DR #62 - Massive Amp Stuck in Standby - Parasound HCA 2205A Repair

Duality Repair
132 followers
693 Video Views·Apr 20, 2025
In this video, I walk through my troubleshooting process to bring this Parasound HCA 2205A amplifier back to normal operation. It was a struggle, but through struggle comes growth, and eventual success!
this absolute monster is the Parasound
HCA 2205A high current power amplifier
It has five channels each at 220 watts
and it weighs around 85 lbs And this has
a problem Let's take a
look With the amplifier connected to
main power the AC line LEDs are
illuminated I'll power it
on Now we have the standby and
individual channel LEDs
After about 5 seconds the standby LEDs
should extinguish and we should see
normal LEDs up here illuminated We
should also hear the click of each
channel's relay as the unit comes out of
protection but that never happens So
this amplifier is stuck in standby mode
Let's figure out
why Let's go over the internal layout
before we start In the front we have the
giant toridal transformer In the back
right we have the input board and the
back left is the output board In the
front out of view is the front panel LED
display Back here is the protection
board Directly underneath this is the
power supply board And along the outside
mounted to the heat sinks are the
individual amplifier
boards So where to
begin i believe our issue is going to
stem from something on the protection
board And so I printed the relevant
section of the protection schematic The
reason why we're stuck in standby is
because this transistor Q90 is off If
this were on we'd have a path to ground
through the transistor to not only our
five relays but also our normal LEDs And
so we really just need to figure out why
this transistor is off I'd marked four
critical points on the schematic for us
to take voltage measurements at And I've
also placed some theoretical ranges for
what these voltages should be based on
where they're at in the schematic And I
think measuring these four points will
give us all the information we need to
make a decision So let's take some
measurements compare the actual to the
theoretical and see if we learn
anything Here's
0.1 The junction between R 163 and the
base of Q90 is about 80
molts
Here's point 2 the base of
Q71 about 195
molts This is 3 the junction between
R127 and our Xener diode D42 It's about
1.6
volts And point 4 the supply side of
R127 about 22 1/2 volts
So what do these measurements tell us
well 0.1 the base of our Q90 transistor
measured at just 80 molts This is
nowhere near the voltage needed to turn
the transistor on This makes sense We
already knew this transistor had to be
off So let's keep moving
backwards What turns this transistor on
is Q71 When this transistor is on our
Q90 is on which is why I chose 2 as
another measurement point Point 2
measured at only.19 volts Again nowhere
near the voltage needed to turn this
transistor on Still making sense so far
So let's move backwards Now we'll jump
across this 4.7 volt
xener to.3 3 measured at just 1.6 volts
This is definitely not enough voltage to
drop across the 4.7 volt xener as well
as turn our Q71 on But is there a
problem in this section of the circuit
or is it simply because we don't have
the supply voltage that's why I chose 04
as a measurement point This is our
supply side 04 measured at 22.5 volts
And that is definitely sufficient to
drive this circuit So I believe there's
a problem in this section of the circuit
We have 22.5 volts here only 1.6 volts
here My money is going to be on this
capacitor right here C93 This is an
electrolytic capacitor and I'm guessing
it turned at least partially into a
resistor So now my plan is to remove the
protection board I'll remove this
capacitor and we'll take some
measurements of
that Looks like someone's been in here
before me The bridge rectifier or four
individual diodes have been replaced as
well as an electrolytic capacitor
here
Here is our suspect capacitor It's a 100
microfarad at 25V bipolar electrolytic
capacitor The schematic actually calls
for C93 to be 47 microfarad at 25 volts
And that happens to be what I have on
hand So that's what I'll be replacing
this with But let's check the
capacitance of this one
somewhere around 87
microfarads Now technically that's in
spec for a 100 microfarad capacitor
Usually it's plus or minus 20% But it
being on the low end that's not a good
sign And even more concerning is the ESR
or equivalent series resistance of this
capacitor is around 98 ohms Absolutely
terrible A capacitor like this should
have an ESR of an ohm or less So that's
not going to work Let's replace it and
see if that
helps All right Is that going to do it
we'll see
It's not all right Well more
troubleshooting to be done then Let's
move
on Even though it was measuring bad
replacing C93 had no impact on our
standby issue So what about our 4.7 volt
Xener D42 or the drive transistor
Q71 i pulled both of those for testing
They're set up exactly how they are in
the parasound on this breadboard with
the exception of this LED This is in
series with the drive transistor Q71
such that if this transistor turns on
the LED will illuminate So I'll apply
power to the circuit
now And you can see as the capacitor
charges up the transistor turns on and
the LED does illuminate So very likely
our Xener and our drive transistor are
just fine We need to keep
moving We've ruled out capacitor C93
Xener diode D42 drive transistor Q71
I've also verified all of these
resistors are 127 162 163 and 164 are
all measuring what they should be So
what does that leave us well the part of
the circuit that I've neglected so far
the protection circuit So what's going
on after this diode and beyond i
measured the voltage here with a
multimeter and got an interesting result
So I connected it to a scope and take a
look at
this Doesn't show up great due to the
frequency but we do have significant AC
voltage there This is 5 volts per
division So this is greater than 15
volts of AC at that diode That does not
seem right So let's take a look at this
side of the circuit and see what might
be going on here Here's the diode in
question If we follow that
up see it leads to this point right here
And this comes from one of our incoming
AC
lines It's rectified just by a single
diode D31 And then it should be smoothed
by this capacitor here C88 before coming
back to our standby circuit So now I'm
starting to wonder if C88 has a problem
It's not able to smooth properly So
let's remove this capacitor and take
some
measurements All right let's make some
comparisons Here's the original
capacitor 10 microfarad at 50 volt
bipolar And here's a brand new one the
one I'll use to replace this one
assuming it's bad We'll start with the
new
one This is reading about 10.4
microfarad just fine Let's take a look
at the original
133
nanofarads not even 10% of what it
should be So this original capacitor is
absolutely bad Let's replace it with
this one and see if that gets rid of our
standby
issue The first attempt was a swing and
a miss which is okay Let's see if I got
it this time
Wow we got it That was quick That was
about two seconds or so I heard the
relays
engage Our standby LEDs extinguished and
our normal LEDs
illuminated That was
it So how does our failed capacitor C88
cause this problem well the whole
function of this capacitor is to smooth
out the halfwave rectified voltage
produced by diode D31
This should maintain a stable DC voltage
on this side of the diode and it must be
greater than the voltage on this side of
the diode so that the diode does not
conduct Because this capacitor failed we
had AC voltage on this side of the diode
And there was a significant amount of
time where the voltage on this side of
the diode was lower than the voltage on
this side of the diode During that time
this diode would conduct lowering our
voltage at this point preventing our
standby circuit from working
properly That's the end of the standby
repair story for this Parasound HCA
2205A but I doubt that's the end of the
story for this amp in general Do any of
the five amplifier boards work are there
any other problems what other work needs
to be done we'll find out Thanks for
watching
