Hi Guys, In this tutorial I will show you how to create an elven inspired wire pendant. We will start by creating the wire frame from individual pieces, which will hold a gallery wire setting. We will be creating each component, shape each with a hammer and weave them all together in preparation for your focal gemstone which will be securely set in place as a free-swinging drop focal. Next, you will create a simpler prong setting for the accent stone; however, if you find these stone setting techniques too challenging for now, you can opt for using drilled stones and setting them in place with a piece of wire instead.Hope you like it! Leave a comment below if you have any questions. :)
Materials required:Materials: Wire: • 3 m (118.1 in.) of 0.3 mm (28 ga) wire • 1 m (39.4 in.) of 0.6 mm (22 ga) wire • 1 m (39.4 in.) of 1.3 mm (16 ga) wire
Stones: • 1 x 18 mm pear stone (mine is a mood stone) • 1 x 8 mm round faceted stone or CZ
Beads: • 2 x 1.5 mm beads • 2 x 2 mm beads • 2 x 2.5 mm beads • 2 x 3 mm beads • 2 x 4 mm beads • 2 x 5 mm beads • 2 x 3.5 mm accent gemstone beads
Tools: • Flush cutters • Chain nose pliers • Round nose pliers • Flat nose pliers • Vernier calipers • Steel block • Domed chasing hammer • Polishing materials
Hi guys, this is Nadalia from Ebani
Crafts. And in this tutorial, I want to
show you how to create a wire woven
pendant with a pear focal and a prong
set faceted gemstone as an accent. My
new book on wire work twisted is now
available on my website and it's
jam-packed full of great techniques such
as stone setting, various weaves, um,
bales, and all sorts of other useful
information. Um, it's a great book for
beginners and more advanced artists
alike. So, take a look, um, and see if
it appeals to you. You haven't already,
hit the subscribe button because I
upload new stuff on a regular basis. I
quite often make kits and PDF tutorials
for the videos I put up on here, and
I'll pop a link in the description
below. Um, I also have all sorts of
gemstones, square and half round wire,
some beads, and all sorts of other
goodies on my website. So, take a gander
over and see if there's anything you
fancy. Last but not least, come and join
us in our wire wrappers and metal smiths
group on Facebook. I'll also pop a link
below. Right, let's get
started. Right, for these kind of
designs, I tend to draw stuff on paper
just because it helps with figuring out
where I want what to go. Um, and then
you don't have to bend the wire to just
try and figure out how things going to
look. It's much easier to just take an
eraser and erase stuff if you don't like
it. There are some software
programs that you can
use to draw as well if you have access
to
those. Otherwise, you just get an idea
and then what we do next. So, for these
different length, we're using different
lengths of wire. So, the center one it's
10 cm. For the smaller one here, it's
eight. Um, and then for the heart, I've
used 5 cm. I'll put all of those in
inches. So, we're going to do here. This
is the length that we are going to use
to design the middle one. So, I'm just
going to grab a
ruler and a pair of pliers. And then
we're going
to find the
midpoint.
Um, which is roughly about here. You
want to make sure that everything is in
the middle. So, I'm going to set this
aside for
now. Bring this up a little
bit. And then just make sure that
everything is in the middle.
We bend this
aside. And then just to double check,
make sure that each side is symmetrical.
Same length. 35
roughly.
And that's roughly 35. Because if they
are not the same length, then the loops
at the end um are not going to
um to be symmetrical. So next I'm going
to shape one side. I always find it
easier to shape the right hand side. For
some reason I can't really do the left
side. So then I just flip it
over and do the same on the other
side. And then we're going to take a
pair of round nose
pliers and just curl the end in. So tend
so I want the end to be thinned
out. I used a pair of round nose pliers
and I gently squeeze the end as I
rotate. So, this is quite thick wire
uh
1.316 gauge just because
um it's loose components. So, that they
will be woven together at some point,
but it's better to use thicker gauge to
help
you. Right. So, going to shape this. I
like to make sure that the loops are
exactly the same shape on each end. So
do the same on this
side and use the thick part of my round
nose pliers to grab the end because you
have more surface area to grab hold onto
something and then you can come
in and rotate these. So rotate your
wrist rather and the wire at the same
time. And that gives you a little bit of
control over
shaping these curls or the swirls
rather. And then you can kind of decide
and then you can bring back the drawing
and just make sure that you then adjust
this
accordingly. Let's bring this back in.
and kind of lay this up. You can see the
other side also needs to be brought in a
little bit more. I have made a template
for this. You can get this
um on my website if you want if you
don't want to have to draw your own. I
have a template available on my website
so you can just download it. So, you're
just going to keep working on these
components, these individual components.
I mean, I've only made three, but you
can add in as many as you want, you
know, different layers and can make this
design more
complex. Um, and just add in as much as
you want. Right. So, we've got these the
first
component sorted. And now I'm going to
create the other two or and then we're
going to join all of these together.
Right. So I have created three
components and you always want to make
sure that the ends fit into each other.
So to make sure that they're nice and
sharp, you can come in with a pair of
pliers and kind of squeeze right
near the
edge. And that makes sure
that try and zoom in here that these
bends are nice and sharp. Then you
obviously want to line them up and just
make sure that they all fit together
like
that. And the tips are going to slot
into each other. So they're going to be
a little bit wonky. So what we need to
do is just come in here. Just try and
zoom in
here. And you want to lay them flat. And
then just ever so
gently tap them. Not too hard cuz we
don't want to deform
them. Flip them
over. Do each one of these like that.
You can, if you want to, flatten them
completely and texture them with um a
texturing
hammer, but I find
they weave better together when the wire
is not textured and flattened. So, I
just tend to keep them as
is. And doing this will also work hard.
Not that you need it with a heavy gauge
wire really, but hammering will also
work harden the wire.
which will make it even
stronger so that the design won't
actually bend
apart. And that's what we've
got at the moment. So all of these now.
So the next step is to um bind this
together with some wire. So I've cut my
0.3 mm wire, which is your 28 gauge. And
I'm going to start with the lowest. And
I'm going to wrap it once,
twice at the center there where the kink
is. And then we're going to bring
in the next wire. Place on top. The next
shape. We're going to do the same
again. So
just one
wrap. And then we're going to bring
in the
last. And again, one full
revolution. And it looks something like
that at the moment. And don't worry if
things are still a bit loose. So you can
hold it like that. That's what we've
got. So we're going to do the same on
the other side. I like to
flip this because I don't like working
on the left hand side. So but
everybody's different. So going to be
doing the same. So there's two wraps on
the bottom here. So I'm going
to bring this back up. And then as on
the other side, we're going once around
the middle, once around the
top like
that. And then we're going to travel
back down again. Do the same. Once
around the
middle and then once around the bottom.
And the reason we're doing both sides is
just so that
um we can
control where these wires sit because
it's much easier to
have them tied down the middle. So now
they they they're tied down fairly well.
And what we can do next is come in with
pair of pliers. We're going to be
pushing
in the weaves like that.
And the same on the other side. In
actual fact, for that you can use your
bent nose pliers if you have any. This
comes in
handy because you have more better
access
to the weaves. Push these
in. And now because they're tied down,
you can then arrange these to make sure
that the gaps and the positions and all
of that is all right. Like that. And
then we're going to continue weaving
these in place until it's nice and
tight. So that's what we've got at the
moment. All right. So I've roughly done
about six or seven sets on each side. So
now what I would like to do here is add
some beads as detail. So, we're going to
do is instead of the sort of block
weave, I'm going to go into a figure of
eight weave, which is once around the
base and then I'm going through the
inside and I crisscross the wire over
the other
side. So, what happens is each time I
pass through the
middle and then I
crissross so
that the the weave kind of creates
the V effect. You can see how it's
already starting to build. And this is
just so when we are adding the
bead that it
will sit
central as opposed
to on one side. You can see the weave
here is sitting across.
So then you need to just check if the
gap's big
enough for one of the beads. I think
maybe do one or two
more like
that. And now it should be all right. So
what I'm going to do is add a small
bead to the
end like so.
And then I'm going to attach it. There
we go. That fits in nicely like that.
So, next I'm going to make a couple of
wraps at the bottom
here just to accommodate the next speed
we're going to add in, which is going to
obviously be slightly bigger to
maintain the sort of
um flow of the design. So, you're going
to just need to decide how many wraps
you need in between each bead. So this
largely
depends on the size of the
bead. Um so the bigger the bead
obviously the more space you need in
between. And these wraps at the top and
the
bottom will help you
maintain that spacing. So I'm going to
do a couple of more gap wraps here. So
now I've
got another bead to add in which is
again slightly bigger.
feed that
through and then push this
in and then
create another wrap. So also because
there's a smaller curvature there at the
bottom while at than at the top you need
to compensate for that.
um and maybe create more
wraps at the top rather than at the
bottom to sort of close the gaps a
little bit. So now I'm going to add in
the next
bead and some
fourth that
in. Make sure I'm zoomed
in. And
then just going
to attach
this like so.
You can just
see when you
follow. So, you're going to use attach
beads according to the gap available.
Um, you may need to extend this a little
bit and mold these two wires to suit the
beads you have. But obviously, when you
do that, just make sure you do it
exactly the same on both sides so that
things are symmetrical. Right. So, I'm
going to add a couple of more beads yet.
Um, and I think at the end we're going
to join these two together, but we'll
get to that in a second. All right. So,
I didn't like the gap that I had at the
top here. So, I have added um a
different color bead so it won't take
away too much from the flow. And then
I'm going to add in the 4 mm bead here.
Um, like that.
So that way the flow is kind of
maintained but the gap is also filled.
So you're going to just need to gauge
how it works, you know, for
yours like that. And you just need to
play around because each design is
obviously
different.
Um, you know, depending on the size and
the shape and whatnot. So you're going
to need to play around with that a
little bit. So now I've added that in.
And now I'm going to see if I can fit in
a 5 mil bead as the last
bead. So I'm just going to extend
that and
then add 5 mil
bead and see if it actually fits in the
gap. And if it doesn't, I'm just going
to open it up a little
bit like
so. So that it fits
in. So I'm going to need to come
in from the
inside like
that to tie it
off and then push it in. So if it
doesn't quite fit yet, just fiddle
around with the spacing a little bit.
And that's what I've got at the moment.
So, usually when I finish
off. All right. So, I'll tie this down,
but don't close it off completely yet
because if you like to add some chain
later on, um it'd be nice to add this in
behind the bead so it can't slide out
again. So, I've just sort of
provisionally tied it down, but I'm
going to leave this in place. You're
just going to need to be gentle working
with it so that you don't, you know,
manipulate it too much and then the wire
may break. All right. So, what I'm going
to do is I'm going to repeat this what
I've done here on the other side and
then I'll be back for the next step.
That's what we've got at the
moment. All right. So, I have added a
chain to the top swirl, which we're
going to be using later to hang the
pendant from. But if you wanted to, you
can also add a chain as decoration on
the side here. So, I've got another
piece here. And then sometimes these
little links on these
chains are too small. And then you can
bring in a pair of pliers like that and
make the the ring at the end. Squeeze
it to make it a little bit more round
because the wire that these go on is
quite thick and the links are quite
fine. So you squeeze a little bit. It's
a bit fiddly now, but you get the idea.
You can see that the
link is a little bit rounder than the
others. Um, and then you should be able
to slide it
on like
so. It's always a bit harder to get it
around the curvature. There we go. But
it's on now. So, now that these are on,
you can then bring in the last
bead. And oops, it's going to slip out.
Just bring these up the top. Doesn't
matter if you have the right length yet
as long as these are kind of attached to
the loop because you're going to close
this off
now. Bring this
round. And then you can actually cut
this off a little bit cuz you don't need
it that long. That makes it a bit more
manageable. Bring it
through and then wrap
it around a
swirl like that.
And then just tighten it up a little
bit. If you want to, you could even add
one more bead, I think. But I think
that's enough cuz you don't have a bead
big enough. So then I'm just going to
wrap this a couple of more times.
because obviously the wire that we have
now wrapped is just hanging around loose
here and you don't
really want it to open up again. So,
what I tend to do with these
wires, see if I can zoom in a little bit
so you can see, is I just bring this in
around, let's call this the
stem of the wire that goes through the
bead. And then I wrap
it
around the stem. And what that
does, it works away that loose
end and at the same time also gives the
bead a little bit more
stability like
so. And that's that. And then you can
come in and trim it off. So now you've
got your chains attached in case you
want to use them. I mean if you don't
want to use them, you can just cut off
the last link, but I'd like to have them
in place. Um, so that if I want to do
something with them, I can do that. And
I'm going to do the same on the other
side. And this is what we've got at the
moment. Right. So I have now added all
the beads and I've got both the chains
that I want to use for the neck piece.
They are going to sit on top here. And
then I've added some chains on the side
here because I have decided that I might
just um create some some drops here. And
I've added these in so that they are
tied in place with the beads. Okay. So,
I don't really know how long yet, but
I'll obviously tell you. We're going to
probably attach these like that. Um, but
before I do anything else, uh, I'm going
to lost this. Um, which means I'm going
to oxidize it. Um, and I'm going to use
a paintbrush because I'll try and avoid
to, um, put the beads in loss because
they're really a pain to polish. Um, so
what I do for that is I heat up um
water, hot water obviously, and then put
a drop of loss in it and use a
paintbrush to, you know, paint it on the
wire where I want it to to darken. Now,
obviously that doesn't work the same as,
you know, dunking it in the loss. Um,
it's not quite as potent, but it still
works. But if you want to avoid, you
know, sometimes gemstones or like these
beads, you can't really submerge it.
That's another way to do it. So, I'm
going to do that. Um, and then I'm going
to add the
beads. I mean, the chains to finish off,
and then we're going to add the the
detail gemstones, the drops, and all of
that. All right. So, that's what we've
got. And I'll be back in a jiffy. So,
I'm now attaching the last chain and
I've opened the link rather than try and
slide
it.
Um, because these are so small, the
links I have a hard time to get them on.
And then I squeeze this
shut and then it's
attached. So that's what it looks like
at the
moment. Right. So next we are going to
create a prong setting with um an 8 mm
stone and some 0.6 22 gauge wire. I will
pop a link to this tutorial below. Um,
and what we're going to do with this is
we've got the legs at the back here, and
we're going to attach this to the heart.
So, I'm going to
feed the
stone. See if I can zoom this in
better. So, now this stone is going
to sit
here. Bring it in
here. And then we are going
to attach it. We want to have the lower
side at the base, the lower side of the
knot further down. Just going to bring
this in
here and
attach this to the heart. Let's do two
wraps
first. Like so. You want it to obviously
be in the center.
Then I'm going to do the
same on the other
side. Like
so. And that will
then
seat the stone like so.
And then I think maybe we are going
to close the heart a little bit
more just so that they touch. Careful
not to damage the
wires with your
[Music]
pliers. So just manipulate it. And now
it's closed.
Lastly. All right. So, next we need to
create a gallery setting. I'll pop the
tutorial for that one in the comments
below. Um, but so basically what it is,
it's one base wire attached
to a row of
prongs which will then
hold focal stone. And then I
just wind these together like
so. Um, and what I've used for this are
0.6 or 22 gauge round
wire. Push this
in. But yeah, and because this is a
separate tutorial that I've already
made, I'm going to pop
this in the comments below so that you
can then create it. Now, obviously, if
you feel this is um too complex yet and
you want to create something that's
that's less complicated, you can then
use a drilled bead or a drilled pair or
anything else that's easier to attach so
that you don't have
to create one of
these. So, this is what we've got.
like
that. And then what we're going to do is
this wire on the inside is going
to
serve as the
platform. So always kind of bend this
inside so that the stone has got
something to sit on.
And I only used 0.6 mm wire just because
I don't want the setting to be too
bulky. But I've compensated for that
by creating lots of prongs rather than
just
um four or five, which I would if I were
to use a heavier
gauge. That's obviously just how I do
it. Um so people tend to do do it
different ways also.
Right. So, that's what we've got. And
then I mean I've also got
these. So, I've
got I've got one of my mood
stones which I quite like. All right.
So, I've created a setting. As I said,
the links below. So, because we're going
to attach this to the bottom of the
pendant, we need to create a little wrap
loop. So, I've
used the outer legs of the prongs, and
I'm going to
wrap one
side around the other like so.
And then you want this to be
as really as tiny as
possible. So you're going to
create a tiny
tiny wrap
loop. So just need to check where this
wire is coming from. So this wire is
coming from the back. So we want to wrap
the other
side in the opposite direction.
So, I'm going to create a loop. And the
smaller or the closer to the tip of the
um pliers you go, the smaller the loop
will
be. So, we want to make it quite
small. So, I'm going around the
front and
then to bring this
down a little
bit. Normally these loops are quite easy
to make. Just made a hash of it this
time around. So then bring it down. And
then we're going to wrap
it around the base. And because we're
wrapping
it in the opposite direction of the wire
at the back, these two ends will meet.
And then you can just come in here and
trim these off and then they'll meet. So
this is what we've got at the moment.
Right. So now we're going to attach
this. If necessary, use um a Tpin or
anything else to create a gap so that
the jump ring
fits. And then
just bring it
through. It's a bit of wiggle.
Go. Oops. Fell off the other side.
That's okay. So, you see, you wanted the
loop to
be as small as
possible so it doesn't stick out too
much. The jump
ring and going to close it
off. And that's it. So
[Music]
now it's
done. That's the pendant done. Thank you
so much for watching. I really hope you
enjoyed this. If you haven't already,
hit the subscribe button because I
upload new stuff on a regular basis. If
you feel like joining our artist
community on Facebook, I will pop a link
to the group below. We're a fun bunch,
so feel free to come and join us. I also
have social media if you want to follow
some short stories that I put up
occasionally. And I've got Facebook, Tik
Tok, Instagram, Pinterest, and obviously
YouTube. Also, link is below. And last
but not least, visit my shop if you're
interested in getting some kits for
these tutorials, gemstones, beads, wire,
um, and all sorts of other things. So,
as before, there is a link to all of
that in the description below. And
that's it for me. Hope to see you next
time. Bye.