Do-it-yourself shower tray for tiles. REDUCING KHRUSHCHOVKA from A to Z # 21

Pavel Sidorik. Renovation and Finishing
79 followers
7 Video Views·Dec 8, 2022
Hello friends everyone
This is Pavel Sidorik a channel about repairs and renovation
In this episode I will be installing a shower pan using
a project
of the exact same bathroom that we did earlier
Only everything works in a mirror image for me
This is probably the only design solution that
It allows to fit a shower washing machine
sink and installation in such a small room
And also leave a little space
Before starting this work I need
to do some preliminary preparation
First cut the grooves and install the electrical
wiring because I couldn't do it as the bathroom is
During electrical work the tool was blocked
Next install the sewage system according to the water level
Then fill all the grooves
I'm starting the work
The wall is thin it's important not to drill all the way through
Of course these tasks are best done during the electrical phase
since the living space is already skimmed and I am conducting
Dusty work
The cable is secured with sections of corrugated tubing
A small tip
I am proceeding to release the outputs to the water
I am mixing the plaster
I am filling the cavity with a solution
I'm temporarily sticking the tiles on the laps
I am displaying everything by level
The fittings extend from the wall by the thickness of the tile
I secure the pipes with construction cement
He will grab it in 5 minutes
securely fixing the outputs to the water
I fill the void behind the pipes with foam
I place the washer on the washing machine in the same way
The cement has set the tile can be removed
I cover the cracks with plaster
I apply it with some extra leaving a small lump on top
When the plaster has set I trim it with
a trowel in this case it doesn't suck in
I also want to go back to the electrical panel
There is no grounding wire in the frushyevka
What does that mean
To ground yourself you need to perform earthing
We did the grounding or rather my
electrician did the grounding who was working here
Viewers were split 50-50 in the comments
Half said yes if there's no grounding in
If you do the earthing in Fruzenskaya nothing will happen
The other half wrote that if somewhere
At the entrance to the house the zero will break burn out
so the phase will go to all equipment all cabinets whic
There is in the apartment
I have studied this issue yes indeed although my
electrician said that such a situation is unlikely
Maybe if such a situation hypothetically
occurs then some measures need to be taken
Therefore the grounding we did in the distribution board
I just disconnect it and it remains installed in the panel
In 2021 there will be a major renovation here in this house and accordingly
They will ground it and then you can just connect
Instead I was recommended in the comments to put
Voltage control relay
This relay is needed to protect the equipment
in the apartment from voltage fluctuations
DS Electronics is
sold in Russia and Belarus
under the brand RBUS and in Ukraine under the brand ZUBR
The relay occupies two modules
There is a trip log thermal protection and setting
Voltage minimum and maximum limits
Price around 50 dollars
Installation
Oleg set the relay
What happens now
First the power comes to the main circuit breaker then
The relay detects the voltage and then
sends it to all other circuit breakers
If we turn off the circuit breaker then turn it on again the
relay does not activate immediately it thinks then it detects
The voltage is applied a click is heard and power is supplied
Marking
I perform the necessary marking with a pencil
I use a laser level and draw lines
Finished
I am setting up the ramp and pipes The
height of the pallet I will pour depends o
From the height of the hatch and the
height of the hatch depends on the outlet
You need to take the correct slope into account My trap height is 19 cm so my tray will be
At least 19 cm it will be higher because I need to account for
another drain make the proper slope and the edge will be even higher
A little higher
Now I need to level the ramp and secure it
put some mixture underneath so it can set
The mixture will consist of plaster and expanded clay
I'm mixing
It turned out to be a flexible mixture with a light aggregate
which makes it convenient to place the trap and pipes on it
I pour the mixture and level the trap
While the solution is setting
you can proceed with pouring the border
Cofferdam
I will make the cofferdam from the wall of an old wardrobe
I mark and cut the MDF into strips and
I attach the guide for a straight cut
I made a few scratches on the box but it's not critical
I start assembling
The MDF is connected from the top using a
board with an inner width of 60 millimeters
This looks like a foundation formwork
Tightening two screws to prevent the formwork from shifting diagonally
If it shifts
diagonally then accordingly
The internal distance may change
Holes need to be drilled for the pipes
I screw in the anchors I had available into
the concrete for additional edge reinforcement
I am setting up the formwork in place
I use plaster to secure the formwork from below
Now it is possible to proceed with the pouring
Usually the base and the curb are made of bricks
I decided to do it differently I'll tell you why now
If you build the edge with bricks you end up having to
plaster three surfaces which
takes time and is extra work
It's simpler to pour the entire curb at once according to the level
One of the best materials suitable for pouring
It is a concrete mix Holcim M300
Instead of reinforcement I am adding fiber for the concrete
I'm mixing
I pour concrete mix into the formwork
Now we have to wait until he grabs it
I am checking everything once again at the current level
If needed the formwork can be adjusted
The concrete set the next day the only
problem was that it settled significantly
I need to mix the cement-based plaster now and
apply it level with the top edge of the MDF
The only thing to remove was the
cement milk that was visible on top
The concrete is still soft for now but in
just one more day it will become very strong
I am cleaning up trash
I am patching with plaster
In general of course the formwork should be removed
when the concrete has set
well after a week maybe two
But since I don't have time and I need to continue
working I need to remove at least the inner part
So I will now carefully try to remove
it in order to pour the tray further
Take it off carefully so as not to break the edge
Note how flat the
surface is for tiling
Places where there were boards I fill them in
Filling the tray
Once the rim is poured you can proceed to fill it
The entire tray space is filled with expanded clay aggregate and cement
Expanded clay aggregate with cement is light and hard
If I had laid all the bricks the weight would
have been significant and the labor higher
I mix the expanded clay aggregate using the
same technology that was used in the floor screed
Expanded clay aggregate cement binder
I am doing the following
I have set up a laser level
Here is my trap level
The filler will be 4 centimeters below the level of the trap
On the expanded clay I will also pour concrete mix
So I need to pour in here 4
centimeters lower than the trap
I will pour the rest with concrete mix
I mark the desired level and will now fill with expanded clay
I check the level of the expanded clay aggregate with a laser
The tray will be level with the edge on the left
Installing guides and pouring concrete mix
Cutting the guides to the required size
I am sealing the drain with PVC tape
I am proceeding with the installation of the beacons
Once the formwork is in place you can proceed with pouring the concrete
I will use concrete mix as the screed I am
mixing the concrete mix
I will not reinforce it
Instead of reinforcing I add fiber
You can pull it unevenly
The main thing is to have a surplus as the cement sand will be trimmed
Finished
Trimming
The next day I start trimming
The concrete has already hardened but has not yet gained sufficient strength so it is scraped off
This allows to remove all bumps and level the base
The edge of the heart pan is leveled by the renovator
It would have been possible to just punch it with a hole punch but then the appearance would have been untidy
Now everything can be removed and the formwork can be taken off
The work is done
In my opinion the pallet looks nice
Estimate for materials and labor
Well the video is ready
The video has come to an end
Thank you all for your attention
If you liked it of course like the video subscribe to the channel
Click the bell leave comments
Wishing everyone a good mood see you again
Subtitle Editor A Sinyetskaya Proofreader A Egorova
