In this tutorial I will show you how to create an asymmetrical pendant with square and round wire and a pear focal stone. I will show you how to create the main frame, create the details as well as set faceted gemstones and finish off the pendant. Hope you enjoy it! Let me know what you think in the comments, and as always, I am happy to hear any suggestions on how to improve my videos!
We're an artist community (wire and metals) for everyone to share their ideas, post their art, tutorials/events & workshops or ask questions. We are a great buch of artists and have a lot of fun being creative together with challenges and fun projects to create every month.
To see what workshops I am currently running or to get full kits/PDF frames for some of my tutorials, square/half round wire & more tutorials visit my web shop:
Materials you will need: - 0.6 mm (22 ga) wire - 0.6 mm (22 ga) half round wire - 0.8 mm (20 ga) square wire - 20 to 25 mm pear cabochon - 4 mm round, faceted accent stone - 5 mm round, faceted accent stone - 2 mm copper beads - 2. 5 mm copper beads - 3 mm copper beads - 4 mm copper beads - 5 mm copper beads
Hi guys, this is Nadia from Evandicrafts and today I want to show you how to create this
asymmetrical pendant with stone setting. If you haven't already, hit the subscribe button
because I upload new stuff on a regular basis. I quite often make pdf tutorials for the videos I've
put up on here. They also come with kits. I have all sorts of gemstones, square half round wire
and beads and all sorts of nice goodies on my website. So I will pop a link below and you can
take a gander over and see if there's anything you fancy. Last but not least, we have an awesome
wire wrap group which I will also pop a link below. So take a look and come and join us.
Right, let's get started. Right, to begin with, we're going to wrap our base wires. In this case
I've used four base wires. So obviously depending on the width of your cabochon, you want to maybe
use an extra strand or maybe less depending what the size of your stone is obviously. As long as
it sort of covers the thickness of the stone you should be all right. So to bind the wires together
I'm using 0.622 gauge half round wire for this and I just do a couple of wraps, about six or
seven or so in the middle. I always do an odd number so that there is one in the middle when
you put the bend in it but that's just personal preference. Obviously you can do this whichever
way you want. Now what I tend to do is obviously cut the wires off in the middle and on the side
that is facing the stone so that it prevents the wire from snagging. So that's what it looks like
and I just give it a bit of a squeeze so that it flattens down and then I put a bend in it,
kind of like a v-shape. All right, so then I get my stone and I'm going to leave a gap just big
enough for the stone that we're going to be fitting in as the accent below. So in this case
this is a five mil so I leave make sure that I have enough space for the stone as well as the
wire we're going to use to set the stone. So just take that into consideration when setting
the stone. So I'm just kind of shaping the square wires around the stone itself so that it kind of
sits in the middle and we're going to put a bend into the wire near the tip of the stone so that
the wires coming out the top run parallel. You can keep adjusting this, the wire is generally
quite forgiving at this stage as long as you obviously don't work it too much. Then I test
the fit and always make sure you've got enough space left for the stone, the accent stone to fit
in. Right, so next we're going to bind the sides. I should have done this before so this is just to
keep the wires in line. It would have actually been easier if you had done this before shaping
it around the stone so I don't know why I did it afterwards, should have happened before. So I'm
just going to do five wraps or so on each side and once again I trim the wires off on the inside to
prevent any snagging and then I just press the wires down as well with my pliers just to flatten
it out a bit and work harden the wire. I use some fine tip flash cutters and then I squeeze the wire
and just make sure that they are sitting on the same side, the same height on each side and then
you can take the stone and do a fit check again. Just make sure I've got enough space for the stone at the
bottom and it looks fine so far and the next step is to bind the top. All right, so I'm taking another piece of
half round wire. I use 0.6 which is 22 gauge, you can also use 0.8 if you want and if you don't have
half round you can also use round if you wanted to. The reason I like half round is because you
get more width but half the depth if that makes sense. It looks nice and it doesn't look so bulky
when you use half round. So what I'm doing here is I'm just wrapping very gently, I do about four or five wraps
around all of the wires. You want to make sure that they are lined up and squared up so that
they create like a block before you wind the wire around. So I have attached the wire at the bottom
and I'm going to bend the two uppermost wires outwards and then I've got three wires on each
side which I want to separate out and what we're going to do is just take the half round wire and
we're just going to go around the two wires at the top and this is going to be our bell so
keep fighting the wire here a little bit because half round wire as well as square has the tendency
to want to twist and bend out of shape so you just have to be really careful when you're doing this
wrap and keep flattening out the half round wire. All right so I've gone all the way to the top
and I'm just going to fit my stone in again just to make sure that everything is still
all right if it lets me, if it wants to sit in there. So here it is and it seems to be okay so
kind of like fits and next we're going to be shaping the bell just make sure obviously that
each side is parallel. So before we're going to do the bell I'm going to create the seat for the stone
so here I'm using some very fine tipped pliers I really like these I said this many times before
I got these off ebay somewhere they're quite cheap they're only like five pounds or so and
my favorite pair of pliers because they've got a really fine tip. So what I'm doing here is I'm
going very close to the binding wires on each side and I'm kind of twisting it in a clockwise motion
on the left and in anti-clockwise motion on the right just so that I bend the wires inwards which
then kind of creates like a seat for the stone to sit in and at the bottom here near the base I'm
just going in a little bit further to give it more of a ledge and also a bit more support for
the accent stone that we're going to be adding later. So it looks like and then you can see
the stone and test the fit seems to be all good so far so quite happy with that and sometimes
the wires are pressed together so I have an extra fine pair of pliers so this is a watchmakers pair
of pliers also from ebay search watchmaker pliers you'll get this an extremely fine tip I'm using
this to separate the wires I quite like it for fine work when you need to pull wires through a
gap you can't reach normal pliers or so and these are quite handy obviously they're very delicate so
you cannot use them for any heavier gauges they bend out of shape really quickly so but I find
them quite handy. So I'm just using these to create a little bit of a gap between the wire
so that it enables me to bring in my bigger pliers and actually using these to pull these
so the 0.8 which we've used at a 20 gauge is quite soft so we can use these to
pull the wires over the top and do the same at the bottom so what I'm doing here is I'm folding
the uppermost wire ever so slightly over the stone just enough to hold it in place
so that's that and the next step is to shape the bail so I wanted a fairly long bail so I've used
45 centimeters I'm not sure what that is in inches but I will usually put the conversion in there for
and create a fairly long bail and I'm very gently bending those two wires over the top
and then I'm going to separate out the square wires at the base and I'm just going to wrap
each wire around the respective wires three wires on each side to bind the balance and set it in
place okay all right so next step is to take these square wires and I try not to
twist them sideways so that they stay nice and and flat I hope that makes sense
and just you want to make sure that there's a flat surface touching the three wires at all
times because if you twist a square wire it tends to increase in in size somehow and become a lot
more bulky when you twist it around other objects so trying to be nice and flat nicely squeeze and
just make sure that it holds up tight and going out there's the bail set and just make sure that
the bail is the the sort of round section of the bail is right over the stone so that there's nice
balance in the design all right so now I'm satisfied with that and we're going to start
with our first detail section so what I'm doing here is all these wires on the right hand side
need to come upwards and through the bail itself so I'm just taking each one at a time
and again try not to twist it if possible you want to make sure that it stays the same flat
side up I hope that makes sense and we're going to bring these through the bail and position
them in readiness to create our first sort of detail I'm going to bring the last one up and
they will always bend out of shape and look like a dog's breakfast at this stage so don't worry you
can always straighten them out later and we're just going to position them and that's what it
should look like so far okay so straighten them out a bit and now from now on this is all organic
organic design so nothing that I make will look exactly like what you make it's just a sort of
general direction that I have shaped the wires in so what I'm doing here is I'm going in an
anti-clockwise direction and I am shaping them over and then down towards the right hand side
of the pendant so over the bail and then out towards the right and this is just sort of the
start of the design itself and I make sure that the wires all sit nice and parallel to each other
and then I'm taking the utmost wires and create a swirl with two of them and the third one kind of
stays put on the inside this is just so to give it a little bit of a different interest that's
what it looks like so far so good and obviously adjust them to your liking take your time with it
and you only continue once you're satisfied with the look so I'm taking one of the wires and I'm
wrapping it around the bail just to give it a little bit of of strength and make sure that
nothing is loose if you have too long a length of swirls it's not very secure so I tend to attach
the swirls whenever I go and to make sure that they are you know tightly attached to the frame
so on the right hand side I am bringing the three right hand wires and I'm shaping these
in a clockwise motion towards the stone and then back out towards the left
and then the innermost wire oh sorry the outermost creates is create is shaped into a swirl
now just make sure this is for a four millimeter stone setting just make sure that the the stone
setting the loop is big enough to hold the stone but not too small to let the stone fall through
obviously it's not too small to let the stone sit too high up you need to make sure that when you
twist the remaining wire over the stone and there isn't too much bulk there to make it stand out too
I have a problem to keep the stone seated which will happen you get better with that
as practice comes along then all I'm doing here is I'm very slowly shaping the wire over stone and
really just take your time with that it gets much better with practice as well and kind of let the
wire do what the wire wants to do so don't try and force it and just kind of follow it
and it will kind of lay itself over the stone if you're not a hundred percent satisfied with the
way the setting sits you can always tweak it with a pair of pliers obviously very very gently
adjusting the wire as you go and that way you can tweak it until you're completely satisfied
always take care to try not to mark the wire too much okay so quite happy with that and next we're
to take some of the half round that's left over from the bail if you've cut it off just take
another piece I as I said many times before my work always looks like an octopus because I never
cut any wires off just in case I'm going to use them at some point later and so it always looks
like spaghetti junction when I do something so this is why and so I'm just reusing what I had
left over from the bail and I'm attaching the three wires that we've taken from the left
to the frame and bind them together so once that's done I'm just going to make sure I'm also going
through the frame just so that there's extra strength added to it so I'm going to feed it
through the top and the frame and very gently pull it through and make sure it's tightly attached to
the frame itself okay so we're going to carry on with the actual design so the innermost wire
actually need to put my glasses on because I can't see the innermost wire is going to be shaped into
an anti-clockwise swirl and I'm often using my pair of pliers to adjust them as I go
so feed them along and just shape it to your liking and I always try and make sure that
my swirls are nice and round not everybody likes them round so you can keep them a little bit
oblong if you prefer that and I'm going to shape the remaining wires on the outside
so follow the same curve and we're going to take the innermost wire and create a
clockwise swirl so feed it through and take your time with it and I'm going to place it
sort of in the middle of the pendant and as I said earlier you know this is going to be a very
organic design so you can follow the the path that I've taken but obviously it's going to be
the way you want it to look all right so then we've got the remaining bit from the inside and
we need to attach it to the frame at some point so I'm going to bend it inwards and before I'm
going to do that I'm just going to create another swirl and the swirls I create on each side
are going to be smaller in size the further down I go so they're quite big at the top and sort of
medium size in the middle and then a bit smaller at the bottom just to create a little bit of detail
and some interesting sort of pattern and I adjust it until I'm happy with the shape like so and
then as I said earlier I like to attach these loose tendrils let's call them to my frame so
I'm going to go through the base here where the accent stone is going to sit
and just very gently feed it through and then all I'm going to do is do one wrap around these base
wires this tends to fight me on occasion so just use your pliers to very gently adjust I never
force anything too much I always tend to wiggle and push and pull gently and that way you have a
the wires so I'm shaping the outermost wire and I'm going to create a little
swirl at the base a little tendril towards the outside and that's what it looks like so far
right so happy with that and now I'm going to fully attach
the wire at the base here so bending out the one that I face so I upshot here a little bit
sometimes I can't see properly with the camera overhead so I'm kind of rolling the square wire
around the frame to get the shape right and then I use my pliers a lot to position the wire and
squeeze it and as always try and keep the flat side of the square wire in contact with the frame
and that's what it looks like so far and I'm just going to trim off the wire and always
try and trim it off towards the inside so that there's no snagging all right so happy with that
so next again bring the half round if you've got any leftover and we're going to be attaching
the swirls to the frame just two or three wraps and always try and place them in an
inconspicuous area so they don't stand out too much but I like to tie them down because
otherwise they just get bent out of shape if they get hooked all right so happy with that
so now I'm trimming off the half round wire and as always try and make sure they are trimmed off
where they can't snag like that I'm going to do the same at the bottom here bring these in
the pliers in and then trim them off and that's what the left side looks so far so that's all
done we're going to move on to the right hand side now right so I'm going to do exactly the
same on the other side so I'm taking here the innermost square wire and I'm creating a clockwise
swirl so that's what it looks like so far and again I'm going to use my pair of pliers to
adjust the shape and the size and and the general look of the swirl and I take the middle wire and
I kind of position it towards the outside and I'm going to go a little bit further down towards the
middle of the pendant and then create an anti-clockwise swirl in the middle of the pendant
use pliers to shape and if you have round nose pliers you can use those as well if you prefer so
nothing no technique is ever set in stone you can only ever learn how to create something from
somebody else and then apply your own sort of spin to things and whatever works for me doesn't work
for you and vice versa so it just depends how you like to do things I'll show you how I do
my techniques and then you make them work for you all right so again bring a piece of half round
wire and all we're going to do is do a couple of wraps around two of the wires and the two wires
that we're going to attach those two wires to the frame two is enough and again this is just to make
sure that you know if anything any part of the pendant gets hooked on something it doesn't get
damaged all right so I've attached it and I'm going to trim off the square wires and I'm going
to continue shaping the square towards the bottom so I've only got a small piece left
and I've used a little bit less wire than I have put in the description for you and so you will
have a little bit more length left and because I thought it would have been nicer to have a bit
more wire to play with so you have a little bit more to to work with and so I'm going to shape
the last wire at the bottom and I always kind of go the opposite direction of the previous swirl
that just creates a little bit more detail and and an accent really I always squeeze the end
when I create swirls with my pliers so that's to kind of taper out you'll see that in many of my
videos like so and then once again obviously we're going to tie this down and you could still do
something with the remaining wires I'm always loathe to trim off any wires because I think it's
a sin to you know get rid of perfectly good weaving wire or detailed wire but in this case
I think there's enough detail there so we're just going to trim them off also the video would be
too long if I started doing more with it so if you still have these left over you can do whatever
you want with them create more swirls do more stone settings or put a weave in whatever you
like to do with them so I just trimmed them off and that's what it looks like so far all right
so this is a stone setting and there is a link to the stone setting below in the description
and I've put a video up for that so I won't put in this video otherwise we would be here
for a while so once we have done the setting I just slide it through the pendant and slot it
in place below the stone that's the gap we left previously and then I just kind of open up the
outsides the wires there and I find a space on the pendant on the frame to very securely
attach these in place now if you don't really know how to do the setting and it's too complex
you can use a drill bead instead all right and the last but not least it's my favorite part
it's the accent beads I really like using them whether it's silver or copper or any other
material I think they look great so I always have a sort of stash of my beads I've got them on my
website as well if you want to have a look and that's that that's the whole pendant done so
thank you so much for watching I really hope you enjoyed this and obviously don't forget to hit the
subscribe button as I said because I upload new stuff on a regular basis you can come and visit
me on any of my social media I've got Instagram, TikTok, obviously the YouTube channel, Facebook
and obviously don't forget to visit my wire wrap group which is called Wire Wrappers and
metalsmith artists worldwide we're a fun bunch we always do some great challenges and we always
have some fun banter going and last but not least I have got kits, pdf tutorials, gemstones, beads,
you name it everything that you would need for wire wrapping on my website so I'll pop a link
below and you can pop in and see if there's anything you fancy and that's it for me thanks
for watching