A Christmas Miracle If I Can Fix This 1937 Silvertone Radio!

Amateur Repair Time
257 followers
102 Video Views·Jan 7, 2025
ladies and gentlemen welcome back to
amateur repair time now if you didn't
see the first two videos on this series
I've been working on this super cool
Sears silver tone radio cabinet look at
that
thing what a great looking
cabinet that's from 1937
1938 and um we have the chassis out here
and we're working through it so we
tested some tubes last time and we
worked on the power cord and we got down
to the capacitor just as you get into
the uh just as you get into the chassis
I've got some schematics here that
aren't really the correct schematics but
they're close enough that we've been
able to use
them uh this is for a
101. 482 and this one's slightly
different I think this is a 101. 1488
just barely different it seems like the
difference is this particular one uh had
push buttons I may I may wrong maybe
there's some other differences but we
haven't found them yet so we have done
the power cord coming in and we are
waiting on our safety capacitors
hopefully we'll have them in in this
video these videos take me quite a while
to uh record so by the the end of the
video hopefully we'll have them in and
this shows that it has four dial lights
this particular one only has two dial
lights because it's a just a different
setup and then after it runs through the
Transformer I'm doing everything in
order basically after it runs through
the Transformer it runs right into this
rectifier
tube okay soon as it runs out of the
rectifier tube you have one two
different filter
capacitors so I suppose that's the next
thing we're going to replace if I've got
anything even similar to those now this
tells me 350 volts
here I think it says on the capacitors
450 working
volts um DC working
volts so
going to have to figure out what we want
to do about that I don't know if I've
got anything that strong I might have to
order them
too so one's supposed to be 16
microfarad and one's supposed to be 25
but what they've got in there is um 16
and 24 interestingly
enough and again these are the wrong
schematics so I guess it's just
whatever's close let me see if I've got
anything even similar to that at that
high of a voltage I don't I don't know
that I do well as I thought I don't have
anything that high so
I need to order them but I'm probably
going to have some resistors and stuff I
need to order too so I'll just start
making a list um so I need a 16450 and a
25450 I'll probably end up with a 22 and
a 33 of course it's more modern
equivalents um so that's these so from
there we run up towards our
speaker and there are some small
capacitors on the tone control
and then there is a capacitor here uh
coming between the
output tube and the speaker
socket c23 which is
0.5 speaker socket I think it's on the
[Music]
back yeah it's attached from the output
tube to the speaker socket it wouldn't
be across the speaker socket but I've
got
that we're going to have a problem with
the
lighting what is this bad
boy yeah okay so here is the output tube
likely let's see is that the output
tube it is
so it's a
6v6 it's mounted there on the
chassis the speaker thing plugs in
here so that should be that so let's uh
let's pop that baby out and replace it
all right got it in there I J hooked it
now this is one of the coolest parts of
working on these some people hate this
but I love it uh I pulled the cap out
and it is a0 05 so cool which is similar
to a 472 pretty close instead of 05 it's
047 um but look how they look how the
schematics show it they show it as
attached to the we'll call this pin two
I guess I don't know I don't know what
the configuration
is um maybe that's pin five we'll call
that pin five so it's attached to pin
five and then on
here it's attached to pin
too so it's attached to this pen and
it's attached to this pen well if you
look at it you're like what the hell I
don't that's not right but it is if you
look so the Cap's attached here and then
this side of
it is all electrically
connected to pin two and pin
three right so because of this little
dot right
here Tech technically that point is the
same electrically as that point so if
the cap goes from here to here it's from
there to there it's the same
thing that drives some people crazy I
think it's cool as hell though because
it's like a little puzzle you have to
figure out what in the world were they
doing that's what people are going to
think when they look at my uh my
handiwork down the road what in the
world was he
doing all right so that's that
one um those apparently will connect to
the tone control which is I believe this
one so since it's way over on the other
side of the um the joint there we're not
going to mess with it and I think
that's um this cable here that's running
I think it runs all the way over there I
think so we'll skip that um let's see if
we can find anything else that's around
this output
tube all right so there is a with this
be a coupling capacitor attaching this
to
this
c22 um it should uh go off of one of the
pens of the output tube and connect it
to the detector tube so the 6
B6 is the one that's right next to it
now you could just go through and grab
them all and do them one at a time but
I'm just trying to help myself
understand what the hell's going on you
know what I mean I'm learning I don't
know anything much about these so I'm
trying to track them down on the
schematics and think a little bit about
them and be familiar with them and
that's how you learn things you could
just say okay I'm going take this one
out and put another one in I'm G take
this one out put another one in hey
here's one take this one out and put
another one in but you're not going to
learn a damn thing right if you follow
through and go let me find that one oh
there it is I see how they did that you
learn a little bit at least right that's
how I see it so I'm going to run through
a couple of them and if I find something
uh interesting enough to film I'll do
it all right so several hours has passed
and um I replaced all of the
[Music]
electrolytics I did not replace the
Domino ones there those are capacitors
too I don't really have a way to check
them I guess I could check to see if
they're shorted
but I've heard conflicting things I've
heard some people say oh those are
horrible I've other people say those
never go bad so I don't know usually the
smaller size capacitors at least on
arcade games um you know that I
typically work on um obviously much more
modern on monitors and things like that
but these are monitors from the 80s
um the small value capacitors that are
miciah and ceramic and and all that
never go bad on those so I don't know
[Music]
not sure about these I'm going to find
out though because I'm going to turn the
thing on once I get it all rebuilt and
we'll see if it burns anything up um so
then I went through and I started
checking the resistors that is what took
all the time the
resistors first of all I don't really
have the schematics second um it's
confusing as hell because of that point
to point that I was bragging about
earlier however there is a chart in the
schematic like I said though it's the
wrong schematic so for instance c29
doesn't
exist it's not
there
okay
um a lot of the rest of it is is correct
um so I went through I'm checking the
resistors right oh and it does confirm
that the on the previous video I was
saying that I believe there were
capacitors inside of
the this box that the power was on the
AC went to so I'm glad I took those off
um so yeah so those caps were waiting on
the safety caps
um so going through checking resistor
values like I said it's been really
tough to make sure I've got the right
value but I found four that are pretty
off speec
R16 was supposed to be 500k it was like
900k R17 is supposed to be
250k it's
486k uh R4 was supposed to be 50k it was
like
95k R5 supposed to be 30k it's like
50k um it's a one watt so it's a little
harder to get I had a 500K and a 50k
and I confirm with the parts list on the
side that they're I think it says third
watt actually but it's either says third
watt or half watt so I put half watts in
of course
um so I need a 30k 1
watt and I need a 250k half watt this
r18 um I cannot find in I can't find in
the chassis
it looks like it's saying that it's
right
there but it ain't there
so I don't know what the deal
is
uh well wait a minute I think I see it I
might see it so I'll check it but anyway
um yeah it's very
confusing there's also a couple of them
up
here that I can't check in circuit
because they're charging these three you
can't really check in circuit because
they're charging a capacitor when it
starts charging the capacitor it seems
like it's in Spec though um and here are
the two that I took out I actually went
and looked up the old school color
codes green is the first number the body
of the of the resistor is the first
number that's
five the end is the second number that's
black and then your multiplier is the
dot on it yellow so this is
500k this one is
50k green black
orange so it actually works the same way
they work now is just they painted them
differently
right here's my
old wax
caps so I need these two resistors for
sure and I need um these
two uh Power um uh caps I may have them
work too I'll check these resistors I
think I've got at work I'll check these
caps tomorrow if I don't have them I'll
just order all this Stu so I've got
copies of it and I'm getting low on my
0.1 microfarad 630 volts let me show you
something on the top though that's
worrisome all right this thing screwed
up and I didn't do it I had nothing to
do with
it I don't know how this happened but
there's something going on
with this part of this coil
here I think I think we can fix it if I
can figure out what in the world it
does is it still
connected it looks like it's still
connected let's see how you can twist
it and there's some wires over on that
side that look like they're broke
loose so it looks like at some point
that may have taken a
bump
um it's nothing to do with me but
somebody has hurt this poor thing at
some point it may still be connected I
don't know
but yeah I'm I'm going to have
to figure
out how that's supposed to be
connected
um see I'm going to have to figure out
how that's supposed to
Beed and what it even
is I think maybe it's L2 here possibly
I think so I think it's
L2 but we'll figure that out once we get
the other stuff done we'll take a closer
look at it all right so I need uh I'm
waiting on four caps and two
resistors well I've got great news um
I've been worried about that antenna
coil so I've been looking into it
looking into it I thought about it all
day today not all day but several times
today
that is
L1 it's this piece right here and so I
tried to research it and find some other
uh some other see if I could find a used
one or something I saw you how I showed
you how the thing was
loose it looked pretty
mangled
but I looked into it all day looked over
the schematics and then I just now
looked at it again
I'm not going to show you it on camera
because I don't want to break
it that little coil that little you know
the literal coil of wire is just loose
it's not broke so those wires that are
hanging if you look they're still
connected um so I carefully looked at it
again I actually do not see a broken
wire so I went through and I've checked
that's L1 like I just showed you L2 is a
completely different
coil it's one of
these and then there is also an L3 so
this is L2
L2 and this is
L3 is all three of
these okay over here is also L3 is all
three of
these and if you see basically these are
coming to play Whenever you change the
band so this sucker can do shortwave
police band and broadcast band which we
call am now um so you've got the switch
changes here the switch changes here the
switch changes here and the switch
changes here but most of these you don't
have to worry about in our instance
because these are L3 these are L3 these
are
L3 all that L2 actually is or L1
actually is is this one
coil and this one
coil so I don't completely understand
how it works but it looks like the
antenna comes in and then they have I
don't know if this is an inductor is
what this is creating or whatever but
basically the the signal is coming in
out of the air on the antenna line and
then it's present on these coils and so
depending on which one you have it
connected to it's it's basically I think
I'm just guessing at this it's getting
the frequency in line with this side of
the
coil right and so it's it's either it's
so that it can pick it up you know what
I mean it's like a
pickup that's my amateur understanding
of it so we can actually check these
coils I run into this on pinball
machines you know we have coils all in
pinball machines a coil an inductor a
choke it's the same thing it's just a
piece of wire that's wrapped around
something
so if I measure from here to
ground I should get a reading through
that coil because it's connected right
now from here to here you're not going
to get a an electric reading because
they're not actually connected it's just
the signal is here and it's picked up
here right does that make any sense so
with that
said let's see if I can rig it up where
you can see
it this is the stuff that's interesting
to
me there's 33 ohms resistance between
the antenna lead and the
ground if I turn this
sucker or let me turn it like this if I
turn it up to
the the very top
one
well can I get it to do it
I guess if they're dirty it doesn't help
me all right so in
one setting I need to spray it with some
cleaner I
guess come on show them the
number it's not doing me right
all right so the the potentiometer needs
clean I'm going to spray some cleaner on
it from the antenna connection to
ground on one setting I get 15 ohms if I
change
it let me mess with it a little bit see
if we can get it to pop
in I'm getting
like I'm getting different things
depending on how clean it
is you see it jumping around so that
one's really low it's like two or three
ohms and if I go to the third
one 32 ohms so
32 a really low
one and like five okay so I'm just
changing the three
bands and I'm checking between the
antenna and ground so what is that
telling
us that is telling
us that all three of these coils are
hooked up now notice I'm not actually
messing with L2 but when I change that
knob it's changing it's connecting the
antenna to ground in one of those
positions through my L1 coil that I
think might be messed up but I'm still
getting a connection to ground so it may
be the wrong value maybe it's slightly
shorted or something but it's there and
then whenever you turn it now when I
check from here to ground I'm actually
going through L2 which we believ to
still be intact and it gives me a
different reading and then whenever I
turn it to the third one same thing
gives me a different
reading right I have discovered by just
tracking wires and stuff that this
setting that it's drawn in that runs
through L1 is the broadcast band so
that's our AM radio which is essentially
going to be all that we can use this
radio for I don't know that shortwave is
gonna pick up anything and I don't know
that the police B's going to pick up
anything but it'll hopefully it will but
if it doesn't we defin it we can
definitely pick up all kinds of AM
stations but to do that we would need
this intact and it appears to be intact
I just need to clean that switch okay so
the next one is this one so there's only
two things that that coil does
well this capacitor
C2 is right
here and the wire connected to
that um
is right there and it runs out that hole
so it's connect it's going from
here C2 up into the coil
right which is exactly what you see the
wire is going from here up into the coil
and then when it gets about halfway
through the coil it connects actually to
the anode cap on this
tube so if I check from here
to here guess what I have continuity
because that is still connected and the
only way that can still be connected is
if this L1 is still intact and it is so
then similarly I can connect from the
anode
cap with my
meter up to this now this is C1
C1 is the tuning capacitor
which is a trimmer pot
basically here and I guess this is the
um that's the antenna trimmer right so
you adjust that to basically tune the
antenna so there is a wire running from
here underneath that so if I connect to
that wire and this cap guess what it's
connected as well so although that thing
looks scary as hell this is still
connected and this is still connected
and that's 1 2 3
4 five connections and the thing has
five connections on it that's everything
is still just
fine now I don't have to worry about
that that would have been a pain trying
to find one of those suckers I was going
to look at it and see if maybe a little
wire was broke or something maybe I
could solder it back or something but
when I looked at it there actually
weren't any broken there was just a
couple hanging down and if we leave it
alone alone don't ever touch it again it
should be just fine so now I'm waiting
on some capacitors and stuff should have
in them in soon and we'll put it back
all right folks I got my parts in I got
my two suppression caps in
there um I
replaced oh this
resistor and I
replaced where was my other one oh this
resistor
um filter cap cut the old filter cap
loose it's still mounted of course I
just cut the wires short enough to where
they can't touch anything and short
out um this one was really easy to do
you could just put it right there uh and
then this one up here was a little bit
harder cut it loose the ground to the
where the ground was but then the
positive was way over here so I was I
attached it and used a zip tie to tie it
so it won't move or anything the old one
was was
removed and that's everything so I think
I think we're ready to pop some tubes in
it and bring it up on a variac and see
if it's going to uh short out and smoke
and blow up or what but I got I think I
got to plug the speaker
in
um so maybe I can just move the cabinet
over here where the speaker lead will
will reach I've I've measured the coils
on the speaker and they're both intact I
don't know if they're correct this one
says say that it's 1,000 ohms but I'm
measuring 650 don't know what that means
this one says
400 it but it doesn't say anything but
I'm measuring
400
um so I think we're good I'm I'm
measuring that from the
plug so I'll slide it over here where we
can plug it in I'll pop the tubes back
in it and then we'll hook up a varc to
it and see if it'll come up and do
anything maybe we'll get some kind of
hiss or static or smoke or something all
right right folks so I have a very Tran
plugged in here varc
um it's got a fuse and then I've got
a amp meter plugged in it it's supposed
to be on its side apparently it has feet
on the bottom uh and then I have the
radio plugged into the amp meter so
we're going to see we're going to turn
it on and then as we increase the
voltage we'll see if there's a short
developing which you'll be able to tell
because we'll be running a bunch of amps
through
it um
and if it isn't we'll keep turning up
the voltage until we get something
hopefully now the chances of this thing
working first shot like this very
low and also this um the dial thing
isn't working I got to work on that
later but uh but we can turn the knobs
to try to tune in something um also I
don't have an antenna even hooked up to
it but there's a really strong station
near here it might be able to just pick
up out of the air with what little stuff
that it has and we I'm just trying to
see if I can get some uh some hum or
something going on and we'll see if our
there's any green left on our Magic Eye
if it doesn't blow everything up all
right so I have it on zero volts right
now it's now on also I didn't clean the
uh the potentiometers yet
boy it's kind of stiff
too I don't know if that's going to make
good enough contact in there for the
volume to come through or not but we'll
see it's a little
stiff all right so that's turned up
there's no voltage on it because this is
on zero so I'm going to slowly turn it
up now we're not reforming any caps
we've swapped all of them but we're just
looking to see if this thing starts
pegging
a little bit of movement oh little bit
of movement we're at 30
volts we're
at 60
volts this thing probably hasn't been
brought up up
in 50
years all right so I need to see what we
are on our we're on the
low
scale what am I hearing am I hearing the
radio or is that something
outside yeah I'm hearing the
radio okay that's 100
volts I hear a hum
that's at about 120
there well I electro shock myself
quicker in the dark
again no
antenna the Magic Eye is trying to
Magic I smell the burning smell of
dust take a sip of my water
here we're on the shortwave Channel now
the not
Noti we might let me turn this down a
little
bit I know we're not going to pick up
any short waves
stuff with no antenna all right that
should be the American Channel but
remember I was having a little bit of
trouble with that
so this should be a but again no
antenna let me see if I can get her to
tune a little
bit so here in Charlotte at 1110 WBT
there is a huge Clear Channel station
and it's four miles from my house if the
towers fell over they would hit my
shingles so we may pick that up even
with worn out
tubes a screwed up antenna coil no
antenna hooked up and
um this is cool cuz if nothing's been
through this thing in 50 years you know
what's the first thing it's going to
hear I just heard something let me turn
it up a little louder
what does it get treated to
first you know observing animal behavior
so that was my little Obsession I just
didn't know that that would ever lead
into a
career ium your parents came here in the
60s did you see the eye uh yeah my my
mom was actually one of one of the first
people
out we're not tuned when we tune the eye
will
close tomorrow my my grandmother looked
at my grandfather and said um we're
leaving we're leaving tomorrow and they
left everything behind and and came to
the
US that's pretty gutsy to be able to do
that isn't it my grandmother was
unbelievably gutsy and it's funny
because there's this there's a
photograph that was
taken well that's a wrap yeah saved
another one
the clothes on her back and she was
looking out over the boat as she stepped
on and for for as uh overprotected as
she was on me she was an Explorer in her
own right cuz you know there she was
setting setting s to a place she' never
been a language didn't speak all right
let me see if I can get some music
through it I don't think I can with no
antenna wire but up here somewhere
there's a am music channel that plays in
the middle of the night you're
specialist
and that channel is so loud that it just
it's much louder than the other channels
so you got to kind of turn up the volume
usually to pick anything else up unless
it's designed into the tube
to there's something
oh no we just introduced this silvertone
to wrap a I was trying to Shield it from
that
I wonder if we can get
WBT I mean not WBT WSM
[Music]
with no antenna that would be hard
[Music]
though
no all right so I think it's working I
know it's working
it's not working well
yet thumbs and you know relatively
larger brains compared to body size you
know all the things that make primates
primates they have but they look kind of
like a little
mouse they what of all the Expeditions
you've been on what has been some of the
scarest for you yeah oh let's see if the
tone Works gosh um I get asked that a
lot and most people
but it's actually been
[Music]
people you know I've been charged by um
I mean really
likez
gorillas your adrenaline time like the
midone your adrenaline goes up and
that's like the lower tone you know
large sort of imposing uh very very
strong animal and the elepants have been
chased by Forest elephants that's pretty
scary but in Cong um you know all right
so there you go so next week I will put
it back in the cabinet we'll clean the
cabinet up a little bit we'll see if we
can um get an antenna on it at least
inside the cabinet or something we'll
see if we can get anything on the
shortwave Channel we'll get the lights
working on the dial um we might have to
align it and we'll just see what else we
can do to make it a little better so
I'll see you next week I hope you
enjoyed it it's really cool seeing this
thing come back to life I need to try to
get some knobs for it so I'll see if I
can order some knobs and have them
before next
week but I'm having trouble finding the
exact right knobs I found a picture of
what they're supposed to look like but I
haven't been able to find any for sale
anywhere so leave your comments below
what do you think I think this thing's
going to be awesome once I get it all
back together so we'll see you next time
now if you like watching me work on
these old radios even though I don't
know what I'm doing and you're just
waiting to see if I get the hell shocked
out of
me uh and you don't want to wait a whole
other week to see if it happened this
next week check out this video of a
radio that I did a while back but I got
to tell you I lived through it see you
on the next one the sort of plane Crush
you know
