Construction of new partitions in the apartment. Remaking Khrushchev from A to Z. # 3

Pavel Sidorik. Renovation and Finishing
79 followers
11 Video Views·Dec 11, 2022
New partitions for the bathroom but made from old materials If possible such bricks
I just need to throw it out completely I'm asking myself now why I didn't do it from the start
Friends hello everyone This is Pavel Sidorik a channel about repairs and renovations The next episode of my
The complete renovation of a Khrushchevka from start to finish Here we have already completed the demolition work and replaced the
The front door If you haven't seen these videos be sure to watch them Link to
In the description In this series I will build new partitions for the bathroom but using old materials
Why from the old ones I figured if we buy new blocks carry them up to the fifth floor without an elevator
We also need to get rid of the old bricks again and if we have to carry them outside without an elevator that is
It would result in too much effort Therefore I estimated that we will be building partitions
Old bricks clean them stand them on edge but use good mortar
Reinforce with mesh on both sides Initially it was planned to dismantle only the partitions
Highlight the areas in red and leave the walls of the bathroom After the plaster had been removed
It turned out that the internal partitions were of very poor quality There was no point in reinforcing them
And so I made the decision to take down and rebuild the walls of the bathroom The method I chose for dismantling the walls is as follows:
The most civilized way Remove bricks one by one and place them in the stoves distributing them evenly
It distributes the load throughout the apartment By the way I liked this method because it's quiet the wall is taken apart
Quickly and the bricks remain intact which can be used later In such work it is important
To have a helper to whom to hand bricks Walls need to be monitored to prevent them from collapsing
Entirely With the quality of the old mortar this is quite possible The entire process of dismantling the walls
He took about an hour and a half from us Only traces of the old partitions remained on the ceiling
I'll say right away that these walls are not load-bearing and can be dismantled It turned into a bathroom with transparent walls
The walls And a decent stock of 64-year-old retro brick Enough for a hobbit house
For this work we will need the actual brick itself This is already
It looks like that I will lay it on a mortar I bought a ready-made one but it's thick
Mix them yourself A trowel a float and a putty knife are used to apply the solution
I will tie myself to the wall using slings but rebar can also be used for securing the tie
You can use a drill I will use a staple gun it's with me
He has recently appeared and therefore is eager to work To control
A bubble level will be needed I still have a laser one accordingly
Mixing tank and a helper tool of the kind
Grinders hammers Also the partition can be reinforced with such a mesh inside
And I decided that after building the partition I would reinforce it from both sides
The side with the front mesh Well that's basically the whole set of tools you can
It is possible to get by with a trowel mortar and level but since I have
I have all the tools available I'll work as it's convenient for me I'll start with
markings I take the long wall as the basis which had the bathroom walls attached to it
I drill through the future plaster level and mark it at that level
On one side and the other then I measure the same distance and set the laser up
marking the line of the future wall following the drawn outline
I find a parallel line using a laser axis builder
I mark for the perpendicular wall and also draw a line On the other side I do
Same thing The layout for the future bathroom is ready the most important thing is that there is a
Proper geometry is already in place during the laying stage if considered then the layer of plaster
They will be minimal Before laying the first row I dust the surface
Also to improve adhesion I wet the floor with water Before starting the masonry I find the location at
Use a laser level and tape measure to find the highest point as the floor is very uneven
The highest point is here I will place the brick here I am setting it up
I will use the laser level as my guide I am starting the mixing
I first pour in the water then add the mixture and stir it up
Mixing aid For the first row the mixture must be thick
I am putting the brick in the highest point
I set the horizontal level for the first row of the future I start laying it out
First row on a bed of mortar aligning with the height of the bric
At the highest point and along the laser beam The main thing is to make the first row
At the same level since the floor variations are about 3 centimeters I will check it
orizontal level Thus I set the entire first row At this time
My assistant Yuri was cleaning my bricks as it later turned out to be an occupation
It was enough for 2 days Bricks can be cleaned with a trowel a hammer in general with any tool
Lime is easily removed with makeshift tools The first row is ready everything is set
at the same level I am starting the second row Those who don't know bricks are laid w
Halfway shifted that is with a wrap The second row is already moving faster Then came the
rd row Half a day I managed to lay three rows Every third row I tie to
on the wall for this I use a bracket and a strap mounting gun It can be
Use a percussion drill Such a pistol greatly speeds up the work as the brick o
The edge is unstable for better fixation I align the brick as much as possible to the wall
The next day I brought two more lasers so I wouldn't have to move them
The level had a laser on each plane Good thing I have
The option to take an extra laser level A new day starts with mixing
The solution I've gotten a bit used to it but still not completely there are many problems
827 damn it turn to the window and to me Let's summarize the current situation
It turns out So it's not as simple as it seems Actually if I had gone back
back and would have made the decision of what to use for the partition most likely from these
Bricks and bricks on edge I would refuse Let me explain why First of all myself
The brick is very crooked and of varying sizes with no logic at all Secondly o
It is extremely difficult to set his edge because when you lay down a couple of rows and
You start tapping the next one and you knock the bottom one off Because the bric
Very crooked using a bubble level is practically meaningless because
You end up bumping into some crooked edge It's really uncomfortable This one of mine is like that
The partition ends up relatively straight only because I'm using three laser levels
I set these laser levels on their respective planes One controls this plane
This red one controls the longest plane and there's another laser from this side
Of course you can rearrange them but since I was able to find three laser levels I installed them all at once
So that I don't have to rearrange it And just when placing the brick I make sure it doesn't stick out
The boundaries Therefore I manage to get a more or less even partition Or maybe I just do it this way
A lousy mason If you control it with a bubble level it's all pointless
Because the brick is so different with such protruding edges it's very difficult
If I had used regular blocks I would have built this wall in one day So it's probably faster this way
It will take me three days exactly maybe even four because it's complicated
He is small it's hard to nail you need to take breaks so the partition can set
And the brick itself is very fragile I would rather advise if possible to use such a brick
Just throw them away and buy regular normal blocks and build a neat one from the blocks
A neat partition Laying crooked bricks is a monotonous process that takes a lot of time
But at the same time it is an additional experience and lessons can be learned for the future
The brick turned out to be fragile and very difficult to break into pieces It cracks apart upon impact
By the end of the second day I decided to make a brick cutting attachment for the angle grinder with a connection to
The vacuum cleaner The brick cuts like butter and most importantly there's no dust I'm setting it up myself
Why didn't I make her from the very beginning Friends I'd like to introduce you to Stroybaza company
This is the largest building materials warehouse in Belarus Over 25 000 items in stock
They operate throughout the Republic of Belarus Optimal storage conditions for all construction materials
Materials and their transportation The company fully organizes all loading and unloading
Products as well as free shipping Full range and availability of products
On the website of Stroybaza by you can find out about the availability of goods You can place an order right away
You will immediately see the total cost on the site including delivery and unloading
By placing orders on the site yourself you get a cashback Stroybaz With those
Who dared to do the repair The link to the website will be in the description After that the process went faster
Indeed by the end I had become accustomed to it and felt like a real mason
Finally I reached the opening's lintel and will be able to connect the two partitions into one whole
I used the following technique I simply cut a groove for the reinforcement at the desired height with a hacksaw Installed it
Bricks and the recessed joints were filled with mortar Rebar was inserted from both sides It will serve as a support
A support for a row of bricks that will be above the door opening After that I just lay the bricks
On the solution After placing the jumper the installation became easier because there was no need to cut
Small pieces It seems like there's not much left but this is the most difficult stage of the work because usually
Masons when building such partitions make a platform to work at chest level
But there's no point in going back here because there's only one partition so I'm coming down from the ladder now
I'm putting everything out I have to carry bricks and mortar upstairs The ceilings here in this area are
About three meters The last rows are easier because I know the work will be over soon Yes
And my skill in bricklaying has improved The last row is sloped I cut it like this
Thus leaving a gap of one and a half to two centimeters The junction between the wall and ceiling must be sealed with foam
Apply with construction foam Pre-wet with water to improve adhesion Then just cover everything
I am foaming It is important to do this when the partition has already set Otherwise the foam may
Move the bricks I foam all around the perimeter The partition is ready It turned out very strong
Therefore I decided to do away with external reinforcement and make it only internal
The walls were previously cleaned with a trowel from cement lumps and primed For reinforceme
He mixed the tile adhesive with cement plaster in equal parts The process is very simple Apply it
Apply the solution to the wall spreading it evenly across the entire wall It works very well for high places
The platform helps with the falcon Then press the facade mesh and cover everything on top with a solution
Accuracy is not needed here The main thing is that there are no large bumps since all the walls will be
Plastering I'm reinforcing all the walls except the load-bearing one on the right It's thick and nothing will happen to it
I cast the net only in the corners Considering the reinforcement and two layers of plaster
Outside and inside as well as the future tile the total thickness of the partition will be approximately 11-12
centimeters If I had built a half-brick wall then the partition would have been 16-17
Centimeters For such a small apartment this is a significant loss of space and it would have been necessary
To reissue their passports Here is what I have in terms of expenses This is an estimated cost of the work
The work I did Additional materials I needed The brick used the old one
Here is an estimated cost for the work if I had bought new blocks Here is the comparative cost
The work and material if compared to working with old bricks and working with the purchase of new blocks
The amounts are roughly equal since we still need to take into account the factor that if you buy the blocks
You have to take out the brick The video has ended if you liked it
Of course like the video subscribe to the channel leave comments and click the bell
Links to previous videos in the project will be in the description Wishing everyone a good mood see you again
