Hi Guys, today I want to show you how to make this intricate hammered pendant from start to finish 😊 'Skadi' is the Norse Goddess of winter. With its icy blue glow, the focal stone truly suits it!
- 0.4 mm (26 ga) wire - 0.6 mm (22 ga) wire - 0.8 mm (20 ga) wire - 0.6 mm half round (22 ga) wire - 1.3 mm (16 ga) square/round wire - Oval cabochon 15 - 25 mm - Tear drop cabochon 10 mm - Copper beads 1.5, 2 & 3 mm - 8 mm brilliant Cut CZ or gemstone
Tools:
- Heavy duty cutters - Chain nose pliers - Round nose pliers - Bent nose pliers (optional) - Domed chasing hammer - Steel block - Needle file - 800 - 2000 grit sand paper - Polishing materials
Hi guys, this is Nadja from Bunny Crafts and today I want to show you how to create a hammered wire
pendant. Don't forget to subscribe because I upload new stuff all the time. I quite often do
kits for these tutorials and I have half round and square wire and other pdf tutorials on my
website and my etsy shop so hop over to check out what's available if you like. If you want to share
your make join our wire wrap and jewelry artist worldwide facebook group we're a fun bunch so
come and join us. Right so let's get started so we're going to begin with our thick wire so now
I've used square wire for this just simply because I like the integrity it creates the square profile
allows the wire to grip that are going to wrap around it very nicely so I really like using it
for structural components but if you don't have square you can definitely use round as well that
works and doesn't really matter as long as it's quite thick so that it doesn't bend out of shape
so we're going to create a navette shape or marquise shape depending on what you call it
and we're going to make it just big enough so that the stone sits comfortably in the middle
and has a bit of space above and below so obviously that's going to change with the
size of stone that you have just adjust it roughly to that so we're going to bend the legs so that
they are parallel and make sure the shape is is nice so we're going to next grab a piece of
half round wire again if you don't have half round you can also use normal round wire I would
go with your 0.6 wire then as well because that's a little bit thicker than your 0.4 but again it's
personal preference the half round is beautiful for this sort of application because it's half
round flat profile gives you the width and the shine of the wire but it doesn't give you the
projection of a round wire if that makes any sense so what we're going to do is we're wrapping this
wire around the two bail legs as I call them should have got a better name but that's what
I call them so you're going to wrap this until we have about I think this is about four centimeters
I didn't actually measure it but you can this is again personal preference it doesn't have any
bearing on you know the sort of structural side of things so it doesn't really matter you can
decide how long you want it um so we're going to continue until we reach the top and I've got a
little bit of wire left over so that's what it looks like so next I'm going to bend this forward
this is so that when I create the um the round shape with my bail and that it doesn't the loop
doesn't sit at the back I hope that makes sense um but you'll see what I mean just now so we're
going to bend the legs outward a little bit and then we're going to fold this in so you can see
because I've bent the wires forward a little bit the loop that I'm making kind of sits on top of
everything next I'm going to attach these together and then we're going to use the um
the leftover wire to create the back frame that's what it looks like so far so next I'm going to
separate out the leftover wires and these are going to become part of the backing where the
stone will sit in so I'm splitting this in half and you can measure the length if you want you
can use a marker pen if that makes it easier um I go by eye which wasn't always a good thing
because it can get skewed but luckily you know wire like this is easily adjustable um at this
stage so you can go by if you want to I'm just going to bend these in and that's what it looks
like so far so it's kind of like a diamond shape in in the center and then I'm going to bend the
legs outwards again grab this bottom and kind of bend it up again you can you know use a ruler and
you can use a marker pen cokie we call it in South Africa and I have to actually remember that I
mustn't call this here because people don't know what I'm talking about um so yeah marker pen and
it's really important at this stage when you are attaching this wire which is what we're going to
do next that you do it really symmetrical this is important for the small accent stone that we're
going to slot so now we've got the shape I'm going to trim off some of the wires at the top
because I'm known as the octopus queen I've always got a bit of wire left over in this case I'm
cutting it because I'm going to use what's left to bind the um frame to well the inside frame to
the outside frame basically really easy so just basically lash um the outside to the inside um
whichever way you see fit and as long as it's secure it doesn't really matter how you do it
because it's going to be mostly hidden anyway I generally tend to go around each frame once
there we go and then I'm going to flatten it out with my pliers I'm going to repeat this
with the other side and I'm also going to do the bottom to bind them together
so once I've done that the next step is to attach so it's going to be a little bit fiddly because
obviously it's quite a thick wire so just really take your time with that don't rush it um I find
if I rush I tend to wire doesn't tend to behave the way I want it to so if you take it slow it'll
work much easier so kind of guide the wire and squeeze the loop as you go along I'm going to
attach like that as I said earlier it's really important that it's symmetrical and so that there's
exactly the same spacing between each wrap so that the accent stone whatever you're going to um
to going to add is actually sitting right in the center so if one wrap is a little bit higher than
the other the accent stone is going to be quite skewed so next we're going to shape one of the
legs upwards so I've already bent bent it inwards so if you have a look here there is a little kink
at the bottom which is going to hold the um amethyst pair in in place so again it's really
important that both sides are symmetrical so I'm going to do the other side so I bent it in
and this is how I'm doing it so I'm holding it down I'm using a pair of pliers again you could
measure it but I I've just gone by eye which isn't as I said not always the the best way
um because it sometimes can be a bit skew so it's always better to if you're not sure how to do it
and to maybe measure it then I'm shaping the wire I'm using my fingers to kind of give it a
rounded appearance like that and obviously remember if you have a bigger stone or smaller stone you
need to adjust the wire length but it's always better to go longer rather than shorter for
obvious reasons and all right so the next step is we're going to thin out the um the ending of
the wire so we're going to use my round nose pliers and what I tend to do is gently squeeze
and taper the wire so if you use a little bit of force it will thin the wire at the end and it
gives you a beautiful um beautiful finished sort of swirl end if that makes sense so I've squeezed
it and now I'm twisting it and that's slightly now again the the lengths of this will depend on
on your stone and you kind of fit it over the stone so that the swirl just sits on top and
catches the stone so we're going to do the same on the other side so now I've done the frame and
I've kind of molded it around the stone so you need to adjust the wire fold it sideways and
press it into the stone so that the wire hugs it like this and then we test that everything sits
so next we're going to bend these swirls outward again so be gentle because obviously
the more you bend especially heavy gauge wire the more brittle it becomes so don't bend it
back and forth too much because it will break especially if it has got a mark somewhere and
which weakens the wire already so be very gentle and careful with that and so we're going to hammer
the swirls only you can hammer the um the wire as well I mean I didn't do I mean the bottom
wires as well I didn't um I just hammered the swirls and just remember what hammering is
you know when the blows need to travel in a direction you want the wire to expand so when
you're hitting it go slow you don't need much force just when you're hitting it go into the
direction that you want the wire to expand I've got several tutorials that I've done
on hammering so you can have a look at that as well if you want more detail on that I've done
quite a few um where it shows you exactly how to do the hammering um so to get the detail on the
inside I use the sort of round ball side of the hammer so that I can reach right in so that's
what it looks like and just make sure they're quite even so frame's ready so I've molded the
shape some more to make sure everything fits 100% so I'm slotting in my stones again to make sure
that they sit 100% I'm quite happy with that so now we're going to move on to the next step
we're going to make coils so um this is a fun technique I absolutely adore working with coils
and the way this works is we have two base wires so one is the small base wire and one is the big
base wire and I'm using a Bosch drill which has got a sort of adjustable chuck which is
makes work life so much easier you can hand coil them but this is so much quicker and you'll see
why for just now so we're going to grab the 0.6 which is the 22 gauge wire as the base and our
0.4 26 gauge as the um the sort of weaving um coiling wire so we're taking both of those and
we insert them into the chuck and I'm tightening this as much as I can um so any you get these
drills quite cheap on eBay or so second hand it doesn't need to be expensive at all like 14 bucks
or something like that so and it works like a dream I use it for all my coils and there are
purists out there that don't like using drills and I think it saves a lot of time so I'm quite
fond of it so make sure that you have it going in a direction that you're comfortable with
mine goes clockwise so then I put my thumb over where the wire sits and you can see that the sort
of base wire wants to flip flop around and you have to go quite slow so it's going to be quite
frustrating so at the beginning you just kind of push and hold in place now to help this from
uh flopping or stopping it from flopping around what I do normally is I either have a some tube
or anything that I can slide the wire in for the purpose of this tutorial I'm using an empty
wire roll and I slide the wire in which will stop the roll or the wire from flopping around
like that obviously you have something a bit heavier so it doesn't move like it like this does
and but you know it shows the technique so you can go a little bit faster get your thumb over the
wire the wrapping wire to make sure that it's nice and neat and you just have to be careful not to
pull too hard you can see at the beginning of the chuck my wire starting to buckle slightly
and that is because there's resistance there so be careful because you can shear your base wire if
you pull too hard so that's that done and the next step is to take a thicker base wire which is 0.8
20 gauge and we are going to wrap the small coil small base wire with the coiled wire onto that
bigger base wire so I'm starting off with a couple of wraps and then I am simply looping
that smaller coil or that coil we just created with the 0.6 22 gauge wrapping it around that
new base wire so this is generally the wire that is then going to be used you know to continue
your designs and to add detail you can also trim it off but I quite like to use wires like this
that come out with the 0.8 wire to create further details in my design but it's personal preference
so once we've done that it's much easier when you have a couple of millimeters
wrapped so then you can start by coiling it so everybody's got slightly different techniques
on how they do their coils this is what works for me so you're just going to have to kind of
try and see what works for you and yeah just twisting and take your time with that and it's
quite important that the the small base wire is long enough because when you are twisting
the coiled wire tends to expand and grow and slide along your 0.6 millimeter base wire
and because obviously it's being pushed along so it needs to be the base wire the small base
wire needs to be long enough I'm just going to continue wrapping and if you wanted to
the you can use the the small base wire to continue coiling on your big base wire that
creates some added detail and in this case I haven't done that I have just used the base wire
to tie off the coil so I've only wrapped a couple of times but you could just carry on and create
some nice detail so you could just go all the way up to the top of whatever is left of the
small coil base wire and looks quite nice in some designs um so in this case I haven't used it so
what we're going to do next is using the leftover base wire I mean a weaving wire and we're going
to slot this wire I'm going to twist it and the sort of shape of the coil will guide this wire to
sit into the grooves and I quite like doing this because it gives your coils a very refined look
very smooth you can already tell the difference between where the wire is wrapped around and
so I just continue to slide the wire or slot the wire into the slots and then all I'm going to do
is at the end give it a couple of wraps and I tend to pull quite hard to slot the weaving wire into
some of the wraps of the 0.6 wire I hope that makes sense then I'm going to just trim it off
I'm doing the same on the other side and that's your coil so then you can press down on each end
if you wanted it to be tight in the middle so it doesn't move um but yeah that's your coil
so I made two uh exactly the same length and one thing I would like to say to that is also make
sure you make them both at the same time cut the same length of wire at the same time to make sure
that you have um exactly the same length because each coil um is slightly different obviously from
the last because you know it's handmade and they're not always perfect so we're going to
slide these coils in near the bottom and then near the top and we're going to kind of wrap these
coils around the stone I'm going to pull this in so gently on each side and then I'm going to wrap
that's what I was talking about earlier when when I said you could use the um
base wires for the decoration so I've got these coil base wires and I'm going to use these
to do some more work with later so for now we're going to attach these to the frame
I'm going to go just behind the wrap where the frame attaches to well the the stone frame
attaches to the main frame so you want to make sure that it is behind so on the upper part of
that you wrap it around there a couple of times twice I've only done it once there but do it twice
so that it's nice and tight I'm going to do the same so it's still quite easy to add
wires at this stage because there's a lot of space and quite a few gaps
it can get quite tricky when you have a busy piece with a lot of wires but
you'll always find a way to slot the wires in I'm going to do the same on the other side it
can be a little bit fiddly um just take your time with that and remember to attach the base wire
behind I'm going to attach to the top as well it's quite satisfying actually to
to be able to attach these and eventually get something that resembles a pendant so
that's what it looks like so far so next um there's quite a few videos I think that use this
technique so I will put a link to underneath this tutorial to show you how to make a prong
setting so I haven't added it to this video to keep the lengths quite short and I've made a
tutorial for this already so I will direct you to the link for that so we've created a prong setting
and we are going to slide this eight millimeter stone in place and I'm going to use the legs
of this setting and I'm going to attach it to the frame so the outside frame
not the inside so I'm going to um attach so bring it across and I'm going to
shape it around the frame oh rubbish I've actually attached it to the inside frame first
I thought I hadn't okay so um it can get quite tight at this stage so use your pliers
got some fine tipped ones which I love because they really help me to grip wires I've also got
some watchmaker pliers which are really really fine and which are fantastic for grabbing weaving
wires when you want to pull them out you can see so make sure you keep your finger over the stone
it's still quite loose at the moment obviously and so it will pop out don't worry if that happens
we're going to tie it off later so make sure that the stone is very secure you don't want
it flopping around so just make sure when you attach it on the other side that it's nice and
tight as well and wrap it around the frame twice I'm just showing you once here otherwise the video
would be far too long so just do it twice okay so once we've attached it that's what it looks like
there we go so next we've attached it to the outside frame so we're bringing it up
and we are now going to bring in a piece of weaving wire and we're going to find the midpoint
and slide it through the bail and what we're going to do is create a very simple sort of
hand-wrapped coil on the two inside most is that what you call it that inside most
top wires so just feed it through you're going to wrap it just take your time it's always a little
bit more difficult when you're close to the frame I use my pliers quite a bit to push the weaves
together I'm quite a slow wrapper um because I do a lot of adjusting and pushing and it's okay
I find it works better for me I'm going to continue I've got a good length here and just
make sure you've got enough so that you can fold it again as I said it's going to change with you
know different sizes stones it's kind of adjusted um to what you want it to look like so if you
make it about four or five centimeters and then we're going to just feed it through the frame
right underneath the criss-cross so we want to use where you want to use where the stone frame
is attached to the main frame to hold it in place so we're going to attach it to the lower part
of the pendant again fight the wire in this case um because it doesn't want to go through so again
you find you find pliers work I'm going to pull this through and we're going to pull it until it
meets the weave that's what it looks like so far I'm going to do the other side as well
so we've attached this at the base we've got both of them attached
and now we're just going to use the remaining wires and we're kind of going to follow the first
wire and we're going to attach it underneath right below so this is just detail there's nothing
structural to it so um just um you know create a shape that that's pleasing to your eye and attach
it below the first wire with two wraps on the frame as I said I don't show you both wraps
because it would take forever it's quite tricky to get the wire through so I've attached it now
I've saved you the uh watching me do it so I fast forwarded so now we're going to create a very
simple two by five wrap so we're going to start with two wraps around both wires I'll put a little
insert on the side here and to show you what I'm doing and then we're going to do about five wraps
around the top wire so super easy so it's two wraps around both base wires and then five wraps
around the top base wire only and we're going to repeat this and I always tend to again push in my
and then I'm going to continue with that so again it's your two wraps and then I'm going to do I'm
going to go and do two base wraps around the base wire five rather sorry what am I talking about
today all right here we go let's wrap this around I'm using my pliers to push the weaves in that's
what it looks like so I'm going to continue with this on both sides until I have enough
so remember obviously again it changes for your stone for whatever size you have
um so once we've done that you can always test it before attaching it to see if it kind of
looks the same so you're going to fold it upwards we're going to follow the same shape
and then the first few wires um to roughly give it um a sort of layered look so we're going to
fold it up on both sides and then I always work on both sides at the same time just to make sure
well so when I do one side I always do immediately do the other side because for me personally it
helps me to create better symmetry it may not work for you and you know different people to
do it different ways it's just what works for me and but I always recommend to do one side and then
immediately after the other because it really does help with symmetry and you can adjust as you go
along and it just takes a small unevenness in a symmetrical piece to kind of set off a chain
reaction so um yeah for me that's what works so next at the bottom we're going to bring
the one leftover wire and we're going to bring it on the inside of the amethyst and now it's
really important to kind of wrap this wire um on the inside pointing pointing not towards the
center of the stone but towards the outside of the stone and the reason being is we want to wrap
this wire we want it to be as close as possible to the amethyst sides because we're going to kind
of lay it over the sides of the stone so once you've wrapped it around the frame we're going to
pull the wire in and we're going to do the same on the other side so I'm going to push this through
and this is why I wanted the wrap to be on the outside um pointing going towards the outside
rather than the inside I think I'm going to put an insert in so that you can see what I'm talking
about so that's what it looks like attached and now we're going to use a pair of pliers
to adjust that wire we're going to fold it and mold it around the stone of course keep it nice
and tight and I'm going to do an extra wrap around the frame generally if you only see me do one wrap
do two and that's what I'm doing I'm just not showing you both because otherwise we would be
here all day in some cases so just pull that through and that's that's secure so we're going
to do the same on the other side now obviously so that's what it looks like um so we're nearly done
so we're going to do next is use that wire that left that last wire and we're going to follow
again the initial shape and travel up the stone and we're going to attach that wire to the frame
somewhere wherever you can find space and obviously the smaller the sort of distance between
the last point of contact and the attachment to the frame the better and because obviously
there's less of a sort of floppy length I hope that makes sense so pulling it through you can
see it gets a little bit more difficult as you get get the pendant gets busier and then we're
going to adjust the shape and we're going to do the same on the other side as well bend it up
and I'm cutting off all the unnecessary wires I'm always quite reluctant to cut them off because
I always want to use them for something else quite often so next we're going to use a piece
of 0.4 wire you can also use 0.6 if you want to use thicker wires and adding a couple of beads
just enough to make sure that the stone is held in place the stone should be quite secure
um but I always want to add extra security for it not to fall out anyway and so I'm going to
use this to hold the stone in place so I'm going to fold it on one side and add my beads to the
other and I'm going to attach to the frame on each side so fold that through and make sure it
goes through the arch of where we created a little swirl so that there's an extra anchor
that holds it in place and then we're going to attach it to the frame on the side here so just
bring it through there and attach it to the frame so and yeah that's that so trim off your last wires
and that's the whole pendant done so I really really hope you enjoyed this and thank you so
much for watching don't forget to subscribe and and if you want to see what I get up to
and visit my instagram and my facebook and obviously if you want to share your work and
join our community group visit wire wrap and jewelry artists worldwide group on facebook
and again lastly but not least I always have some interesting little tutorials on my etsy
shop in my etsy shop as well as kits for these tutorials so pop over and check them out and
and see what I've got so thank you so much for watching and see you soon