We bought 101 acres of woods, so we have and will have many stumps to address. In this video, I'm using the Woodland Mills WG24 Stump Grinder to grind a pair of stumps in the middle of our perimeter trail.
The stump grinder has a 24" diameter grinding wheel containing 34 replaceable tungsten carbide teeth. Lower the 3pt to remove an inch or so of material when driving forward. On each pass, go deeper until you are a full 6" below the surface if necessary. If the bite is too much, you can notice the back of the grinder start to lean and/or the audible change of the tracker under too much load.
When looking at the back of the grinder you will notice that it rotates in a clockwise direction. When cutting, it's important to do the majority of the cutting in the 6 o'clock to 9 o'clock quadrant, with minimal cutting in the 3 o'clock to 6 o'clock quadrant. Because the cutting teeth are traveling down in the 3-6 quadrant, a lot of the cutting energy will be wasted in the downward compression of the wood fibers rather than slicing them away. Too much downward cutting will cause the grinder to bounce around.
For reference, I'm powering it with a Bad Boy 4035h tractor with a SpeeCo quick hitch attached. The WG24 is indeed quick hitch compatible.
[Applause]
[Applause]
for
[Music]
[Music]
this is the wg24 stump grinder from
Woodland Mills and I have a marketing
relationship with Woodland Mills so they
provided this grinder the stump grinder
in exchange for me to um give it some
exposure and talk about it so there you
go there's my relationship with wooden
Mills this stump grinder is PTO powered
so there's a tractor behind it right
this is powered by by a PTO off of a
tractor it is quick hitch compatible I
have a spico quick hitch on here the
tractor is a bad boy 40 35h 35 is the
horsepower so it's 35 horsepower tractor
with a 30 horsepower PTO might as well
say 30 it's 29.5 horsepower but this is
the entire setup there's a tube up here
for your manual and any tools that you
have there's a pin that goes through
here it's a locking pin now I have it up
here just chill out over here because
you don't want this pin installed while
you're using the stump grinder this is a
pivot location and with that PIN removed
it allows the back of the machine or the
back of the grinder to Pivot in this
direction if you're being too aggressive
it can pivot out and take some load off
of that cut so you don't want this to
Pivot out that's a sign that you're
being a little bit too aggressive and
you don't want to make these or any of
these uh grinding Cuts with this pin
installed so take that off on top right
here
is a chainsaw holder so you can put your
chainsaw right here put the bar through
here lock it down and take it along with
you on the trail in the woods wherever
you want to take it I've used that
several times it is super super handy
now as you can tell this looks pretty
darn dirty and that's because I just
well ground up a couple stumps but also
I have been using this for the
past month or so on and off it's it's a
good quick easy little uh uh Bast weight
that I've been using uh but also I have
been grinding stumps now normally when
it comes to machines and tools like this
I like to give First Impressions and and
show my first time using it but I I I
could not wrap my head around this thing
at first not because of H not
understanding how it operates I fully
understand how it operates it's because
while I'm on my tractor I have so much
stuff in the way and this totally
depends on what tractor setup you have
how tall you are all this stuff I'm
short my seat is as far down and forward
as possible I'm only 5' 6 I've got a a
big caution sign in the way I've got the
RS in the way I've got the quick hitch
in the way I've got a lot of stuff in my
way so I lose visibility down here and I
have to twist my head upside down and
backwards and look through a little itty
bitty window right around here so
there's just a little bit of space that
I can look down through here to see
what's going on and for me that is
completely
disorienting and everything gets gets
twisted and turned backwards and I keep
getting mixed up so for me it's a
disorientation kind of a thing the way
I'm sitting I've see a lot of people
online or or a few people online that
are much taller than me simply turn
around on their seat and have full
visibility of the flywheel there I do
not so so there's that uh you may have
seen on the first stump over there these
are two stumps right here and I just
left this wide open soz I'm going to
push it back here in just a second uh
this is the aftermath here I ground that
stump first than this one and with that
one I had a bunch of chatter and if you
have chatter or if this thing starts
bouncing around something's wrong most
of the time in my experience I found
that chatter is due to cutting material
in the wrong quadrant right so if you if
you divide this Pi this this 24in
diameter stump grinder as a pi if you
divide it into quarters right so you
have quadrant one over here two or
whatever naming system you want
basically all right it's o'clock 6:00 to
9:00 that's the quadrant that you want
to be doing the cutting not over here in
the 3:00 to 6:00 quadrant and the reason
being is if your stump is vertical right
obviously all stumps are vertical then
you have wood fibers STI sticking
straight up well if you put a if you put
a picture a stump right in front of over
here in this
quadrant then what you're doing is
you're having the teeth of the cutter
come down in into the top of the wood
fibers and that's very very hard cut
it's a very very hard cut it's very very
aggressive uh it makes the the the
fibers want to tear off and chip off
more so than if it was cut this way on
this quadrant then the slicing cut or
the sideways cut if it's right at the
bottom sideways or slicing this way
that's in the woodworking World cutting
downhill which is the direction that you
want to be cutting so you always want to
be slicing the tips off rather then
going into the tip of the fibers so no
no on this side yes on this side and
that's further evident by that little uh
debris guard over there it's going to
cut and push it up and SM smack it to
that debris guard and hopefully keep a
lot of it down uh into the uh into the
ground rather than flying all over the
place I will recommend having a rake
with you of some kind or a pitchfork or
something to pile this back into and
also get the debris out of the way in
between cuts if you're doing this by
yourself I am I wish I would have
brought a rake to keep this nice and
clean as I was cutting so I would have
better visibility but I didn't bring a
rake and now these stumps that were
right here oh that's a little itty bitty
piece of root I thought oh no did I miss
a whole bunch no that's a piece of root
from something else admittedly I I need
to get better at using this Stump
Grinder like I said for me it's a vis
it's a visibility issue so as I'm over
here I have to to twist my head around
backwards and look
down right there that's where I'm
looking at when I make my cuts so I see
the PTO shaft I see this horizontal
guard up here and then the RS right
there so I've got very little visibility
to actually see what's going on in order
for me to get right there I have to
twist around and go upside down now I
haven't tried with one of these bigger
trees like that one or say one over here
in the shade where I can talk about this
a little
better so these are much larger diameter
trees and I will be cutting off a bunch
of these using the the rest of the tree
for materials and stump grinding in the
future I haven't gotten to these just
yet because I don't want to get carried
away taking down too many tall trees uh
that I can't process without my Sawmill
and then also uh where we're going to be
clearing out some more of these is for
pasture land down the road just a few
Acres of pasture Land once we get to it
however the trail system's coming along
nicely and it's going to be a lot of fun
to be able to ride these
Trails uh without whacking into these
real tall stumps so that's it for this
video uh I will be showing the stump
grinder again on much larger trees and
much larger stumps in the future just
not quite ready for the big stuff just
yet you guys take care have a great day
and I'll talk to you in the next video