DR #9 - Hewlett Packard 35900B Chromatography Interface Unit Troubleshooting and Repair - No Power

Duality Repair
132 followers
575 Video Views·Mar 12, 2025
In this video I document the troubleshooting and repair of an HP 35900B chromatograph interface unit that doesn't power on.
hey everyone its Nick welcome back to
another duality repair video tonight I
have something a little different to
look at and repair this is a Hewlett
Packard 35 900 B model dual channel
interface and what this is is it's the
interface between a piece of analytical
testing equipment and its associated PC
and software and so most commonly the
type of piece of equipment used with
this is a gas chromatograph for instance
yeah not that it's critical to this
repair but it is very interesting a gas
chromatograph is a piece of equipment
that is used to separate out constituent
components within a sample most commonly
are most familiar ly it is used to
identify the amount of alcohol in your
blood so if you're pulled over and
you're suspected of drunk driving and
they draw your blood they're gonna use a
gas chromatograph to analyze and
determine the amount of your blood
alcohol content so it's pretty
interesting it's used in many other
applications in different industries but
that's just one that's probably the most
familiar application that a gas
chromatograph is used for so this is a
dual-channel interface it's pretty
simple front controls here really just
start and stop and then you know channel
a is for one piece of equipment and
channel B is for another piece of
equipment you can use dual mode you can
use you know use it for two pieces of
equipment at once or just one on one
mode you know one channel at a time and
basically all this does is it converts
the analog signal to a digital signal
you see the analog and digital here so
the analog signal from the piece of
equipment converts it to a digital
signal and sends it to the computer so
that they can communicate and that's
pretty much it it's pretty simple but I
bought it because I was I was pretty
curious this actually belongs or
belonged to the company that I worked
for previously and they're local here in
the Twin Cities here in Minnesota and
they were selling this on eBay for parts
and had the very familiar symptom of not
being able to power on and since this is
a you know a little bit of my history
you know I never worked on this unit but
I worked with something similar to this
at that company I thought it was
interesting and thought it'd be
interesting if I could repair it make a
video on it so
so let's dive right in let's make sure
that the symptom that they're reporting
is is accurate so I have it plugged in
and let's power it on I should get a
green LED power light here and then I
believe I should get at some sort of LED
and illumination under the status so
let's power it on and nothing I'm not
sure if there's a fan or anything in
this unit but I don't hear any fan I
didn't hear any relays nothing try one
more time nothing and there's no other
power button or anything associated with
it on the front or the back so before we
open it let's just check the fuse and
you can see how simple the back is well
we're back here so seen better days
cosmetically looks like it's been pushed
in a little bit here probably been
pushed against the back of something in
the laboratory but you have the two comm
ports for each instrument and then you
have the two comm ports to the PC to
control each instrument so pretty simple
now let's pull that fuse out and see if
that's blown and obviously if that is
I'm not just gonna replace it powered on
because they blew for a reason right so
let's let's just see it's three amp fuse
that's your guess I don't know I'm gonna
say plumb no see that that's the thick
fuse hard for you see that's intact I'll
check it with a meter later but I'm
gonna I'm gonna open it anyway it looks
to be intact
so that's nothing
no major shorts inside okay so let's
open it up looks like there's just a few
screws in the back here maybe you want
to turn the bottom nope
just too on the back and we'll get it
open alright so here it is with the
cover off obviously we have this main
control board here right on top so I'll
have to take this out to get to the
power supply didn't you able to repair
this but let's take a quick look around
at this first not too much to look at we
have our DC to DC converter over here
this ribbon cable looks like it's the
control to the front interface so all
the buttons on there and the LEDs on the
front
and our main processor looks like it's
going to be right here and we have this
protective cover over here I'm guessing
for some sort of high voltage just for
service protection there and the only
really curious thing that I saw is this
so there's a seven segment display here
and that's definitely not visible with
the cover on so that must be for some
sort of dies not diagnostic or
troubleshooting calibration something so
though that was pretty interesting I'd
be curious to see what that does if we
get this working and we can power it on
if that's actually doing something if
it's counting something and I'd be
interesting but not too much to look at
here the board looks pretty good in
pretty good shape a little bit dusty but
that's to be expected and so I'm gonna
remove this so we can get down to the
affected unit which is the power supply
hopefully it's directly under this who
knows maybe there's another board or
something underneath this I don't know
and so it looks like it won't be too
difficult to get off maybe one two three
six screws and you know removing some of
the connectors so I'll get this off and
we'll see what's underneath was able to
get that top board out pretty easily and
I'm getting closer took me a while to
figure out how the hell these boards
were mounted so again here's our power
supply right here and I was a little
worried because you can see the casing
that's here it's actually welded or
called riveted to the chassis of the
frame so I was like well shoot I can't
even get this power supply out but it's
it's it's slotted so it should come out
just like this board does I didn't screw
it from the back but then it's just
rides in these guide rails here on
either side and it slides out and so
obviously I'm almost there and that's
the power supply section having a fun
time trying to figure out how to get
this thing out it's not coming out like
that one is so I don't know I don't see
any other screws the only other two
screws whoops all right hold on the fan
huh these two for the fan I remove this
screw it's ground screw and there's any
other screws don't have to
poke around a little bit more I don't
want to pull this too hard for fear that
it's attached somewhere else I'm gonna
break it so I'll be back when I figure
out how to slide this now but we should
once they get it out we'll have access
to thee directly to this power supply
board all right I managed to get the
board out of the unit I was missing one
screw here on the side and then I just
slid out very easily like the other
board and so here it is this is a
switching power supply I did a brief
initial inspection I looked at the
capacitors none of the capacitors
surprisingly are bulged I don't see any
signs of leaking I also don't see any
other signs of burning so any sort of
burn marks or anything like that so
surprisingly nothing obvious on the
supply right off the bat now I don't
have any schematics so I find it helpful
when I don't have any sort of schematics
or diagrams when I'm working with a unit
even something as seemingly simple as a
switching power supply to draw block
diagram so that helps me kind of
compartmentalize certain parts of a
board and it also gives me certain
points of a board to check for voltages
or signals or whatever and so let's just
go through this really quickly and this
is common to pretty much all switching
power supplies and this is no exception
so let's start with ACN ACN's come in
and here through the plug right and it
goes first through the fuse which is
this fuse holder right here and we check
that that seems to be good I'll check it
with ammeter to verify but physically it
looked to be in good shape so I'm going
to go through some initial filtering and
so that's gonna be capacitors here this
giant inductor here and some more
capacitors right here before it goes to
the bridge rectifier and the bridge
rectifiers here bridge rectifier is
gonna rectify the voltage into DC pulse
DC and then again this is very generic
so obviously there's a lot more going on
than just this block diagram but this is
just what I had grown up so for the
bridge rectifier it's gonna go through
the drive transistor which is here in
this case there's only one sometimes you
have two transistors driving
and a push-pull configuration this looks
to be a single transistor configuration
so your voltage is gonna be driven
through this transistor by a drive IC
though so there's a drive I see that's
gonna turn the transistor on an offer
it's gonna it's gonna alternate the
polarity so that the the your polarity
of your voltage is going to swing up and
down to create AC through the transistor
and through the transistor are going to
go to the transformer which is here
which of course is going to transform
the voltage and we're gonna move on to
this side where we get to rectification
so looks like we have two diodes right
here for rectification and there may be
more that I'm missing but those two
definitely you can see the giant
heatsink here so we'll rectify it so
that we have DC voltage here and then
some more filtering so that's what all
these filter capacitors are and I think
I saw a few inductors an inductor there
so some more final filtering before we
get to DC out at the connector so it
kind of flows pretty well with this
block diagram from left to right on the
board as well and so as I said this
gives us having this block diagram gives
us familiar points to test we don't have
a schematic that tells us what voltages
should be where and we don't even have
although they're each components label
on the board I don't see any test points
that are labeled with what voltage
should be where and even on this
connector here it's got I don't know
maybe 15 pins and although the
connectors labeled the connector itself
is labeled there's no label of what
voltages should be where you know they
might only use two or three pins on here
for voltage I don't know they might use
all of them there might be five
different voltages and might be two I'm
not sure so we can at least walk through
this diagram and walk through the supply
and check familiar points for voltage so
the first thing I'll do is check the
fuse of the mirror and make sure it's
not open and I think the best most the
the best place to check next is the
bridge rectifier so we able to see if we
have AC voltage going in and DC coming
out that's a great place to start if we
have that we can rule out this part of
the circuit and we can move forward here
so let's start with the fuse and the
bridge rectifier obviously I'll leave it
off well I'm checking the fuse just make
sure it's got continuity there sure it
will as I said it was a beefy 3 amp fuse
and so if that thing blows it's gonna be
pretty obvious use is gonna be here
yep okay so the fuse is okay I'm gonna
leave it upside down as I plug it in I
just need to make sure I know where that
here's that bridge rectifier right here
so you see these four pins here 1 2 3 4
2 outer are always gonna be AC and the
two inner are gonna be DC so we'll check
for AC and DC on those 2 pins there are
those 4 pins I should say and then we'll
see where we're at so let me plug it in
make sure it's not powered on yeah all
right obviously if you're gonna plug in
something like this and you have exposed
parts of the circuit be very very
careful there's no really fun way to do
this unfortunately I couldn't test this
one was in the unit and I can't test any
of these components because it was all
hidden in that compartment which you
know was riveted to the unit so not much
I can do there it's gonna be very
careful hold the edge of the board as I
plug it in even though I don't have the
power on we're still gonna be well
not plugged into the socket here so here
we go plug it in there okay let's be
very careful and powered on all right no
smoke and then we've already turned it
on several times and I'm sure the
previous owner has already tried to turn
it on and off many times so all right
I'm on AC mode I suppose you should see
the meter and so we checked the fuse I
suppose we can check the fuse to check
for voltage at the fuse so we can see
the meter so I'll find a nice ground
point and we'll check here for under 20
volts AC and we have it so let's just
jump straight to the rectifier it's a
good place to go and again the two outer
pins should have 120 volts ac on it
you
that is very surprising so as you can
see I don't have any voltage on the
outer pins and let me make sure I'm
making good contact I am those should
definitely be yeah AC and then so
obviously we're not gonna get any DC out
of the center Center two pins there's no
AC present on the other two that is very
surprising so interesting I was
definitely suspecting that the front
part of the circuit would be okay it
usually is it's usually in this control
part of the circuit in the drive part
the drive part of the circuit so I guess
we're going to work backwards here let
me turn it off unplug it turn it back
over and take a closer look at that
front portion of the circuit here as I
said really and as you can see on the
block diagram here and of course in this
case it's probably not true since we're
not getting voltage there but in most
cases you want to be very careful even
after powering off of large filtering
capacitors because they're going to stay
could potentially store a lot of charge
I'm gonna even though we're not getting
voltage to this rectifier which would
prevent it from having voltage going
past it I'm gonna I'm gonna always
assume that there's voltage Gentiles
capacitors so just be cautious so let's
take a closer look here and you know
there's not that many components in this
front end here obviously I'll probably
have to go back and forth for you know
to check what what makes contact with
what so we have see really we just have
a couple of capacitors maybe eight
capacitors and this giant and dr. here
and and that's about it before we get to
this rectifier so something inside here
it's probably open I doubt it shorted
because we would probably blow the fuse
so something might be open and to check
for that I don't see any MOV here any
mobs there might be
it's a capacitor capacitor it's hard to
tell have to take closer look probably
off-camera and I'll let you know what I
find out and what we're gonna test next
but very surprising that it's in this
part of the circuit at least for now I'm
assuming this part is good this part is
definitely there's something wrong here
so let me take a closer look offline and
I'll come back and let you know why
phone alright I'm fairly confident I
found the issue or at least one issue I
inspected this front section of the
board here and I looked on the top for
again for any any evidence of the shorts
or anything leaking so there's no
electrolytic sign here so no concern
there so I inspected the back for any
issues with the traces or any leaking
coming on onto the back of the board and
I did find something so I'll zoom in
here I'm pretty sure this is our issue
or at least one of the issues so what
I'm looking at is
this right here so hopefully that comes
through okay there you go you can see a
little better you see that crack there
so this trace has lifted fairly
significantly all right and what this is
is this is one of the legs of the
inductor this giant inductor here so I'm
not surprised this is heavy this is
probably the heaviest thing on the board
and the probably also a lot of heat you
know heating and cooling here going on
over many years decades really and so it
finally caused it to to give and so of
course the only way to tell for sure is
to check for continuity and you can kind
of see it there a little bit of
discoloration that's that's the trace
being lifted and so let's check for
continuity obviously you can see the
trace itself should go from here to here
and then to here and you can see we
don't have any continuity and so this is
directly off of our this is actually the
switch right here so we have power
coming up to the switch here on either
side and this is the power switch and so
right now the switch is off right not
getting any continuity turn the switch
on and then we have power jumping across
the switch as it should and then it
should flow through the end through to
this point of the inductor and then
through the inductor well we're not even
getting to the inductor so so that is
definitely why we're not getting at
least getting voltage to the rectifier
now is that our only shoe I have no idea
but it's definitely a an issue and so
I'll have to fix that I'm not sure if if
I can repair the trace itself I think
that the best thing to do is to just
make a jumper wire from here to here a
nice beefy wire and maybe cut the trace
so that it's it's not so it's
independent and it's not saying you know
partial connection there so I think I'll
do that now I'll make a jumper wire here
and we'll verify we have continuity and
we'll turn it back on
and we'll make sure we have voltage to
the rectifier here and we might as well
check for some voltage at the outputs
here again I don't know what they're
supposed to be here at the output so
pretty accessible pins right here but we
should be getting something there's no
way we're getting voltage there right
now we're not even getting voltage to
the rectifier bridge rectifier so so
I'll make a jumper I'll power it up and
we'll see if we have any outputs here if
we do I'm gonna clean up this board
we'll get everything back installed and
we'll see if it powers up alright so as
you can see it repaired the trace there
I bypassed it with a new wire and so now
we have continuity through the switch to
the inductor and so let's power it up
and check for voltage here at that
bridge rectifier as we did before let's
plugged in it's powered on let's check
for AC voltage I believe before I
mentioned that the AC was on the outer
two pins but I was incorrect it's on the
inner two pins so let's check a CE and
the inner two pins here we should have
120 and C 120 there we go
now let's check the output DC depending
on what type of up what this is okay so
you can see the one there so this has
got a voltage doubler in there so it
it's normally straight out of a bridge
rectifier it'll be 1.4 times the input
due to the RMS value so it should be
like 160 170 volts DC this looks like
it's a doubler so this is gonna be you
know 300 and some DC out yeah there you
go
332 volts DC out okay so let's check for
some outputs I could do it here at the
these pins on the back but I don't want
to short anything it'll be a lot easier
to check the pins on the front so let's
flip it over plug it hmm make sure you
don't have anything conductive on the
bottom if you're gonna have your board
on the bottom or if you're gonna have
your board you know the bottom of the
board touching the your bench and so you
don't have any loose conductive material
strands of where it's in like that
mm-hmm
[Music]
okay there we go
and I think I get to use these for the
first time that might be too small for
these sized pins are these nice jumpers
from a banana to the you know receptacle
here let's see if it see if it works for
this and inside no these pins are too
big darn it nope I haven't got to use
these yet so to see the standard jumpers
it's okay
all right I'm filming with one over here
and I'm in the DC mode let's get the
glare out of there I'm in the twenty
twenty volts scale I don't know what
kind of output we're gonna get so let's
just check here try not be in the way
I'm gonna start from the pin furthest
away from us and move my way forward
here very promising first pin 12 volts
so 12 volts on the first pin second pin
nothing third pin 12 volts fourth pin
nothing fifth pin 5 volts five point one
volts six pin nothing seven five again
ate nothing nine five again ten nothing
eleven nothing 12 four point seven it's
interesting hope that's not an issue and
their third to last pin is 12 volts on
the dot
second one last pin is zero and her last
pin is negative 12 so we have a bunch of
positive 12 and positive five and then a
negative 12 as well I feel really good
about this I think we got the power
supply resolved I think we got it fixed
so I'm gonna put everything back
together I'll clean up the board a
little bit I'll put everything back
together and power it on and we'll see
if we fixed it okay I get it all back
together - the top cover just because I
wanted to see if it does work what that
7-segment display does if anything so
time to see if our efforts paid off it's
plugged in let's power it on
hopefully we hear a fan and we see some
lights going
there we go so I hear the fan obviously
we have the power light illuminated we
do have a fault and then so let's go to
that southern 7-segment display number
three and there was actually another
7-segment display here in the front but
yeah so I do have the operator's manual
I'm curious to see what kind of fault
that might be because I do want to fix
this completely if I can we obviously
got the power issue resolved the powers
on no problem
here the fan spinning yep it's got good
airflow back there so let me take a look
at the manual see if it's got anything
about error codes in there hopefully it
does see we can figure out what's wrong
with it I think I have everything
plugged up correctly and there's nothing
else to hook up so this fault light and
you know maybe it's because there's
nothing hooked up to it in the back I
don't know
so I'll be back after I take a look at
that manual okay so the I think as I
said earlier the service manual is very
very lacking you know not only doesn't
have schematics but it also doesn't
provide any information for the error
codes what it does say though is that at
startup you do have to have your
communication cables hooked up to your
PC and if you don't you're gonna have
that fault light remaining so I think
that's what our issue is doesn't say
anything about specific fault code so I
can't know for sure but I believe that's
the issue I have no reason to believe
that this unit wasn't working before and
it simply just stopped working because
that inductor trace eventually wore and
broke broke free and so a power failed
to the unit
and so I'm going to deem this unit
repaired and call it a success
even though we do have that fault right
remaining fault light remaining again I
believe it's due to us not having
communication cables with dev this is
after all an interface unit and so it is
checking for communication to the host
PC which we have done so I have no way
of testing this further but I'm gonna
call this repaired okay I didn't think
I'd be back but what I was seen earlier
was not normal it should not fail
regardless of if you have connectors
plugged in I found that when I was
putting this top cover on that I had two
extra screws so I pulled it apart I
pulled this front faceplate off and
there was a connector right here that
connects the top border to the bottom
board and there are two screws holding
that in place so basically I didn't have
that seated all the way and so now I
attached those two screws my power it up
you can see watch the 7-segment display
it gets to one gets the two before it
would beep when it gets to three and now
it gets to three and four just fine and
it continues on so this is the self-test
and you can see it's it's p4 pass and
then now we just get these blinking
lights here and the fault light goes
away and the blinking lights just
indicate that we don't have any
communication
obviously these anything hooked up so
now it is absolutely fixed I feel a
hundred percent confident that this
thing will work I'm glad I well I guess
I would have figured out eventually
since the screws weren't I had extra
screws but I'm glad I was able to get
100% resolved so again thanks for
watching we'll see you next time
you
