DR #60 - The Guts of a Sansui AU-717 - Rebuilding the Power Supply

Duality Repair
132 followers
709 Video Views·Apr 11, 2025
In this video, I restore the power supply PCB of a Sansui AU-717 integrated amplifier.
this is a very pretty Sansui
AU717 unfortunately the volume
potentiometer on this unit is broken not
only does it rotate freely with no end
stop but it also fails to pass the left
channel the left channel comes in but it
never leaves after looking at some
threads online turns out that this
potentiometer is a relatively common
failure mode with this model and finding
replacements is practically impossible
fortunately we can still use this as an
amplifier so my plan is to rebuild the
power supply which is all original as
well as both amplifier modules which are
also all original and then test let's
take a peek inside before we get started
each channel has its own transformer as
well as its own pair of bulk
capacitors this is the power supply
board and these are the individual
amplifier modules i'm going to start
with the power supply so let's figure
out how to get this out of the unit i'll
be starting from the top of the
amplifier and we have three cable sets
to remove here here and here fortunately
the left and right sets don't need to be
marked in any way as long as you take a
good photo of each the center set does
need to be marked though the two reds do
not go together neither do the two
whites you can see I've distinguished
them by drawing a little black line on
each i'm going to start desoldering
i've disconnected all three cable sets
from the top let's see what we have to
do on the
bottom on the bottom some of the wires
have connectors those will just slide
right off but there are still many wires
that need to be desoldered fortunately
down here all of these wire colors seem
to be distinct so as long as you take
good photos you shouldn't need to worry
about
reassembly
here's the power supply let's see what
kind of work we might want to do while
it's out at a minimum all of the
electrolytics are going to be replaced
there are a bunch of these and yes most
of them probably still are good
especially the bigger ones but if you
want this unit to last another 30 40 50
years it's a good idea to replace those
so those are on order the relay looks to
be in pretty good condition i know that
it still does work but this is the
original the contacts can become
corroded and pitted over time and I
don't know if I can service this very
easily so I'm just going to replace that
as well i happen to have a good
replacement
here i'll also pull all four of these
transistors that are mounted to the heat
sinks clean and reapply new thermal
compound and there is a bit of a problem
on this board let's zoom in
all of these larger capacitors were
glued down to the board for support
which is fine except over time the glue
starts to eat away at whatever it
touches take a look at that Xener diode
both legs are almost fully corroded as
soon as that corrosion hits the actual
component it's going to fail similar
over here that resistor the resistor
below it there's a few other
components and the same goes for the
other side we have some
components starting to be eaten away at
and I did think this was all original
but it looks like this Xener was
replaced at one point just a single
component interesting so I'm going to
replace anything that has corrosion on
its legs including a few resistors on
either side both of those Xeners and
anything else that I might find
if you use this specific relay as a
replacement you will have to clip these
two legs they're not needed and there's
no holes on the board for those
i removed the five capacitors that were
glued down in this area let's zoom in
and take a closer look at the
damage plenty of components right on the
edge of failure
looks like these two resistors are the
closest so I'm going to remove all of
these affected components remove the
glue and then we can install the new
components i'm sure there are other
effective methods out there
what works for me is I like to heat heat
up the glue a little
bit with my heat gun and then carefully
scrape it away with something like a
flaad screwdriver takes time but it's
pretty
effective well that was a lot of work
but there's no shortcut folks all the
glue has been removed i'll do the same
thing to this left side and then I can
install the new capacitors resistors and
diodes here's the final
product a note on potential improvements
these four capacitors 23 24 25 and 26
these are the smoothing capacitors for
the plus and minus 33 volt rail for each
channel the originals were 100
microfarad at 35 volts and that 35V
rating is just too close to the 33 volts
it's trying to smooth so I'd recommend
improving those to 50 volts all right
let's get this installed and test
all right it's the moment of truth i'll
power it on and we'll make sure it comes
out of
protection sure does fantastic
let's verify the voltages of this power
supply we'll start with the low voltage
rails according to the schematic
something like plus or minus 33 volts
they're not going to be exact this one
is minus
34 and this one's plus 34.4 those are
okay let's check the other
channel over here we
have +
35 and minus
34.2 those are just fine let's move on
to the high voltage
rails and the schematic says these
should be somewhere around plus or minus
56
volts -
57 + 57 let's move to the other side
over here we
have -
57.3 and plus
57.2 fantastic
and that'll do it for the power supply
for the Sansui
AU77 i think it turned out really nice
join me next time where we'll take a
look at both amplifier boards and bring
those up to speed as well i've also
spent a bit of time analyzing the power
supply schematic for this unit and if
there's any interest let me know in the
comments and maybe I'll make a separate
video on that thanks for watching
