Had To Break out The Vacuum Tube Voltmeter On A 1931 Atwater Kent Radio...

Amateur Repair Time
257 followers
859 Video Views·Apr 19, 2026
We have been working on a 1931 Atwater Kent Model 72 Radio with a Model H Chassis.
Check out our Patreon page, for all of our channels. Contains outakes, concise arcade repair tips, bloopers, repair FAILS, Audio youtube wouldn't allow us to upload, and much more!
https://patreon.com/JoesClassicVideoGames
------------------------------------------------------------------------------------
Ladies and gentlemen, welcome back to Amateur Repair Time. I am knee deep in this Atwater
Kent Model 72 radio that I've been working on. This is a chassis H2 from 1931 and I'm trying
to learn about it a little bit. And so we've done tons of videos on it. We did like a dozen videos
or something so far. I don't really know what I'm doing. It's amateur repair time, but we're
figuring it out. I've actually got it working. I've got it off channel right now because we
haven't aligned it. I'm just trying to get it to make some noise. And we did a video where we took
the thing apart and checked out what was going on. We did a video where we messed with the power
transformer. We did a video where we replaced all the capacitors in the sardine cans, which is these.
We did a video where we did the main power capacitors, filter capacitors. We did a video
where we did some rewiring and stuff where we had the the power transformer had been changed at
some point. We did a video where we tested all the tubes. We did a video where I rebuilt a speaker.
That's not this one though. I've got the other one on the floor. And we're up to, we need to,
and a couple other videos probably, we're up to, we need to align the thing. Try to get it to work
right. I do not have a ground on the chassis either. So there's a, you're supposed to hook up
an antenna and a ground. I haven't figured out how to hook up the ground yet. If I hook up a ground
just to like the power or something, major problems. Okay, so one of the things that I wanted
to check out, we got a little hum too, which might be lights or something. One of the things that I
wanted to check out was I'm running it offline voltage at 123 volts. I just measured it. 123
volts. I've heard people say that you can't do that. It used to be 115, et cetera, et cetera,
et cetera, et cetera, et cetera. And so I've been looking into that, trying to decide how I wanted
to drop the voltage. And then I kept reading and I kept reading and I don't know that I am going to
drop the voltage. I've been taking some measurements. So we'll talk about it here in a
second. The idea that the power was always 115 volts back in the day, apparently is not necessarily
a hundred percent true. From what I'm reading back in the day, you had less regulated power.
So sometimes it would swing wildly. So you might have 107. And then later in the day, you've got
130. The reason people talk about that though, about wanting to lower the voltage on the older
radios, assuming that they originally ran off 115 is because usually in the schematics, it lists
that they're running on 115. This radio is from 1931. And in this particular radio, where that
would matter would be the transformer. This is a replacement transformer, but we looked it all up.
It's a stand core transformer, which apparently they're pretty decent stuff.
So I guess there's just a lot of different ways to look at it, but let me show you something
really special. So this is Atwater-Kent's alignment or voltage table. And look what it says.
Voltage table for type H2 chassis, set in operation, volume control at maximum.
I don't have it at maximum. I did kind of mess with it just to see differences.
Use high resistance DC voltmeter to measure plate and grid voltages. Use AC voltmeter to measure
filament voltages. Now I'm using just a digital multimeter. I don't know if that is going to give
me lower voltages or higher voltages. I don't know, right? Use AC voltmeter to measure filament
voltages. And then look what it says right here. Approximate voltages using 120 volt line.
I don't know, folks. I think we're being lied to. Look at this. January 1931, Atwater-Kent was
assuming that you were using 120 volt line. So I'm looking around on that and I heard a
couple people say that the 115 that's always quoted is kind of like a colloquial. Is that the
word? A colloquial way of putting it because there was such a variation in line voltages
that they kind of designed the sets to where they would take about whatever you threw at it.
Now with that said, there's a couple things to think about. One, this is a replacement
power transformer. So is it the same as Atwater-Kent's design? Two, if your voltage is higher,
your filament voltage is going to be higher. So you burn out tubes quicker. Three, it's an old
transformer. So you might think, well, go easy on it. You don't want to overheat it. Could be that.
So, I mean, there's things to think about. The way I see it, they're built for the air,
people. I mean, turn them on and play them. I don't want to hook up a Variac every time I want
to play the radio. And I don't want to, you know, put a bunch of extra crap in here, extra resistors
and stuff. I don't want to do that. Atwater-Kent's telling me to run it on 120 and I'm running it on
123. I think I'm going to leave it. But here's my numbers. So you can tell me what you think.
I'm sure you will in the comments below. So I've been measuring stuff while the camera
was off. Before y'all got here, I was measuring stuff because I didn't know what I was getting
into. The first detector, the filament voltage is supposed to be 2.3. It's 2.7, as are all the
2.3. So it's high. The tubes that are supposed to have 2.5, they've both got 2.9. And the rectifier
that's supposed to have 4.7, it's got 5.3. So I will concede the fact that we're probably going
to burn these tubes out quicker because they're over-volted, if my meter is measuring properly,
which it probably is. And again, it's a replacement transformer. So, you know,
that pretty much changes everything. Anyway, here's all the stuff I don't understand. All
this is off. But I've measured some voltages in All-American 5 sets before, and the voltages
were all over the freaking place. Nowhere near what they're supposed to be. So I don't completely
understand why that would be. Maybe we can figure it out by looking at the schematics.
So they've got these in order. I don't know if there's a method to their madness.
Yeah, there kind of is, isn't there? Yeah, they're running it in order pretty much, I think.
So the first detector, the plate voltage is supposed to be 150, it's 137. I turned it up
and down. If you turned it up, the voltage actually went down. They're telling you to
measure it with the power, the volume control at maximum. It could be different if you're on
a station. I wasn't getting a great reception. I've got an antenna hooked up, but it's just a
wire and I don't have a ground hooked up. So I'm not getting great reception right now because the
whole thing needs to be aligned. I'm getting 137. The control grid voltage, I'm getting three.
The screen voltage, I'm only getting two instead of 15. So that ain't even close. I don't understand
what's going on there. We'll have to look at the schematics and so I can understand it a little
better. Here's the bottom view of the chassis and it has a couple notes down here. With the
volume control at minimum, the IF screen voltage is reduced to about 15 volts. Interestingly enough,
it says the IF screen voltage is reduced to about 15 volts and I did find that true
on the first IF and the second IF. They didn't say first IF or second IF, they just said the IF.
Use the 250 volt scale on your voltmeter on this particular one so that it would catch it. They're
saying don't try to use the 10 volt scale, use the 250 volt scale. I'm using a digital one so
it automatically... well, I did have it set for 250 or 200. This is the voltage across the detector
bias resistor when measuring from grid to cathode. The voltage reading is only two.
Oh, that explains that. Okay, yeah, all right. We're good then. Yeah, that was one I was worried
about. I was like, what the hell? That's nowhere close, but I was using the cathode because look
what it says here. All readings are made from the cathode in heater type tubes and from the
negative filament in plain filament type tubes. Okay, so if you look here, the rectifier for
instance, it doesn't have a cathode. We didn't measure the rectifier anyway, we just measured
the filament. The 45, the output, the 2A, it doesn't have a cathode. It's got a plate and a grid.
So I measured it from the negative filament and that's how I got my plate and my grid voltages.
But on some of these, like for instance, the oscillator clearly has a cathode, a grid,
and a plate. So it's really easy to measure from the cathode to the grid and from the cathode to
the plate. So that's what I did. So that's how I got all these measurements. And then the
ones, the, what am I seeing here? Oh, the control grid on three of them is actually the
the cap on the top, you know, but the cap is usually the grid on these early tubes. So
on this one, the second detector, I only got two volts, but it was because I was using their advice
and measuring from the cathode to the grid. But they're saying in this particular one, you're,
by doing that, you're measuring across the detector bias resistor. Since I'm measuring
from grid to cathode, the voltage reading is only two. Yeah, so the 14 is the voltage across the
detector bias resistor. So I should be measuring that differently. I'm not going to worry about it
So if we look at our numbers here, the oscillator, filament voltage is as high as hell on all of
them. The plate voltage is low on all of them. Every single one. Does that have anything to do
with the filament voltage being too high? We're going to find out. Because what I'm going to do
is I'm going to hook up a variac to it and lower the damn input voltage however low I need to go.
I mean, I'm at 123, but I'm going to lower it however I need to go and just see if it changes
these numbers. But we may be able to find a tube in here that's underperforming that's
causing us problems or the resistor screwing us up or something. The oscillator, 93 plate voltage
and 10 on the control grid voltage. So that's dead on the money. And again, I'm using a digital
voltmeter. So that might be the whole problem. It's just measuring everything low.
The first IF, it was giving me 137 with the volume turned down and I was down to 18. It
tells you down here that it does that. It goes down to 15 with the volume control at minimum.
My volume control doesn't go all the way to minimum. The resistance in it is a little high.
I can't get it down to where it's quiet. If I get a really loud station, it's loud as crap
because there's no AVC in this set. And my control grid voltage is only one volt. I can't
get 3.5 no matter what I do. So if I turn the volume way up, my plate voltage goes down to 112
and the screen voltage goes up to 72, never gets to a hundred. But second IF, similar results,
similar thing going on. One volt on the control grid. The second detector,
the plate voltage is very low. And then that was an issue, but we just figured that out.
The first AF, the plate voltage is low, but the control grid is on the money.
This one they're telling me to use the 250 volts. I did use the 250 volts. Plate voltage is low
on the two output tubes and the control grid voltage is low on the two output tubes.
I'm not dead. I'm not dialed into a station really good though. If I was really in a station
where it's cooking, maybe some of these would raise. I don't know. So I'm going to look at the
schematics for a second and see if I can see if there's a dead link in the chain that's screwing
things up. I'm leaning towards it's the meter though. I do have a volt meter, a tube volt meter.
What do they call it here? High resistance DC volt meter to measure plate and grid voltages.
So we may have to redo it with that. I've got one that we did a video on one time. I'll have to pull
that out and mess with it. Yeah, maybe I'll do that first. I was thinking I could lower this,
lower these voltages with a variac and it would change this, but it could be that they're fine.
I'm using the wrong meter. Let's do that first just to rule that out. All right, I got out the old
vacuum tube volt meter and I did get some slightly different readings.
This is a big mess, but I'll try to explain it. So starting with the first detector and you know,
I didn't, the filament voltages are what they are. I was getting 137 with the digital meter.
Now I'm getting 150 on the plate volt. We'll do all the plate voltages first.
On the oscillator, I was getting 93. Now I'm getting 100. So it's still a little low. Yeah,
I should pay attention to that. I didn't think about that. Okay. The first IF, I am getting 150.
The second IF, I am getting 150. It actually goes down whenever you turn up the volume control
because it's, I don't know how that quite works. I'd have to study it a little bit.
The second detector, I cannot get anywhere near a hundred volts for the plate. I'm getting like
15. I was getting 27 before. I think it has to do with where the volume control is.
The first AF, I was getting 53. I'm getting 55. The two 45s, I was getting 201 and 202. Now I'm
getting 220. Okay. So the control grid voltage, the 45s, I was getting 40. I'm measuring 40 as
well. The first detector, I'm measuring three. The screen voltage on the first detector, instead of
15, I'm getting 4.4. And it has to do with where the volume control is. And again, up here,
it says to put the volume all the way at maximum. The problem with that is it blows yours out. So
I'm tuning it off station and stuff with that, which might've adjusted a little bit too.
The oscillator, the control grid voltage, I was getting 10. I'm getting like six,
whatever. Again, it might have to do with volume. The first IF control grid voltage,
I'm only getting like 1.8. That's another volume control thing. I'll show you that here in a
second. Screen voltage, I'm supposed to get 3.5. I'm getting like 3.9. Screen voltage, I'm supposed
to get 185. I'm getting 75 and 70. That is yet another volume control thing. If you didn't watch
the previous videos, the volume control or resistance on it is a little high. So it's
giving me some little issues, which may or may not be a problem. The second detector is a big
problem. I can't get near 100 volts on the plate. The control grid voltage, it says 14 volts.
This is the voltage across the detector bias resistor. I measured that voltage. I'm getting
35. So I'm not quite sure why that's doing that. I don't completely understand it. It could be that
tube's bad. That's what we're going to try next. I'll show you on the schematics though what's
going on. And the first AF, the control grid voltage is dead on the money. So everything's
cool. So the output is fine. So here's the, let's look at the schematics. I don't completely
understand it. You folks will probably understand it more than me, but I'll show you what I'm
running into here. So I don't know what the, I wish they would have marked some of the voltages
on the schematics, but they chose not to. These three chokes, see I've got a check mark on these
two. This one's really high. This one was like a thousand or something like that. And this little
W is like an ohms mark. It's just the really old one. Okay. This one is high, which means your
voltage right here is probably low, lower than it's supposed to be compared to some of the other
stuff that's going on. So they have a little branch coming off here that runs up here into this IF
transformer is doing its thing, which is going to be what has to do with the second IF grid.
So the second IF grid
is 3.8. So I guess it's working fine. So it's about right. It's supposed to be 3.5. It was 3.8.
Okay. And then you go through this bleeder resistor and you go into the volume control.
This is supposed to be a hundred thousand ohms. It's like 180,000 ohms or something like that.
So no matter where I put it, I'm not going to get where I'm supposed to be. I can't get it low
enough and it'll be higher than it's supposed to be. Okay. So that branch, if you see it pops
off here, the volume control, and it comes up here and it is used to lower the screen voltage
for the two IFs. And if you remember, it did say that in the schematics with the volume control,
at minimum, the IF screen voltage is reduced to about 15 volts. So on mine,
since the resistance is high, it never gets down to 15.
It gets down to like more to like 18 or 19 and it won't go all the way up to
a hundred. So what are they saying? So it'd be a hundred. I'm getting 75 is the highest it'll go.
And then this other one is lower. I'm getting 70 is the highest it'll go. And if you look at
schematics, it's adjusting this line. So my theory is the voltage is low here because of this.
So it comes out and this voltage is going to be lower. Now why it won't go down even lower,
I don't know. But this one is actually a little lower because it runs through a resistor.
I don't think those are that big of a deal. It probably doesn't matter. It's just going to
change the volume. So then once you get through the volume control resistor, which is too big,
you have this little branch, which is running off and it is the screen for the first detector.
Well, if you look at the first detector, I'm supposed to have 15 screen voltage. I can only
get like 4.4. So that might be a problem. If the first detector is not proper, you know, you're
going to get antenna issues, which we might be getting. I don't know. I haven't aligned it.
We may be able to just adjust whatever that problem is out with the antenna, with the
alignment. Yeah. All right. And then we come on from here. We go through another resistor,
the bleeder, the bleeder resistor number two, and you have a branch off here. This branch
runs over into the cathode of the first IF. Okay. The first IF,
control grid voltage is low on, I can't get it up to the 3.5 it's supposed to be. So
first IF, here's the control grid. So I wonder if that's because it's measured from the cathode
and the cathode screwed up because of the, because we've got a voltage problem here.
I don't know. I don't know what the voltage is supposed to be here. So it's kind of got me
screwed up. So we may be able to line it out, but here's what I'm going to do.
This second detector plate voltage never gets high enough and the control grid voltage seems
too high. 35 instead of 14 if you measure across the bias resistor. So we are measuring here across
this. That's what they're just using to measure it by. I wonder if that could be because this is
screwed up. So out of this plate, we're only getting 27 volts and we're supposed to get 100.
So I'm just going to simply swap this tube and see if that does anything for us. I don't even
know what we're trying to do because I haven't tried to align it yet. I'm just checking voltages,
trying to make sure everything is somewhere where it seems reasonable. This one seems way
off. So I'm going to swap a tube. And remember, I've already done the resistors. I've checked
every one of them. They're all within spec. The only reason I didn't do this is because it's part
of the choke. I can't get in there. This is a block, you know, the filter choke. So I can't
get in there and mess with that. So I'm going to try swapping this tube and see if that changes
some of those voltages around that area. And I will let you know. All right. So if you didn't
see the previous videos, I tested a whole bunch of tubes. I ordered some online and all this stuff.
My tube tester wasn't working right. I've repaired it. And you know, I've always been a proponent of
the idea that the only way to really test something is to put it in whatever it's supposed to go in
and just see how it works. So I just swapped the tube out with another one. And now I've got 68
instead of 27 out of my hundred. If I turn up the volume, that actually goes down.
And my 14 volts is 15 volts. So I think we're good. So that, I got tubes bad.
So I'm going to just tune through the channels and just see if I can notice any obvious change in
reception. Oh, when I put the tube in, I just turned it right back on and it was much louder
than it was before. It hasn't been aligned, obviously.
Yeah, it's, it's no more receptive than it was. I've run past the middle there
because there's a clear channel that's just so loud. You can't even listen to it.
Oh, you don't, he eliminated and
where that's coming from. That's about, I think 740 or something like that.
Um, okay. Um, so this, this chassis has a adjustable antenna because it's the H2
instead of the H1. Um, so I think it's this antenna trimmer here. I'll show you what it
looks like. So you can just screw with the, literally screw with the, the antenna, you know,
um, so I don't know if that affects, let's see if we mess with that.
Well, it's just going to, it's just going to add and remove resistance to the antenna, I guess,
right? This is basically shorting this out. And so it's changing the, the, the resistance
of your antenna, making it the correct length, I guess. Um, yeah. Okay. So this first detector
also seemed to kind of be a problem because, um, although the plate voltage is correct,
the screen voltage never gets high enough. So I wonder if that could be because there's
something going on with the tube. So I think what I want to do is I'm going to swap this tube out
and just measure the voltages and see if there's a difference. I'm trying to learn, right? I'm
trying to, I'm trying to learn if, if the tube being screwed up or slightly leaky or whatever
they do, if, if even though this plate voltage is right, this is low. So, you know, how will we
ever know if we don't swap it out? So I'm going to just swap it and then check the, the measurements
and see if I can learn something. All right. So I swapped it. It didn't change much. Uh,
the plate voltage lowered a little bit. So it's 138. Now it won't get to 150. When you turn it
up, the plate voltage goes down. Um, the, uh, this is what I was checking with the digital meter.
Uh, the 4.4 on the screen voltage is about the same with a different tube in. So,
you know, the only thing involved here is it's the voltage coming off the end of that volume
control resistor. Um, we are measuring it, measuring it relative to the cathode though.
Um, so it could be that the cathode is low. Let me change this so they don't strike me.
You know, if the cathode was lower than it's supposed to be, that would screw up all your
voltages. Um, so why would it be lower? Oscillator transformer. We've got this trimmer here. So the,
the trimmer would change this, which potentially could change the plate voltage.
Um, wouldn't that screw up our, uh, this voltage? I don't know. So, okay. So I'm not going to worry
about it. I think our next step is we need to align the thing, um, with those voltages in mind.
So it'd be interesting to see if we can get the thing to sound good and pick up good stations.
I also want to figure out a ground connection because this hum
is probably because there's no ground on it. I tried just plugging it into the
wall, like I mentioned, and, um, it doesn't like that. It makes the hum much louder.
Um, so I might be able to drive a freaking stake into the ground outside or something
and connect to it or connect it to a pipe or something. I don't know. I don't really have
any grounds in here. What could I, what could I do? I mean, we've got concrete. If I had a
dirt floor, I could just do it. I don't know. We'll have to figure it out. But, um, that's
where we're at. So I didn't get too much accomplished today. I've been going through
and sorting all of my tubes too. I have a ton of them. This is just my little tube tester setup
here. My RCA tube tester. I try to put RCA ones in there if I get them, but, um, this is just,
I would say, I don't know, 20% of the ones that I have, maybe 10% of the ones that I have,
but most of the ones that I have, yeah, probably 10% of what I've got, but most of the ones I have
are compactrons and stuff that aren't that useful. So you probably saw that video that I did a while
back where I picked up a ton of them. I, um, I've got some from Bob's radio shack whenever he passed
away. Um, his son sold me all of his. And so I had quite a few from that, including that's where I
got this, this tester. And, uh, then I went and picked up a whole bunch from a guy in Rock Hill
that was from an old TV repair shop. And, um, some of those have been radio ones though. So I've been
going through slowly and sorting them. I went to that, uh, radio meet, the wireless associations
swap meet, and I bought some, um, tube caddies. So I've been moving them around and putting them
in boxes and getting everything kind of organized. So I know what I've got. That's how
I was so easily able to find replacement tubes for these to go right there. Um,
cause I'm getting everything sorted. That helped me out. And plus I figured out that
one 24 isn't that great. So I'm gonna, I'm gonna crash it. Um, I got plenty of them though. So,
um, I've been spending a lot of time doing that and, uh, I really wanted to check all these
voltages before I aligned it, because if there was a serious problem where I needed to put a
dropping resistor in it or something, um, I wanted to, uh, figure that out ahead of time.
I think I'm just going to run with it. I know the filament voltages are too high,
but I'm not too overly concerned about it. Um, that's where we stand. So I hope you enjoyed
the video. Leave your comments down below. Tell me what you think about my issue here. So
this is way too high. Instead of a hundred ohms, it's like a thousand ohms, something like that.
Which theoretically would drop these voltages too low. And then this volume control resistor
is strong. It's too high too. Instead of a hundred thousand ohms, it's like 180,000 ohms,
which is going to screw up this, which just so happens to be the first detector, uh, screen
voltage. And, um, so it's at four volts. It's supposed to be a 15 volts,
but I don't think there's really a way around it. I guess you could get cutesy with it and,
you know, put a choke from here to here, but you know, they've got them in these blocks for a
reason. If I can get to this point and this point, as a matter of fact, they're right there.
So I could theoretically, nope, that won't work because this is coming from here. I would have to
go from here, here to here. So if I went from two to four, I could possibly put another resistor
across it, um, to deal with this choke being too high. Put one in parallel to get it near it,
but I, you know, I hate to do crap like that because you're not really fixing the problem.
You're just freaking modding the problem. Um, and since we've got this adjustable antenna and
everything, I don't know that that has to be perfect, especially since the plate voltage
is all right. So whatever it's doing, it's letting the juice through. So let me know
what you think about that. Let's see what they're playing now. God, they're on a commercial.
They took Rod Stewart off. Let's see if we can get the,
the country channel. No, I don't want to hear it. Maybe it's on commercial.
All right folks, that's it for tonight. I will see you next week. I'm going to be refinishing
this cabinet too. I'm not, I don't, I'm not really that good at that. I've ordered a bunch
of materials for it. It just hasn't came in yet. We're going to be doing that too. So what we've
got left is we need to align it. Need to keep our eye on the choke. It's screwed up. We need to
remember that this is a problem. And we need to align the thing.
Didn't I mention something about, I needed to check something else out because it was off too.
Something about the oscillator. Oh, to control. I'm looking at my notes here.
No, I think we're good. I think that's our only, our only deal is this first detector,
the screen voltage is screwed up. So we'll keep that in mind. And next time we'll align this
sucker. Atwater Kent has some really nice alignment instructions. We'll see if I can
follow them and then we'll see what kind of, what kind of reception we get then.
So I hope you enjoyed it. I will see you back here next time.
