DR #4 - Mitsubishi HC4000 Projector Troubleshooting and Repair

Duality Repair
132 followers
660 Video Views·Mar 12, 2025
In this video, I document the troubleshooting and repair of a Mitsubishi HC4000 DLP projector. The fix was very simple so it's a short video.
hello everyone this is Nick and welcome
back to another episode of duality
repair
tonight I have a Mitsubishi HD 4000
projector this thing is pretty cool
and should be able to see the fault
immediately
so you power it on and you get the power
LED blinking red and green so after
doing a little bit of investigation on
the internet there is a timer on the
bulb a counter I should say and when the
counter hits a certain amount I think
it's 2,000 hours you might get an issue
like this and you have to reset the
timer before you can power the unit on
to reset it you're supposed to hold the
left arrow the right arrow on the power
button for 3 seconds and then try and
power back up so I'm gonna give that a
shot here and see what happens left
arrow right arrow power alright I held
it for at least 3 seconds you saw the
status menu blink red twice I'm gonna
guess that that needs to blink green if
it resets it appropriately that didn't
seem to work I'm gonna unplug it plug it
back in just make sure it doesn't need a
hard reset after that unplugged plug it
back in
red green blinking immediately so I get
to open this thing up
I'm excited never been inside one of
these units before so I will reposition
the camera and we'll be back and we'll
start opening this up alright we're
ready to open this up I gave it a
once-over just to see where all the
screws are it looks like they're mostly
gonna be on the bottom so we'll flip it
over again I've never worked on one of
these units so I have no idea what it's
looked like inside obviously there's
gonna be some sort of a power supply
there's a bulb some sort of control
circuitry but the details I have no idea
so I just have to see what kind of
screws these have they're just regular
Phillips
and so there's one two three four five
six seven eight eight Phillips screws so
I'll get started on this all right so
after about I don't know 20 minutes of
fighting with this thing I finally got
that top cover off and so here are the
innards of this projector you'll see I
have the control board here separated
it's got this ribbon cable I have this
so we can you know try and activate the
buttons as well as see that status light
which you can see good so I'm gonna
leave it like that for now it's gonna do
a quick visual inspection to look for
anything obvious I don't see anything
obvious at least on this top circuit
board obviously we have a lens right
here probably can't see the lens part
but then it's gonna have the lamp inside
here this looks like it's gonna be some
sort of a driver probably for the lamp
not quite sure it doesn't doesn't say
and then it's hard for you to see but
there's a fan over here and there's a
fan here and there's a fan here and you
definitely can't see it there's a fan
down on the bottom as well and there may
be more fans so we have four fans at
least obviously so a bulb like this is
gonna get really really hot so you know
these fans be working I also noticed as
soon as I pull the cover off there's
this switch here so just curious I'm
just gonna activate the switch and make
sure that is nothing to do with anything
interesting so if you didn't see it
watch the LED when I press the switch
stays read so that I think
and the cover this cover is right here
so it's a switch that should determine
if this cover is in place see
approximately hold go something like
this
well I would think it would activate it
it's curious it's gonna press the power
switch
Wow look at that
I think it turned on no my finger isn't
touching anything dangerous it's just
touching this switch all it does is
close a contactor I'm not near any other
electrical components so so the lamp is
on I don't know if you can see that and
I can see an image coming out of the
lens here so I'm gonna let go and it
should shut off and indeed it does
that is fantastic
it does appear to be working fairly well
so what I'm gonna do now is unplug it
remove this switch we'll take a closer
look at the switch and try and get it
fixed
you shouldn't have to buy a new one I
think I can just repair the switch and
as you know it'll be good to go so I'll
be back when I get this switch out all
right so I remove the switch it was just
2 screws and then unplugging the
connector and so pull it up a little
closer for you to see so you just have
this one contactor here and when it's
depressed just listen can you hear it
click so you can see that little black
node jutting out that's the actual
contactor for the switch so when that's
depressed a certain distance into the
switch it'll close the contact and allow
the unit to turn on and what I was
looking for here was where on this pin
here right here over time switches like
this can be flexed to the point where
they have to be depressed all the way to
the switch in order to activate the
switch and so what you can do there is
you can bend this so that you don't have
to you don't have to actuate this as far
to get the switch to activate but that's
not the case at all if you look really
closely so you see there's a good gap
there between my contactor and the
switch and so I don't have to move far
for it to activate
right there it's like halfway the switch
I think is just fine I believe on the
real issue
so exhibit a this is the one of the
small covers there's only one other
cover on this top lid here show you this
so here's the top cover this lid goes
right here just like that it goes
directly over the lamp module okay and
the switch is directly below this cover
so if you look right here there was a
little node there that is supposed to
activate that switch when the cover is
installed so what the manufacturers
trying to do is prevent people from
opening the cover and allowing the unit
to run so when the cover is open or
removed like this that switch will not
be activated and the unit will be off as
we saw earlier but then I actually found
it I heard something rattling around I
thought I broke something but it was
already broken this little black piece
right here that was it a little node
that was a part of this cover what a
tiny cheap little piece of plastic so
this thing either got moved around or
just got brittle and broke right off so
there's two options I do have some of
course I just dropped it I do have some
superglue I can glue this on and it may
hold it may not it's such a small piece
I don't know if I'd really trust it well
the other option is just to short out
this jumper excuse me jumper out this
switch so that it the unit always thinks
it's activated you know just need to
tell the owner not to open this cover if
the unit is on so I can let him know I
will let him know what I found
I'll let him know what he wants me to do
for now since I think it's fairly easy
access I'm just going to jumper this
and then we'll test it yeah I want to
see how this thing runs so I'm going to
jump her it out I'm gonna put everything
back together and then I'll hook up some
video we'll see how this thing actually
operates so I'll be back all right so I
thought I'd show you what I did here so
I remove the switch the switch used to
be installed right here and then it
plugged in here this little two pin
connector all I did I'll zoom in a
little bit hopefully you can see it all
I did was solder these two pins together
effectively jump ring that out and
creating the switch itself and so you
can see I plugged it in you can see the
the power LED it's no longer blinking
red green it's just a stable red and so
I'll press the power button we'll make
sure it turns on and see if it's working
okay goes to double green I could hear a
relay click fans came on and I know the
bulb definitely turned on it says
Mitsubishi Electric upside down
obviously because they have the unit
upside down
and I'm watching the camera right now
that's definitely that that color
flashing is not happening and in real
life that's flashing that's not
happening I can assure you that there's
this blue right here is is pure stable
right now let's see I can't read what
that says it's out of focus it says I
think it says no video or no signal no
signal it's upside down you can't see
that at all again that that flashing
there that pulsing is not happening this
is purely stable right here all this
blue it's stable that's just you know a
shutter speed difference between the
projector and the camera so okay so it's
definitely powering on that's fantastic
with that switch jumpered I'm gonna put
it all back together probably gonna take
me an hour or so it took a long time to
put it take it apart so put it back
together I'm gonna hook up probably a
DVD player to it it's got an HDMI input
so I'll hook up my DVD player and we'll
make sure it works and we'll see how
good the images and make sure that I
didn't screw anything up when I put it
back together so I will be back when
it's all back together and when I have
my DVD player hooked up be right back
all right I was able to get it all back
together the power back up with no
issues I have my DVD player hooked up
through the HDMI port and the picture
looks really nice focus is really well
so this one is fixed let me get this
back to the customer and we'll move on
to the next project thanks for watching
we'll see you next time
you
