DR #6 - Line 6 LD150 Guitar Amplifier Troubleshooting and Repair

Duality Repair
132 followers
656 Video Views·Mar 12, 2025
In this video, I document the troubleshooting and repair of a Line 6 LD150 bass guitar amplifier with no output.
everyone its Nick welcome back to
another duality repair video in front of
me tonight I have a line 6ld 150 it's a
150 watt bass guitar amplifier very neat
so the gentleman who dropped this off
said that the symptom was low output so
low volume and the nice thing about this
unit is that you don't need a bass
guitar to test it so if you're someone
like me someone who does not have a bass
guitar you can simply plug in a 3.5
millimeter phone plug into the jack in
the back and hook that up to your mp3
player your computer or whatever you
want whatever music you want in there so
that's what I have right now I actually
have it hooked up to my computer and I
have it hooked up to a 432 Hertz tone I
thought it would be simple easy to easy
to hear and distinguish between any
other music or something like that if
it's jumbled so let's turn it on and see
if we get an output and if we do if it's
low or what I'm gonna turn it on right
now so we did have a tone I'm sure you
could hear that I was on for maybe two
seconds and then it shut off we have
lights so there's still power let me
power cycle it again off same thing
interesting
so I believe when it's plugged in to the
you know that's definitely that's the
case when you have an mp3 input plugged
in the master volume is no longer in
control this is this is all the way down
the your source volume is what's
controlling the volume so I'm gonna turn
the volume down on the source very low
that's as low as it goes right there I'm
gonna power cycle let's see if the
volume changed they're turning it back
on
did sound quieter I'm gonna turn the
volume up now see if it gets louder so
it's responding to volume commands at
least through the mp3 input it does have
input but for some reason it it's
shutting down hmm maybe some sort of
protection certainly sounds ok let me
show you how I was able to remove the
control assembly oh it's very simple
very appreciative of the engineers at
line six for making this so easy to
remove not all units are are so easy to
work on so to get it out you have six
screws one on each corner of the top of
the cabinet and then one on either side
of the handle pull the handle off pull
all six screws out and then you slide it
out from the front so push it from the
back slide it out you want to slide it
out maybe three to four inches and then
you have to disconnect the cable the
speaker here on the left and then
carefully slide it out the only thing
that's going to run into is that speaker
wire so kind of keep that speaker wire
flat on the bottom so that you don't
drag anything over it and try and cut it
and then the whole thing just slides out
I'd also be careful you can see how this
bottom is exposed when you're pulling it
out
try not to reach your fingers too deep
into the bottom where you might touch
something with some voltage on it like a
capacitor most things are
not really exposed you do have some
potentiometers so I'm not sure what kind
of voltages around there just be
cautious then you just slide the power
cord out through the front and then
you're out that's it there's a speaker
cable there that's the only thing that
really can trip you up so there's even a
note on the top very nice of them you
can see it there it says stop here
the line all the way across so prevents
you from pulling this control assembly
all the way out and then potentially
ripping the cord to the speaker pretty
simple I only can take a look at this
entire module if you find anything
here's the control assembly removed from
the cabinet it's upside-down and
forward-facing so I have the control in
the front here with all of the knobs
main input power coming in from the back
so I guess we'll walk through this
pretty quickly mains power comes into
this power board here via this connector
and this connector goes through a fuse a
couple of capacitors where it comes back
out through this connector to the
transformer presumably step-down and
then comes back to the power board
through this connector it's then
rectified with a full wave bridge
rectifier here in the back goes through
a bunch of filtering capacitors here the
main filter caps your output filter caps
before it's out put it to the front
board via these blue cables and then the
audio output board via the white cables
audio input so we have two on the front
a passive and active input so that's
where you gonna plug your guitar into
for me I'm plugging it into the back
here I'm not gonna flip it around
because it is plugged in it's not
powered on but it's plugged in the mp3
input is on this top board here and that
audio signal comes to the front board
via one of these gray cables one of
these smaller gray cables passes through
the front board passes through
the blue cables to the Power Board and
then finally passes into the audio
output board before passing out to the
speaker via this connector here which
obviously is disconnected first things
first is a visual inspection sometimes
you get lucky and an issue becomes
apparent after just a visual inspection
you hardly need to use any sort of meter
to to find the problem
I've done a little bit of an inspection
already power board fuses okay I don't
see any signs of burning or overheating
all of the capacitors look to be in good
order they're not raised no leakage
coming out of their vent tops the audio
put board all those capacitors look to
be in good order as well not raised no
leakage out of the bottom or top out of
the vent and then the front board I
didn't see any signs of overheating and
those capacitors look to be in good
order as well so passes the visual
inspection I'll go on to checking
voltages next I don't have a schematic
or a service manual but these boards
seem to have the voltages printed on
them pretty well so I should be able to
determine what the voltages should be
and where so let's start with the mains
input I know I have power getting to the
front board because the lights turn on
and we do get an audio output for a
second or two so I'm just gonna check
power through the holes unit here so
I'll power it on I'm in AC excuse me now
I'm in AC there's a ground pin over here
on the left that I'll use for my main
ground slide this over so you can see a
little bit better we'll just follow the
power through the unit a little bit so
I'll start at the fuse I know I'm gonna
have 120 approx volts there of AC yes I
do 121 it's gonna make it through the
fuse obviously fuses okay that's gonna
come out again out of this connector to
my transformer so we can check there 120
volts there
to the transformer transformer is going
to drop the voltage down and come here
of course I can't use the ground pin as
a reference anymore so this one's got
several windings on it not sure what the
voltages are gonna be so we have 70
coming from pin one to pin 226 coming
from one two three
I'm thirty five and a half from one to
four so there's no labels on that
connector I'm going to assume this
transformer is in good order it looks to
be in really good order for a
transformer to be faulty is very rare so
I'm going to assume that this is working
properly so again all of these voltages
will be rectified through the rectifier
and filtered through all these
capacitors where they'll come into this
board and this board so there are
voltage labels on this right next to
this connector here as well as this
connector so I'm gonna check here this
seems to be an easier point to check so
I'm gonna go to DC since it is rectified
I must turn the 200 volt DC range and
sorry about that you can't see but I'm
gonna tell you how these are labeled so
I'm gonna call this pin on the right
here pin 1 can't stop that movement
there it's tough it's pin on the right
here is pin 1 and it's an 8-pin
connector so the pin on the left I'm
gonna call pin 8 again that's just what
I'm calling it so pin 1 is labeled vs
positive vs so V supply pin 2 is labeled
ground pin 3 is labeled - vs pin 4 is
mute pin 5 is -16 looks like a V but I
think it's u so that might be for the a
controller Drive
and you have audio ground
it's pin six audio positive it's pin 7
and audio - is pin eight so I'm not
gonna worry about pin six seven and
eight because I don't have any audio in
there and I'm not gonna I don't want any
audio hooked up right now without a
speaker hooked up so I'm gonna start
with pin 1 and pin 3 that's supposed to
be pin 1 should be plus vs so we'll see
what that comes out as what my black
probe on my ground pin just for polarity
reasons vs is tough to get a good
connection there about 50 volts DC that
should make B - - 50 volts if I can get
a good connection on there yep
okay so again of course they're not
labeled with the voltage just positive
vs minus V s so those seem like
reasonable voltages for me and they are
equal one thing I just noticed this
thing has a fan back here - cool
this heatsink which is attached to these
looks like driver driver chips here and
the fans not on and if I spin it it does
spin freely so I doubt the fans bad I
would think that this thing should be on
no matter what unless it's temperature
regulated which is possible it's
possible but I would bet that that fan
needs to be on so it looks like it's got
a little connector here it's tough tough
for you to see in the camera but I'm
gonna check output to that fan because
I'm curious I'm not getting voltage to
the fan where else am I not getting it
that's not going to be in the 200 volt
range
take a look here I can actually see a
label on the board that says 12 volts
fan so on one of these two pens between
ground and that pin should be 12 volts
DC so let's see this is the red pen - 13
volts interesting and blue pen - 15
volts that doesn't seem right
interesting so right away I'm suspecting
a possible voltage issue another thing
I'm curious about when I powered on and
it in the audio outputs for a second or
two and then kicks out I was thinking
maybe some sort of protection kicking in
and so why you would need that would
potentially be voltage keep bumping the
camera DC voltage on the speakers so if
I look at this speaker connector I know
you can't see it it looks like it's
gonna be these two pins right here so
this first pin and the second pin those
are my outputs to my speaker so I'm just
gonna see if there's any sort of voltage
on those two pins so I'm gonna check pin
1 to pin 2 huh
it looked to be a bit of voltage on
there it is dropping so it's not a
constant output but that's interesting
so there was maybe 15 volts on there DC
I'm gonna power it off obviously there
should be nothing there now see there's
still residual DC voltage
let me power back on
Wow that max the 20 20 volt range for a
second it does drop but I'm gonna turn
it on and then turn it off and then see
if there's voltage there yeah 20 volts
DC on the speaker output just from
powering it on and then even powering
off its it remains that might be our
issue all right after a little bit of
checking I'm no longer concerned with DC
voltage on the output and I'll show you
what I mean so right now I have the
speaker hooked up I have my oscilloscope
probe hooked up to the output to the
speaker and I have a sine wave coming
into the unit
so I'm gonna power the unit on you can
see the where the unit is that right now
the voltage when it's off so you'll see
in here the sine wave as it comes on for
a second or two and then watch what
happens to this line as I shut it off so
it doesn't move right now I'll shut it
off so the units still on if there's any
DC voltage present it'd be right there
and then when I turn it off it would
shift I turned it off there's no shift
so I'm not concerned about DC on the
output I'm actually not concerned with
that audio output board at all anymore I
believe the problem is coming from the
meeting pin
more specifically the muting circuit so
I will cut back to the control assembly
I'm sorry I'm talking about all right so
I have the unit disconnect from the
speaker as well as the audio input
removed and so I'm gonna put my probe on
the mute pin and I have my meter in DC
volts watch what happens when I turn it
on spikes 220 for about a second and
then drops back down to zero so this
coincides exactly with the output when
that muting pin is high as in in this
case 20 volts the output is enabled if
you get sound when it drops to zero
it's disabled and so the muting pin is
driven to this both of these amplifiers
I pulled up the data sheets on these
they're muting pins they will enable or
disable the output of the amplifier how
it works is if the muting pin voltage is
greater than 1.5 volts the output is
enabled if the muting pin voltage is
less than 1.5 volts the output is
disabled so that's why our output is
being disabled that voltage that muting
pin voltage is dropping below 1.5 volts
specifically it's going to 0 volts so
that muting pin is goes through the
white wires goes across the power board
through the blue wires and it is sourced
from this main board so for some reason
this main board is disabling that muting
pin it's dropping that voltage from 20
to 0 which is disables our output
thankfully very very thankfully I was
able to find a service manual online
which included schematics so here's one
of the schematics for the main board and
you'll see I have some of it highlighted
here this is the power failed detect
circuit and so you'll see I have the
yellow and pink highlighted yellow is
the amp mute current flow path in
standard form so when the output is
enabled and the pink is when the output
is disabled or when the system is muted
so how this works and it actually kind
of tells you right here so a q1 which is
this diode right here it's actually an
adjustable shunt regulator q1 turns off
when 3.3 volts is less than 3.0 5 volts
plus or minus 1.4 percent so this
regulator has an input of 3.3 volts goes
across this resistor R 34 and the
reference voltage right here is measured
and so if this input voltage is below
nominal
this will not conduct so what this does
is normally when this conducts you'll
get this 16u voltage
it'll conduct through this transistor
here obviously through Q 1 and then Q 1
will conduct through Q 2 and then Q 2
will conduct through Q 3 and then out
here so you'll get this 16u voltage
whatever that is which in this case it
seems to be around 20 volts that will be
what your amp mute voltages if this
input voltage is too low or there's a
problem with this initial part of the
circuit Q 1 will not conduct therefore Q
2 will not conduct therefore Q 3 will
not conduct and your mute pin will be
pulled to ground via r125 and that's
what it says here Q 1 turns off Q 2
turns off Q 3 turns off and our 125
pulls the mute low so thanks to check I
wrote them down number 1 I have to check
incoming 3.3 voltage and I'm gonna check
it at R 34 I want to check it at the
input of our 34 and make sure it's 3.3
if it's too low that's our issue that's
not the issue I'm gonna check our 34
itself
make sure there's no problem there make
sure it's not open make sure it's as its
labeled 4.7 5 K next I'm gonna check our
124 that's down here so this is off
that's going to affect our reference
voltage and that will affect the working
of Q 1 as well so I'm going to check
that
I'm gonna check C 32 that's this over
here if this is shorted for some reason
that could definitely cause an issue and
then I'm gonna check you 1 itself to
make sure that's not short it well I'm
gonna have any other issues so this is
where I'm gonna start is looking at this
power failed to text circuit it took me
quite a long time to figure out where
all of these components were on the
board because they were on the back so I
had to remove the board and all of the
components on this power fail detect
circuit we're on the back so I tested
the 3.3 volts coming in at our 34 here
and it was 3.29 so I know my input 3.3
volts was good so this power fails
circuit unless there was an issue with
one of the components was not the reason
why the system was muting so I checked
all of the components
I checked the resistor of values and I
made sure they weren't shorted or open
and I checked all the transistors make
sure they had the appropriate voltage
drop and they weren't shorted as well
all those components checked out so
that's not the issue I did find the
issue the issue was with the other part
of the immune circuit so again our mute
is over here on the right and you'll see
this one leg goes down to the power fail
detect the other leg comes up and comes
over to the DSP digital signal
processing chip so if you look at pin 95
here you'll see a line coming out that's
connected to the DSP mute and if you're
reading there you're probably already
reading ahead that's okay
but the DSP chip itself can enable the
mute or disable the audio output as well
as well as this power failed attack so
that's what's happening
I checked 3.3 volts or excuse me I check
for voltage at this resistor here and it
was getting 3.3 volts what that's doing
is it's turning on this transistor which
is allowing this positive 16 u which is
actually 24 volts to flow through the
transistor which is pulling this pin to
ground so that's what's happening the
DSP for some reason is outputting the
mute signal it's outputting 3.3 volts to
enable the mute or disabled to audio now
I wasn't sure why the DSP would be doing
that looked at the service manual was
that the tuner when you have the tuner
enabled which is just a button on the
front the volume button is muted during
tuning so what I think half is happening
is either the DSP is corrupt in some way
or it's just thinking that the tuned
button or the tuned circuit is enabled
the whole time which is obviously not
the case I verified the tuned button is
working so I have the unit powered on
this is exactly what it looks like when
it's powered up I pressed the tuner
button here the tuned LED illuminates
and these two other buttons has two
other LEDs and this one cannot see this
one over here too so right now these are
active these signals are active these
channels and when the tuner circuit is
active these are disabled so this
circuit seems to be working correctly
you can actually see the smart effects
disabled as well so I don't think that's
the problem I don't think tuner button
is the problem I think there's something
wrong with their genius speech chip so
what I did was I removed R 120 which is
right here I taped it to the sheet here
just so I don't lose it and what that's
doing is preventing the 3.3 volts from
coming across the circuit and enabling
this transistor which is keeping my mute
pin high instead of pointing it to
ground that's what should happen anyway
so I haven't tested it yet I believe
it's going to work normally I don't like
doing workarounds like this it's kind of
like removing or disabling an interlock
on a piece of equipment is usually there
for safety there protect the user or the
piece of equipment itself
in this case I don't think there is any
risk to the to the amp simply because
all all that's this is gonna do is gonna
prevent the output from muting when the
tuner circuits active so this normally
would mute the amp I'll have to tell the
owner that it's not going to do that so
just to disable the audio or you know
turn the volume down when you have a
tuner active everything else is gonna
work it's doing nothing to this power
fail detect circuit it's not touching
that so if we have low incoming voltage
this power fail detects arc is still
going to work it's still gonna pull a
mute low and it's still going to drop
the audio output so I'm not too
concerned with removing this resistor
I'm going to test this for a
considerable amount of time to make sure
nothing's overheating and that it works
properly that is of course if it does
work I think it will let's check it out
so I have it on obviously I have audio
hooked up and I'm gonna press play let's
see if it works
[Music]
I'm very happy I love it there we go I'm
gonna turn that down I'll turn up just
to see if I can handle a
[Music]
right there
[Music]
[Applause]
[Music]
all right
turn that off to avoid any sort of
copyright issue so this thing is fixed
it was a little bit of a workaround but
I don't think you know I think the only
other option would be to replace a
reprogram that DSP chip and I don't have
the capability of doing either of those
I don't have a DSP chip I don't have the
capability of reprogramming that one so
I'm gonna call this thing fixed it's
working I'm gonna test it like I said
for a considerable amount of time but it
is working so that's it thanks for
watching we'll see you on the next one
you
