creating a huge mess
for ourselves for later. This is regular painter's tape.
It's a low residue tape. Works great. Comes in blue or some manufacturers
or some versions come in green. Blue or green are my preferred ones.
The green one has even a little bit less
adhesive residue on it. It's for cars and things like that. Paint finishes.
Blue is great for painting around the house and this kind of work right here
for sure. I'm just going to get a little bit more on
there. It'll create a lot less work later when we're
cleaning up. Alright, now I went to the local hardware store and I bought some
spackling. This isn't the the typical spackling
that you buy. That's a lot more lightweight.
This spackling here is actually a vinyl spackling
and that should give us a little bit better
adherence to this plastic. The only trade-off is since it's thicker
and denser it does take longer to dry but that
won't be a concern for us. We've got access to the property for a couple
days. So I'll open it up here. I've got a
knife here that I can put some back onto. So I'm just going to scoop up
probably more than we need for now and then we're going to start working it
into this area here. Try to get it
close to what we need as far as the thickness for two reasons.
One, it's less sanding preparation to paint it later but also it'll
dry quicker. The thicker you put spackling on the longer it takes to dry.
We're going to start by just getting a nice
piece of that here. We're just going to start
working it in. This stuff is very much the consistency of whipped
butter. See I'm trying to squeeze it into those holes we revealed in the
trim. Come back. I've got plenty of working time with this stuff. It's
really soft. It doesn't have to be perfectly smooth. You can have some
stuttering like you see there because that'll all be worked out when we come
back and sand it after it dries for 24 to 48 hours depending on the type of
spackling that you use and how thick it ends up having to go on.
Alright when it comes time to level with the top edge I like to just take
the putty knife. You could also take a big one like this.
You rest it on there and then just drag it across kind of as a makeshift level
and that'll get you pretty close to right in line with the
top surface in this case.
There we go. See that? That'll start to reveal some areas where we're going to
need some more. Primer and paint can fill in those holes as well but
while we're at it we might as well just make it right.
This isn't like two-part epoxy where you only have like a 15 minute
working time. This stuff is really soft. Plenty of time to work it. As long as
there's not any low spots. I'm just going to start
feathering these corners a little bit to give myself
less work in the end. Flat edges, flat tops are really easy to sand
but it's going to take a lot of finesse for the corners so if we can why not
get those rounded as much as possible right here at the start.
Alright 24 hours has gone by and the spackling is
bone dry. That's good. So next thing we're going to want to do
is sand it down. Now we're going to sand it to make a nice
smooth gentle curve and we're also going to be checking
at that time for any possible low spots that may be right in there.
To aid in cleanup I have a drop cloth down on the ground
and then I like to take just an average everyday grocery bag
and tape it right underneath the spot where I'm going to be sanding
or drilling into the walls and that lets all the debris fall right into there.
Makes it much easier to clean up the customer's
house. So I brought out a few options to show
you. There's several ways to sand. This is a
nice little sanding pad, very thin and it can conform to your hand, conform
to the wall and does a pretty good job.
Something I don't recommend for this project but is great on flat walls
is a rubber sanding block like this. You can put the sandpaper
in to hold it in place then you hold on to the block and you can
sand. This is better for flatter surfaces because it's a pretty rigid rubber.
What we're going to use today is one of my favorites.
It's a foam sanding block. When this was brand new
the actual surface right on the foam pad had an abrasive on it that worked great
but if they wear out or if you're wanting it to be
smoother or more coarse than the actual sponge
you can just use a regular piece of sandpaper which is
what I'm going to do. So all we're going to start doing is
sanding down and that'll give us a sense of
how we did. Now as I look here I see several smooth spots and then
several areas that are are low.
When spackling dries it compresses because the moisture is
leaving it. So it's not uncommon to have to come
back and put a second coat on and to make it look really good that's
what we're going to do here. So I'll get a vacuum and I'll clean all
this up and then I'm going to put another round of spackling on.
When we come back I'll have it sanded properly and ready to prime.
All right so I put another layer of spackling on there
to get rid of some of those low areas and then
let that dry and I sanded in the same way that I showed in the last clip
and now we're ready to put on some primer.
I like to use Kiehl's it's nice and thick and it's a
premium product. I pre-mixed it out in the garage
and so what we're going to do we're just going to cover this area here where the
spackling is in primer let that dry while we prepare
to repaint the area with if we're lucky the
same colors left over from the homeowner painting.
So we'll put this on here. Now I like to dab when I put the primer
on because it starts the process of
texturing and copying the texture that's already on the existing wall.
If you see that looks very close to this
so rather than brushing it on and getting brush strokes which can look
really nice on in some types of furniture and thing
here where we're trying to simulate this original texturing
I find that dabbing with the paintbrush works really good.
All right primer doesn't take very long to dry
so once that's complete and it's ready to be painted
we'll come back and I'll have the area taped off
a little bit more because we're going to want to put a little bit more coverage
on that paint to disguise this area if possible
and we'll do that next. All right so our primer is all dried
and I've masked off this whole top shelf
and we're going to just paint this whole top shelf again give it all one
clean clear coat so that it's the same color same texture. I've got a small
roller here that'll be perfect for that. I also have my handy dandy little
brush right here for certain spots I'm not
going to be able to get to with the roller
and a paper towel for cleanup. Now we got really lucky
the homeowner had kept a five gallon bucket of the original paint
this paint was used for the kitchen bathrooms
and laundry room so I mixed it really well
and then I did a test with the color and a q-tip in a couple little
spots that didn't have a ping on them like little scuff marks and it
matched perfectly. I always like to test that paint after I mix it
to make sure that it hasn't aged so much that it's no longer the same color
and I like to test that somewhere other than the high visibility spots such as
this this rounded area in the shower. So
without further ado we're gonna get going I got a drop cloth down here
and I also taped up the baseboard so if any drips go down it'll just make it so
much easier for me to clean up. This paint this tape I should say does a
great job of masking off the grout here where the
tile comes but even though I don't want to get too thick
with a roller I want to make sure it's just kissing
that area so that it doesn't run through the paint and in
certain little areas I'll just touch it up with my paintbrush
as you can see here a little is going a nice long way
let's get just a little bit of paint on my brush with a couple little spots
that the roller couldn't get to
good that's good a couple spots over here in the corner
where it hits up against that beautiful stone
get over there excuse my back
all right so that'll do it go ahead and let this dry
clean up all this tape and we'll come back for a final look
well we're all done and the color is a perfect match
we speckled that area where the plastic was showing through
sanded it primed it and put a coat of the original homeowner's paint on there
I think it turned out really well now you know the steps it would take for you
to repair damage such as this on your wall
if you feel this was a little too daunting for you to take on however
I understand if you're in the Las Vegas area consider giving me a call
I'd be happy to come repair an issue like this for you
until next time thank you for watching
