Как сделать люк под плитку на магнитах и экран под ванну за 30 минут!

Pavel Sidorik. Renovation and Finishing
79 followers
6 Video Views·Dec 11, 2022
The new channel Perforator is gaining momentum already with more than four thousand subscribers
This channel will be interesting for everyone who is interested in construction and renovation Great content and high-quality filming
Link to the channel in the description
Hello friends greetings to everyone This is Pavel Sidorik your host with a channel about repairs and renovations
Today I'll show you how to make a simple and inexpensive access panel that won't ruin the appearance of your bathroom
Also I will show you how to make a bathtub surround from drywall
This is one of the most commonly used options when renovating a bathroom
I'll start with the hatch It will be attached using furniture magnets
A two-part set The magnet itself and a metal plate Another guide profile UD is also needed
Sheet metal screws 2.5 centimeters The tools needed are metal shears and a drywall saw
Drill The shower tray is made from moisture-resistant drywall In our case it is Gyproc Aquastrength 15 millimeters thick
The size of the inspection hatch is determined based on the tile layout
Usually it's done so that an entire tile is opened and there are as few cuts as possible But keep in mind
The size of the hatch should not be too small as it is necessary to service the trap and to make a replacement if needed
This is an example of a finished hatch with a cut-off furniture handle
For the video we will make a hatch of the exact same size
We mark the outline of the hatch with a pencil
Cut the drywall opening as accurately as possible
And of course we immediately vacuum up all the trash
We mark and cut the profile for the drywall according to the width of the opening using scissors or a grinder
The profile is the base to which the magnets will be attached
We then attach the magnets to the profile using a screwdriver and regular metal screws
The magnet with the plate must be flush with the profile so that the hatch does not protrude from the screen's overall plane
We attach the magnets one by one Usually I use three on the bottom and three on the top
We turn the drywall sheet over and mark the top of the hatch with arrows
We attach the magnetic profile to the edges of the hatch using 2.5 cm metal screws
We attach the cover and mark with a pencil where to glue the corresponding metal plates
We place the plates in their proper locations and
We glue them with glue Moment Apply a thin layer of glue to the surfaces to be glued and leave it for 10-15 minutes
Then we press the glued items together with effort
The key point is the pressure you apply to the items not the layer of glue The stronger the better
Here's the hatch and ready Now all that remains is to stick tiles on it
This is the cheapest and easiest way to make a flush mount hatch
Since the inspection hatch is not opened often you can opt for an inexpensive magnetic hatch instead of a costly built-in one
Now I'll tell you how to make a vanity top from drywall
Before installing the bathtub you need to attach support blocks for the profile I was lucky as these blocks were already glued on at the factory
If there are none we attach a regular board with liquid nails or silicone It can even be done entirely without cutting it into pieces
Fasten the track to the studs considering the thickness of the tile with adhesive and drywall
We additionally foam the cavity under the profile with mounting foam
We start assembling the framework for the drywall after installing the bathtub For marking I use a laser level
I then attach the lower guide profile of the UD and the side parts of the CD using polyurethane sealant
This allows everything to be mounted very accurately without having to drill into the tile
We insert the main profile into the guide
For the frame I used a profile with a thickness of 0.6 millimeters On the left side there is space left for an inspection hatch
Fasten the profiles together using self-tapping screws with a washer
We cut the drywall to the desired size and screw it to the tracks
The screen is ready Only the inspection hatch which I showed in the first part of the video remains to be done
Thank you for your attention If you liked the video of course give it a like Also subscribe to the channel and leave comments See you again
