Hi Guys, in this tutorial, I will guide you through the process of creating a wire pendant featuring layered weaves. We will start by creating a frame and then seating the focal stone within it. Next, I’ll walk you through the steps to create and shape the intricate weaves that will enhance your pendant’s design. Finally, I’ll show you how to make a prong setting for the accent stone, bringing everything together to finish off your the pendant. Hope you like it! Leave a comment below if you have any questions. :)
We're an artist community (wire and metals) for everyone to share their ideas, post their art, tutorials/events & workshops or ask questions. We are a great buch of artists and have a lot of fun being creative together with challenges and fun projects to create every month.
Materials required: Wire: - 5 m (196.9 in.) of 0.3 mm (28 ga) wire - 1 m (39.4in.) of 0.6 mm (26 ga) wire - 1 m (39.4in.) of 0.6 mm (26 ga) square wire - 1 m (39.4in.) of 1.3 mm (16 ga) square wire - 1 m (39.4in.) of 0.6 mm (20 ga) half-round wire
Beads & gemstones: - 1 x 18 mm pear gemstone - 1 x 5 mm round cut faceted gemstone (I have used an amethyst) - 2 x 1.5 mm - 3 x 2 mm - 7 x 2.5 mm - 7 x 3 mm - 2 x 4 mm - 1 x 5 mm
hi guys this is Nadia from eban Craft
and in this tutorial I want to show you
how to create a wire woven pendant with
a peir focal and a prong set faster
gemstone as an
accent haven't already hit the Subscribe
button because I upload new stuff on a
regular basis I quite often make kits
and PDF tutorials for the videos I put
up on here and I'll pop a link in the
description below um I also have all
sorts of gem Stone square and half round
wire some beads and all sorts of other
goodies on my website so take a gander
over and see if there's anything you
fancy last but not least come and join
us in our uh wire wrappers and metal
Smiths group on Facebook I'll also pop a
link below right let's get started all
right so we're going to grab a piece of
square wire I've used 25 cm which is
roughly about 10 in something like that
but I'll put the
description below or the measurements
rather um we're going to find the
midpoint um and you can use you can also
use a marker pin to help you just kind
of eyeball
it um and then I'm going to do is create
a sharp you want a sharpish Bend where
the Stone's going to
sit straighten that out a little bit and
the stone is going to sit somewhere here
and you want to kind of follow the
shape of the stone so rounding off the
bottom a little
bit do the same
here like
that and we're going to shape it just
remember leave a little bit of space for
the decoration so we're going to attach
other
wire like that
something like that maybe a little bit
more rounded anyway you'll adjust that
um and make it fit the shape of the
stone so then we're going to bring that
in and double check it I'm going to open
it up a little bit more because we need
space for the wires to
attach like
that check the stone
got a little bit of space all right so
then next is we're going to arrange it
so once you happy with the shape um to
place the stone and then we're going to
decide on where we're going to make the
bend at the top so I want to make sure
that where they're Crossing is in line
with the base and that will kind of be
your your point again you can mark this
with the marker
pin and we want to bend these up
so try and make them line
up as best as possible you want to make
sure that they
are that they run in
parallel like
that like
so all right so next we're going to be
binding these together so I'm just
anchoring a small piece of
0.622 gauge wire
putting it around the base just
once like that just to give give it a
little Anchor Point you can hold on to
it
with your hands and then all I'm going
to
do is wrap it as tightly as
possible going to go
around keep going and you keep tugging
and
pulling like that
once once it's all anchor what I like to
do is also come in and push these down a
little
bit just to make sure that it's all nice
and tight and then also ever so gently
press it down a little bit and then we
can just rotate it and obviously try and
make sure there's no space in in
between so just going
around and I'm just going to keep doing
this
until we've reached the top so I'm going
to do
that right so once we have wrapped the
half run wire around we're going to go
and bend this so that we can create a
Bell so I'm going to do
first is take a pair of pliers and we're
going to bend it backwards like
that and that will give us that will
make sure that when we're bending it
over it um has a little bit
of the pendant will actually be
scentered so what I like to do is take a
pair of pliers like that and I'm bending
it over just to stop the half front wire
from sliding
up as you bend it over because it has a
tendency to kind of create little gaps
in between so just keep my pliers over
Top Bend these out a little bit as
well and then just
continue see if I can stay zoomed in
here so put your pliers
back and then just kind of
continue to flatten it and that way it
kind of avoids there will still be
little gaps but if you have your pliers
on top it kind of avoids
you know having the the massive huge
gaps like that so that's what we've got
at the moment all right so actually I
bent it open again cuz we need to bring
the legs through so I'm going to bend
the legs so that we can bring it through
the frame and then we're going
to straighten them out
again and don't forget to use your
pliers
and we're going to feed that
through like
that and then we're just going to
attach the
leg to the side
here all right so just one RB is enough
because the wire is actually quite thick
for such a small
frame you can just bring it through and
if you have a difficulty to get the wire
to tighten up you can wiggle it like
that and that
will tighten it like
that and then obviously squeeze it
down like that and I don't want to cut
this off just yet because I don't know
what I'm going to do with yet so we'll
leave it there and then we'll come back
to it later once we've decided so
obviously do the same on the other side
and then we're going to add some weaving
wires or some base wires for the weaves
that's what we've got at the
moment all right so that's what we've
got now so next we need to add in some
wires to create a backing for the stone
to sit on um so we're going to do is cut
some zero 6 mm wire which is 22 gauge
and we're going to find the
midpoint and then we're going to wrap
it around the
base like
so and you just want to make sure
that it's tight so we're going to do two
wraps on each
side and try not to make it stand up on
it it's not so crucial when it's thin
wire like that but when it's your
thicker gauge
wires try make sure that I'm zoomed in
here
there when you've got thicker gauge
wires and they stand on edge it's a bit
more of a problem because it creates
bulk so squeeze this
down and then we're going to do the same
on the other
side we don't want
to have too big of a gap i' want needs
to be right at the bottom for the design
I have in mind so going to bring it
across and then do the same and just
make sure that the wire obviously also
sits at the top when you bring it
across like
so going to tap down like
that and then one
more and obviously adjust it until
you're happy and then we're going to
squeeze it
down can Shuffle it up with your your
wires so that's what we've got at the
moment so we're going to be
adding uh another set here another three
sets here and then one set set at the
top so I'm going to be doing that and
then we'll move on to the next
step right so I've attached all of the
wires so the important bit is that you
have one cross member at the back here
that will support the stone at the top
and obviously when you place it in there
it should fit nice and
snug near the base so that's all right
like that so when I tighten these up the
wires
um if this is not quite the right size
in the middle you can take a pair of
pliers and you can kind of twist where
the wrappers and that will then tighten
up the line on the
inside and straighten these out and
obviously you want these to be at um as
near the tip as possible you place the
stone in there and then the next step is
to create the weave so we're going to
start with the two sets of WI on the
base so I'm going to cut my
wire and I'm going to find the midpoint
and then I'm just going to start by
anchoring it on the
bottom so I'm going to bring this
up and I'm just going to create three
wraps around the base two
three like that and this is to
start and then you may need to bring in
your pair of pliers you want to bring
this wire a little bit closer and you
may need to put a little Bend in it just
so that it comes closer to the wire
below and then we're going to go do two
wraps around both of them don't worry if
they're not perfect yet it's always a
little bit shoddy looking in the
beginning so going to go
two open this up again and then we're
going to go and do
three around the base like like that and
then two around the top or I mean both
ways not the top
rather and
then create a weave like that and when
you've done a few you can then come in
with a pair pliers and neaten things up
a little bit you can pull and then push
on the weave like
that and this will tighten up the weave
and then you come in with a f pliers
press it down slightly and now now they
sit nice and flat so we can continue
with the
weave like
that so we're going to
do maybe five to start
with and also we're going to do we're
going to do five on this side and then
obviously we're going to move
across and we're going to do the same
thing on the other side so this time
because we're on the other side we're
going to do
the closed side because we flipped the
pendant so the closed side is on the
bottom you bring down your wires
closer make a little Bend in it just so
that it's
closer and then two wraps around
both and
then we're going to continue with one
wrap around the top wire one
two
three and so fourth and obviously we're
going to be doing
that on both sides and then neeting
everything up what I always do is when I
finish is just bring the the weav in a
little bit and press and tuag until
everything is nice neat all right so
I've now finished the weaves I've done
11 um be in mind that if your stone is
bigger or smaller than mine this will
obviously change um so we're going to do
next is bring our Stone in we're going
to place
it a little Gap and that already gives
it a little bit of security we're going
to shape these The Weave on this we're
going to do the same on both sides I'm
going to show you on the one and then
you can see what to do so you want to
make sure that the stone is seated in
the position that you want to be it like
that
and we're going to shapee
this I want to capture the tip of it
like that so you want to make sure the
stone is held in place but you don't
want to hide too much of it um and the
legs of this actually need to go through
so I shape this
first and then I bring the
legs through the
frame like that
wiggle it a little
bit you can lift the stone up obviously
later on the other side this is not an
option so I tend to keep my finger on it
and keep it in place
anyway I'm just going to remove it for
now there we go so that's easier like
that so now you want to line this
up I I prefer to keep the stone in place
because it helps me for me anyway I like
to keep it there so that I can shape the
weave as I attach
it so bring this
through and pull this tight against the
stone like
that and that will hold it at the base
here and then we're going to be
attaching these
wires to the frame
like
that again you can just wiggle it a bit
to bring it
through pulling the wrong
way right there you
go was it I think I'm going blind even
more cuz I can't really see where that
my usually when I work I have a ring
light I can't really do this when I'm
doing the video so I can't really see
what I'm doing right so that's one
attached and I'll do one more Loop
because we want to just make sure see
this is why we left a little Gap a tiny
Gap just big enough for the wires to go
through the frame and if you haven't
that's fine you can just take the stone
out and adjust it a little bit to make
sure that this actually fits in so it's
no problem if you haven't done that you
know from the start right so that's one
attached and we're going to be attaching
the other
also like
that same thing bring it
through and kind of wiggle
it like that and do two but yeah you get
the G and press it together so that is
half of the weaving Stone obviously
we're going to be doing the other side
so I'm going to do that um and then
we're going to do the next set of wires
so that's what we've got at the
moment right so I have now attached both
sides so now if you're not happy with
the shape right so like this one is a
little bit higher than this one you can
come in with your pair pliers and you
can manipulate this so if I want to sit
high up I can just bring these pliers in
and shape it a little bit with that if I
don't like it I can push it down and if
I want to bring this weave down for
instance I can use the leverage here to
pull this weave down a little bit and
that way I can adjust obviously just be
very
gentle um with the wire because pressing
on these wires will damage the weaving
wires cuz they're very delicate so you
need to be very careful in doing that um
but yeah you can do that so just until
you're happy with the Symmetry with how
it looks and the shape and whatnot um
and yeah so now we're going to be using
we going to finish up I'm going to TI
this up a little bit and then we are
going to um use these wires here to do
something with um and I'm going to bring
this across to the top um but at the
moment it is already half secured with
the weave that we've put at the bottom
but we obviously need to you know do
something at the top so that's what
we've got at the moment all right so
have now attached everything and I've
shaped it the way I wanted to and now
we're going to be using these wires here
and I think I've Twisted this one a
little bit so we kind of straighten that
up so that it's not going to look a bit
strange when we're trying to weave it so
that's the problem with square
wire can
sometimes
twist right so we're going to do the
same thing again so it is three wraps
around we're going to just use the
remaining wire from The Weave so just
bring it down we're going to attach it
here so it's three wraps around the
bottom wire and then two wraps around
both and again we're going to be doing
this on both sides so
three and then two
and so forth and we're going to be I'm
not sure how many probably going to be
doing about six or seven but we'll see
just now and we're going to be doing
this on the other side as well so do
that and then we'll come back and do the
next next step right so I've created
about 14 or 15 rows um of the sque but
obviously as before you know fits
different for you um so your Stones
Bigger you may need to do more or
less right so we're going to do is we're
going to shape this and to lay over the
stone and then follow the shape of the
stone so the way I do this kind of twist
it and lay it over my
thumb and
[Music]
create a little
swirl to go up like
that and then we want
it to
go I think we're going to lay
it going to bring the these legs
[Music]
through and then we're going
to attach
it to the frame just
here think you need to kind of
straighten it up sometimes the weave
likes to not sit the way you want it to
so I kind of Twisted
it I want it
to set up and then go through the
frame so that we can attach
it like that so now obviously the weave
is not the way I wanted to but we can
sort that out later so the most
important thing is at the moment to
attach the weave to the
frame you can manipulate the way this
sits at a later stage so as before we're
just going to find a spot where you have
a bit of
space bring this away and then just
wrap the
leg around the
frame like
that bring it down and do the same
should actually go and do it twice but
don't know if there's enough space I'm
going to do one for
now and then we're going to do the other
like
so because there's in my case here there
isn't enough space so that's that so
now we've attached this we can try and
manipulate the
sweave a little
bit so you can see it's setting up here
so you want to bring it
down so very
gently press
it like that
you can bring it up here and shape it
with your with your
tool and I want it to follow the
curvature of the
stone kind of like that you can kind of
just manipulate it and press it into
place as it work so we're going to do
the same on the other side and all right
so that's what we've got at the moment
so next I'm going to lay down some
detail wire and I kind of like to use
wires that are already in a design um I
just think it adds a nice little touch
so I'm going to do is take the lowest
wire the square wire and I'm going to
just make it
follow the lines that are already there
I'm pressing it in and then I'm going to
bring it
out here
you just kind of press it in line and
that just adds a little bit of detail
and it also helps the stone to stay
seated like that and then we're going
to attach you're going to be a little
bit crowded here cuz there isn't much
space that's fine we're not going to add
any
more you won't see that as well cuz
we're going to hide it so then we're
going to tie it
off and that's what we've got at the
moment obviously we'll do the same on
the other side or realized I think I've
broke the wire there so anyway but you
still have one there um and you're going
to do what I've just done um if it so
happens that one of your wires is broken
like I did here you can all you can do
is just find a spot here cut a new piece
of wire and add it in um and then you'll
be fine so just you know add it in and
then do the same thing and bring it up
here and that's that so that's what
we've got right so that's what we've got
um I've got one less here cuz I didn't
add one in so we're just not going to be
using the one on the bottom we'll cut
that off um so what we're going to do is
cut a piece of 1.5 M of 0.3 mm
wire and we're going to take this wire
and we're going to be adding it in half
on the left and half on the right and
we're just going to be
starting uh some more
2x3 so as before it's three
around Bott
botom
and then two round both wires like that
and you're just going to have to work
your
way around and I just need to bring up
pliers cuz I like to scoot them up but
you get the idea so we're going to
create a few sets here and a few sets
there I will tell you how many sets on
each side uh once I have put them
together so I'll do that and then I'll
be back in a sec all right so I have
made 10 on each side so again just like
we have done with the other weave we're
just going to bring this and kind of
shape it and I
want I want it
to follow so we need to make it
straight so you need to kind of twist it
so that it
stays
flat and then
bring it
across and I think I'm just going
to attach it
here so that's what we've got at the
moment I'm going to do the same on the
other side and we're going to keep one
here and then
attach the other Theo because that's
about as much space as we've got we
really don't have any more space after
this to attach any wires
there so I'm
just going to feed that
through and then
attach this
wire to the side and that that weave
here will hide any little sins here that
you've committed ulio anything that's
not quite straight um and obviously
we're going to be doing the same on the
other side um and then we've got all
these wires to work away so just tighten
that up a little bit you can wrap that
twice if you want to not really
necessary but it makes everything a
little bit more sturdy so that's what
we've got at the
moment show you from the back little bit
messy we can fix that up straighten
things out right right so now I've
brought I've wrapped these around twice
uh and now we're going to cut them off
you want to cut them off
somewhere in the middle like that is
just to prevent
them
from um snagging it on anything so then
once we've done that you can tuck them
behind the Weaver so so just
up like
that and just kind of tuck them out of
the way we'll need to leave enough space
later on I don't know if I'm going to
add Stone in that or a bead I don't know
yet so just make sure you got a bit of
space so that's that um and now we need
to think about creating something at the
top so I'm going to have a look at that
and then I'll be back that's what we've
got at the
moment right so I've decided that I'll
add some beads to this so you can either
use some of the uh
0.622 gaate Square wire to add the bead
surprisingly even the time iest 2 mm 1.5
Ms actually go on that um or else you
can just use some of your weaving wire
to do that but I prefer to you know use
some thicker base wires cuz that you
know hasn't got doesn't break so easily
the only drawback at the moment is
obviously once we do that that now we
have to find an extra
space for this wire to attach some way
and I think I'm probably just going to
go around the base of the Bell like
that um so just going to make sure it
fits sits exactly where I wanted to
be just need to bring the beads
down like
that and then just arrange
it press it into
place and then just kind of attach it I
need to fix this up a little bit cuz it
looks messy but then what you're going
to do is just wrap it around the base so
bring it round like
that and I like to use my tools for that
makes it easier hold it in place and
then just wrap it around
twice and that will give you a nice
attachment point and even if you're not
happy with it in the beginning don't
tighten it up too much you can then just
come in and adjust the bead and then
tighten it all up again so obviously
make it look nice and since I've broken
the wire here I'm going to have to add
one in um but I'll fix that up that's
what we've got at the
moment right so I've created weaves on
each
side so we're going to do with this now
is exactly the same as we've done with
all the others and we're going to
sweep the weave
round and then bend these
upwards and just leave enough space so
that we can add a stone in here
later so bring that around and then
we're going to
take these wires we need to bring them
in up so that we can attach them towards
the back of the Bell so SLE around with
the shape a little bit like that that
until you're
happy and then we're going to bring
these wires
around and
attach to the Bell like
that I'm going to do the same with the
other
wire bring that
through like that
and just
follow the shape like that so then it
gets it lays against the bail like that
and then obviously wrap it around a
couple of
times now with the other weave obviously
you need to
travel to Behind These wires here but
it's the same concept and then once
you've attached them you can come in and
kind of play around with the shape a
little bit like that make them rounder
and just overall more symmetrical so
that this side matches the other side so
I'm going to go and do this side attach
it off and that's what we've got at the
moment all right so I've attached these
so we've got them laying over the top
and then if you don't like the shape of
them you can then come in and use your
pliers to ever so gently move them into
position and squeeze them together here
like that until you're happy so this is
a little bit unsightly here so if you
wanted to you could bring this in here I
don't know how it's going to look but
I'm going to try anyway it maybe create
a little
swirl just to
hide to sort of unsightly bits you're
probably going to need to cut this off a
little bit
more make it
shorter this is just an idea it might
not might look like a dog's breakfast
but I'll try anyway
so squeeze the
end and then just roll it in a little
bit yeah I don't think that looks nice
so I think we'll just cut that off put
maybe some beads there cuz it Doesn't
travel right so I'm going to do bring it
round and cut all of these wires off and
then tuck them
away underneath like
that come in here and you're just going
to have to try and arrange it and make
it look as neat and tidy as
possible so that's what we've got at the
moment and then we've got these two
wires left here I'm always some of you
might know if you've been following me
for while I hate cutting off any wires
um but I think we're not going to be
doing anything with these so what we're
going to do is just come in and again
going to trim these off
that actually we could just no no we
going and trim them off otherwise this
is the thing when you have all these
wires sitting and you're going to
reattach them and bring them up and use
them for something
else and then you end up with so many
layers that there's no space and that's
how the designs become busy because I
keep adding new
stuff right so that's what we've got and
now we can concentrate on um adding some
Accents in there so we're going to do I
think these ones we're probably going to
cut these off as well don't know why
I've kept them sometimes I like to use
these thicker
wires um to hammer um and create a
flared shape but I think for this one we
probably won't and we're just going to
cut them off um so that's what we've got
at the
moment okay so I've trimmed most of the
wires off so we're going to do I should
have cut these off in the beginning cuz
we're not actually going to use them but
as I said earlier I I just never know if
I am going to use them so I left them in
we're going to leave one of the weaving
wires because we're going to use it to
stitch in some beads so I'm going to do
is just come in here and you want to
trim off these wires obviously as
before as close to the inside as
possible to avoid any possible snag
risks um and then obviously flatten that
out to have the space later on to
add a
stone just make sure so you're going to
do the same thing so I'm going to cut
that off just now as well but the last
step or the second last step is to come
in we're going to take this weaving wire
that we have here the
leftover and we're going to be using
this to stitch beads in place wherever
you want them like I think here might be
quite nice to have like a 3 mm bead
bead so what I'm going to do
is add the bead to my
wire like so and then just kind of find
a spot where you like the look of the
bead like this so what I tend to do is
take a bead add it in you might not
necessarily like the speed where it is
right now and I kind of make my way
down to the next spot in the this is
just sort of very generic you're going
to have to do it much neater and
obviously you know choose the attachment
points carefully because you want the
wires to be hidden as much as possible
so when you do come down kind of try and
go in areas WRA it around a couple of
times and then if you struggle to open
up a space like I am right now what I
tend to do is bring in a
needle and kind of wiggle it a little
bit so that creates an
opening and it'll come
through and it'll let you bring the wire
through because obviously the needle is
roughly the same thickness as the wire
so obvious this is not very tidy so
you'll find spaces where it looks tidy
but now you're down here and you can
then bring in another bead if that's
where you wanted to go
and we go through the the center
here
that and pull it tight obviously these
wires snag at some point but yeah you
get the gist so this is what you do with
the weey wire that's that's why I tend
to keep these wires attached so I don't
have to add in more the more WI you add
in the more snag risks um so I try and
use one wire Stitch the beads in all the
way around come back to the top and then
cut it off and then last but not least
we have a stone setting so this is some
point 6 mm wire with a 5 mm Stone just a
prong setting I'll pop a link to the
video on how to make these settings and
all we're going to do is just pop this
through where you want the stone to sit
and put it in place like that and then
obviously use the legs of the setting
and attach it find a space where it's
safe and wrap it a couple of times until
it's nice and
secure as well before you add in any
Stones if you want to oxidize your piece
put it into the solution polish it off
because some gemstones really don't do
well in in the L solution uh more
specifically the porest stones these
ones will be fine because they are low
to lights they don't absorb any of that
chemical easily or liquid so that'll
work so I'll do that and I'll show you
the final
result that's the pendant done thank you
so much for watching I really hope you
enjoyed this if you haven't already hit
the Subscribe button because I upload
new stuff on a regular basis if you feel
like joining our artist community on
Facebook I will pop a link to the group
below we're a Fun Bunch so feel free to
come and join us I also have social
media if you want to follow some short
stories that I put up occasionally and
I've got Facebook Tik Tok Instagram
Pinterest and obviously YouTube and also
link is below and last but not least
visit my shop if you're interested in
getting some kits for these tutorials
gemstones beads wire um and all sorts of
other things so as before there is a
link to all of that in the description
below and that's it for me hope to see
you next time bye
e
e e