DR #16 - Yamaha P2075 Amplifier Troubleshooting and Repair - No Output

Duality Repair
132 followers
2 Video Views·Mar 12, 2025
In this video, I document the troubleshooting and repair of a Yamaha P2075 power amplifier with no output.
hey everyone welcome back to duality
repair tonight I have another power
amplifier to look at this is a yamaha p
2075 it's a 50 watt dual channel power
amplifier and it's got a problem so
let's power it on see the protection and
power lights both come on and after a
few seconds the protection light goes
out and you can hear that relay click
and as always I have a both of the
outputs hooked up to my dummy resistors
and I have my scope hooked up to those
resistors so we can monitor the output
so let's just go to the scope alright
here we are at the scope i have channel
a output to channel a input and channel
B output to channel B input and so let
me turn off the volume on both see if we
get anything so here's channel a that's
halfway
that's max we're getting nothing and I
have a 2 kilohertz sine wave going in
channel B turning it up half way nothing
full nothing absolutely nothing on the
output so there is a problem indeed
let's go ahead and take the cover off
and take a look inside okay here we are
inside the unit pretty simple design
obviously it's basically a 1 board
design minus the volume control board
here on the bottom and let's just go
through it really quick I immediately
see three items of concern number one is
right at the input power you can see
there's electrical tape covering these
input wires so that means somebody's
been in here before who knows what
happened in addition to them you know
probably having to rework these wires
but let's follow that the signals
through here so we have our power coming
in over here it's gonna trace through
these two wires here to our main
transformer transformer is going to
output through these two red and black
wires bridge rectifier filter caps and
then all of our power is going to be
dispersed from there our voltages you
can see another small bridge rectifier
here which is going to create another
smaller voltage for the rest of the
board and then I do have a fuse here I
checked it it is good so that's good
so first item of concern was these
reworked wires over here second item
maybe you've already seen at least two
capacitors
so I know that there's glue around all
of these you can see if you look right
here you can see some discoloration
around the cut the capacitors here as
well and no doubt there's glue around
these but you can also see the the brown
brownish discoloration on those so I'm
guessing one or both of those has leaked
out so that is a primary area of concern
but then number one for me and it's
definitely not obvious because there's
nothing visible about it what is this so
this is a dual channel integrated audio
amplifier and I saw this thing before I
even open the cover I can see it through
the vent holes and the grate on the top
cover and it looks identical to an
integrated amplifier that I had to
replace on an old Sony receiver and the
reason why it's such a pain at least for
me it was was because they they don't
make these anymore and I had to find one
on eBay and it was just a pain and
immediately I'm expecting this and
suspecting that and that's actually the
first thing about tests I already
printed out the datasheet for it let's
take a look so looks like there's 15
pins we have a left channel on the left
and right channel on the right with our
power inputs in the middle and so really
I'm just going to probe the input versus
the output and I'm I'm kind of hoping
that we don't even have an input so that
this you know I can rule this out as an
issue and there's something else
prior to this but what I'm thinking is
that we're gonna have an input and we're
not gonna have an output on both
channels so that's gonna be very easy to
test we're gonna go back to the scope
I'm going to keep my setup the way it is
and I'll just probe one channel at a
time really if I probe one channel it's
probably gonna be the same result on the
other but I'll probably both likely so
let's go ahead and go back to the scope
okay I have everything hooked up I have
the input to the left channel on the top
and the output on the right from that
integrated circuit so I'm go ahead and
power it up and we'll see if we get
anything on either channel
here the relay click and I do have my
signal going in so I have nothing I have
nothing on the input to the integrated
circuit nothing on the output so that's
actually a relief that looks like that
something is going wrong before that
integrated circuit that doesn't
necessarily mean it's good but it it may
mean that it's okay so I'm gonna go
ahead and just check the right channel
just to be sure I'm powered off while I
do that I'm sure anything even that was
the left channel
let's check the right channel it's gonna
check the input since basically we know
the outputs dead inputs going to be 14
let's go ahead and check that pin all
right so I'm hooked up to 14 for channel
a poet up here nothing
awesome good so now we'll go ahead and
take a look at the schematic and see
what comes before this amplifier to see
what went wrong maybe it's just so two
capacitors that will be simple okay
folks so this schematic is four pages
long I'm just going to show you the
input page because this is where I'm
going to start probing and if necessary
I'll show you two subsequent pages but
so let's take a look obviously we have
two channels channel be on the bottom
channel a on the top since are identical
let's just start with looking at channel
a so our input comes in through the XLR
connector on the Left we're gonna go
through this jumper go through a series
of resistors diodes capacitors more
resistors will hit our first operational
amplifier before we reach our volume
adjustment knob so what I did off-camera
was I noticed that the signal LED on the
volume adjustment knob was not
illuminating and so that means either
the LED is dead or the signals not even
reaching this volume so I probed this
connection here and I'm volume knob and
there is no signal there so that was
pretty quick we know our signal is
getting lost somewhere back here and
since our signal just goes through this
jumper really really we're just gonna
get lost somewhere in here so what I'm
gonna do is start probing backwards I'm
gonna take a look at our 109 and I'll
move my way back through the op-amp
through these capacitors to the resistor
until we until we reach a signal so I
know we're gonna have a signal here at
this jumper and basically at this
resistor and I know we do not have a
signal at the output of this resistor R
109 so let's find out where we're losing
it so let me start by probably NAR 109
alright just as a sanity check let's go
ahead and probe the input at the XLR
connector there's our signal looks fine
so here we go let's start backwards at R
109 here's one side of our 109 nothing
here's another nothing okay let's keep
moving back so we know we have no output
from our op-amp IC 101
that's pin seven we should have an input
well yeah let's see if we have an input
at pin six on the probe that
aha well it looks like crap but just my
scope not able the trigger I'm gonna do
another video eventually on recapping my
entire scope because I don't think it's
ever been done here's the input to the
op amp IC 101 we have an input so that
was fast
ic 101 is either dead or it's not
supplying it doesn't have its supply
voltage plus and minus 15 volts one of
those two things easy to check let's go
ahead and rule out voltage I'll go ahead
and get my meter out and we'll check for
plus and minus fifteen on pins well it's
tough to see two and four something like
that
I can just probe all the pins I should
have plus and minus fifteen between
ground and two of those you see that a
little bit sorry about that you can see
well enough
let me ground out my ground probe my
negative probe here alright here we go
I'm gonna just go around the bend here
in Probie Japan I think it's two and
four
let me just probe each one so I got
nothing on that pin nothing on that pan
nothing on that pan
and it's known that one okay we're over
four let me probe the other four nothing
on that one nothing on that one yeah
nothing on that one I think I know what
we have problem with okay no plus or
minus fifteen that's good cuz I don't
have any op amp's that's very good uh
let's see
so plus and minus 15 okay we're gonna
have to take a look at the schematic
here and try to figure out where that
plus and minus fifteen a source from
alright so let's take a look at the
schematics here now we're trying to
identify those source of the plus and
minus 15 volts so if we look on this
page we can see there are two taps off
the transformer one going to bridge d2
thirteen when going to d2 twelve we're
concerned with d2 twelve that's gonna
produce plus or minus 34 volts let's
take a look at where that leads to so if
we look at this page there are two taps
off the plus and minus 34 let's look at
the top one if we look at the output of
that we have plus and minus 15 volts so
that's where we're looking at and
wouldn't you know what look at the two
capacitors in there 220 and 221 or
excuse me
221 and 222 those are the two that
looked to be leaking so that makes a lot
of sense so let's go ahead and take a
look at the board here you can see this
the plus and minus 15 are produced by
two zeros so go ahead and take a look at
those because those could be bad as well
will check for shorts here okay so let's
check across those ears I'm sorry that
was the resistor well that's the Zener
yeah that's right
let's check the other one yep those are
shorted so I wonder if these capacitors
may have shorted which took out the
Zener or vice versa mines will check two
resistors well we're here just to see if
they're shorted no no okay um darn it
that's too bad I don't I don't have any
Zener z-- and if I do I don't know if
I'm gonna have any plus or minus 15 or
15 mil designers sure I have these
capacitors I can replace those resistors
I don't know so I'll probably have a
digit key order its hoping to get this
all repaired tonight and doesn't look
like it so I will get these on order
will replace all six of these components
and that'll at least give us our plus
and minus 15 volts whether or not that
gives us you know it alleviates all our
issues who knows but not all confident
that'll get us our signal past IC 101
there so I'll come back once I have
those in and install the new components
have arrived and I was going to remove
the old components but I noticed this I
wanted to show you first so take a look
at these two joints up here this is one
of the capacitors and you can see that
somebody reworked I don't know if they
tried to remove the capacitor and put it
back in or what but the solder joints
look terrible so it's worth knowing all
the other solder joints for the other
capacitor the two Zener 's and the two
resistors you look untouched so this is
the only one of concern but I'll clean
that up once I put all the new
components in the new components have
been installed no problems there I
cleaned up the bottom of the board quite
a bit as well so we're ready to test
let's go ahead and go to the scope
alright here we are back at the scope I
have my two kilohertz sine wave as my
input to the amplifier and I have
channel a of my scope hooked up to
channel a of the amplifier and likewise
for channel B so here we go I'm gonna
turn up channel a and nothing that's so
bummer
okay well let me try channel B
ah alright so channel B is working you
can see I can adjust the output there
good channel a is definitely not working
so we'll have to figure out what's going
wrong there but at least replacing those
components you know get us one output
and want to figure out what the problem
is with channel II what's going to start
probing to try and identify the issue
with channel a but if we look closely we
can see it right there the trace to both
outputs is cracked and I probed the
board side and you get the signal and I
probe the tip side and we're getting
nothing so really if I just repair those
solder joints there should be back in
business and that bottom one hard to
tell if that's cracked or that's just
the angle that we're looking at looks
cracked I'm gonna touch up all four of
those and we should get channel a back
the only other issue I'm gonna have is
the LEDs on the front they don't
illuminate at least not for the signal
so I may have to replace those but first
things first let's get channel a working
again alright I reworked the solder
connections at both outputs they look
much more solid now so we're ready to
retest again alright ready to test again
I'm gonna start with channel a alright
there we go now we got her signal it was
just those connections there let me
double check channel B
all right
check their linearity so they're both at
the same output right now let me uh
overlay them they look good awesome
so obviously next thing is to actually
test the sound so let me hook up a
speaker alright I still have channel be
hooked up to the scope I'm gonna go
ahead and turn up the volume on channel
a with it connected to a speaker there
we go so again last thing for me to do
to try and get these leds working and
see we have a signal and clip LED for
each channel we should have a signal
illuminated right now I don't know if it
illuminates when it's volumes all the
way down or if it's just if it has an
input I'm guessing if he hasn't even put
it all there's just a simple board
behind these and if there's just you
know white LEDs I think I have some in
stock over place those and we'll get it
working alright I spoke too soon all I
had to do is turn the volume up a bit
more I guess it's got a minimum signal
threshold before the LEDs illuminate so
watch what happens when I turn up the
volume
so they were just fine good
so this one is fixed this was an
interesting one I liked it but it's time
to move on to the next project so I will
see you at the next one
thanks for watching
you
[Music]
