896. Complete Guide to a Throw Lidded Jar with Hsin-Chuen Lin~ PAAC class demo

Hsinchuen Lin
205 followers
242 Video Views·Jun 24, 2026
To see or buy my finished work and pottery tools, please visit my Online shops:
https://sawfish-endive-kgks.squarespace.com/shop
http://www.etsy.com/shop/hsinchuen
http://www.etsy.com/shop/hsinceramics
http://www.etsy.com/shop/hsintools
To watch more of my YouTube videos, please visit my channel:
http://www.youtube.com/@hsinchuen
To learn more information, please visit my Website:
www.mypots.net
Instagram: @hsinchuenlin
Facebook page: Hsin-Chuen Lin Ceramics
Pinterest: @hsinchuen6518
AI Generated·May contain errors
and you can see all my arms folding together. Center and open it. Use the thumb and then
take it all the way to almost half of it and then widen the base. Okay my left and right
Fingers are both inside to help make it wider and now clean up the base. Use the pad of your
fingertip to compress from the center towards your right or from your right
toward the center. You can do that a couple times or if your fingertip is not strong
this is one of my tools. Hold it on your both hands and then just squeeze and push down.
Okay so it's very easy or if you have this kind of tool you can use that but
that tool is specifically designed for compressing the floor so there's a little curve here a little
curve there so it's not gouging it. This is a little bit harder because if you cross over
my gouging by the corners but you can use that to do that and also this is a little bit too wide
and that is smaller so it can move more freely. Okay so the base is good and then pull up the wall
first always lubricate it make it slippery and grab the pinch grab these two fingers are
the thumb and the fingers are doing the job. The right hand is just to stabilize it
and place it right here. Slippery grab pinch and go straight up let go squeeze the rim a bit
again when you want to touch the clay make sure everywhere is slippery.
A bit of water a little bit slip and if you want the base slightly smaller you can squeeze it in
like here use my right fingertip just pinch and the left hand stabilizes the wall while I'm
pinching it right left hand here and you see that where's my arm where's my wrist it's always
placed somewhere right and pinch it so the base is a bit smaller now and then there's one other
technique to get your wall taller sooner faster collar make it taller collar squeeze squeeze
squeeze squeeze and the wall and every time when you touch the wall you pull up or you collar
control the rim to make it level if you don't do that start to get wobbly worse and worse
again when you want to touch the surface make sure everywhere you touch it is slippery okay
right so that's good now my thumb is too short to stop moving the clay from the bottom corner
so I'm extending my right thumb like this the hand is like this right this this right grab the clay
and pinch the same way like I'm using my thumb my left thumb right
and I will do one more time slippery again
uh well um so a lot of people are doing equally same level to move up the clay
that is not very efficient so if you try to stagger it either inside hand is lower outside
hand higher or inside hand higher outside hand lower it's like it's like a scissors when you
cut the paper you wouldn't cut it this way right but if you stagger it you can cut the paper right
easier the same thing when you move the clay stagger it's it will get it moving up more
both both yes okay slippery again and my way of doing so is that outside hand is slightly lower
than inside hand but some other people they do inside hand lower the outside hand okay
and slippery again right first push out a little bit better here right the finger goes into the
corner and squeeze out you see that there's a little belly now my thumb is holding right
underneath of the belly so I always push up the belly okay slippery and when you are not moving
you stay on the same spot for a long time you tend to wipe up the slip that's why you feel
if you are moving too slow you will create more friction so you have to one for revolution you
move up one notch okay every time depending on the wheel you see that my wheel isn't going
very fast if your wheel are going fast right fast then you have to move your hand faster
which is not my style I usually like to have a slow but very stable control okay so that is the
speed that I'm used to right belly and both hands squeeze out you see that my thumb is sitting
underneath of the belly and this time I'm slightly to widen it up so when I pull up the same time
I'm also shaping and again compress the rim okay now if you don't make it thinner you can keep on
pulling it up but I usually don't do that okay you just increase make enough thickness maybe a
little bit thicker than quarter inch and I will start to stretch when you stretch it out your
wall becomes thinner okay so now I'm going to stretch it out so the inside hand looks like this
right you see that one two three four all four finger pad that pad not a nail part the pad
is pushing out pushing out this way right make sure slippery right and outside hand
just to stabilize it and if you want to increase it push harder then increase the volume push
harder but the outside hand is stabilized like fingertip to fingertip push out and outside hand
is stabilize it okay this is that see that now if you want to use the rib same way right same way
you use the wooden rib make sure slippery hold it there and push that against the rib and your rib
is going along with the inside finger same way right or if you want to use the metal rib
same way right not here not like this right this is like a 90 degrees usually I'm holding this way
okay the rib and push that if I want to have more curve my thumb squeeze hard and the thumb is
controlling the curve okay my thumb is controlling the curve okay if I want to have more curve my
thumb squeezing harder and push the wall onto the curve I pushed and you can go up and down
that's no problem just smooth it out the finger mark right so now the finger mark is being removed
okay so that is the shaping pull up and shaping now for making the rim for your lid jar
so there are a couple ways to make the lid jar you want to put the gallery on the body or
you want to put the gallery on your lid or you're going to put both gallery on body and your lid
that is a little bit more difficult okay more complicated because you need to measure two parts
of it so first I will show you the simple body just make this part here as a simple body put my
gallery on the lid okay that is the usual way I make my lid part but you can also do the other way
put the gallery on the body and make your lid simple okay so either way should be fine
or you're going to show off your skill then you put both gallery on the body and on your lid
okay all right now this part here usually when you're making little part keep the rim slightly
thicker see that when I'm stretching I didn't even touch the rim I just keep on compressing it
so this part here before I do that make sure my base is nice and clean just clean up okay and you
can see that there's nothing in there no no slip or no water it looks very dry and then if you want
to make your lid smaller you can close it in okay there are a couple ways to close it like here
you can move it like this six point one two three four five six six point touch and then you squeeze
and slide and pull up okay but make sure when you want to do that that surface should be slippery
okay so usually I just use a sponge to touch up that spot that I want to touch not here right just
touch it up here and then six point right so that's one way to do it or there's another way
to close it too this way okay make sure it's slippery this you close it okay but this way
when you do that you only push it down this you kind of grab it and then you slide it pull up
okay so it's different way of doing it all right so now let's open up also there's another way to
close it is that you pull the clay toward the center okay so this is metal put your finger
underneath inside underneath on the inside and for the shoulder you're holding this right and
then the outside hand this hand this finger is supporting it and the outside finger is squeezing
it so the shoulder is being stabilized so you don't get wobbly you do that is you want to do
outside hand so sometimes it gets wobbly but when you do it so you are supporting the shoulder so
it's more stable and also if you want it you can also pull right here right this hand
grab the clay right here if you find out there's more clay here you just pull so you move more clay
from the shoulder so this part here becomes thinner and that's how you close it and you can
keep on going second way you want to push this right so sometimes you just go cover it like that
yeah flat but the first way you pull is like you lift it right so that is the closing right
closing closing closing you see that i'm pulling the clay toward the center so this part here even
now it's getting thinner and the opening is smaller okay so that is how you close if you
want to close it but we are making a jar so we don't make it small unless you make small opening
part so i'm going to open it up again and the rim is slightly wobbly so you could level it first
so first i show you i told you that i will show you make it simple right simple by just forming
a neck here right simple neck and put the gallery right here on the lid when you throw
you're going to trim the knob later and you put gallery here so the gallery here
fit in there so your pot is not moving this is slightly too narrow so let me wait and see if i
can i throw this at different time this i made it last week oh let's see still too big yes when you
make in the lid you want to throw at the same time so you keep the same moisture because this
i made it last week so it's for strength so if i have the same diameter now this part here is
okay then it won't fit but i just want to show you that's how it look like put the simple body
and make your gallery on the lid so that's how how you do it okay and now let's make the gallery
on the body and again to be able to make the gallery this is a little bit too thin you don't
have enough clay to make the gallery so slightly squeeze it down make this part here slightly
thicker and wider pinch here and squeeze it from the top see that part is thicker and then about
half you push down you create a gallery there okay so how do you create a gallery get something that
the tool that has sharp corner you can use a metal anything with 90 degree sharp corner
if you have a basic kit sometimes that your grip is not this part here is wrong you could use the
same paper to set it down to make 90 degrees okay so this i'm going to use that and push from the
middle part and push it down this is how i grab it this 90 degrees put the finger there and push
it down but you want to have a bit of support so put the finger underneath to support it and you
see that everywhere i stabilize it right stabilize it here stabilize here and okay make the gallery
and clean up here gallery so for that gallery there you can make very simple just a little
dish with a knob and then sit inside so your your lid is going nowhere so that's the way to
make your gallery on the body so you can make a simple lid just follow that angle here
and chop it off and of course you need to measure it right so if you want to do the simple
simple lid so all you need to do is measure that inner part of the gallery so that's the size and
then you just make a small dish and you can trim the knob later or there's other way to make the
let me show you how to do that on this part here actually this part here that inner part
this inner part of a gallery and the outer part of a gallery it's adjustable when you are trimming
you can trim down a bit so that usually you do the adjustment when you are ready to trim okay
and like this one here right if i measure it good enough so this this part here
fitting inside and this part here fitting the outer part of it so that's why if you have the
skill you want to show off you do that okay put gallery on either or on both the lid and the body
talk about the lid making so first i will make a simple lid just a small dish for that
just pinch smaller amount of clay right here so i'm going to make a small dish
like that and then you trim the knob later i trim the knob later so since you are going to
trim the knob so your base could be smaller right you see that this part will be this part here will
be the knob and then you will you're making a small dish and slightly the curve looks better
if you have that too flat it's not follow you see that you have curve and then you
you have a straight top flat top doesn't match so you want to have slightly dome that looks
better and i find out this part here your thumb you have a very good curve here so i use that
curve to push out and have my right hand outside to support it right and of course you need to
check to see if that is that size or not a little bit too big so you could chop it off
double check it again still too big so you want to do a little by little
but you see that when i'm cutting it all my part of my body is connecting together to stabilize
if you have a hand here it's moving right so stabilize it and then around the corner a bit
and second chap again so that's good perfect and then here will be your knob so you are going to
cut it right here and remember last time i told you throw up the hum you use a wooden knife to
undercut it so your string can sit right there if you don't have the cotton string
just go like this and then you got it right so this part here then later you can design
design your knot to fit it in the body so that is the simple way of making
a small dish to fit if you have a gallery on the body now let me show you a different way of
making the lid and usually throw up the hum you just grab the clay from the top portion
right this is the part here and then this time i'm going to throw the knot throw the knob
you grab the clay from there and forming a knot right this will be your knob
and then here you move out squeeze it in so the knob is smaller looks more elegant
and when you throw the knob you don't trim the knob so you might want to make it look nicer
right and make sure you got enough so you see now i don't have enough so i can pull the clay outward
to extend it so grab the clay from here and pull it out still not enough so that's good
right so that's you throw your knob and then this part here is hanging in hanging in there
that's good and then to cut it so my tip for you because usually this is very hard to trim
when you turn it upside down so you want a minimum of the trimming so what you do is
you cut this part here as thin as you can right and almost break just a tiny bit
and then later you can just wire it off wire it up but when you try to pick it up you might mess
up with the rim so actually i am cutting the clay right here so there's a little pedestal
for the lid to sit on so when you holding it you just pick it up from there and later you
just use a wire to cut so it's much easier okay
you could do that yeah see that so that is only really little so you can cut it easily with the
wire and here you don't mess up the rim right so you hold it there now let's do a gallery okay
and this method is also just like that one like i just showed you right so put the gallery on
the lid and again when you throw something that is smaller and you want to cut it off
that's called a throw up the hum right so when you throw up the hum usually you are centering
your clay into this shape like a doorknob right doorknob and this part here will be the lid
will be the knob this part here this smaller portion and then you open up
a dish again and this you are going to put your gallery here so make this part slightly thicker
so you see that i'm pinch it here so this part here is slightly thicker
and then we want to make sure that is the size we want it so it's very close to the size we want it
that's the lid i show you that one so make a shallow dish right with the curve and slightly
deeper because you are going to trim a slightly dome shape so you your inside should follow the
outside so if you want about make a curve on your lid you also want to have a curve on the inside
of this part here right like i told you that this part here it's good and then you're going to use
a good sharp 90 degrees and put your hand here to support it and then you push down in the meantime
you squeeze it push down and you squeeze if you want this part here especially when you have
like a teapot you want to pour so this part here could be a bit longer so when you pour
it's not easy to fall down when you are moving or when you're pouring the water or liquid or tea
so you can push it down further down make it slightly taller this is probably not tall enough
if you're not about to you could do a bit taller there's uh you open up deeper and then you push
down harder so you can have have it deeper there this is probably a bit too wide already so
see that a bit too wide what do you do adjust
this part here might be a bit consider that the body is that the gallery is hanging out further
so this part here might be too small you could adjust it by squeeze it in right this part here
right this part here is wider to push it in and clean up clean up and one other way um
when i'm making my upside down i call this upside down turn in the knob i usually dip
this part here slide steady this slightly angle so it's easier for the lid to drop down
slightly not too much but slightly taper okay taper so it's easier for let's drop it
to the position okay so that is the lid and then you are going to trim the knob later so we can
just make sure you leave enough space for your knob so here will be the part i'm cutting it
and there's a still lots of clay here you could wet trim it so i live in enough if you don't have
enough you can also add a piece of clay and throw after you trim put a piece of clay there
and you can throw your nut okay that's also okay too but usually i don't do that i just
keep enough clay too so that i could trim it easier and uh for me mind love
like you design different type of
