Перегородка из гипсокартона. Видеоурок. Делаем своими руками. Все этапы

Pavel Sidorik. Renovation and Finishing
79 followers
5 Video Views·Dec 9, 2022
Welcome everyone to my channel this is Pavel Sidorik
and in this video we will be making a T-shaped partition
made of drywall
The installation technology of Knauf partitions was used as the basis
But I added some of my own elements to it
The apartment is undergoing a renovation
Red walls indicate the ones we removed
The new partition is shown in blue on the plan
Red squares indicate right angles
For clarity I'll show you how the partition
looks in cross-section on the technical map
Here all the connection nodes are present and
all the details are described We will need it
Water-resistant drywall 12.5 mm
Partition channels 50 and 75 mm
The part of the partition that will come into contact
with the living area will be made of 75 mm profiles
The same that will come into contact with
the profile corridor
50 mm Soundproofing tape
Fastening
Quick installation 6x40 mushroom head and screws 2.5 and 4.5 cm
We will use
mineral wool for the sound insulation of
the partition We are starting the work
The walls to which the partition will be attached were previously
plastered according to the guides and they are positioned
Strictly parallel to each other
We use a laser level to mark the
floor which has a 90-degree angle
Also transfer the partition outline to the
ceiling using a level and a marking line
Measure the required length of the profile
Cut the profile using
metal shears or a regular angle grinder
When using a grinder use ear
protection and safety goggles
We drill holes in the profile for cables
Attach the soundproofing tape to the
guide rail
Take a photo of the
cable layout for further repair
We thread the cables through the profile
We attach the guide profile to the floor
We use a 6x40 dowel mushroom type
The drywall and two pieces of gypsum board simulate a finished wall
This is needed so that the partition is one
The level with the existing wall
This is important because there will be tiles on the bathroom walls
We perform similar
actions with the ceiling track channel
We measure the partition profile
It should be one centimeter less than the distance
between the profile guides on the floor and ceiling
Connect the guide rail and main
partition profile with a router
Leave a 1 centimeter gap at the top
when installing the partition channels
In the frames that form the door opening for reinforceme
We install the blocks by screwing them to the profile with a press nut
To increase the rigidity of the partition you can use
such a construction by joining
the profiles end to end
We are positioning the profiles at a distance of 60 centimeters
additionally installing the profile that forms the door opening
and the last end profile
Double profiles are secured with lockwashers
Such embedded elements are
necessary for a suspended ceiling
The framework of the first part of the partition is ready
It was made from 50-millimeter profiles
We start attaching the drywall to the frame
We attach the first sheet
We are paneling the door opening
it will be easier to cut later
Leave a gap of 1 centimeter between the floor and the sheet
Leave a space of 3-5 millimeters between
the ceiling and the drywall
Cover with the second sheet
The first layer is ready
We fill the drywall joints with joint compound
We cut the door opening
We plane the outermost boards to match the drywall
We install the second layer
Place the sheets with a 60-centimeter offset
We install the second sheet
We are sewing the last sheet
We mark the electrical boxes
We drill a crown preparation
We install the electrical boxes and run the cable It
must be in a flexible conduit
Now you can start laying the mineral wool
We cut pieces of the desired size and fit them into the niches
Be sure to use a protective mask
We cover the back wall with drywall after inserting the insulation
In two layers with a shift similar to the front side
We only secure the sheets to the vertical partitioning profiles
The partition section is ready
Then we make the partition in exactly the same way
In the scheme using only a 75-millimeter profile
The main advantage of drywall partitions is their light
weight quick installation and good sound insulation
Also a ready-made coating that does not
require plastering for final finishing
They also make it easy to run utilities
such as electricity and plumbing
Friends I've finished the partition this is what I came up with
The technology is actually quite simple I think that
The future belongs to such framework technologies
Thank you for your attention if it was interesting don't forget
Like subscribe to the channel see you next time
Igor Negoda was with you
