The Shunt Resistor And Bad Tubes! - 1953 G.E. 17t5 TV Repair #6

Amateur Repair Time
257 followers
78 Video Views·Oct 11, 2026
Check out our Patreon page, for all of our channels. Contains outakes, concise arcade repair tips, bloopers, repair FAILS, Audio youtube wouldn't allow us to upload, and much more!
https://patreon.com/JoesClassicVideoGames
------------------------------------------------------------------------------------
Ladies and gentlemen, welcome back to Amateur Repair Time.
We have been working through
this General Electric 17T5 television set.
And we've been going through section by section by section.
And we finally got it coming up with a really horrible picture.
But it is actually receiving a video signal right now.
And that's actually the audio tone
of this generator that you're hearing.
Let me turn down the volume and I'll show you.
So that's not like a feedback or a squeal.
that's like the actual um tone that i'm giving it
right um and this screen this image that you're
seeing is what's supposed to be going on uh
of the crosshatch signal it's just we're we can't get the
brightness right so basically it's way too bright i can't turn
the brightness down to the point that
we can get a good picture we've
also got problems with horizontal hold and all of that but i can't
tell really what's going on because we don't have
a good picture on it yet so what we've been doing
if you didn't catch the earlier videos now remember
this is amateur repair time i am not a television
repair expert we've been reading this practical radio
and television mail order tv repair course
that once belonged to mr w
e rains jr that i bought at the flea market for five bucks
and it was put out by the national radio institute
this is 1950 1951 um this television set is from
1953 so what we've been doing is going through
and reading uh the section that's pertinent to
the television just to kind of get an overview of it
and hopefully understand it a little bit
and um then going through
and working on that section replacing the capacitors things like
that testing all the resistors
and we've had a lot of fun if you didn't watch the other videos
you missed out so much um so basically
in the set there are i think i guess i think i thought
seven sections um now i do have a history of working
on arcade monitors which are CRT monitors
but they're they're solid state i guess you would call it
so they're not like this this is a tube
driven chassis analog how would you call that they're
not i guess solid state right what would
you what would you call it before solid state
so there is a power supply section and it's mainly
the B plus section we messed with that got it right
in my opinion right uh and then in also
the power supply uh it shows this the series string
um of all of the tubes there's actually
two of them in parallel
but we work through all that now we have not tested all the tubes
all of we're going to do that soon in this video all
of the tubes are yeah kind of working because
the filaments are working
because all of the filament strings are working okay so there is
a power supply this is it
and we checked that we we read about that a little bit in our repair
course here and we did a whole video on that okay
then we moved on to the that's upside down
we moved on to the horizontal section which you
know creates the horizontal sweep and we worked
through it all the way up to the flyback
and beyond and then we figured out that we didn't
have high voltage but that was one video
so then in another video we did the vertical sweep we
worked through that all the way through
and in each of these videos we're reading the pertinent
section in this manual uh this repair series we did the vertical sweep
and on that video uh
i think we also repaired the high voltage
and figured that out got the high voltage going again
okay and then
in the previous video uh we went through
the rf section so the antenna section
so we have this encoder plugged in straight through
the antenna section uh on that we figured
out that there's not a lot that you can test easily
because a lot of the resistors have to
be removed from circuit to test there were uh there
was a little bit of stuff we could test
but we didn't really replace a lot because it's all mica
and things like that we did have one
mica cap that we broke in there in the horizontal section
and we replaced it with a with a
replacement vintage mica cap okay
and we tested at the very beginning we tested the tubes in the
horizontal section we haven't done any of the other ones yet
though so we're going to do that
soon okay so but our problem now appears
to be that the brightness will not turn down i'm used
to on the arcade games at least that you can turn it black
with the brightness knob um and you know
on ours they have a screen control usually on the flyback
so with the screen control certainly you
can turn it black and then with the brightness
control i guess you know if the screen control
is set right sometimes you can't turn it all
the way black with with the brightness control
so anyway but the whole deal is this we know
the signal's coming in the video section but
we haven't done anything in the video IF section
or the audio IF section um so i'm thinking we
might have a problem right where it goes through the converter
and again we haven't tested all
those tubes obviously we're getting a little bit
of video IF i turn off the cross hatch you see the
screen change and you we are getting audio
although it's very weak um so the signal's
getting through it's just not getting through
the way we want it to get through we also haven't
done the sync section so that's power supply
horizontal vertical RF video audio and sync IF
you count sync really
so and then you could count high voltage as a separate one too but
so there's seven or eight sections in it
um we don't have the ability to test the picture tube
with the tube tester although obviously you can tell
that the thing is at least pretty much working
now here is the brightness control um you know i put
a check mark there but i don't remember if i
was checking that one meg resistor i think i
was but i have not replaced that capacitor right off
of it so we might need to do that and check
the the value of the brightness control i mean i
wouldn't imagine that's changed much
and then that resistor there i i don't see though hmm you know
if that well hmm i don't unless it works backwards
than what i think it looks like they are varying
it from 235 volts to ground
or B minus that you see the B minus connection there so depending on
where the control is set it's either at ground
or it's at 235 volts and then it runs through that
resistor uh so our our hmm oh
the cap goes to ground so if the
cap is shorting then that line
would be closer to ground i wouldn't think
that the brightness worked that way i would think that
it would work backwards like if it's up to 235 it would
the screen would be brighter but if it's set
up like some kind of bias then the higher
the voltage the darker the screen yeah so if that
cap is dropping the voltage down to you know closer to zero
or if that cap's even shorted
then it would make it or pretty much shorted it
would make it where it's brighter but i don't
know if the brightness works that way so when i
when you turn the brightness control to ground
is that going to make the screen brighter
because you're losing a bias voltage you know on the on
the tube you've got the high voltage you've got
the b plus voltage you've got the filament voltage
i mean you've got several of them you've got
the grid voltage whatever okay so how are we going to
figure this out well first i'm going to swap that cap
that's the first thing i'm going to do just to
see if that fixes it okay another thing
is like i said we got to replace the tubes we got to check
the tubes this one tube glows really bright
which i thought well it's probably just that particular
tubes made like that but no it's really bright you saw it right
that's one of the tubes in the
IF section I mean the RF section
so it could be that that tube is just causing us all
kinds of problems and putting all kinds of noise
into the signal of the audio and the video and
that's why we're getting that crazy thing
but i wouldn't i wouldn't think that you could overdrive
the video signal and make the screen where you can't turn it down
to black that doesn't seem
like that would be a thing to me
but i don't know how touchy the brightness circuit was on these old
tvs now some of you are watching this video
and you're going oh this guy won't he just start
working i like to think things through
and that way i learn so like it would be interesting for
me to learn if the brightness control
the way it's set up if turning it to ground makes the
screen brighter or does that make it darker right
because then that would help me understand that
circuit and in the future if i saw
when it's too bright i would know what the problem is
you know if that even has anything
to do with it it's possible that if any of these voltages get
off that your screen will be too bright
so um so how am i going to figure it out well like i said
i'm gonna look at that cap first
and then look what else i found i was at the antique mall the
other day and i walked by and i actually
was reading the names of the books as i went by and
there's thousands of books, and I found this freaking book,
Practical Color TV Servicing
Techniques. Now, I've got a couple more, I think,
around too, but I've had this for a few months,
but I just saw this, and then right underneath it,
TV Servicing Guidebook Problems and Solutions,
and then right underneath it, TV Troubleshooters Handbook.
These damn books were sitting on the
shelf like this with a pair of shoes on top of it,
and they just had them there because they're red,
and then over here, there were some green ones,
and over here, there were some blue ones,
and i saw it like i think i saw this one it said tv
and i went what huh what's the odds of that
and so of course i bought them on now luckily here's
the good part three dollars and 99 cents
each and this one here looks really good
um so a couple of these actually mention uh if there's
problems with the set like especially this one
if there's problems with the set this is what it
might be and this one's even got it sorted out
by the different manufacturers so i'm going to
browse through these i'm going to peruse
these really quick to see if they're somewhere where
it mentions the brightness i'm also going to look in here
and find the section where it talks about
how the brightness is controlled
and we'll see if we can figure that out so that's our next step
okay so this is our schematic
and i'm reading through this this is from 53 this is from 51
i'm reading through this and they're showing some examples
and they show this example which
is similar so we've got a a a potentiometer here
on one side is the b plus on the other side they
have an extra resistor but on the other side is b minus
and they are showing this as it mentions in
here that you need that so that you can't turn it all
the way to zero because it might cause
problems blah blah blah let's read
this for a second brilliancy control and at first when i
read that i was like brilliancy is that the right one
is that brightness the picture tube must have
initial bias that will set its operation
at the proper point on the brilliancy grid voltage curve
the operating point is set at the point
of greatest curvature as at point x in figure 27
this point then represents the black level
at which the pedestals line up the video signal
swings the grid towards zero the video signal swings
the grid towards zero to give increase in
brilliancy and the sync signals make it more negative
so that the screen is blanked completely
during the sweep retraces okay well it looks
like we've got sync problems obviously right
so they're saying that the sync signal
and the video signal are absolutely involved in brightness
because it has to do with setting the bias level
of where black even is so on ours if i turn the
brightness knob it does darken like it does go brighter
and darker but just barely probably
because we're way up here somewhere let us momentarily assume
that we can couple the signal
so it gets over our head here for a second
or over my head let us momentarily assume that we
can couple the signal to the picture
tube through a coupling condenser c17
no c17 as shown in figures
27b and 27c okay uh the signal
and ours is so ours
is coupled through c53
right there this is our
video signal this one up here i think that's
the focus voltage maybe possibly as shown in figures
27c we'll focus on because ours is like yeah
so there's our video signal coming in there is a
resistor from the video signal to b minus let's
see if that's correct that is correct so you know
b minus is b minus right
so it's there is a resistor from the video signal to b minus that
is that okay the initial brilliancy bias must
then be obtained from the power supply the variable
bias control resistor r2 in both
those figures brightness well
we think brightness can be used
to adjust the bias to cause operation
at the proper point on the curve the fixed resistor r3
is added to prevent the setting from ever being
reduced to zero this is necessary because the
tube might be ruined by the excessive current flow
if the bias became zero for very long okay well
if we look at this the way they've handled
that i suppose is with that resistor because if we
turn that to zero where that's ground this isn't ground
because there's still a 220k resistor in
place right so it's 220k above ground
the fixed resistor r3 is added
to prevent the setting from
ever being reduced to zero this is necessary
because the tube might be ruined by the excessive
current flow if the bias becomes zero
for very long since any change in the setting of the
variable bias control changes the average average brilliancy
of the scene by moving the black level
it is known as the brilliancy control
and so when i'm reading this i'm thinking oh well this might
not be the right thing if the brilliancy control is set
so that the bias is not sufficiently
negative the overall picture will be light
so basically we are adjusting the voltage as control
as compared to the video voltage and as compared
to the sync voltage the retrace lines can be seen
if the control is far enough from the proper
setting we don't see retrace lines but it's
getting close if the control is set
so that the operating point is too far in the negative
direction the darker portions of the scene will
be telescoped together with the result that some
portions that should be gray will be black
on some sets the brilliancy control is a screwdriver
adjustment on most however it is operated by a front panel knob
so that the set owner may adjust
the brightness of the picture to a level that suits them
so the brightness control on ours
is this control that they're talking about
so um of course the dc restorer which we will still
study later would be needed in circuits like those in figures 27c
however these are the basic
methods used in ac amplifiers for getting
the initial bias for the picture tube the absence of
a coupling condenser in a dc amplifier means
that the drop in the load of the last video stage will
affect the bias of the picture tube thus
in the direct coupled system the initial bias the bias
when no signal is being received is obtained
from the dc voltage drop across r7 as shown in figure
28a similar the drop
across this resistor
is determined by the plate
current of VT2 with
usable current load values this drop is normally more than
is wanted if the circuits in figure 23
and 28 therefore there is a control in the cathode circuit
of the picture tube that makes it possible
to apply a bucking voltage that will reduce the bias
when the slider on R9 is all the way to the
left figure 28a the bias is that across R7 alone
however when the slider is moved more towards the
right a voltage of opposite polarity is added between
the cathode and grid of the picture tube
thus reducing the bias okay
so yeah in other words absolutely
if there's a problem in the
video section it could absolutely make it too bright
and if there is uh even a problem in the
sync section it looks like maybe it can make it too bright
and it says that the sync pushes the
voltage lower which would increase the bias
but i still didn't figure out if that means it was
going to make it brighter
or darker um i don't know i'll have to i'll have to keep looking i
looked in the other two manuals that were on or the two books
that were on black and white sets
and they didn't mention anything specific about uh
that they did mention that you could have a
shorted tube i've seen shorted tubes on my arcade monitors
a lot actually um but that doesn't look
shorted to me it just looks too bright
so all that to say i think we need to test the tubes
and we need to work through
the video section i think what i'll do is test the tubes first
because then if we find one that's really bad i'll know
when we're working through the video
section to focus on just that area
and make sure that we don't have a bunch of burn up resistors
in that area but i'm going to look at all the resistors anyways
and also it's dying i'm dying
to see if this um rf tube here is bad
or not because of the way it's glowing so let's do
tubes next and then we'll work through uh the video if section okay
so on the on the previous
videos we did the uh horizontal sweep tubes
and we did the horizontal output the damper tube or
whatever that's called high voltage rectifier
the damper tube the horizontal output tube so we did
the horizontal stuff so now i'm moving on to the vertical
which was the next stuff that we did we
did not do the sync section yet it's small
though one tube and some caps and resistors
okay so i should have done these next
so the next one up is a 12sn7gt it's the vertical blanking
and the vertical uh multi i don't even know
what multiplier vertical multiplier um and it's
the vertical hold control and the height control
now i haven't seen it we're always off the screen
it seems like too so this tube apparently
is all screwed up now i'll point out that it's a raytheon
i've just watched a video a while back of shango talking
with a guy named al who was just like an
expert on tubes and he didn't have a lot of good things
to say about raytheon he said that raytheon
made good tubes back in the day
but that a lot of the later raytheon tubes were just junk um and
this is a raytheon it doesn't necessarily mean
that this wasn't a good tube at one point maybe
it just uh it's just old or something right
but it doesn't look good so there's no shorts there's
no problem with grid emission but here's
our test i mean come on now let's check the other side of
it yes see okay so here's
the other side of it i don't know
if the shorts are the i guess the
grid emission still could have a problem okay let's see what
this side test says also horrible
okay so it would be interesting if that tube was part
of the problem so it's a 12 sn7 gt let me see
if i can find that okay so i found an old ge one
and if i test the first side we get a question
mark however if i test the second side it's
similarly weak i wonder if these things just
burn up a lot i had someone tell me on videos a couple years ago uh oh
because i was working on
a bunch of radios at the time oh you know those radios
are much more forgiving they'll just take
any crappy tube but on a tv the tube's got to be perfect
and he was basically saying that because
he is a debbie downer
and he's a he's a trying to discourage me i guess from working on tvs
and i've got thousands of tubes i mean i have tons
of tubes that i picked up over the years
largely because people don't want tv tubes
and this is one of the most common ones probably
but it'll be interesting to see if the guy had
a point like if i find one that tests really good
and i put it in there we're going to test it after just that one tube
and we'll see if that fixes the
whole thing i mean it won't fix the whole thing
but we'll see if it makes a dramatic improvement
that would be pretty impressive okay
so i tested three different ones one had a short one was just
as weak as the other one and one was just a little bit better
but i've got this new old stock one
here and it just happens to be a ge
which is you know pretty cool to put back in a ge set so let's
see what's going on with the new old stock one
the shorts no gassy emission leak oh yeah i like
that okay let's try the other side
no shorts no gassy emission
leak folks i think we found our
tube okay so what i'm gonna do is i'm gonna put
that tube in and i'm gonna hook the signal
generator right back up to it
and see if we get something different okay so this overlapping on
the top there's some kind of adjustment
on the back i gotta mess with that some more but if i
turned the vertical now i do get a difference
in you know obviously something's working better
than it did before before i couldn't do that at all
and then this is the horizontal i can't quite
get the sink in so the only other uh tube
in vertical is the vertical well it's the vertical
amp 12au7 also a raytheon oh hell
look at that it's got a short
in it grid emission problems
like a heck okay so uh let's test there's two sides
to it let's test one that's good one and
two test good but the gritty mission
if that needle moves you got problems and usually if it
so like you can have a short
and usually like the light will come on but if you have a grid
mission problem uh when you hit short it'll swing
and then gritty mission will always also swing
yeah so that tube's probably actually bad
so let me see if i can find a 12au7 all right i was
fortunate enough to have another new old stock one
no shorts we don't have the weird grid emission
thing going on that the other one did
and both sides test good it's also a GE so i'm going to
slide that in there and then we'll turn it back
on and see if that changed anything you can see
how it warms up maybe it'll give
us something interesting
a little different
that changed
anything but hey
so i think that's brightness up that's
brightness down one maybe contrast or
something or picture or whatever okay
so next up that little sucker okay so this is the first RF
amp in the RF section so this was the next thing
that we moved on to it's a 6ab4 i would like to
find another one just
so i can see if they all glow crazy like
that oh look it is not what have
i got it in the right
place let me see here what
in the world's going
no short, no short, so is
the glowing because it's burnt slap out yeah
because there's no the the uh the filaments you
know normal in the tester but we don't have huh
well what in the world could be doing that maybe
just because it's tested under load
and it's not um oh A25 oh that's going to be an adjustment
right it looks like a variable capacitor
A25 let's see what that is here's our handy dandy list
okay it's the dial right behind it yeah i think
they're just saying that's like an alignment
adjustment hmm well what
do you think about that folks
so a13 there as well got
a cap there i
wonder if one of those mica caps is shorted
that could be our whole problem okay let me see if i
can find another 6AB4
and we'll try swapping it in and see if we get something different
i don't have a capacitance meter here that that's going
to be able to test these little mica caps
and it's kind of hard to test them in circuit anyway
because they're across you know things
like a transformer which is basically a short
and you just the way it's all designed you can't test
very well on in this RF section plus it's very hard
to get to everything under there it's all
on top of everything see this resistor here how it's across a choke
or whatever an inductor so
you can't test those in circuit you have
to remove every one of those to test them
plus are we really going to get a lot of wear
on on those resistors there they're not power
resistors or anything um closed on low band
okay yeah let me see if i can find another 6ab4
we'll test it on this uh i mean this is obviously telling me
that it's not testing i mean that's
what we got it's dead as hell and we can kind of tell
because it's so burnt up whatever it's on
uh so let's try another one
and see if the next one we pop another one in and it glows just as
bright then we know there's something in that circuit
that's frying it i wonder if it could be
the second amp has a short in it or something
and it's drawing so much current through that
that it's screwing that one up i don't know let me
find another one okay so fortunately i did have a
6ab4 a dumont uh tested it it tested perfect okay put it
in turn the tv on it immediately
started glowing too bright again
so i'm wondering if there's like a short in that socket or
something i don't know you know since it's
a series string it shouldn't work like that okay
so i moved on to the next one just for giggles
which is a 6bc5 and sure enough the damn thing
she got a short in it or grid emission problems one
or the other so i wonder if that is somehow
interfering the previous tube
and causing all the problems
and i wonder if it's killed this
cap here two point three point
three picofarad um so yeah i mean
the filament you know they all
should be separate even if that one was touching
that socket you'd think it would cause a problem
with all kinds of stuff but we've definitely got a bad tube here
so let me try substituting in a
different tube there and then we'll turn it back
on and see if it still makes this one too bright
aha i figured it out so i'll bet a bunch of you
that really know your stuff you've probably been
telling me this for like three videos
but thing is i film these videos in advance like i'm way
ahead so a lot of times people get very frustrated
because they tell me something and then the next
video i don't address it it's
because i already filmed those videos and they're done i like just
kind of figuring the stuff out as i go along i feel like i learn
a lot more that way okay so i have found
the issue it took a while but i have found the issue
so i started thinking why in the world is
this one glowing more than
the other one something something don't make sense right uh some of you
probably knew in the very first video
as soon as we powered it up so there's not much to it
really but the issue is it's buried i mean it's
freaking buried you can't take this off i mean
if you if you try to take that off nightmare scenario right
so you can't get to most of the
stuff so this is our socket up here so i started looking at it
and i'm looking at it and so there's
pin one and you know i check and okay everything
that's supposed to be on pin one appears to be
there and again you cannot check the stuff
because for instance there's this resistor
it says it's supposed to be a 3900 ohm
but it connects into the middle of the the tuning
thing which is all connected together
so if you check that resistor it's zero ohm because you're
just connecting across a dead short um so you could cut it loose
but it's not even the right
value anyway i mean that looks like a 47 to me it's
this one right here okay so anyway i'm poking
through it and poking through it and poking through it
and i'm trying to find the pins that
are the filament because it looks like it's got something crazy going
on on the filament right
well it's these pins right here obviously
so if you come down here it is the first rf so it's this
tube here and like most tubes it's the the filament pins
are four and three okay so uh on pin three
there is a capacitor there
that they've got tied basically
to b minus right so that is this cap
here this one here goes in it as well
so i'm checking it and it's almost measuring with
shorted depending on what you do so i take the tube out
and then i take the other tube out so i
took this tube out and this tube out um and now this pin no longer
or this cap no longer connects
to ground so there's something going
on so but if you look you're basically just measuring the
resistance through a couple more tubes
and uh you know if this one's like three ohm three ohm and
this one's two ohm or something
or whatever it is it's like seven ohms from here to b minus so i
took these out and those do not measure shorted okay
and then look at this little baby there is
a damn resistor across the filament of that particular tube
and they have added these
capacitors right on that particular tube so that's
going to do some craziness um and that resistor
might be an issue right well if you look
so i'm like well where is that resistor man i can't see
it oh it's got to be under somewhere pin three
and pin four these led lights are they suck but
there is a white wire around resistor right back there
and that's it and that some that some sucker
is open so they have purposely put
a filament shunt resistor across the windings of that tube
and that thing has opened which is why that tube's glowing
so crazy huh ain't that something so i need
a 43 ohm four watt resistor
so when i ordered the power resistors i looked through this and just
looked at any of them that were big
right just in case and um this one
is r29 it's supposed to be a
43 ohm four watt resistor and since
when i looked through it was a four watt resistor i went ahead
and ordered one now i got a 47 but that'll be all right
so i actually have one i just didn't know
what it was for um kind of tricky to get back in there
but there is actually it's hard to see but
there is actually a tie strip in there
and so i think i can fish through there and get that thing
back so i think that might fix our whole problem with the video okay
so there's no way i could get
back in there so what i did was i found
the two tie points on the terminal strip that uh it was
originally attached to so i attached the resistor
to the one that i could get to the one that was
over here the resistor just broke loose um and there's no extra pigtail
or anything i cut the
extra pigtail off here so that there's nothing hanging
and then i flew it i've got a zip tie
here to hold it so it can't move
and i put spaghetti on it of course i flew a new wire over
to here which is actually this tie point oh i'm
sorry this tie point so pin four i can't get to
that point but i've got the resistor going to there okay
and that and that are still connected
and then this one is where i could get to it
so it's actually reattached so we're good so let's
fire the thing back up and see if that uh see
if and i'm putting in a new old stock tube because
we fried the other one because the shunt resistor
was burnt up let's see if it if it quiets that
down a little bit now that is more like it
so the tube looks fine we crt has not warmed up yet
like i can hear
the audio we
have still got
our same video
issue though
so we need
to move on
into the vertical sec i mean the video section
which is what i claimed we were going to do in
this video but we uh we fixed the problem
of the glowing tube we had the one tube that was a super
glower and uh we fixed that it didn't really improve anything
but obviously we weren't going
to get the video signal through with that bad
so we probably got more tubes bad in the video section
and I haven't done any of the resistors in that section.
But I think we've made some real progress
figuring out why that one tube was going nuts.
It's the shunt resistor, folks. So the next time
I look at a series string tube set,
I'll know that it's the shunt resistor when I see that
on the schematic.
So these two that I'm adjusting are vertical
and horizontal hold. And yes, I know
on some sets you can't touch the metal knobs,
but this is not like that. All right, I just can't
quite get it we haven't done the sink yet either
so we still got ways to go but i think we're
getting there and we don't have to worry about it frying
our tubes anymore or at least those tubes
it might fry some of the other ones like
that third one that we haven't tested yet but i think
this is a good stopping point since we figured something out
so leave your comments below let
me know what you think i think we've done six videos on this thing
so far hopefully with a
couple more we'll get it finished up i'd love to see
the actual image on here ha that'd be so great
all right folks so i'll see you next week we'll
be back with whatever happens next
