A Look Inside This Nice Hallicrafters S-20R Tube Radio From 1939ish!

Amateur Repair Time
257 followers
830 Video Views·Dec 14, 2025
Check out our Patreon page, for all of our channels. Contains outakes, concise arcade repair tips, bloopers, repair FAILS, Audio youtube wouldn't allow us to upload, and much more!
https://patreon.com/JoesClassicVideoGames
------------------------------------------------------------------------------------
Ladies and gentlemen, welcome back to
Amateur Repair Time. I have been working
on this uh Hocrafters
S20R
super cool
radio receiver transmitter
Sky Champion
um for a little while now. We had a
friend of ours bring this by my store
and wanted me to see if I'd take a look
at it. he couldn't get it to do
anything. And I think we figured out in
the last video that is pretty much he
just needed an antenna hooked up to it.
And it's a little finicky with how you
tune it because it's it's just got a lot
of different stuff going on. It's got
different u channels so you can do
shortwave and all of that. Um and
without the antenna, you only get a few
solid channels. So anyway, we we pretty
much proved in the previous video that
the thing works great
and
it's still all original pretty much. I
think the power cords been replaced, but
none of the capacitors have been
replaced, which you're going to see in
this video. And the thing worked pretty
freaking good. Um,
it's kind of incredible. It was, we
think it was built in like 39. Maybe
we'll get a better idea of that with
some of the caps here shortly or
resistors. Maybe something will have a
date code on it, but um yeah, it's built
in 1939. It's 86 years old and works
fine.
However, the the gentleman that brought
it by the store um is a young man who's
interested in old radios and things and
uh he's going to use it. He's going to
plug it in and play it. So, it kind of
needs the capacitors replaced. I'm sure
there's some of them that are probably
marginal anyway or causing issues that
just aren't super apparent. Um, so it
may work a lot better once we recap it.
But we kind of need to recap it so that
he doesn't end up burning up the
transformer or something. Um, if the,
you know, the old paper caps and things
eventually they're going to short and
it's going to burn crap up. So,
[laughter]
um, we proved on the last video that it
still worked and, um, I think we're
going to go ahead and recap it. So, I'm
going to turn it up on its end, and
we'll look we'll take the bottom plate
off, get a look at how it looks, all
original, and then I'm going to start
snipping original out and putting in new
uh to get this thing nice and reliable
where he can listen to it anytime he
likes.
Okay, I like uh there's a plate that
goes on here where you have access to
all these trimmer pots so that you can
align it. Very cool.
Just look at how beautiful this thing
is.
I don't see any work that's been done to
it at all.
Maybe we will as we go through it,
though.
Look at that. All original.
Let's see if the power cord though. So,
this is the P. This is where the power
cord comes in. Typically, these wouldn't
have had a ground on them. Um, I mean,
obviously it's not a power cord from
1939, but let's see if we can tell
anything if it's obvious that that's
been replaced.
So, does that look like new solder? I
suppose it is.
Yeah. So, I don't know
when they did that, but at one point
someone has put a new wire, a new cord
on it, and that's it.
[laughter]
I love it. I love it. They must have
tested some of the caps and been like,
"Nope, we're just going to leave it."
All right. So, I believe this is our
filter cap right here.
Uh, we'll make sure with the schematics.
And then if that is the filter cap, I'm
going to go ahead and put in new caps.
Uh, the way I like to do it is like, see
this wire coming off one of them over to
here. I like just mounting the cap over
here. Of course, take the wire loose,
but mount the cap over here. And usually
there's a ground somewhere that it can
get to it. You can put a little terminal
strip in. It would actually be kind of
easy here because you've got this nut
here. you can take that nut loose and
then put the strip down and put the nut
back in place and mount them to the
terminal strip. That's a real clean way
to do it. Um, but if you know if there's
room where the wires are running
through, I'm just I'd just assume put
them on that. Real simple to do. And I
think there's only three in this set.
I'm supposing that's what that is. I
believe looks like it to me. Um, so
yeah,
look at that.
Beautiful.
So, here are the schematics.
Um, what are we looking at here?
Where's our power coming in?
[laughter]
I suppose that's it there.
Look at this little baby waiting to zap
you. That's waiting to screw you up.
Okay. Um,
there's a little bit of an issue where
you can't read this too good. So, that's
C28,
maybe, C29, and C30.
Can't tell for sure what that is.
Those are probably the electrolytics.
And then I have a nice list here.
Yeah, they do have the electrolytics
right there. That looks
Yep, that's what we were just looking
at. Um,
condensers
28,
29,
and then 32 is what I've got.
So 28, 29, and 32.
To the young gentleman watching this
that this is his radio, that little hash
mark there usually means that it just
repeat what's above it. I don't know if
you've seen that before, but like it's a
little confusing the way they the way
they've written it. Look, 20 is one as
well.
Yeah. So we'll have to look into that.
So if you look here where it says like
number 28, it says 30 and then it has a
hash. That means what's above it. So
it's 30 microfarad
450 volt electrolytic cap. And then the
next one is 10.
There's a hash cuz it's still microfarad
400 volt and then a hash electrolytic
cap. And then the next one is 0.1
hash microfarad
200, but it doesn't have the hash. So
it's not an electrolytic.
So it's it's
that cap that should be unnamed,
which is the wax ones, the paper ones.
Um, so it's a little confusing the way
they wrote it, but we'll figure it all
out. All right. So, um h maybe the first
thing we do is put in the safety cap.
So,
since I know he's watching this, this
capacitor right here, the problem you
have is if that cap shorts because of
the where they put it, it's on one of
the AC lines coming in. If that cap
shorts, now you have AC running to the
chassis.
which is what the ground is connected
to. So this whole thing will have
electricity on it if that cap shorts. So
that's an important one. So you can
replace that with what's called a safety
capacitor
which will not short. If it screws up,
it'll open up so that it's not
connected. So if a cap shorts, that
means both legs of the cap are connected
together. This side will be connected to
that. So you would that would connect AC
straight to the chassis. If it's a
safety cap and it opens, what would
happen is this cap, this side and this
side would no longer have any
relationship. So that the capacitor just
would stop working. Um that's so that
would be preferable to shorting. Um
so let's see if we can find that. It
appears to be
right where the wire comes in.
Um where the power the power cord comes
in. So
the power cord
is right there.
One wire comes in. One cord comes in.
And see this is the way they have it
wired. They have it where the switch
isn't connected. The way this is wired,
it's just always got
power.
And we're we're unplugged, by the way.
So, it's connected to pin one
and pin five. And it does not run
through a power switch. There is no
power switch on the back of this thing,
though. So,
h [sighs] that's interesting. So, it's
connected to pin one and pin five,
which let me see if I can find a pin.
I don't know which is which.
Pin five is connected to a wire.
It looks like there's the cap up there,
but I can't tell how it's connected. All
right. So, one wire comes in and goes to
pin five,
which is connected to a couple things.
And then the other one comes in, it goes
to pin one.
And also connected to pin one is a
capacitor.
And the other side of the capacitor is
connected to ground. It's kind of hard
to tell, but that little metal thing
there is a little prong that's
connecting to the chassis. So, that is
that cap that we're looking for.
So, we're going to cut that out and
replace it. Okay. So, I've installed a
Y2
X1 Y2 safety cap on this. I guess that's
marked on the other side. Let me
bend it down so you can see.
Okay. So, it's a Y2 safety cap. So,
there's X safety caps and Y safety caps.
The Y safety cap is for uh when you're
connecting one of the lines to ground
like that. The X is if you're connecting
across the ground and and the neutral
and hot. Um, so that will that will
replace this capacitor
which uh is probably the most important
capacitor to replace cuz if this would
have shorted it would have thrown
your voltage to the chassis of the
machine. Okay. And I figured out the
mystery
if you look. So this is number nine. See
the little wire coming from the winding
inside that's wrapped around this lug.
And then see that one there on seven.
This one doesn't have one. There's no
wire coming out of the winding. So in
other words, number five is a dummy
uh post. There's no connection there. So
there is just using it as a tie off. So
the power comes in to there and then it
connects to this black wire. This black
wire goes up and around
and down to here. This is that that
switch that we messed with last time.
That's the um AC. It says AC on. So, if
you turn that switch on now, the power
connects into the other black wire
that's twisted that goes back around
and connects here to number three.
Number three,
if you look, does have a wire come out
of the winding.
So once the switch is on, this is
essentially connected to here. So the
two power lines connect to one and
three.
Easy peasy. So here's where it gets
tricky. Trying to replace these without
adding in a terminal strip. Now there is
a terminal strip here with an extra lug
on it. And one of the lugs is being
used. So that's two. If I can hide that
third one in there, we're good to go.
Um, so we'll have to figure out which
one this is first. Now, if you look at
the bottom of them, and again, I'm
talking to the the young gentleman that
owns this radio. I know a lot of people
watching know this better than I do, but
I'm just trying to explain to him
because he'll probably be really
interested in this. This cap is a can
that's got three different capacitors in
it. And they're designated, the lugs are
designated by those little symbols. See
that little half moon there? And this
one is a square.
And then, uh, or it's got four caps in
it, actually. one of them. This is a
triangle
and then that one isn't marked. If you
look on the side of the can of the
capacitor, it tells you which one each
one of those are.
Interesting. That looks like a
replacement to me. Wow.
Yeah, I think that's a replacement. I
don't believe that's original.
H. Okay. So, if you look, it says
30 UF 450 volts DC and it's the half
moon. So, the half moon is the 30.
I'm writing these down.
And then the next one is 20.
The 20 is the square.
The next one is 10.
The 10 is the triangle.
And then the one that's unmarked is 20.
That is kind of fascinating.
Maybe that explains why the thing is
still working so well. They replaced the
cap at some point.
I don't I mean I don't know that they
did, but that label just looks so
nice. I think that it's been replaced.
H interesting. So, we run into our first
issue. Since that's been replaced, it
doesn't line up with what this is. So,
we've got a 110,
130,
110,
and 110.
So, we needed a 10, a 10, a 10, and a
30. And we've got a 30, a 20,
a 20, and a 10. So, two of our tens are
now 20s,
which is fine, but we don't necessarily
know which one's which. And we I need
to, you know, it's very important that
we make sure everything's hooked up in
the right spot. It's all right if you go
a little higher on some of them. So,
that's not that big of a deal, but um
you kind of need to make sure that
everything is copacetic, if you know
what I mean. So, I think what we'll do
is um
I guess if we did the 30, we know which
one that's supposed to be.
Uh
that is 28. Can we tell on the
schematics which one is 28?
Kind of has to be that one, doesn't it?
So, we got 29 and 30 there. And there's
28 or and on this it's uh we've got 20
28
29 and 32.
[laughter]
All right.
Did I say 29? Yes. 29 is a 10.
28
20
and 32. Okay, so I figured out my first
one. This is going to take forever. I'm
just trying to film a bunch of it
because I find this interesting. So,
this one right here is a 20.
Um, so we know that two of our 20s are
actually supposed to be tens. This one
comes over to here and then it's
connected to a capacitor
that goes to ground and it's connected
to a resistor that goes to one of the
other electrolytic caps
and it's also connected to
a wire that runs down here. So that is
that capacitor must be
C32.
One side is connected to ground
because all of the electrolytics are
through the can. And then the the
positive side of the cap is connected to
a resistor
that goes to another one of the
electrolytic caps.
Okay. That same line where it's
connected
goes to a paper cap somewhere.
Well, hell. [clears throat]
Well,
I've got an extra cap. I've got a cap
coming from here to ground. So, maybe
that's not it. Unless that is that paper
cap going to ground.
>> [cough]
[clears throat]
>> That stuff ain't easy, people. Okay. And
then the other side
runs over and connects to two resistors
and one of the IF transformers that goes
to the 6K8. The 6K8 is this.
Excuse me. Here's the resistor going to
that red and white wire.
Um, and then there's a second resistor
here.
But we've got
that cap there. I don't know what that's
all about. There's a cap from here to
ground somewhere.
I do not see that. Let me keep watching.
Okay, so this is what I came up with so
far. Um, of course, we did the line cap
up there. And then
one of these caps, I moved the wires
going to it over here. And also I moved
the resistor that was coming from here
to there over to that extra lug that we
had. I had to put an extension on one of
the lines because it just wasn't quite
long enough. And then so that spot which
is now this spot would have been uh the
30 microfarad cap to ground. Uh one of
these lines though just runs over to
this plug on the back. So I just mounted
it there because it's out of the way.
So, I put a 33450.
Um,
you could have mounted it here and then
the ground is right there. That could
work, too. But there's a bunch of crap
going on right here that I'm trying to
figure out. So, I kind of want it out of
the way. Okay. So, then this one, which
was the little jumper wire, all of the
all of the wires check out. That is um
So, the first one was this one. That is
this one
C32.
That resistor is correct. Uh the other
resistors are correct. The wire goes
from there over to that cap that we just
did. The resistor is between that cap
and that cap. Everything's correct, but
there was an extra cap. So they had, you
just saw it. They had this electrolytic
which is a a connection to ground,
right? They had the wire coming from
there to here and then they had a cap
from there to ground. So they had in
parallel an electrolytic cap and a paper
cap, but there's nothing like that on
the schematic. So I took it off, you
know, I don't know if somebody added it.
I'm thinking that this has been worked
on, but it was just a long time ago.
Whoever did it did such a beautiful
clean job that you can't tell, you know.
So, I've taken that out for now because
it's not on the schematic. It could have
been some kind of um mod, but I don't
know why you would have an electrolytic
cap. So, it was this cap and then also
from the same line to ground a paper cap
02.
And it's just not like that.
There is no place that there is a paper
cap. It's it's a actually a very simple
little circuit here. You've got two
resistors and then the RF or the one of
the the
Yeah, I guess that's the
I don't know if that's the RF or not,
but uh one of the the the uh trimmer
pots,
right? There is no other cap to ground
and it wouldn't make sense to have
another cap right beside this cap. So, I
took it out for now. We can always put
it back in later if it don't work, but I
think it will work. Okay, so that's two
of them. I've got two left.
This one, which looks pretty simple, and
then this one's going to be a freaking
nightmare. So, let me see if I can
figure out which one that is. Well,
we've got another one.
So if you look one of the electrolytic
caps goes from the 6F6G one of the pins
on it to ground and there is also a
resistor in parallel to ground.
Okay R25
is a 500 ohm resistor.
Um
yeah confusing as crap. So,
this
of the electrolytic cap runs up to this
pin.
I need to count them to see which pin
that is. And so that's an electrolytic
to ground.
And then we have our resistor to ground,
but I don't think this is 500 ohm, but
we're going to check. And then we have
uh a paper cap to ground as well. So
they must be doing that for some reason.
Maybe noise reduction or something. I
don't understand why the you would have
an electrolytic and a paper, but they
have it on this one as well. So the one
that goes from here to ground,
I suppose, is correct. So we'll have to
put one back in. So we'll put that one
back in and then we'll replace this one.
And uh we can when we do that put the
other the cap that goes here we can put
in parallel with it or in parallel with
this. And I'm going to check this uh
resistor and see if it's 500 ohm. All
right. I'm seeing footprints of people
that were here before me. So there is a
solder splash behind that
that [clears throat] I had nothing to do
with. So, that was in there
like so.
There's a solder splash behind it. I
haven't been working on anything. I
didn't do that.
Um, so I maybe these were redone at some
point and it's just been so long that I
can't tell.
It almost seems like that's a date code
36 L12.
So that would be 36,
you know, and this thing would have been
made in the late 30s or early 40s.
So 36 L12. Now I just pulled out another
one. You know that one that I cut out
and said that's not supposed to be
there.
36 L12. That's the same. So maybe that's
just a part number. Then we have this
one which was the line cap
44
M01.
That those may be date codes. I don't
know.
Okay. So uh yeah, moving right along.
All right, folks. So I took the third
one loose. Took the wire out actually.
Um, and there is a ground right here
next to it. So, it's really easy to put
the cap between where the pin that it's
on and ground. And then I put the 02
back in connecting over to this ground.
I guess they were just doing that
because of
physical stuff just because of the
length of the cap. They couldn't really
connect it right next to it very easily.
So, they just reached over here and
connected it where it was more
convenient. So, I put that back. And
then I put this one back, which was
that's exactly where that one was. It's
just um this cap of course was right
there.
Um so they're right beside each other
now. And so I've got three of them done.
So one, two, three. This other one's
going to be a pain cuz it's got it's
going all kinds of places. So we're
going to we're going to get to that. But
I'm going to go ahead and knock out some
of these other paper ones that are kind
of in the way. So there's one up there.
There's one there. There's one there,
one there, one there.
Um, and I I kind of want to just get
some of those out of the way so I can
even figure out where they are on the
schematic and what we're looking at. I'm
also wondering if too if maybe there's a
a later version of this. Somebody
mentioned on the previous video that
they made these for like six years. So,
it could be that there's another version
of the schematics floating around that
shows those 02s
um that I added back in. So, I'm going
to look look at that and see. Oh, and I
did check this. It's a it's five um 569
instead of 500. But, you know, that's
pretty good. That's uh a little over
10%. I guess that's 14%.
Something like that. Um
no, not quite that.
10% would be 550.
If it's 569
carry the one put the thingah 12 and a
half% something like that it's pretty
close I don't know does s doesn't silver
mean 20%.
So, if I'm at 12 and a half%.
That's pretty good, ain't it? Maybe it
tells us on our little list.
It tells us the wattage. It doesn't tell
us the rest.
I'm going to say 10 to 20% ain't that
bad.
That other one that I checked that was
10,000 was 11,000, so it was at 10%.
I think that'll be just fine. We also
have the added benefit of knowing that
this thing works because we tried it in
the previous video. All right. Yeah, let
me replace a few of these and mark them
off the list. And then we'll uh
eventually we'll figure out what we're
going to do with this toughy
>> offer from Real Estate. There are no
showings, no open houses, and the best
part, there's no stress.
>> So, I've replaced many of them, but not
all of them. But I just wanted to test
it just to make sure I hadn't screwed
anything up. I didn't think I had.
>> We're still good. Now, we don't know how
um
>> good the sensitivity is or anything like
that
>> or how aligned it is because I'm just
picking up the u the clear channel
station. It's four miles down the
street.
>> Um
>> but here's here's what I've done with
the
>> laundry caps that I
>> replaced of course up there at the top.
>> All the black ones are the new ones. Of
course,
fivear reviews. typically don't take
them off of the where they go like
completely remove the old one. I cut the
cut the lead because I'm trying to keep
and this I got this idea from Shango and
I really like it. It they don't look
quite as clean so I could probably get
them looking a little bit cleaner but um
you know I'm not great at it but um what
I do is I cut the lead and then loop it
around and then loop the new lead
through it. And by doing that, you keep
the heat off of the component, or not
the component, but the the um usually
the tube socket. If you heat this up,
one I'm I'm way away from it, by the
way. I'm not touching it. I'm 6 in from
it. If you heat this up [music]
enough, now if you're really good, you
can pull it off. But this thing's 100
years old. If you heat this up enough,
it's going to melt some of this plastic
or bake light or whatever that's made
out of and uh you're going to loosen
that socket up where it doesn't work.
Right. Right. So, I'm trying to keep
that to a minimum by heating up the wire
a little bit away from it. Hopefully,
keeping some of the heat off of the
actual
thing since it is a
relic.
All right. So, I've worked my way down
through here, which is essentially all
of the Do they call that? I can't even
remember if they call it the front end.
This is the front end, right? So,
basically, we've worked through most of
this. We haven't got back here to the uh
the uh RF section yet, or the antenna
section, I guess you'd call it. Let's
see what it says down here. 6 SK7
they're saying is the first IF
amplifier.
Uh and then the 6K8 they are saying is
the the first detector mixer horizontal
frequency oscillator.
Um and then the 6SK7 they are calling
the second IF amplifier.
So the IF is what we've been um out of
so far. Well damn there's three of them.
Yeah. Okay. I was correct the first
time. The first one is the RF amplifier.
So that's the actual antenna. Then
you're moving your way through it,
right?
So we have done all of this. The RF,
this part we haven't done yet, but we're
still working through it. So, but I
think this is a good place to stop for
now. It's going to take forever. I've
been working on it for several hours.
Um,
>> but I'm glad that we're still up and
running. So, next time we'll work
through the rest of the caps and then
align the thing. And hopefully that'll
get us a nice reliable set. It has great
volume.
>> George, that's promo code George at
lifelock.com to save up to 40% off.
Terms apply. Think about December after
all the hustle, errands, travel. What's
the moment you look forward to most? For
me, it's that first quiet evening when
everything finally slows down. And
that's why I love it. Your gifts aren't
just beautiful. It said if you use the
tone control, it can get rid of strange
interference.
>> It said if you put it on high, that's
natural sound reproduction. And then if
you put it on the other two,
>> it will help get rid of some
interference. So, let's see.
>> It's the ultimate gift for curling up on
the couch, movie nights, reading, any
cozy moment you want to make bed.
>> Every Cozy Earth product comes with a
100 night sleep trial and a 10year
warranty. So, this is comfort that
lasts. All
right, folks. So, I think that's a good
place to stop. We will see you next
week. I hope you have enjoyed it. Oh, by
the way,
>> isn't it time for our song?
>> Cue the music.
[music]
>> [music]
>> Ladies and gentlemen,
circuits
[music]
sitting on a desk
been [music] lost in time.
50 years of rest [music]
and schematics
and thrifting [music] old parts.
One more last [music] week.
Oh, board new spots.
[music]
Tracing faded traces. Vacuum to blows.
Get [music] it back to working by the
end of a show.
Bringing broken gadgets. [music]
Back to life. Turning silence into
stories one at a time. [music] We fixing
to fix them. Easy as can be. Amateur
repair time for you [music] and me.
[music]
Little machine carried history. [music]
Time to trace your path. Bring your
sister from open to singing. Time
presets
[music]
tangled up
[music]
patient searches
passing
[music]
[music]
Please start
brand new capacitors.
[music]
Tracing faded traces back [music] into
ghost. Get it back to working by the end
of the show. [music] Bringing broken
gadgets back to life. Turn silence into
[music] stories one at a time. We're
fixing to fix some easy as can [music]
be. I'm a sure time for you and me.
[music]
It's [music] pattern.
[music]
It's bad time.
[music]
