Как бороться с плесенью_ Что такое воздушный клапан_ Комплексное решение Аквапанель

Pavel Sidorik. Renovation and Finishing
79 followers
6 Video Views·Dec 11, 2022
Welcome to my channel this is Pavel Sidorik
We are continuing the cosmetic renovation in the panel house
In a two-room apartment
We encountered all the difficulties that
You may encounter it when repairing an
apartment in an old residential building
Ceiling painted with whitewash oil paint on the walls glue from the tiling
bustle everything possible
All that is scraped away through such strenuous
mechanical means But that 's
only half the problem
The main problem is that all the exterior walls in this apartment are
covered in mold and since the apartment is corner-shaped the walls are moldy
And in this video I will talk first about how to deal with
the consequences of mold and then directly how to do it
Remove mold what are the ways and methods
Second we will look at where mold comes from
What conditions are needed for mold to develop
Third it is a comprehensive solution to prevent it in the future
There was no mold that is this insulation this ventilation
normalization all these issues we have addressed
Let's proceed The first
step is directly removing
the mold from the wall which can be done using
Both folk and professional methods
Areas where mold has penetrated deeply should be
Remove it mechanically using a drill
The other areas need to be treated with chemicals
Of course all work should be done while wearing a protective
mask to prevent mold spores from entering the lungs
Also I recommend moistening the
wall first so that the
pores do not scatter throughout the apartment What can be used
First it's a bleach which contains chlorine and
in principle quite effectively deals with mold
And fungus
Second it is regular vinegar which is less effective
against fungus but it is environmentally safe
I had pre-treated the wall with these two products
After consulting with experts they
provided me with a list of recommended products
and I chose this one
This product is made by Knauf I won't tell you the
name because it's in German the language here is German
You can break it I'll just show
you up close who's interested
This bottle is enough for 8 square meters
If compared by price bleach costs approximately
One and a half dollars this little bottle costs five dollars
vinegar is also relatively cheap up to a dollar
Probably
But in these scales where it is used
this method is not worth the cost because if
You will already have done the renovation painting and
wallpapering and then mold will appear resulting in financial losses
It is much more than a $5 savings on a professional
mold removal product It is
very easy to apply to the wall
Apply the spray to the affected
areas of the wall This product
can be simply rinsed off with a large amount of water after 10 minutes
After we removed the mold from the wall we proceed
Therefore we cover the wall with two layers of
waterproofing then treat everything with antibacterial agent
with a composition against mold and mildew and then
we apply the final coating in our case this will be
White-painted gypsum plaster bricks
Now we need to make sure that in the future mold does
not appear we need to eliminate the factors that cause it
Mold appears in apartments now we will deal with them
High humidity relatively warm conditions and poor
Ventilation these are the ideal conditions for mold in
our case it is also possible that the insulation whic
It has lost its properties over time
and the plate is freezing the first problem is to eliminate the freezing
Sheets for this the facade will need to be insulated from the outside
The sides this is done by industrial climbers we insulate
We will use stone wool instead of polystyrene so that the
facade is ventilated there will be a drip edge made there
but in general everyone is familiar with this technology
you can often see pieces of insulated
separate apartments the second point and it is basically
the main one the owner said that the main mass of mold is
It appeared after the plastic windows were installed as it is
known that plastic windows are airtight there is a gap there
The micro-ventilation mode but not everyone uses it
This mode is not sufficient for proper ventilation
Apartments in our houses and these are 99% of the houses that were
Built in the CIS territory with supply and exhaust ventilation
it was planned that due to the tight fit of the frames
Air will enter the apartment through the windows and
doors and accordingly further into the ventilation duct
The apartment will be ventilated but when PVC windows
appeared and they are airtight ventilation accordingly
The problem started here the appearance of
mold stale compressed air poor ventilation
High humidity with all its consequences
First you constantly and regularly open the windows which is extremely
It is uncomfortable and unsafe in winter as you
can catch a cold and for those with small childre
Children if they are crawling around on the floor a draft immediately comes in
and everyone closes the windows The
second point to install an automatic system
Ventilation heat recovery and so on it's expensive
starting from 2000 euros without installation
Many think that by installing an air conditioner they have solved it
The problem of ventilation in an apartment I'
m sorry to say most air conditioners sold are
They do not support ventilation
they take air from the
room cool it and the air ends up circulating around in a loop
There are air conditioners with
a ventilation function but they
are also expensive What is an inexpensive solution in this case
A few years ago when I was buying an apartment the developer
installed plastic windows with air gaps when handing over the building
Valves airbox they indeed perform the ventilation function
The air that engineers intended for the houses
They allow a measured amount of air through them and
That this valve is located at the top of the
window and that no actual spasm is formed
Humidity is normalized plus you get a constant
supply of fresh air
The valve looks like this that's all it is The
price isn't high it costs
20 Belarusian rubles if
In dollars that is 10 dollars
This valve is compatible with any window system
It is easy to install you can do
it yourself now I will demonstrate
It also has a high throughput
of up to 42 cubic meters per hour
We will install it here on the upper
panel of the door After we have chosen the
location where it will be placed
Valve we cut the window seal 350 millimeters and the seal
It is located on the frame
opposite the valve Remove the window seal and insert the seal instead
valve
Then we remove the 350 millimeter seal opposite to it
I install the gasket that
comes with us on the frame
Then we remove the protective film from the valve
Attach the tape and place the valve
on top then secure it with three screws
The valve is installed it works very simply in this
position the valve is closed and there is no ventilation
In this position it's open and there's ventilation here I can feel with
my hand that the ventilation has started it's going along the ceiling
This lever controls the amount of air the more
you open it the more air enters the apartment
So it is completely closed
Valves are made from EBS plastic and
look quite aesthetically pleasing
I also want to say a few words about mold in
bathrooms because that's where mold most often forms
Constant high humidity poor ventilation humidity
It does not
have time to normalize mold forms on the walls
If you take a regular cement-sand plaster and gypsum board
Mold forms on them but not here
Now I'll show it up close it's sold in general
In many stores
It is called Aquapanel these panels were specifically developed
for rooms with high humidity
I took a small piece specifically as a sample for myself
Thank you for your attention of course if it was interesting
Like the channel and
subscribe
to it See you next time
