DR #70 - It Lives Again - Proton D1200 Repair & Testing

Duality Repair
132 followers
464 Video Views·Sep 18, 2025
In this video, I document the repair and testing of a Proton D1200 amplifier. Specifically, an event caused several components in the right channel to fail, some catastrophically. After identifying, ordering, and installing suitable replacements, this family heirloom is ready to play again.
Parts Used:
Q620, Q624, Q628, Q632 - 2SC5200N(S1ES)-ND
Q622, Q626, Q630, Q634 - 2SA1943N(S1ES)-ND
Q612 - TTC004BQ-ND
Q616 - MJE15032GOS-ND
Q618 - MJE15033GOS-ND
R640 - 56-PR01000107500JR500CT-ND
VR603, VR604 - 3296Y-1-102LF
This one could be a battle. This is a
Proton D1200 amplifier, and it's in need
of some serious help. I can't even power
it up safely. So, let's remove some
covers and take a look around.
Here's the bottom of the amplifier. This
is where all the action is. Let's take a
closer look at the problem area up here.
This is all from the right channel.
[Music]
You can see all four of these
transistors were absolutely smoked.
This one's leg was blown completely off.
I've been told that this occurred when
performing the idle current or bias
adjustment procedure. So, we'll just
have to keep that in mind.
The goal here will be to identify all of
the failed components. Some will be
obvious like these, and there'll
probably be some other ones that aren't
so obvious. Identify and order
replacement components, get those
installed, and test the unit to verify
it's functional and robust once again.
So let's head to the schematic.
Here's the schematic for the right
channel. I've highlighted all five
components that have obviously failed.
Here are the four transistors mentioned.
And also the bias transistor is missing
a leg as well. Now I'll go through the
entire amplifier. I'll inspect every
single one of these semiconductors and
resistors. And I'll mark up the
schematic with any that are marginal or
completely failed so I can build a parts
list.
I'm all done. Let's review the full set
of failed components. We already knew
about these four transistors.
These two are the outputs on the
positive side. These two, I believe, are
part of the dynamic power on demand
circuit.
The four matching transistors on the
negative side also failed.
The output drive transistors for both
the positive and negative side failed.
We already knew about the failed idle
current or bias transistor.
This fusible resistor 750 ohms failed.
And although it's measuring okay, as is
typical, I will also replace the idle
current adjustment potentiometer.
Here are the components I'll use.
I'll put the full parts list in the
description.
Time to get to work.
All components have been replaced. I
also replaced the left channels idle
current potentiometer. Now it's time for
the fun part. powered up.
That's fantastic. Powered up. Okay. Came
out of protection in somewhere around 5
seconds. That's what I'd expect. And
look at those meters. Huh. They don't
show up very well on the camera, but
they do look very nice in person. Let's
move on to idle current.
Sometimes there's no convenient point
for you to attach your test probes when
adjusting the idle current. So, you have
to make your own convenient point as I
have here.
Per the service manual, we're looking
for 2.5 to 5 millolts across the emitter
resistors. I'm going to shoot for three.
We have the left channel on this left
meter and right channel on the right.
Let's go.
Left channel's perfect. We'll move on to
the right.
Perfect.
Next, I'll calibrate the power meters.
There's no procedure in the service
manual, so I'll use 50 watts. There's
two potentiometers for adjustment right
here.
We'll start with the left channel.
And now the right.
Now let's see how the meters move
together.
nice and smooth.
Now, let's take a look at the signal
integrity from both channels. This is
100 hertz.
Both channels are nice and clean and
even.
This is 1 kilhertz or 1000 hertz.
Still looking good.
10 kHz
and 20 kHz.
No problems.
How about output power? This amp is
rated for 100 watts into 8 ohms. It can
certainly handle higher power, but only
for very short bursts of time. So, I'm
just going to check at 100 watts. Into 8
ohms, that's going to be 80 volts peakto
peak. At 20 volts per division, we need
to hit four divisions. Let's see if we
can get there.
It's about right there. That's 100
watts.
Fantastic.
I've been listening to this amp for the
last hour or so and it's sounding
fantastic. So, I'm all done here. I'll
leave you with a little power meter
deflection from a copyrighted song.
Thanks for watching.
