أدّت الحرب الناشبة في اليمن والمستمرة منذ سنوات إلى ازدياد تخريب التراث الثقافي من خلال الأضرار التي تخلفها الحرب والحفريات غير الشرعية ونهب المواقع الأثرية والتاريخية، وكذلك من خلال الاتجار غير المشروع في المملتلكات الثقافية، بالإضافة إلى تعرّض المتاحف اليمنية إلى الخطر الشديد. بالإضافة إلى توثيق القطع الأثرية بالتصوير الضوئي الفوتوغرافي سيكون من المفيد إنشاء نماذج افتراضية ثلاثية الأبعاد للقطع الأثرية التي تحمل أهمية خاصة للحصول على أفضل المعلومات الممكنة والحفاظ عليها - على سبيل المثال- في حالة فقدانها أو تخريبها بشكل كامل. وستكون هذه النماذج أساساً لتشكيل متحف افتراضي. تعد طريقة (SFM) أبسط الطرق لإنشاء نماذج ثلاثية الأبعاد باستخدام صور متداخلة، هذا ويتناول هذا الفيلم شرحاً مفصلاً عن كيفية التقاط الصور متداخلة للقطعة الأثرية من أجل الحصول على نموذج ثلاثي الأبعاد لها. تم تنفيذ مشروع الفيلم بدعم من برنامج الحفاظ على التراث الثقافي التابع لوزارة الخارجية الألمانية من قبل فرع صنعاء التابع لقسم الشرق في DAI بالتعاون مع جامعة هافن سيتي في هامبورغ.
المشروع: مارن ليندشتيت (جامعة هافن سيتي في هامبورغ) وإيريس غيرلاخ (معهد الآثار الألماني، قسم الشرق - فرع صنعاء) الإنتاج: الشركة - كوردولا جاريدو وكلوديا كوك الصوت والموسيقى: فابيان جاريدو ترجمة إلى اللغة العربية: إبراهيم سلمان - مروة عثمان دورات عبر الإنترنت وأفلام تعليمية على العنوان التالي iDAI.tutorials: https://tutorials.idai.world/
We put the piece on this table
and you can use a small table or cabinet or chair instead of it.
The main thing is to have a stable base
and you must also make sure that there is enough space to move easily around it
and the table should not be too high
to be able to check the piece from above
and it should not be too low to be able to move around it easily.
Basically, we need measurements to show us the dimensions of the piece
because without them, the pictures will not be measurable
because we do not know whether it is large or small.
This gives us the real dimensions of the piece.
The measurements must be placed perpendicular to each other
almost on both sides of the piece and at the level of its dimension
so that it is neither high nor low.
Only then can the measurement of the pictures be done correctly.
The size of the dimensions of the piece must be approximately consistent.
For example, we have a statue that is one meter high
so the dimensions must also be large
in order to be able to shoot the dimensions on the best of their faces.
The lamps allow us to get a bright, consistent light in the room.
This should avoid the sun rays falling directly on the piece
or on its surroundings as much as possible
because this causes an unwanted shade in it.
The lighting of the piece must also be avoided directly
and the possible reflections due to it.
We use a tripod holder to shoot.
By means of it, we can determine the time of taking the picture
in isolation from the surrounding light.
We use a digital camera, a light lens, a reflector
that allows all the necessary settings to be done manually.
One of the most important settings is to adjust the aperture of the lens
and then the camera automatically controls that
according to the intensity of daylight.
If the number of the lens is chosen high with a small aperture
the need for a long light exposure time is increased.
In this case, we use a tripod holder
so that we can take pictures with high clarity and without vibration.
First, we choose the appropriate program from top to bottom.
We now choose program A
and this means that we adjust the aperture of the lens
by means of which the camera automatically determines the appropriate exposure time.
We now point the camera to the piece
and align its right edge appropriately.
This can be seen in the upper part of the screen.
The aperture of the lens must be set to number 13
with a shutter speed of 5 seconds.
The aperture of the lens must be set to number 11 at least.
It is better to have a larger number
because only by choosing a small aperture for the lens,
i.e. by adjusting it to a large number,
it is possible to show the piece in the picture with high clarity.
This includes both the front and rear parts.
After setting the program,
the aperture is set.
Here, we must make sure that all the parts,
including the dials, are visible in the picture.
In addition to that,
the rear must be unchanged as much as possible
so that we do not see movement around it.
By simply setting the aperture distance,
we must fix it to avoid changes in it.
To do this, we can use glue
and it is enough to use a piece of adhesive tape.
After that, the autofocus must be activated,
which is adjusted here on this side.
After that, we check the ISO number,
which can be found in the photo shooting menu.
There we find the ISO settings
and we can see that it is set to the number 100.
In the ISO settings,
it is set to the number 100.
Basically, we must choose the lowest possible number,
and we must also check the white balance.
This can be found in the photo shooting menu.
Here, within the white balance,
we choose the sun symbol.
This is because we are working with sunlight,
which is provided by the windows
and the daylight lamps used.
Here on the side of the camera,
there is a memory card,
on which the photos are stored.
We now specify in the camera
the file format in which we want to save the photos.
We save each photo in two different formats,
so we go back to the photo shooting menu,
and we specify the opening on the number 2
in Roll Plate by Card in Slot 2.
Here we have the option to save the photos
in RAW format,
with a backup version described,
and at the same time in JBG format,
which I would like to make adjustments to later,
using one of the programs.
As for the quality of the photos,
we set the choice of JBG and RAW
to 2000,
i.e. the best quality for the photo.
At the same time,
we can specify the size of the photo
in the image size option,
then we choose L,
which provides the highest resolution
at 24 megapixels.
We can also stop the JBG compression feature,
i.e. we get the best possible quality.
It is very important that the photos
in the format I have just defined,
do not shrink,
cut, rotate,
or compress on the computer.
They must remain as they are,
because this is very important
for processing later.
The last setting that I check
is the option that can be defined
in the Setup menu.
Finally, the last setting must be checked,
which ensures that the photos are not rotated automatically.
The Setup menu contains
the automatic rotation of the photos,
Auto Image Rotation,
which must be set to stop running.
After we have set all the camera settings
and checked them,
we start taking pictures.
For this purpose,
we take pictures from all directions
and move in a circle around the object.
We repeat all these steps
at least two different heights,
so we go around the object twice.
Once from the top,
we look directly at the object
in one way or another.
Now we start the first round of photography.
For the second round,
we set the tripod holder
at a lower height.
We set the camera position
at a lower height
and we have to make sure
that there is no movement
in the background of the picture
through this shot.
We have to make sure
that there are no people walking in the picture.
You can avoid this,
for example,
by placing a piece of fabric
on top of another photograph
that shows the piece
in one way or another
directly from above.
It is important for the piece
to know whether the piece
is open or closed from above
in order to complete the shooting
from all angles and also from the side.
In this case,
we have a piece
that we prefer to take pictures
from below,
i.e. we flip it
and repeat the process
in its entirety,
i.e. on two rounds
at two different heights.
After taking the pictures,
we take out the memory cards
from the camera
and transfer the pictures to the computer.
I create two different files
with two combinations,
namely RAW and JBG.
As for the JBG files,
I divide them
into two additional sub-folders,
one of which stores the pictures
from above and the other from below.
As for the RAW folder,
all pictures are stored
in one folder
and these pictures are used
as a backup file
and are then no longer taken into account.
Next, I start the Agisoft Metashape software.
We are now opening the Agisoft Metashape program
to process the pictures
to create a 3D model of the object.
In this software,
all further steps are carried out.
First, the pictures are read,
then their location is calculated
at the time of the capture.
If this is successful,
all the basic requirements
are ready to create the model of the pictures.
We call it a new project in the program,
then we load the pictures
into the workspace
in the upper left part
and the pictures are added
using the right mouse button.
We choose the appropriate folder
in our case, Object 1.JPG
and select the pictures
and open them in the program.
Then we get a list
in the lower part of the program
showing all the pictures
in a small format.
In addition,
if we open the folder
in a larger way on the left side,
we will get a long list of all the pictures.
In the next step,
we want to calculate
the location of the pictures
at the time of the capture.
For this purpose,
there is a list called Workflow
and we can access it at the top.
Then we choose Align Photos.
This allows us
to adjust some settings.
In general,
we adjust the precision setting
to High.
We leave the selection mark
as it is.
In the advanced selection,
it must be set to 40,000
which is the number of points
that the computer takes from each picture.
We leave the value of Limit
to the number 0.
This means that all the good points
in the processing are used.
Nothing else needs to be taken into account.
We choose OK
to start processing the pictures
directly.
Now let's see what will happen.
Depending on the number of captured pictures,
this may take a few minutes.
When the program ends the calculation,
let's check if we were successful.
Let's now take a look
at the way of photographing a little.
Many things may appear here
other than the document piece
in the middle.
We make the program display the camera
at the time of shooting.
We can do this by activating
the Show Cameras setting.
If we zoom in a little,
we can see the two rounds of photography
in the form of two circles.
As for the pictures taken from above,
we look at the upper circle
where all the locations of photography are specified.
As for the lower circle,
the pictures taken from below
correspond.
We also have the additional shots
from the upper circle
as well as the slanted shots.
Here we realize that the entire documentation
was successful.
Here on the left in the Cameras list
we see that we have 65 pictures
in our project.
This means that 65 pictures
have also been compared.
This was our goal.
Now we can calculate the three-dimensional model.
Now I save everything
by describing it as a project
in my project file
with the number 1 piece
from the top.
This is because in this case
we only used the pictures taken from above.
Now I save it
as an Agisoft Metashape file.
Here we have a set of second data
for the pictures taken from below
which we treat in the same way.
We open the Agisoft Metashape program
and load all the pictures taken from below
and start calculating the pictures.
When we see the result,
we can see two circles
of the upper and lower pictures.
On the left side,
we can see the number of processed pictures.
This means that we have directed
58 pictures from the original 58
and processed them.
This means that we have confirmed
the successful photography.
This means that we have completed
the authentication and verification process.