Потолочный плинтус ! Как сделать угол_ Как клеить_ Секреты мастерства!

Pavel Sidorik. Renovation and Finishing
79 followers
7 Video Views·Dec 11, 2022
Welcome friends to my channel
In today's video I will show you my method for refilling baseboards
There are many videos on this topic on the internet
But perhaps someone will see some nuances some tricks for themselves
Someone rather will come and see the technology
I will show you three ways to cut the baseboard
How to hide the seams of the baseboards so they are not visible after painting
And some nuances secrets
So you see it's going to be interesting
I'll start by telling you what I'm gluing the baseboards with
I'll say right away that I don't use the special glue that comes in baseboard tubes
If my memory serves me right the company Soudal calls it A50
Or other variations
Let me explain why
First of all he gets deeply involved
That is after you glue it it will still touch the baseboard
Secondly it is more expensive than PVA putty
And thirdly I think this is my personal opinion
But still PVA putty holds much better than this glue
I will mix PVA construction glue right now
This is the finishing compound
If you want to make a larger batch of adhesive
mixture then you should not use finish filler
Apply the usual drywall compound in the proper ratio
Apply the desired amount of compound
Then add PVA glue
Honestly I add it by eye
To say that this finish mix didn't become too much of a finish
Also I want to mention one more point
Many use Soudal glue in tubes
But putting the filler into any tube is not a problem
I'll show you now
In principle
in all proportions that I added the intelligent glues do not open themselves
We mix thoroughly
Well the spackling is ready
How do you load compound into a silicone or acrylic tube
Silicon acrylic and just these chips from the
old one With these chips we already scared the stone away
It is very convenient to paint the corners and in general to install the baseboard
To refill you need to remove the back from the silicone
Here I have such a device
I use it for mixing the dough
Ask in a nervous way
Now
I had already filled the filler here before
so I don't need to wash it
But if for example there was
silicone you need to stick it out and
wipe it with a cloth Or just let it fall out
We are starting
Make these movements deliberately
so that it helps to get stuck
We insert
We are pressing forward
All
Applying putty
The second method is
applying it with a sprayer which we took
Now about the ways to cut the baseboard
The first method is using a miter saw Classic
Put on the desired trim
Cut it out
But this is a specific feature
I personally do
Well I don't do it anymore because I'm experienced now
At first I used to make such a template
Trimmed on both sides
And so he kept moving it to
the corner Then it slanted
And then it cut the baseboard properly
Because often you get confused
And you cut it not the right
way Therefore
You see the cut after the bevel
That is a gap is formed
Because the angle is opened
So we'll have to adjust it
manually and trim the leg to fit
The second method is the
visual method We attach the baseboard
to the ceiling We mark it with a pencil
Then we cut it off with this little
piece Now I'll show you
We put in the baseboard
We attach another one to it
We mark the pencils with a pencil or a blade here
And accordingly we insert this baseboard
And we mark it as well
Then we just cut off this point and
angle with a knife at 45 degrees
Here's what came
out Basically quite
good A small gap it can be filled
The third method is using a laser level It is
the most accurate Now
let's see how it is done
To set the laser level exactly at
45 degrees relative to each wall
We measure equal distances
on both walls We draw a
line And we place a dot in the middle of this line
Then we better focus the laser level on the point and the corner
And accordingly we get a straight line at the top
To cut the baseboard Insert
the baseboard First the
right one You can mark
only on the top and bottom
Can we start right away
Draw a line with a pencil
And now we simply cut off our baseboard along the line
At a 45-degree angle
Here is what we have
Some small cracks we will cover using a patch
And for the external corner the scheme is roughly the same
I place the laser level through the middle of the angle
I mark the center
The distance is equal here
Such a small mistake is just
We set up the laser level
And accordingly we cut at the top according to the level
I have attached the baseboard
You can manually trim along this line
The same can be done on the right side
Another little such nuance
A subtlety
When I caulk and already apply filler and join them together
The small cart begins to fall apart
It plays
And to fix them in the correct position I use medical needles from a syringe
I just poke it from below
and above with a
needle It dries up Then I take it out with the needle
There's such a tiny little hole that forms
It gets kind of covered up
Some people even use tape
It seems to me that using needles is more
convenient Secure the baseboard in the desired position
In what order should I install the baseboard
First I glue the most visible corner
Then I glue the already visible corners
That is all the cut-offs end up in such places
When you enter the room it wasn't visible
Another point
I don't glue the continuation of this baseboard right away
I stick this first
Then I insert this here
I'm adjusting it
And there I trim it evenly
It's much more accurate to trim the baseboard with this connection
What to trim the corner with
First this
Then I adjust the corner to the word
And I adjust it according to this connection
Now comes the moment of attaching the baseboard
The baseboard is coated
We take it and attach it
We remove excess glue with our fingers
By the finger and the hand
After we installed the baseboards we
need to fill in any gaps if necessary
And how do you fill these
seams so they aren't
visible after painting Take regular spackling
You can just walk around like that with a trowel
To apply a
thin layer Then to clean I usually
use a knife blade
instead of a putty knife
Because the baseboards are curved
And with such a blade it is more convenient to do
It will have to be done several times and then cleaned
Well friends let's wrap it up
If you found it interesting like the video
Some people have their own methods for attaching the ceiling molding
write about them It will
be very interesting Thank you for your attention
Goodbye everyone
